Search Documents

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By A. Pawelczyk, D. Hreniak, E. Zych, W. Strek, K. Grabas, A. Ostrowski

"Nowadays recycling became an important rare earth elements (REE) source, which allows to reduce their demand for extraction from natural deposits. At present, the used fluorescent lamps and old type TV or computer monitors kinescopes are selectively collected and undergo processing in the system of recycling. It has been estimated, that utilization of such waste would be sufficient to cover the REE demand for the next 5-8 years. In the developed process, the luminophores were separated from the electronic and electronic waste materials, and processed by hydrometallurgical methods to obtain concentrated REE in form of oxides. INTRODUCTIONInternational Union of Pure and Applied Chemistry (IUPAC) defines the rare earths as a set of seventeen chemical elements, specifically the fifteen lanthanides plus scandium and yttrium. They are considered the most important indicators of the developed technologies and techniques. Rare earths are used, amongst others, for the production of magnetic and superconducting materials, ceramics, lighting, catalytic converters, advanced electronics and alloys. The demand for RE continually increases, similarly to many other primary raw materials. Globalization, the growing demand for limited resources of raw materials, the policy of the countries controlling the raw material market and the economic crisis became a spur for new programs of socio-economic development of the European Union (EU), with particular regard to EU safety for commodities in intermediary as well as long-term horizons (COM 2008), COM 2011).EU countries import most of metallic and chemical raw materials important for their economy. In 2008 a detailed program named Raw Material Initiative was announced. The increase in demand for most raw materials having special importance for the development of technology, and access to of raw materials security of supply affect the future economies of the UE member states and other developed countries."

Jan 1, 2012

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and bubble size (Db) in the collection (pulp) zone of full-scale flotation systems. To obtain conclusive evidence exclusively related to the collection zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that generating small (1 mm) bubbles had a significantly higher beneficial effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of liberated coarse particles was close to zero, but could be recovered almost completely by reducing bubble size. The evidence revealed an apparent inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb did not always result in higher recovery, as the model predicts. Overall, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only under highly suboptimal bubble size conditions (Db = 3 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, for the most part, both the bubble generation method and the froth zone played inconsequential roles. An empirical model that better describes the kinetics of particle collection is proposed.INTRODUCTIONStudies showing the link between metallurgical performance and the interactions of bubbles and particles in the collection (pulp) zone of industrial flotation systems are scarce. A common belief among a number of mineral processing practitioners considers that “small” bubbles are favourable to recover “small” particles and that, conversely, “larger” bubbles are more efficient at floating “coarse” particles. However, perceptions like this are often substantiated by anecdotal evidence rather than by rigorous data analysis. What is the optimum bubble size for a particular case, how operating conditions can be adjusted to control a target bubble size, and whether the bubble size needs to be changed in the first place to optimize the operation of a flotation plant are questions that usually remain without solid answers.The studies reported by Hernandez-Aguilar (2010, 2011) were, in part, performed to test the effect of bubble size on flotation response and, thus, help address some of the above questions. The focus of the studies was to optimize the metallurgical grade-recovery performance of the Cu-Mo separation plant at Teck’s Highland Valley Copper mine (HVC). The outcome was compelling and significantly valuable: consolidated production data showed that in 2008 – the year when the recommendations from the studies started to be implemented – the Mo plant recovery was 89%, and gradually increased to 92% and 94% in 2009 and 2010, respectively, along with an increase in Mo concentrate grade. (Note: these production figures were not included in the publications quoted above; however, they were shown during an oral presentation at the 43rd Annual Meeting of the Canadian Mineral Processors in 2011.)"

Jan 1, 2016

By Gerald S. Cole

It used to be that a science/engineering presentation on "light weight" at a metallurgy conference, would relate to the materials science, processing, component fabrication and applications of aluminum, magnesium and titanium. Within the automotive industry, light weight now includes how to "lighten up", how to lightweight, or how to mass reduce vehicle components and systems. Increasingly stringent global emissions-reduction requirements require increasing vehicle fuel efficiency; mass reduction is an enabler to achieve this. While light metals certainly are the basis, a host of other materials can be used to optimize mass reduction while meeting vehicle performance, safety and cost requirements. New grades of ultrahigh strength steels and even nanosteels can be thinned down and save over 1/3 the mass vs conventional mild steels. A compacted graphite cast iron engine can be made lighter than an aluminum one. Aluminum components in vehicles were only castings; now aluminum stampings, forgings and extrusions are becoming more visible components of mass reduction. Lower mass high temperature polymers, and carbon fiber polymer composites now replace aluminum and steel. These materials often require specialized processing and manufacturing techniques to produce a component, including superplastically formed twin roll cast sheet aluminum and magnesium, and hot stamped/in-mold quenched steels. The assembly of hybrid structures requires unique joining/bonding, and corrosion-inhibiting techniques that might include sophisticated structural adhesives. This thinking "light" presentation, will conclude with a discussion of U.S. and Canadian government engineering and research support for mass reduction, including the proposed $148 M American Lightweight Materials Manufacturing Innovation Institute.

Jan 1, 2014

By D. A. Beck

The load-deformation response of discontinuous rock under static and dynamic loading conditions has been simulated using Explicit Finite Element models. The intent of the analysis was to investigate the effects of specimen size and confining stress on strength, dilation and comminution. The simulations allow the development of homogenised constitutive material properties for discontinuous rock masses using laboratory scale measurements and representative Discrete Fracture Networks (DFNs). A procedure for this is presented which includes a comparison of measured seismic response in a mine to the Dissipated Plastic Energy (DPE) that is released in the simulated rock masses. The models also show how confinement and scale affect the stress-strain and DPE response of the simulated rock specimens, reproducing a number of known rock phenomena that are often poorly captured in geotechnical modelling. A case study is presented showing a satisfactory match between the model-derived, homogenised material properties and values achieved by calibration of a mine-scale model where many thousands of seismic, displacement and damage measurements were available.

May 1, 2009

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009

By J. D. Bateman

DURING the summer of 1942 several chromite deposits were discovered in the Lac du Bonnet district about eighty miles northeast of Winnipeg. The deposits are confined to the Bird River complex, a folded composite sill of basic and ultrabasic igneous rocks of early Precambrian age that lies to the north of Bird river (1). The outcrop of the sill represents the trace of an easterly plunging anticline, the south limb extending from the northeast bay of Lac du Bonnet eastward to Bird lake, and the other limb, 6 to 12 miles north, lying between Maskwa river and Euclid lake. The south limb of the sill is 20 miles long, and the northern counterpart 15 miles; but its continuity is interrupted by faulting and by the intrusion of younger granite, so that the total length of outcrop of both limbs does not likely exceed 25 miles. The sill is intrusive into early Precambrian greenstones and associated sedimentary rocks. The chromite discoveries have been made at several localities on both limbs of the sill, and in each case at the same geological horizon. The sill comprises an upper layer of hornblende gabbro and a lower layer of serpentinized peridotite, and altogether is from 500 to 3,500 feet thick. The chromite zone is within and near the top of the peridotite layer, and thus about midway of the sill, both of the limbs of which stand nearly vertical. This geological relationship was established early in the exploration of the initial discoveries and served as the basis for successful predictions of later discoveries. The chromite zone probably persists throughout the length of the sill, but its width and chromite content are not everywhere the same. The initial exploration along both limbs of the sill has shown a combined total length of about 12,000 feet of chromite ore varying in width from 6 to 12 feet. In many places the overburden is thick and obscures the continuity of the chromite zone; but as investigation proceeds the known deposits will be extended and new ones will be found. Thus, although a total length of 12,000 feet of ore has been investigated up to the present time, there is an indicated length of approximately 31,000 feet along which the ore is more than 4 to 5 feet wide. This estimate is based on geological considerations and represents a total tonnage in the order of 15,000 tons per vertical foot of depth.

Jan 1, 1943

By N. J. Contini, R. W. Knopp

"In March 1988, old Denver flotation cells were removed from Dickenson's Arthur w. White Mill, and a new flotation circuit, consisting of four Prochem rougher cells and a Hydrochem agitated cleaner column, was commissioned. The refractory portion of the gold in the ore is associated with arsenopyrite, therefore the flotation circuit is set up to produce a saleable sulphide concentrate. Tailings from the leach circuit are conditioned prior to being pumped as feed to the flotation circuit. The prototype Hydrochem agitated column has been in operation as a single cleaner stage for rougher concentrate. The effect of flotation circuit changes on gold recovery data, as well as cleaner concentrate production, and development work to achieve the target results, have been investigated. Flowsheet modifications and the resulting circuit performance data, along with test results to date, will be presented.INTRODUCTIONThe mill is capable of treating 1000 stpd of ore averaging approximately 0.30 oz/ton Au. The ore is crushed and ground to 75% - 200 mesh. Gravity concentration, cyanidation, and Merrill - Crowe precipitation yields 84% gold recovery. Detailed descriptions of the comminution, gravity separation, and leaching circuits, as well as background information have been presented elsewhere (Suttill, Van Weert et al). The target cleaner concentrate grade is 1.0 oz/ton Au for custom smelting and refining. Historical gold recovery values of the old circuit was approximately 20% of the gold present in the float feed at the target grade. The recovery value objective set for the new circuit during the planning stages was 50% of the gold present in the flotation feed at 1.0 oz/ton Au in cleaner concentrate."

Jan 1, 1989

By M. H. Colebrook

Nickel laterites contain about 70% of all continental or terrestrial nickel resources; therefore the recovery of nickel from lateritic ores has large economic significance. The processing of lateritic ores involves the preparation and movement of concentrated aqueous suspensions. However due to complex characteristics and non-Newtonian properties, ranging from shear-thinning to shear-thickening and from thixotropic to rheopectic, a basic understanding of the flow behaviour must be developed. This understanding will assist in the development of new plants and the operation of existing plants. The work in this paper involves the characterization of three ore types from the Vermelho ore deposit to categorize them as rheologically simple to complex. Rheological testing was also conducted on pure mineral samples that represent the main minerals in these samples. The results show that the rheological properties of the ore types can be related to the surface properties and physical characteristics of the main mineral constituents.

Jan 1, 2006

By Simon C. Dominy, Ian M. Platten, Garry F. Johansen, Alwyn E. Annels, Brian W. Cuffley

Abstract - Coarse gold-bearing veins are characterized by high grades that are localized and erratic. Effective sampling of coarse gold-bearing veins is difficult because of the low concentration and erratic nature of the gold particles. Diamond drilling is an effective measure of geological continuity, however, grade distribution can only be reliably obtained from underground development (including close-spaced sampling, bulk sampling, and trial mining). Comparison between surface and underground drilling, underground linear/panel and bulk sampling indicate that drilling and linear/ panel samples generally understate bulk sample grades. Bulk samples are likely to be the closest estimators of true grade. It is unlikely that anything above an Inferred Resource category can be estimated from surface drilling alone, and at best the grade will only be a global estimate. Underground development, in-fill drilling and bulk sampling/trial mining will be required to delineate Indicated and Measured Resources. Closely spaced development and bulk sampling is likely to be the only way to determine Reserves. The resource estimation process must driven by a clear geological model that should attempt to understand both geological and grade continuity. Traditionally, grade interpolation has been undertaken using classical methods, though more recently, computer-based block modelling techniques have been used with some success. Three case histories are presented, documenting the problems of estimating resources in coarse gold-bearing veins and the practical ways in which they were approached.

Jan 1, 2000

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By Ahmad Ghahremaninezhad, Denver H. Cowan

Much of today’s gold is locked within sulphide minerals. These sulphide minerals, including pyrite, need to be subjected to oxidative pre-treatment in order to leach the refractory-gold using traditional methods. Typically autoclaves employing high temperatures between 180?225 ºC, and extremely high pressures between 1,500?3,200 kPa, are used for the oxidative pre-treatment. However, the autoclaves themselves are very expensive, costly to operate and maintain, and produce excess sulphuric acid. This paper studies the atmospheric oxidation of pyrite in ferric sulphate solutions. In general, pyrite oxidation under atmospheric pressure can result in high elemental sulphur production, i.e. less acid generation. Activated carbon has displayed an ability to catalyze the process, achieving reasonable kinetics. The reaction kinetics were investigated by altering acidity of the leaching solution, temperature, catalyst ratio, sparged oxygen and agitation. A combination of X-ray diffraction, scanning electron microscopy, optical microscopy, X-ray fluorescence, inductively coupled plasma mass spectrometry (ICP-MS), and atomic absorption spectroscopy (AAS) were used to monitor the kinetics of the process and elemental sulphur yield. The purpose of this investigation was to determine optimal operating conditions that maximized kinetics of the atmospheric oxidation while maximizing elemental sulphur yield.

Jan 1, 2015

By Yuki Tsunazawa, Shuji Owada, Sho Fukui, Chiharu Tokoro

"Since the amount of e-waste has been rapidly increasing all over the world, there is a desire to develop the effective recycling process. E-waste has various kinds of electronic components with valuable and/or hazardous materials. Recycling of them is an important subject from the viewpoint of both the recovery of valuable materials and waste treatment. In common with all mineral processing, the comminution of e-waste is a key process because the liberation states after comminution determine the overall efficiency of metal recovery. Since some of useful critical metals are concentrated in a specific component, a special and selective grinding is expected to be effective. However, the knowledge about the mechanism and the effectiveness of the selective grinding is still limited and unclear.To better comprehend the mechanism, in this study, the investigation of comminution process using the particle-based simulation was conducted. Especially, this study focused on the comminution performance of printed circuit boards (PCBs), which are major components of e-waste. The behavior of PCBs and airflow in a drum typed agitation mill having flexible chains was simulated by the discrete element method (DEM) coupled with computational fluid dynamics (CFD). To model the shape of PCBs, the particle based rigid body model was introduced into the DEM. Since this model could not directly simulate the breakage phenomena, collision energy was calculated to qualitatively evaluate the comminution performance. In addition, the simulation results were compared with the experimental comminution tests using simulant PCBs where some capacitors were solder-mounted. These results indicated that comminution performance was affected by the rotation speed of the agitator. It was also demonstrated that the comminution performance was qualitatively evaluated using the particle-based simulation and this particle-based simulation made it possible to investigate the mechanism of e-waste comminution."

Jan 1, 2016

By A. Banerjee, J. P. Weiler, J. Jekl, J. T. Wood, R. Berkmortel

"The work presented here is part of an ongoing project designed to develop predictive capabilities of the local mechanical properties, and thus, structural behaviour of a thin-walled high-pressure die-cast AM60B magnesium alloy component. This work focuses on developing correlations between process parameters and local microstructure. Numerical simulations of the die filling and solidification behaviour of the AM60B component were used to estimate local process parameters such as solidification rate, temperature gradient, filling velocity, etc. These estimated parameters were used to establish semiempirical correlations with measured VALUES (of the local microstructure measured in regions throughout the component of different solidification conditions. INTRODUCTIONHigh-pressure die-cast magnesium alloys are experiencing increasing use in structural automotive components. A strength-to-weight ratio comparable to steels and its ease of castability allow for these alloys to be utilized in such capacities as instrument panel beams, seat and door frames, and engine cradles, among others (Gjestland and Westengen, 2007). However, the current use of these alloys is limited due to variations in local mechanical properties. These local property variations restrict part designers to assume lower than actual properties, resulting in larger sections, thus diminishing the light-weighting advantages of magnesium alloys. If these local property variations could be predicted, part designers would be able to optimize die-cast magnesium alloy components and fully take advantage of the light-weighting capacity of these materials.The work presented here is part of an ongoing project aimed at developing predictive capabilities of the local mechanical properties, and bulk mechanical performance, from variations in local microstructure, and ultimately from local process parameters in die-cast magnesium alloys. This project, unique in its nature, is based upon the results determined from fifty sequentially cast AM60B magnesium alloy instrument panel beams provided by Meridian Lightweight Technologies (shown in Figure 1)."

Jan 1, 2012

One Data Set for the Lifecycle Complete data captured at the logging stage benefits the entire life cycle Exploration Technical Studies Production and Milling Visible Light Spectrum Hyperspectral, put simply, is the interaction of light with matter based on the nature and chemical structure of the specimen. SpectrumWe develop the library to match the liberation size fraction Analyses every 1mm2 1 meter of NQ core = 35 000 analysis data Crystal size detection : 0.1 micron

May 1, 2013

By N. Ahern, M. Barbanell

Mercury is often present in gold ores and can be released during processing. In view of health and environmental concerns related to mercury, the mining industry takes leadership in the responsible management of mercury. This paper reviews various aspects of mercury management, including an overview of mercury deportment in typical gold processing flowsheets; trends in mercury legislation impacting the international flow and management of mercury in the gold mining industry; and treatment, storage and disposal options for mercury and mercury containing materials.

Jan 1, 2014

By Desmond M. Levins, Reginald K. Ryan

"Removal of radium from uranium tailings would substantially lessen their environmental impact because it would eliminate, or greatly reduce, the hazards arising from radon emanation, leaching of radium, dust dispersal and gamma radiation. A process is described to extract radium from tailings by leaching in 3M Nael solution. The radium can be rapidly leached at ambient temperatures by either multi-stage contact in agitated vessels or washing on a tailings filter cake. Extraction efficiencies ranging from 80 to 94% have been measured for tailings derived from a number of Australian ores.Methods for radium recovery from the leach solution by precipitation, ion exchange and adsorption have been examined. Precipitation as barium/radium sulphate appears to be the most suitable approach. A possible flow diagram for the process is proposed which involves recycle of the saline leach liquor.IntroductionDisposal of mill tailings is the most contentious environmental issue facing the uranium mining industry. The conventional approach to managing tailings is to store them in a dam above ground. Attempts have been made to stabilize some tailings piles by physical or chemical methods. In a few cases, the tailings have been covered with earth and revegetated. However, most tailings piles from abandoned mills are in a neglected state and subject to the erosive and dispersive forces of nature. The cost of remedial action is high. The United States Department of Energy (DOE) has estimated that it will cost up to $130 million to rehabilitate abandoned mill sites in the U.S .A..Environmental authorities are now insisting that uranium mining companies improve their methods of tailings disposal. In the United States, the preferred approach is burial, either in mines or in specially excavated pits. Tailings retention systems as operated in Canada are regarded as storage facilities until an acceptable method of disposal is found. In Australia, the Fox Commission recommended that tailings from the Ranger project should be returned to the open-cut mine. Returning tailings to the mine has considerable merit, but it is not always a viable option. In many underground operations, it is not physically possible to fit all the tailings in the worked-out mine. In other cases, the groundwater hydrology of the mine may be unfavourable."

Jan 1, 1980

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005