Search Documents

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007

By H. W. Smith, R. D. Fournier

This paper presents the results of an investigation of a full-scale rod mill. Appropriate numerical techniques are developed for the experimental determination of the parameters of a dynamic mathematical model from steady state data. The results confirm that this full-scale rod mill behaves similarly to laboratory-scale ball mills for which results have previously been obtained. It is noted, however, that although the model presented is adequate for predicting over-all particle size distributions, the size distributions of individual components of a multicomponent ore cannot be predicted.

Jan 1, 1972

By C. A. Y. Shephard, H. L. Brusset

Pressure maintenance by water flooding in the Pembina Field made consideration of wet crude dehydration and disposal of the produced water mandatory. Crude dehydration, the treatment and disposal of produced water, as well as the sale of gas and crude oil were expected to be handled more efficiently at one central point than at several conventional batteries. This plan was effected by routing the produced fluids to the central station by way of several well testing batteries referred to as satellites. To realize the full efficiency inherent in such consolidation the entire system was made self-regulating. Programming ensures the testing and proper routing of all products to their destination. Forty producing wells have been self-operated during the winter 1959 -1960 with gratifying results.

Jan 1, 1960

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By W. Beres, M. Bielawski

Recent research on the development of erosion resistant coatings has been directed to the finite element modelling of the behavior of coating and substrate, and their interface under the impact of eroding particles. The approach presented in this paper is based on advanced computer simulation techniques using ABAQUS/Explicit to investigate stress and strain at the surface and at the coating/substrate interface of multilayer coatings under single particle impact. It was found previously that solid particle erosion mechanisms are predominantly governed by the kinetic energy of the impacting particles. However, recent modelling efforts revealed that effects of various material models could be also significant. Therefore, different material models representing relevant coating and substrate properties were investigated and the effects of these models on the coating/substrate response were studied. Particularly, differences between elastic, elastic-plastic and brittle cracking model responses were assessed.

Jan 1, 2006

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By David Sanscartier, Elizaveta Petelina, Alexey Klyashtorin

This paper provides an overview of the radiological risk mitigation approach applied by the Saskatchewan Research Council (SRC) for the remediation of 35 legacy uranium mine sites in northern Saskatchewan where uranium exploration and extraction took place in the 1950–60s. Mining activities resulted in an irregular increase of the gamma radiation dose rate (up to 18 μSv/h). The radiological objectives for the sites include a gamma dose rate at a spot (<2.5 μSv/h above local background), and the dose rate averaged over a hectare (<1 μSv/h above local background). These objectives are generally achievable at the impacted sites through the installation of shielding soil cover. This method may be impractical for site areas with rough terrain (e.g., steep slopes) and/or difficult access. A risk assessment approach is applied to determine if these areas can be safely left uncovered or if additional mitigation measures should be implemented. The risk assessment approach is based on two factors: (i) the ambient radiation dose rates collected through gamma surveys, and (ii) actual land use data collected through various surveys of activities of local community members at the sites. Exposure scenarios based on four land uses are applied to estimate a potential annual dose load for members of the public. The estimated doses are compared with the criterion of 0.3 mSv/a recommended by the Canadian Guidelines for the Management of Naturally Occurring Radioactive Materials (NORM). If the criteria are not satisfied, a mitigation plan is developed, and post-remediation gamma levels are modelled using GIS tools to evaluate the performance of the proposed mitigations. The proposed approach allows the team to optimize resources for the site remediation so that public exposure to NORM are as low as reasonably achievable after remediation.

Jan 1, 2020

By D. P. Bishop, G. J. Kipouros, R. L. Hexemer Jr., I. W. Donaldson, W. F. Caley

Aluminum powder metallurgy (APM) is an advanced metal forming technology frequently employed to fabricate complex structural components in a near-net-shape fashion. Exhibiting nearly 100% material utilization, APM continues to rise in popularity. Recent research initiatives in this field have emphasized the development and processing of advanced 2xxx and 7xxx series alloys. In particular, APM equivalents to wrought 7075 and 2024 have been sought. An overview of work completed in this area is presented. Included are data on the various production stages (powder compaction, sintering, forging, and heat treatment) as well as the microstructure and mechanical properties of the finished products.

Jan 1, 2010

By John Redstone, André R. Laplante

"Le rebroyage des concentrés d&apos;hématite en usine (Sidbec-Normines, Port-Cartier) et en laboratoire a été modélisé selon le modèle de Reid (1965).L&apos;effet du pourcentage solide sur la cinétique de broyage a été étudié en usine. La fonction de sélection corrigée (pour tenir compte de l&apos;effet du pourcentage solide sur le temps de rétention) augmente lorsque le pourcentage solide augmente de 80 à 84 pourcent. Cette amélioration est contrebalancée par une augmentation de la quantité de pulpe court-circuitée, à des pourcentages solides supérieurs a 81%. La densité optimum de broyage se situe à 84 pourcent.Comme alternative au mode d&apos;opération actuel, l&apos;assemblage des broyeurs en série plutôt qu&apos;en parallèle a également été simulée. Le moins 44 µm passe alors de 68.1 à 72.5 pourcent, ce qui correspond à une capacité supplémentaire de 32 tonnes à l&apos;heure par broyeur. Ces résultats doivent toutefois être interprétés avec prudence, car la cinétique de broyage n&apos;est généralement pas linéaire lorsque le taux d&apos;alimentation est plus que doublé.IntroductionL&apos;usine de bouletage de Sidbec-Normines Inc. a été décrite par Morimoto (1977), Lévesque et al. (1979) et Pabst (1979). La section de broyage des concentrés contient six broyeurs à boulets en parallèle et en circuit ouvert, d&apos;un diamètre de 5. 18 mètres et de 10.36 mètres de longueur. Ils contiennent chacun environ 350 tonnes de boulets d&apos;acier forgé de 3.8 cm de diamètre. Le concentré est broyé de 10 pourcent moins 150 µm (100 mailles) à 65-68 pourcent moins 44 µm (325 mailles), à un pourcentage solide de 78 à 80 pourcent. Cette fragmentation poussée exige une consommation d&apos;énergie de 32 kWh/tonne. Cette énergie est surtout libérée sous forme de chaleur, la pulpe étant déchargée a une température de 68-72° C. II en résulte un milieu de broyage corrosif, et une consommation de boulets élevée, de 3.4 à 4.0 kg / tonne broyée."

Jan 1, 1983

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010

By K. A. Natarajan, M. N. Chandraprabha

Selective separation of minerals from complex sulphide ores is a challenging task and it is often difficult to get commercially acceptable individual concentrates by conventional selective flotation using inorganic collector reagents. Microbially-induced mineral beneficiation has proved to be more effective, economically viable and an environmentally benign process for the effective separation of various minerals. Applications of microbially-induced mineral beneficiation are demonstrated in this paper with respect to beneficiation of complex multimetal sulfides. The role of adapted microorganisms and bioreagents in the beneficiation of complex sulphide minerals are also illustrated.

Jan 1, 2009

By W. de Klerk, M. B. Thorpe

Golden Star Resources Bogoso operates in Ghana’s Western Region. The gold recovery plant includes; a flotation circuit producing a concentrate for the BIOX® process that oxidizes sulphides before a CIL circuit; and a dedicated CIL circuit. BIOX® uses bacteria, therefore water from the BIOX® and CIL plants remained separated; CN water could not be introduced into the flotation / BIOX® circuit. The operation built a process water inventory with high TDS and installed a process water treatment plant (PWTP). Water was released in compliance the permits but containing some thiocyanate. The PWTP brine was returned to the TSF, further exacerbating the TDS. The operation experienced a drought removing the traditional water sources; the team evaluated the options to maintain production - various water streams were laboratory tested provided options for water use. The paper presents the story (treatment chemistry and process chemistry) of continued operations by treating stored water and PWTP discharge water with peroxide; brine usage within the CIL circuit, which increased gold recovery (laboratory testing) and reduced the TDS. Water flows were further modified to include hydraulic tailings re-mining to a CIL circuits. Details of the recovery, basic chemistry and costs savings are provided.

Jan 1, 2014

By A. J. Makoka, B. C. Qi

Reliable monitoring of corrosion is vitally important in the combat against corrosion and over the last two decades the interpretation of electrochemical noise has received considerable attention as a means to discriminate between different types of corrosion. To this end, many different analytical methods have been proposed, such as power spectral density analysis and analysis via various other stochastic criteria. However, although many corrosion systems are nonlinear and therefore not readily interpretable by the abovementioned analytical approaches, few studies in the analysis of electrochemical noise to date have exploited advances made in the analysis of nonlinear systems. In this paper, the use of phase space methods to analyze and detect change in corrosion systems via electrochemical noise is considered. In particular, the electrochemical noise data are used to reconstruct trajectories in the so-called phase space of the system and changes in the topology of these trajectories or attractors as represented by correlation dimension curves are consequently interpreted as an indication of change in the dynamics of the system.

Jan 1, 2005

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By Arthur Grounds

Historical In the course of a paper which is necessarily limited in length, such as the present one, it is obviously impossible to describe in detail the history, development, and present position of coal preparation in Western Europe. Great Britain has been blessed with large deposits of excellent coal of nearly every type, ranging from the high-grade anthracites of South Wales, which are characterised by their very low ash and volatile con-tents, to the superb coking coals of South Wales and Durham -probably the finest in the world -with their low ash and sulphur contents, the latter constituent often well be-low l per cent. Gas coals abound in Lancashire and Yorkshire, while coals from the East Midlands, Northumberland, and Scotland are excellent for steam-raising and other industrial purposes. The excellent quality of these various coals has, in years gone by, ensured ready .sales abroad and it is not surprising, therefore; that methods of coal preparation were largely developed on the Continent in an endeavour to upgrade the inferior fuels found there, so that the prepared product could compete with British coals on the European market.

Jan 1, 1951

By J. Shahabpour

"Abstract - Breccias with angular and rounded clasts of a late-mineralization, ""barren"" hornblende porphyry dike set within a comminuted matrix consisting of rock fragments and quartz, cemented by quartz and K-feldspar of hydrothermal origin is observed in diamond drill cores from the Sar Cheshmeh porphyry copper deposit. Studies of age relationship between vein types, phyllic-altered clasts and the breccia groundmass suggest that the brecciation is a late event. The breccia clasts record evidence of hydrothermal reaction between the clasts and fluids responsible for the brecciation.Formation of bornite, in the breccia clasts of the originally barren hornblende porphyry dike, and in the breccia matrix, along with the scarcity of bornite in the Sar Cheshmeh deposit itself suggest involvement of fluids which are later and of different composition from the fluids responsible for the known mineralization at Sar Cheshmeh. These later fluids may be related to a later plutonic event and suggest the possibility of a later, and concealed deposit."

Jan 1, 1994

By Wynne Potter

"On the west coast of Cape Breton Island four coal basins have been identified, varying in age and extending from Port Hood northeasterly to Chimney Corner. Those of Chimney Corner - St. Rose in the north and Port Hood in the south belong to the Pennsylvanian Riversdale Group while lying between them are the coal basins of Mabou and Inverness belonging to the younger Pictou Group. Almost all of the coal basins are submarine and coal mining was carried out on all basins at various times. The seams in all basins dip steeply seaward at angles from 10 to 20 degrees but were found to flatten seaward. The coal is ranked as a high volatile C bituminous coal. Ash and sulphur contents are high compared with Sydney coal and the coal has a tendency to spontaneous combustion when stored in large quantities.Of the four basins, the most significant is that of Mabou. At Mabou recent seismic and drilling investigations have indicated that although a sizable reserve of coal may be found offshore the structural problems, particularly faults, and the poor quality of the coal encountered will make it a resource of the future, if at all. Inferred resources have been calculated at 150 million tonnes in four seams over a 10 km2 area and extending 3 km from shore. The quality of the Mabou coals varies with ash, ranging from 5 to 25 per cent and sulphur up to 6 per cent. Calorific value ranges from 25.3 Mj I kg to 31. 7 Mj I kg. The Port Hood and St. Rose -Chimney Corner fields (Fig. 1) contain 16 million and 3 million tonnes respectively, but the Inverness basin is considered to have been depleted. The active mine in this area is the Evans Mine at St. Rose that is currently producing between 30 -50,000 tonnes a year from proven reserves of approximately 3 million tonnes."

Jan 1, 1985

By M. R. Hegge

The Jabiluka One and Two uranium deposits occur in Lower Proterozoic metasediments of the Cahill Formation, which is part of the Pine Creek Geosyncline in the East Alligator River area, Nothern Territory. The Jabiluka One deposit coincides with a "window" through unconformably overlying Middle Proterozoic sandstone of the Kombolgie Formation; Jabiluka Two is completely covered by that sandstone. The observed part of the Cahill Formation exhibits four horizons which are favourable hosts for uranium mineralization. These have been folded into an east-southeast-striking, gently plunging, open asymmetric syncline-anticline structure. The host rocks are mainly chlorite and/or graphite schists and their brecciated equivalents which have undergone initial regional prograde metamorphism to the amphibolite facies, then retrograde metamorphism to the greenschist facies. Mineralization consists of pitchblende, mainly filling open spaces and to a lesser extent in disseminated form. Chlorite, pyrite and quartz are commonly associated with the uranium mineralization. A portion of the Jabiluka Two deposit contains economic concentrations of gold. Structural preparation with low-pressure conditions at these sites appears to be the most significant ore control. Genetic hypotheses favour initial deposition in Lower Proterozoic sediments, followed by remobilization during later orogenic events. The deposits bear a marked similarity to some pitchblende deposits in central Canada.

Jan 1, 1977

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014