Search Documents

By A. R. Harrington

BEFORE discussing some of the technical aspects of the steam generating plants of Nova Scotia Light and Power Company, Limited, it might be of interest to go back through history and see the development of steam generation in this public utility. Back around 1902 Nova Scotia Light and Power Company, Limited, had three slide-valve engines in-stalled at its Water Street, Halifax, generating station for a total capacity of 1,800 kilowatts. The plant remained at about this size until 1910 and in 1911 a 2,000 kilowatt steam turbine was installed to raise the total capacity of the plant to 3,800 kilowatts. In 1916, a 3,000 kilowatt turbine was installed and one of the slide-valve engines was removed to make a total plant capacity of 6,200 kilowatts. The total demand in the Company's service 8rea was at that time 4,000 kilo-watts.

Jan 1, 1958

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential ?nanciers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory under-ground development is required to de?ne measured resources. The de?nition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and speci?c gravity are common. Veins may be composite, with ore-grade mineralization restricted to a speci?c structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and re?ect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature;(2) estimation of tonnage and grade, and (3) the presentation of this information using a classi?cation that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the dif?culties in applying geo-statistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or under-estimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for pro?t and/or greater economies of scale. De?nition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than ?nding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By Simon C. Dominy, Alwyn E. Annels, Paul Wheeler, Suzanne P. Barr, G. Simon Camm

Abstract-Narrow veins are an important world-wide source of silver, tin, uranium and particularly gold. To potential financiers, this style of mineralization is viewed as high risk because of the often relatively small resource involved and high cost of estimation. In many cases diamond core drilling will not enable resource estimation beyond the inferred and indicated categories. Exploratory underground development is required to define measured resources. The definition of geological and grade continuity are major factors in narrow vein assessment. A measured resource must be based on strong geological and grade continuities. Narrow veins, generally less than 3 m wide, are complex geological phenomena, which commonly display unpredictable geometry and grade distribution. Variations in structural continuity, dip, strike, width, mineralogy and specific gravity are common. Veins may be composite, with ore-grade mineralization restricted to a specific structural domain. Branches, intersections and braided zones are common features. Potentially high-grade zones are often localized within ore shoots, which are surrounded by barren/low-grade regions. Resources must be determined as closely as possible to reality and reflect the distribution of the commodity in the rock. Estimation has three main requirements: (1) geological study to determine orebody nature; (2) estimation of tonnage and grade, and (3) the presentation of this information using a classification that is clear, unambiguous and bankable. Estimation methods employed are either classical or geostatistical; however, classical methods are often used because of the difficulties in applying geostatistics. Grades generally show a strong positively skewed distribution testifying the presence of high-grade values. Problems exist in the applicability of cutting outlier values risking over- or underestimation of grade. It is generally believed that where resource estimates are in error, poor geological control is usually the cause. Overestimation can lead to the closure of a mine through lost revenue and capital. An understated estimate can result in an opportunity missed for profit and/or greater economies of scale. Definition of reserves involves the consideration of economic and engineering data, to decide which part of the resource is economically mineable. Geology plays a similarly important role at this stage in the assessment of likely mining method, dilution, recovery etc. Throughout resource/reserve estimation, it is crucial that the amount and quality of the data and the geologist’s experience are relevant. The impact of geological understanding on estimation is often undervalued or assumed to be of lesser importance than finding grades and tonnages. This paper discusses the geology of narrow vein deposits and the importance of geology in their evaluation.

Jan 1, 1997

By M. S. King

"A simple method is proposed for determining the long-term deformation behaviour of evaporites. The theory developed can be tested by measuring the change in diameter as a function of time of a vertical mine shaft opposite evaporite strata. Ultimate shaft closures predicted by the theory agree well with those calculated with the very much more complex theory of Serata (1968), provided that sufficiently high octahedral shear strengths are used in the former.An analysis of measurements made in an isolated opening in a Saskatchewan potash mine shows that the octahedral shear strength of the surrounding potash and halite was approximately 500 psi several years after the opening was mined. This value is less than that deter-mined experimentally for halite by Serata. The same data indicate, furthermore, that the in-situ octahedral shear strength is decreasing slowly with time.The current controversy regarding the actual deformation of evaporites will only be resolved by the cooperation of potash producing companies in releasing data on the long-term deformation of their mine shafts."

Jan 1, 1971

By J. C. Nicholson

The "V" system was first introduced by the West Virginia Coal & Coke Company at their No. 9 mine, Norton. Norton is a small mining village on the B. & 0. railway, about seven miles from the town of Elkins. This year, accompanied by G. D. MacDougall, I visited this mine to obtain first-hand information regarding this modem system and to determine its adaptability to conditions in Nova Scotia. The following is a brief account of my observations. The seam that is being worked is known as the Lower Kittaning, which, at this point, has an average thickness of 7 feet. This includes a band of hard clay varying in thickness from 8 to 14 inches, which occurs about 2 feet from the pavement, also 8 inches of inferior coal at the roof. The latter is not recovered, which leaves to be mined about 5 1/2 feet of clean coal. The roof is slate and shale for the first 30 feet, followed by 40 to 60 feet of sandstone; the total cover is from 80 to 250 feet thick. The seam lies very flat, with a dip of only 2 per cent., and, as the dip is toward the main entrance, it' is in favor of the load, also providing natural drainage for any water the mine makes. As the mine is not gassy, and there is no water to be pumped out, one can understand that mining conditions are practically ideal.

Jan 1, 1924

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By C. Blawert

The corrosion properties of the skin and the bulk of semi-solid processed and high pressure die cast AZ91 alloy were studied in 5% NaCI solution by (a) analysing the corrosion morphology, (b) measuring electrochemical polarization curves, (c) performing electrochemical impedance spectroscopic measurements, and (d) immersion tests at constant pH-values. Using XRD, LM, SEM and EDX to evaluate the microstructure of skin and bulk specimens, the corrosion results were related to the microstructures of the particular alloys. However, microstructure and corrosion performance were found to be similar for both production processes, and only slight but distinct differences were found. Generally, the skin corrosion properties are inferior to those of the bulk, with the exception of the high pressure die cast AZ91 alloy, where the finer microstructure of the skin layer exhibits a better performance as showed by impedance studies and confirmed in long term immersion tests.

Jan 1, 2004

By Donald P. MacKinnon

"This paper is a commentary on selected trends within the transportation industry.In general, innovations are taking place within all modes of transport (road, rail and water) serving the industrial minerals industry which will affect future distribution patterns, methods and costs. Significant technical innovations in the transportation of solids by• pipeline will also appear, perhaps in the near future, permitting the transport of specific commodities, including some industrial minerals. However, the timing and magnitude of the commercial exploitation of solids pipelines are heavily dictated by marketing factors and distribution system logistics, as well as by the innovations likely to take place within competitive modes of transport. Competitive technological developments will include increased ship capacities, improved bulk-handling facilities, larger and specialized bulk-handling rail equipment, unit trains, containerization, larger ""off-highway"" vehicles and greater inter-modal integration. Equally significant are some ""soft-ware"" techniques such as the growing interest in total distribution cost concepts. However, the impact of the developments will not be spread uniformly over all Canadian industrial minerals."

Jan 1, 1967

By R. Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as an inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1995; Walsh and Rao, 1986; Walsh and Kelly, 1992). In November, 1993, the author inspected the grinding circuit at La Mine Doyon in Rouyn-Noranda, Quebec and made recommendations to recover coarse gold and to eliminate gold traps from the circuit. In 1995, the author salted mineral processing circuits with radioactive gold particles. The gamma and X-ray radiation from gold’s nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment using scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps and improving security.Nuclear TracersWhen particles of gold are placed in a nuclear reactor, some of the gold atoms (Au197) absorb another neutron in their nucleus to form gold’s radioactive isotope (Au198). In the process of radioactive decay, this isotope emits high energy gamma rays and X-rays which are easily detected (even through steel) with scintillometers.Radioactive gold (Au198) has a very short halflife of 2.7 days. At the relatively low activity levels used for tracing, the particles remain detectable with a small hand-held scintillometer for about 10 to 14 days. After 14 days the irradiated gold is close to background levels and within two months it is essentially non-radioactive. The radiation has no effect on the recovery characteristics of the gold particles. The gold radiotracers are very safe due to their very low level of radiation, short half-life, and their inherent physical and chemical stability. However, the use and possession of even mildly irradiated gold is strictly licensed and regulated."

Jan 1, 1997

By Geoffrey Gilbert

Rossland is in the West Kootenay district; 5 miles north of the International boundary and 4 miles west of Columbia River at Trail. The first claim in the district was located in 1887; but there was little activity until 1890; when the showings that later became important were staked and development began. Production increased rapidly from 1; 800 tons in 1894 to a peak of 360; 000 tons in 1903; and averaged 286; 000 tons for the next 13 years. It declined sharply in 1917; and continued to decline until the closing of the main mines in 1928. Between 1933 and 1941 leasers mined a further 137; 000 tons. Total output has been about 6; 200; 000 tons; with average recovery of 0.47 oz. gold; 0.6 oz. silver; and 1 per cent copper. The total value was $82; 500; 000; of which aboµt three-quarters was in gold; the camp still leads the province in total gold produced. Ninety-eight per cent of the tonnage came from a small compact area worked by four inter-connected mines : the Le Roi (39 per cent); Centre Star (25 per cent); War Eagle (24 per cent); and Josie (10 per cent); all now owned by the Consolidated Mining and Smdting Company of Canada; Limited.

Jan 1, 1954

"A numerical procedure based on Smoothed Particle Hydrodynamics (SPH) is developed for rock blasting phenomena involving multiple intersecting joints. In this procedure, an elasto-plastic damage constitutive model has been applied in the framework of SPH to simulate yielding response of the surrounding rock medium. In this paper, a square shape rock medium with centrally located emulsion explosive in a borehole is numerically blasted with and without the presence of two diagonal rock joints. The model is simulated by assuming all four sides of the rock medium as free surfaces. The paper elaborates the propagation of stress wave, expansion dynamics of gaseous products, and development of fracture, fragmentation of the medium and dissipation of energy due to damage.INTRODUCTIONDamage prediction of rock mass and its mean fragmentation size are of important to design blast parameters for a given explosive. Current blasting practice solely depends on empirical relationships between fragmentation sizes to those blast design parameters while mathematical descriptions of the physical laws governing the process of rock blasting are limited. A constitutive relationship based on properties of explosives and rock mass is of special interest because of its capabilities in describing the key features of rock fracture and fragmentation, resulting in understanding of the physical process involved in rock blasting. It is well known that blast-induced damage and fragmentation of rock mass occur due to detonation induced stress wave and product gas driven fracture propagation. Nevertheless, the fundamental mechanism of the failure process and the behavior of rock characteristics under these two different loading are not well understood in many cases, which are closely related to growth of fractures and interaction of cracks under different loading conditions.Continuum damage mechanics is considered to be appropriate to describe the failure process under such high-amplitude stress wave. Based on this approach, several theoretical models have been developed to analyze the dynamic damage of brittle material such as rock and concrete with microstructure (Chen, 1999; Taylor et al., 1986; Wu et al., 2004; Yazdchi et al., 1996). These models are mostly based on the theory of damage mechanics or fracture mechanics with some statistical treatment to incorporate random distribution of microcracks. In the application of fracture mechanics theory, sometimes it is difficult to estimate the micromechanical parameters such as crack density and fracture toughness in different modes. In this study, damage in rock material is evaluated according to the earlier model developed by Grady and Kipp (1980), which is a fracture model coupled with a material description for stress wave propagation to predict quantitatively fracture and fragmentation under explosive loading conditions."

Jan 1, 2015

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By D. G. Eskin

"It is well known that it takes some time for the solid phase to completely dissolve upon melting, especially inside the defects of insoluble particles, e.g. oxides. Until then the oxides remain active solidification substrates in the case of subsequent solidification. It is also known that ultrasonic melt treatment causes grain refinement through activation and dispersion of solidification substrates (one of the mechanisms) and also accelerates the dissolution of solid metal in the melt. In this study we combine these effects and demonstrate that the introduction of an alloy rod into the matrix melt of the same composition results in significant grain refinement, this effect being increased by the ultrasonic vibration of the rod. The achieved grain size is comparable to that obtained by a standard Al–Ti–B grain refiner. All samples were cast using a standard TP-1 mould to enable correct comparison. The effect of the temperature range of the rod introduction, as well as the effect of ultrasonic vibrations are discussed.INTRODUCTION The fact that by introducing solid metal into the melt one can achieve structure refinement is rather well known. As early as in the 1930s–1950s a series of papers and patents have been published, showing the benefits for grain refinement when dissolving solid metal in the melt before solidification (Danilov and Neimark, 1938; Scheil, 1956). Later on this way of structure refinement was developed further and dubbed “suspension casting” or introduction of “internal chills” (Madyanov, 1969; Zatulovsky, 1981). The solid metal was added in a form of cut wire, cut sheet, or powder, with the resulting grain refining, elimination of columnar grain structure in ingots and castings of steel, copper and aluminium alloys. The underlying mechanisms have been suggested as (1) rapid cooling of the melt due to the latent heat consumption upon melting of the solid metal with the resultant melt undercooling and (2) introduction of many solidification substrates in the form of crystal fragments and active non-metallic inclusions (Danilov & Neimark, 1938; Balandin, 1973). A number of patents have been filed where either the same solid alloy or a master alloy with additions (e.g. Ti for Al alloy) is introduced in the amounts up to 50% (typically less than 10%) into the melt close to the liquidus temperature (Schmidt, 1966; Talbot & Soller, 1973, Krupp, 1974; Bondarev, 1979). The main reason that this technique is not widely used in industry is the possible incomplete dissolution of the solid parts introduced into the melt with ensuing inhomogeneous as-cast structure and potential defects. Also the selection of the temperature range where the technology works the best is not clear."

Jan 1, 2018

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By Warwick Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions as it applies to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance as to the minimum size and/or in-situ value per tonne requirements of targets being sought in order to ensure economic success and probable exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the mine site by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Apr 1, 2005

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963