Search Documents

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By W. D. C. MacKenzie

IT IS almost exactly fifteen years since the discovery of the Leduc oil field and, as this luncheon is part of the Thirteenth Annual Technical Meeting of the Institute's Petroleum and Natural Gas Division, it seems, therefore, a singularly appropriate time to discuss the theme which the program committee has suggested for the occasion -the progress of the Canadian oil industry during the fifteen years since the discovery of the Leduc field. As you will see, I plan to take a few minor liberties with this suggested theme. I shall present ample evidence of growth and progress, but, at the same time, I want to refer to some areas where progress has been anything but conspicuous and to see what can be learned from these areas for the future. The achievements of the Canadian oil industry since the Leduc discovery in 1947 have been substantial, and the public is relatively familiar with the more spectacular developments.

Jan 1, 1962

By P Hulteberg

In this article, an integrated catalytic reactor design approach to produce PEMFC-quality hydrogen is evaluated. The design is based on a high level of heat exchanging perfonned internally, highly active noble metal catalysts and a woven wire mesh catalyst support system. It consists of an integrated steam refonner and a catalytic burner section, a water gas shift section and a preferential carbon monoxide oxidation section. The reactor design is described and experiments perfonned to evaluate the two reactors built are reported. The two reactors have a maximum output of 3 Nm and 10 Nm3 hydrogen/h respectively. In the larger unit, a total of six fuels, three gaseous (methane, natural gas and liquid propane gas) and three liquid (naphtha, ethanol and methanol), were evaluated. The larger unit was also used to investigate how variations of parameters such as steam-to-carbon ratio in the steam reforming part of the system and the relation between oxygen and carbon monoxide in the preferential carbon monoxide oxidation affect the reactor perfonnance. The smaller unit was used, after implementing automatic control, to run a system life time test for 480 h. The refonner system perfonned according to specifications on almost every aspect.

Jan 1, 2005

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By L. Bichler

Lightweight magnesium alloys are gaining in popularity for applications in the automotive and aerospace industries, Their use, however, remains limited due to their relatively low strength and creep properties. Lost Foam Casting (LFC) is a new casting process and the strength of foam cast magnesium alloys has not been investigated in great detail thus far, In this research, magnesium alloy AZ91 E and three new alloys were cast by the LFC process to study the effect of varying aluminum and manganese content on the alloy's tensile properties, The study reveals, that the tensile strength of the magnesium alloy is closely related to the relative amount of aluminum in the system. Formation of ß-Mg17Al12 phase was seen to significantly affect the yield strength and ductility of the alloy, Furthermore, formation of manganese intermetallic compounds was seen to effectively increase yield strength of the base alloy, Individual alloy morphologies were analyzed via optical and SEM techniques.

Jan 1, 2004

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007

By R. H. McMillan

A classification of important uranium deposits which utilizes both genetic and descriptive criteria is presented. The dual aspect is useful because, while the non-genetic nomenclature for the different deposit types is amenable to various interpretations, the critical characteristics of each deposit type can be analyzed to clarify various genetic points. Although the classification is intended primarily for Canadian uranium deposits, most of the important deposit types known elsewhere can be accommodated.

Jan 1, 1978

By M. Bouchard et G. Martineau

In the Chibougamau area, a large portion of the glacially tranported boulders which were deposited at the surface were later partly remobilized by the waters of Glacial Lake Ojibway. In the dispersal studies of these boulders, it is sometimes difficult to discern the effect of this reworking process. In addition, depositional processes in the lake contributed material to the original block deposits through the formation of boulder lag by littoral wave action and through direct sedimentation in the form of deltaic deposits. In spite of these complicating factors, dispersal studies at carefully selected sites which were unaffected by the above processes make it possible to unravel the general patern of glacial dispersion. In this study, indicator lithologies of the Albanel and Chibougamau formations were used. They give a coherent image of dispersal throughout the area showing transport toward the southwest. Considering the particular geological context of the region, and in view of the extensive mineral exploration studies which are being carried out, the results of this study are encouraging for the tracing of source areas of glacially transported mineralized boulders.

Jan 1, 1984

By J. W. Gregg, P. M. Dranchuk, D. L. Flock

"From preliminary investigations it has been observed that although evaporation losses may be estimated by comparing single values of certain physical properties of crude oils and their evaporation residues, such techniques possess little accuracy unless both the evaporation process and the variation of the property as a function of the process are completely known. The accuracy of estimation may be increased somewhat through the comparison of property mid-per-cent curves. Further increases in accuracy are possible if bottoms yield •curves rather than mid-percent curves are used. The use of both the mid-percent and bottoms yield curves however involves a prohibitive amount of effort in most cases. Examinations of distillation bottoms from Hempel type distillations carried to end points just short of the cracking point have indicated that these bottoms are not appreciably affected by the evaporation process. It was further observed that bottoms of identical API gravity, obtained from a crude oil and its evaporation residues behave as if they were pure components which were unaffected by evaporation. Based on these observations Hempel distillation bottoms of equal API gravity were obtained for a crude oil and its various evaporation residues from API gravity bottoms yield curves. The volume percent of these bottoms in the crude oil and its residues were used to calculate the evaporation losses suffered by the crude in order to yield the various residues. The results indicate that, although further refinements in technique are required, it is possible to calculate evaporation losses with an accept-able degree of accuracy through the use of this method."

Jan 1, 1960

RÉSUMÉ L’estimation la plus précise possible des coûts de minage est d’extrême importance pour les études de préfaisabilité afin de diminuer les risques financiers des projets miniers. Les méthodologies existantes d’évaluation des coûts de minage ne permettent pas de les évaluer avec des marges d’erreur acceptables tout au long de l’évolution des projets miniers. Elles visent à évaluer les coûts unitaires de minage des études préliminaires de faisabilité, pour les principales méthodes d’exploitation, en prenant pour l’hypothèse que ces coûts dépendent principalement du taux d’extraction journalière. Si cette hypothèse peut être justifiée pour l’évaluation du coût d’opération, elle est fort discutable pour l’évaluation des coûts de minage. Pour démontrer que cette hypothèse est inadéquate nous avons analysé la méthode d’exploitation la plus populaire sur le continent nord-américain c’est à dire celle par chambres vides avec retrait horizontal (Hr – Horizontal retreat), ou « Longhole » et celle avec retrait vertical (VCr - Vertical Crater retreat). Il ressort de cette analyse que les coûts unitaires de minage dépendent principalement des conditions géotechniques du massif rocheux et de la largeur du gisement et non pas du taux d’extraction journalière du minerai.

Jan 1, 2010

By H. A. Kramer

The Flin Flon mine is at present hoisting 5,000 tons of ore daily. In 1943, a peak production of 6,188 tons daily was maintained. Before discussing secondary blasting, it is felt that a short review of stoping procedure will be of value. A list of papers dealing with various phases of the mining operation is appended. Stoping Practice Stopes vary in width from 30 to 150 feet, in length from 200 to 450 feet, and in height from 200 to 500 feet. A typical stope would be 300 feet long, 300 feet high, and 90 feet wide. The dip of the orebodies varies from 60° to vertical, with an average of 82°. The ore is heavy, having a specific gravity of 4. Both sub-level benching and radial drilling are practised. Blast-hole diamond drills are responsible for 85 per cent of the total production. Two sizes of hole are drilled at present, 11 7 6 -inch and 1%-inch. For bench drilling, the burden on the 1 7/16-inch hole is six feet, with holes on 8-foot staggered centres; in radial drilling, the burden is six feet, with nine feet between the toes. The burden on the l 5/8-inch hole is eight feet with holes on 11-foot centres, or 13 feet on the toe of fanned holes. Holes are blasted with two No. 8 instantaneous electric caps per hole, using 403 Polar Forcite. A powder charge of 0.15 pounds per ton is used, with a tonnage factor of 5 and 6.4 per foot drilled for the two sizes. Two rows of holes are blasted together. Fragmentation is satisfactory with the above drilling pattern and powder charge. However, some overbreak and fall-off locally results in oversize material. It is estimated that, after primary breaking, 75 per cent of the ore will pass through the grizzly openings and 15 per cent will pass the draw points, leaving 10 per cent that must be broken further to pass the draw points.

Jan 1, 1946

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By Z. B. Karshigina, Ye. G. Bochevskaya, E. A. Sargelova, Z. S. Abisheva

At the present time of depletion of reserves of high grade rare earth deposits, it has become necessary to involve low grade raw materials in the production. Among the rare-earth deposits in Kazakhstan, the most advanced one is Kundybai. The mineralogical composition of ore is represented by the minerals: a-quartz SiO2, kaolinite Al2(Si2O5)(OH)4, muscovite KAl2(AlSi3)O10(OH, F)2, albite Na(AlSi3O8), rutile TiO2, and hematite Fe2O3. It contains: 59.1–68.5% SiO2, 19.1–28.4% Al2O3, 7.2–10.3% Fe2O3, 0.51–0.84% TiO2, 0.10–2.32% CaO, 0.39–2.10% MgO, and some other elements. Rare earths are located in the clay part (kaolinite, goethite) in the ion-adsorbing form, and they are represented by the main ore mineral churchite - YPO4·2H2O. In the ore the amount of rare-earth elements (total REEs) varies from 210 to 600 ppm. Elements of the cerium group predominate (La, Nd, Ce, Sm, Pr) and the yttrium group is represented by Y, Gd and Dy. Extremely thin intergrowth and accumulation of REEs in clay minerals cause difficulties in their recovery using flotation and gravitation beneficiating methods. The purpose of this work is the development of an extraction method for the main mineral components of ore with transfer of the total REEs into the solution with high extractive efficiency. Results of the experimental work into high-temperature processing (hereinafter referred to as sulphatization) of ore by sulphuric acid with subsequent dual-mode water leaching of the sulphate product (sinter) are presented in this manuscript. The influence on the ore sulphatization process of some physical and chemical parameters: liquid-to-solid (L/S) ratio (0.36–0.86 cm3/g), temperature (100 – 500°?), concentration of sulphuric acid (3.0–18.62 mol/L) and duration (0.5–2.5 h) was studied. Optimal technological parameters of the process were determined to be: L/S ratio 0.36–0.46 cm3/g; temperature 500°?; concentration of H2SO4 9.0 mol/L; soaking time 1.5 h. Under these conditions it is possible to obtain extractions of ~ 85% REE, as well as 58% aluminium and 10% iron. XRD and IR-spectroscopy analyses were used to determine the material constitution of sulphated cakes obtained under optimal conditions. It was found that the primary minerals are quartz and muscovite; however different sodium aluminium silicates and albite minerals are present as well. In the future, it is proposed that the leach residue cakes are processed into precipitated silica (“white soot”).

Jan 1, 2016

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By F. -Z. Ji, G. A. Irons, M. Barati, K. Coley

The use of oxygen in electric arc furnace steelmaking is tied to the use of fossil fuels, and slag foaming. The current work examines the kinetics of carbon injection into EAF slags especially the saturation injection rate and available reaction area in the slag foam. Based on individual rate data and experimental gasification rates of carbon in the slags, the available reaction surface area in the gas bubbles was found to be around 1900¬4700 cm2.kg-slg-1 for carbon injection into EAF like slags at appropriate injection rates and steel making temperatures. The ratio of number of bubbles to number of particles is 1 to 17 and the weights of carbon per unit reaction area are 0.001-0.008 gC-cm-2. Using the relationship between active reaction area and x supplied in this study, the gasification rates of carbon in slags can be estimated with gas-slag interfacial reaction rates.

Jan 1, 2004

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007