Search Documents

By K. K. Panthi, P. K. Shrestha

"Displacement of rock mass around a tunnel opening varies according to the rock mass properties, insitu stress conditions and applied support in the tunnel. Such displacement is also altered by presence of bands of rock mass that differ in properties. This paper focuses on the deformation behavior of rock mass around tunnel openings at four tunnel sections in Kaligandaki headrace tunnel where extensive instrumentation was done. Based on the actually measured tunnel displacement records and actually measured support pressure; back analysis has been done to estimate rock mass properties and insitu stresses. Numerical analysis has been done to analyze and assess the deformation behavior of the rock mass around the tunnel sections.INTRODUCTION Instrumentation and monitoring of tunnel convergences have significant importance in evaluation of tunnel stability. One of the key aspects of monitored data is that early convergences can be used in estimation of long term convergence. In addition, these data can also be used in evaluation of rock mass parameters and in-situ stresses around the tunnel. Convergence around a tunnel periphery may vary according to rock mass quality. Presence of bands of different rock mass may hinder the displacement pattern in the tunnel. Particularly, displacement characteristic of tunnel periphery in schistose, foliated and deformed rock mass is altered by presence of bands of comparatively stronger rock mass, e.g., quartz veins or presence of shear seams or faults. Similar observations were also recorded in monitored tunnel sections in Kaligandaki headrace tunnel, located in the Nepal Himalayas. Extensive monitoring was done by installing multiple point borehole extensometers (MPBX) at three different locations of the tunnel periphery at four different tunnel sections. In addition, convergence measurements by tape extensometers and installation of pressure cells to record support pressures were also carried out at each of the tunnel sections. Observations showed that the tunnel convergences varied according to rock mass quality, in-situ stress and effective support pressure.Rock mass parameters and stresses have significant role in the extent of tunnel deformation, but these parameters are often unknown or difficult to predict. Back analysis based on actual tunnel displacement records and known support pressure is believed to be an important method in such endeavor. This paper performs back analysis to evaluate rock mass parameters and discusses correlation of rock mass behavior with tunnel deformation and applied support. For this purpose, the rock mass parameters are estimated from actual tunnel displacement records, mapped rock mass quality records and laboratory tested data. Then, numerical modelling is conducted to correlate post peak behavior of the rock mass with actual tunnel displacement."

Jan 1, 2015

Risk management has taken on renewed vigor since the economic crisis of the late 2000s. The resources of governments, individuals, and corporations are being stretched to a point where only the most promising projects move forward. Risk management is a crucial part of the decision making process, yet it remains a broad term that includes disciplines from engineering to finance. A collaborative effort will be necessary to ensure that the most auspicious and appropriate projects are the ones moving forward. Risk management can be quantified to an extent by comparing the likelihood of an instance with the result of consequence of the instance occurring. In this manner it is possible to assign risk factors to instances and ultimately, begin to associate monetary value to the instance. Carbon sequestration is an emerging field that has a number of unique challenges. Risk management and mitigation must be an integral part of the overall picture. This begins with the planning and design phase, continues through implementation and production, site closure, and does not cease until termination of liability. The ability of carbon sequestration projects to successfully assess, mitigate, and recover from leaks will be a decisive characteristic of overall success. The costs of mitigation and failure will need to be analyzed on a test level, but will still need to be reliable enough to extrapolate to a commercial level operation. This paper will build a risk management profile based on case studies and field tests in Tennessee and Virginia. These tests are scheduled to commence in late 2013 and consist of small-scale injection tests in unconventional storage reservoirs with an emphasis on enhanced coalbed methane (ECBM) recovery and enhanced gas recovery. The ultimate goal will be to provide a clear and concise direction to move carbon sequestration from the test phase to commercial scale. While it is necessary from a risk management perspective to analyze all risk points, the scope of this paper will focus on pre-injection risk assessment for carbon dioxide (CO2) leakage potential. Despite the differences between the two tests, CBM compared to shale among other differences, a framework for analysis and mitigation can be developed pertaining to leakage risk. The probability of each type of failure will be assessed and analyzed, and plans to mitigate or reduce these risks will be reviewed.

Aug 1, 2013

"Developed by CRIRSCO, IRT is a document that draws on the best of the CRIRSCO-style reporting standards. These reporting standards are recognised and adopted world-wide for market-related reporting and financial investment.The IRT is not an international reporting code and does not supersede existing national reporting standards. Rather it is a guideline that encapsulates the content of these standards for the benefit of the international mining industry and its various stakeholders.The template is a 'living document' that is continuously updated and improved as new national laws, rules, codes and guidelines are created or amended.The International Template is advisory only and where national codes already exist, these will take precedence. The International Template is intended to assist those countries that either do not have a reporting code or whose code is outdated, to produce a new code consistent with international best practice. It also provides a consolidated version of national codes that reflects their compatible international components and may thus be used in comparisons with other international reporting systems. The word 'Template' is used advisedly to indicate that this document is a model for code development and does not in itself constitute a 'code' which implies that it has legal or other regulatory force.From this point forward, the Template includes words that imply a mandatory action, such as ""requires"", ""applies"", ""must"" etc. This is to enable the Template to be easily adopted by countries and organisations wishing to do so, and does not imply that the Template itself is a mandatory reporting standard.INTRODUCTION2 In this edition of the International Reporting Template (""The Template""), important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Template clauses using indented italics. They are intended to provide assistance and guidance to readers for interpreting the application of the clauses in the Template.Indented italics are also used for Appendix 1 — 'Generic Terms and Equivalents"", and Table 1 —'Check List of Assessment and Reporting Criteria' to make it clear that they are also part of the guidelines for the application of the Template.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that may be considered in addition to the Codes of Ethics or Practice normally applying to members of professional institutions."

Jan 1, 2003

By N. Aslin, G. Heferen, H. DeWaal

"Mount Isa Mines (MIM) acquired a reputation for the successful application of R&D to develop break-through technologies for the mining industry starting in the 1978’s through until the early 2000’s. The ISAPROCESSTM tank-house technology has been licensed to copper refineries throughout the world, and a significant per cent of the world’s copper is refined using this technology. Since development in the late 1980’s more than 20 ISASMELTTM copper and lead smelting furnaces are now installed in countries around the world. Jameson Cell flotation technology developed jointly by Mount Isa Mines and Professor Graeme Jameson is widely used in the Australian coal mining industry and increasingly in the base-metal and gold industry. The IsaMillTM’s developed at Mount Isa and McArthur River made it possible to develop the McArthur River and George Fisher orebodies and has been successfully implemented into base metal fine grinding applications around the world. The most recent commercialised innovation is the atmospheric leach Albion ProcessTM with its supersonic HyperSpargeTM gas sparger, is being adopted as a solution to the increasing complexity of orebodies. MIM’s contribution to the industry was significant given the size and the remote location of its operations with Townsville Copper Refineries more than 1350 km and Mount Isa 1800 km from the nearest state capital of Brisbane. This paper will briefly discuss the development of each of these technologies and why MIM – now owned by Glencore - was so successful innovating and developing such technologies over a period of nearly 40 years.INTRODUCTION Mount Isa is located in the Gulf Country region of Queensland about 1800 kilometers North West of Brisbane (see Figure 1). It came into existence because of the world class mineral deposits found in the area. In 1923 the orebody containing lead, zinc and silver was discovered by the miner John Campbell Miles. Mount Isa Mines Limited (MIM) was founded in 1924 to develop the minerals discovered by Miles, but production did not begin until May 1931. It paid its first dividend in 1947 after 16 years of troubled production. In 1954 the 1100 copper orebody was discovered and with rapidly rising reserves during the 1950’s and 1960’s led to the construction of new concentrators to treat lead/zinc/silver ores in 1966 (#2 concentrator) and copper ore’s in 1973 (#4 concentrator). The difficult nature of the Mount Isa lead-zinc orebodies has meant that the company had always needed to be at the forefront of mining technology. In the 1970’s through to the 1990’s, it became a world leader in developing new mining techniques and processing technologies as a response to declining metal prices and rising costs. Mount Isa has been smelting copper since 1953 and lead since the early 1930’s. Copper Refining at Mount Isa’s fully owned subsidiary of Copper Refineries Proprietary Limited (CRL) had commenced operations in 1959."

Jan 1, 2018

By George Meadows

Consultation and Accommodation Introductions Consultation -Best Practices The Role of Negotiations The HVC Experience Summary / Conclusions The Challenge Meeting legal and policy obligations to consult while adhering to project priorities, timelines and budgets Defining who needs to be consulted, by whom, and ?how much?? Accommodation ?who is responsible and what is the appropriate scope? Social License -establishing positive working relationships with First Nations involved in project review / approvals / implementation in a manner that advances the interests of all parties

May 1, 2010

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978

By J. F. Boux

"The study of the total utilization of fly ash has involved all of the known technology in the processing of this waste material into useful products. In addition, a complete knowledge of all the possible uses of fly ash and its products in the market area was probably the most important factor in evaluating the theory and practical feasibility of the total utilization of fly ash from a single large supplyLaboratory tests carried out on the separation of fly ash into different fractions were shown to improve its value and utilization. Four main fractions were studied: a fine pozzolanic low-carbon fraction; a coarse fraction for light-weight aggregate production by pelletizing and sintering; a high-iron fraction; and a carbon-rich fraction. The term ""beneficiation"" here refers to a process of separating fly ash into more useful components.Laboratory and pilot sinter strand tests were employed to optimize the sintering capability and the quality of the heat-hardened pellets through a study of the agglomeration cycle in four principal heat zones, under controlled conditions of air flow, temperature and atmosphere, and including the controlled sizing of pellets.The suitability of the heat-hardened pellets as light-weight aggregate was evaluated in test batches of concrete, which were compared with concrete containing commercial lightweight aggregate of established quality.A study of beneficiated fly ash pozzolan as a partial cementitious binder component in normal and high-temperature cured concrete was reported in a paper at the re-cent Second International Fly Ash Symposium.Samples of raw and beneficiated Lakeview ash were compared with samples of other established high-quality fly ash pozzolans. The evaluation indicated the usefulness of beneficiated Lakeview ash as a pozzolan. Economic studies indicated that to accomplish the primary objective of total utilization of any single source of fly ash (in this case. fly ash from the Lakeview Generating Station, producing approximately 400,000 tons per year), a broad knowledge of the technology of various mineral processes was essential.The design of the fly ash processing plant had to be based on the disposal of all the raw fly ash produced by the generating station. This is contrary to the normal design of a processing plant in which raw materials are supplied and produced according to product demand. The design, therefore, had to be of such flexibility as to pro-duce as wide a variety of products as possible, and the ability to market them had to be well researched and understood."

Jan 1, 1970

By G. Stafford Whitby

N ATURAL gas is found in several provinces of Canada, particularly Ontario, New Brunswick, and Alberta. The largest producer is Alberta, and there the most important field is the Turner Valley, where some low-gravity crude oil and naphtha are associated with the gas. Last year there was produced from the Turner Valley field an average of 3,462 barrels, or about 450 tons, of oil a day. The gas flow from the wells in this field bears such a high ratio to the oil which comes from them that, despite the enforcement of a measure of conservation, it amounted to the vast quantity of 6,000 tons a day, or more than 2,000,000 tons a year. Prior to the application of any conservation measures, the gas flow was at one time of the order of 12,000 tons a day. The heat content of one ton of the gas is almost equal to that of two tons of coal. A certain amount, say, 10 per cent," of the gas is used in Calgary and surrounding towns and in re-pressuring the Bow Island gas field, but the greater part of it goes to waste. What are the possibilities of making use of this waste gas, in whole or part? The possibilities of using it profitably as fuel for domestic and industrial purposes have undoubtedly been carefully considered by the Company which now distributes a part of the gas to cities and towns in Alberta. But the relative sparness of the population and the cost of pipe lines makes such possibilities strictly limited. There are, however, distinct possibilities of making use of at !east a part of the gas for the production of a variety of chemical products and of liquid motor fuel. The present paper is devoted to outlining some of these possibilities. About three-quarters (by weight) of the Turner Valley waste gas consists of methane, the lightest and, chemically speaking, the simplest of hydrocarbon gases. The remaining quarter consists of heavier hydrocarbon gases-ethane, propane, and butane. Formerly, naphtha was separated from the well gas by a simple process of self-refrigeration. The gas coming from the wells at a pressure of, say, 1,200 to 1,800 lb., was passed through simple cylindrical vessels fitted with baffles and known as 'separators'. The pressure was allowed to drop to, say, 300 lb. in the separators, and the cooling effect secured by this expansion brought about separation of the naphtha. The naphtha thus obtained was 'wild', that is, it had a high vapour pressure owing to the presence in it of dissolved and liquefied gas. In order to reduce the vapour pressure to a level at which the naphtha could be shipped, this gas was removed either by distilling it out through a 'stabilizing' column or, according to the practice at many wells, merely by allowing the naphtha to 'weather' in open tanks (heated by coils if necessary) until the gas had been driven off in to the air.

Jan 1, 1936

By Pierre Laliberté

Introduction ??Mine ventilation is a major consumer of power in underground mining, including air heating (winter) and air conditioning (deep mines). ??Any advances, including the development of low emission vehicles, that can improve underground air quality can reduce ventilation demand, and likewise reduce costs and energy consumption, including their associated greenhouse gas emissions.

Nov 1, 2011

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By G. H. Hope, A. R. Maycock

"La Mine Doyon is a gold mining operation located in northwestern Quebec, approximately 35 km east of Rouyn-Noranda and 85 km west of Val d'Or. The mine is jointly owned by Lac Minerals Ltd. and Cambior Inc. with Lac Minerals as the manager. Production statistics as of February 1987 are 6.4 million tonnes milled at an average grade of5.8 g/t Au. Current reserves of9.9 million tonnes at 5. 7 g/ t Au to a depth of400m have been outlined. Indicated reserves below this horizon could considerably increase this reserve.The mine currently consists of two open pit and two underground mine operations, producing approximately 3600 tonnes per day of ore at an average grade of6 g/t. The ore is currently processed at the La Mine Doyon mill at a rate of1400tid and at Lac's East Malartic mill at 1950 t/d. Ore is also processed intermittently at Lac's Les Terrains Auriferes mill and at Noranda's Horne Division.La Mine Doyon is currently in the midst of a program to expand and upgrade the mill at La Mine Doyon. The expansion to 3000 t/day includes the conversion of the existing crushing and grinding circuits to a SAG (semi-autogenous grinding) mill circuit and the existing filter wash plant to a CIP (carbon-in-pulp) recovery plant. The economics of this project are based on reduced operating costs (milling and trucking) and improved recovery due to updated technology. HistoryThe area between Noranda and Val d'Or has a long history of mining activity in both base metals and gold, dating back to the early 1930s. More recently, several new orebodies have been discovered and exploited in the area including La Mine Doyon, Lac's Mine de Bousquet, Dumagami, and the Kiena operation.La Mine Doyon was discovered in the early 1970s, and brought into limited production in late 1979. The mine was started on are reserves of 2.75 million tonnes at 6.2 g/t and was, thus, considered a small, short-term operation. Mining started at an initial rate of 550 tI d with all the ore being shipped to Noranda's Horne smelter as flux. When Lac's East Malartic mill became available for custom milling, Doyon commenced shipping to that facility at a rate of 650 t/d. As a result of some equipment additions and an improved understanding of the ore, the East Malartic mill throughput was gradually increased from 650 t/d to the current rate of 1950 t/d."

Jan 1, 1988

By F. Mercier-Langevin

ABSTRACT; Agnico-Eagle’s LaRonde mine is one of the deepest mines in Canada. Ground conditions in the deeper levels can be very challenging, ranging from hard and brittle to soft and squeezing. As a result, rock mechanics and ground control practices have had to evolve considerably to accommodate progressively deeper mining activities. This paper focuses on the deeper levels of mines and how the difficult ground conditions encountered there have influenced the mining strategy. The first section examines ground control practices and support systems in highly stressed, poor quality rock. The evolution of level layout is also presented. Finally, improvements in stope sequencing are reviewed.

Jan 1, 2010

By J-g. Cui, X-b. Guo, J-j. Wang, J. Qiao, H. Tian

"Rare earth elements have unique properties because of the special electronic structure. In this paper the improvement of refractory material performance by the light rare earth oxides was introduced. The experiments showed that adding a bit of rare earth oxide could obviously improve the performance of the refractory material. INTRODUCTIONIn recent years, refractory materials are widely applied in the steel smelting process as a ladle lining material. In China, although the total production of fire-proof material exceeds normal demand, but the quality and variety of fire-proof material still have a big gap with world advanced level. A number of refractory products need to be imported from abroad. With the rapid development of domestic steel production, the ladle lining with refractory is gradually running after the world advanced level on production technology, production variety, and quality level. It replaces some imported products meeting the needs of the development of the iron making production. Therefore, there is an important significance to research on solving the problems of the ladle refractory reasonably and avoiding or reducing blind and not proper use of the imported refractory ( Jing, 2007).On the other hand, rare earth oxide has some special excellent properties. Firstly, they are very good refractory materials with their high melting point;Next, they have good resistance to water and alkali resistance function;Thirdly, it is easy for rare earth oxide to generated composite oxide reacting with other metal oxide,achieving the purpose to improving the material properties (Xu, 1978; Diao, 1979). China has a variety of rare earth resources,and rare earth resources is more advantageous in Baotou,taking up about 36 percent of world reserves,which is the world's top of rare earth mineral. In recent years the rare earth products output has risen sharply and many varieties and specifications have appeared. So it is necessary to study the new field of rare earth compound to open up new markets. Thus, it has a very vital significance to promote the further development of rare earth industry, adjust the rare earth products structure, ease the contradiction between supply and demand, and improve refractory products quality and grade in order to better serve the main body production.I In this paper, the experiments are mainly for 210 tons of Al2O3-MgO style series refractory materials belong to ladle lining bag from Baotou Iron & Steel Group Corporation Sheet Factory. The improvement to the effect of refractory material performance is explored by using light rare earth oxides as additives."

Jan 1, 2012

By Yves Caron

Résumédes travaux effectués De septembre 2009 àmai 2011 ? Plus de 21 000 m de forages complétés en avril 2011 et près de 9 000 échantillons ? 2,7 km de décapage, 52 tranchées et 852 m de rainures ? Estiméde ressources 28 mai 2010 (SGS Géostat) ? Essais métallurgiques en laboratoire (automne 2010) ? Étude économique préliminaire (janvier 2011)

May 1, 2011

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By I-H. Jung, J. Kim

"Mg alloys are extensively used as light structural materials in modern industry. Mn and RE (rareearth) metals are effectively used as alloying elements to enhance the properties of Mg alloys. Therefore, the thermodynamic database of those alloys is important in the Mg alloy design and processing. Critical evaluation and optimization of all available literature data for the Mn-RE systems were conducted to obtain reliable thermodynamic functions. The Mn-RE systems shows systematic changes in the phase diagrams and thermodynamic properties with increasing atomic number in the lanthanide series. This systematic approach for all RE elements allows to resolve inconsistencies in the available experimental data. INTRODUCTIONRare Earth (RE) metals are widely used in many industrial fields including permanent magnet, electronic materials and structural materials. As a small addition of RE can enhance magnetic, electronic, optical and mechanical properties of numerous materials, the usage of the RE is still expanding regardless of the strategic control of their supply.Magnesium alloys are getting great scientific and industrial attention as the lightest structural materials. One of the drawbacks of Mg alloys is their poor formability at room temperature due to the limited slip system with hcp crystal structure. Recently, several studies (Farzadfar et al., 2011; Sandloebes et al., 2010; Stanford, 2010; Stanford et al., 2008; Yan et al., 2010) show that the additions of small amounts of RE can considerably enhance the ductility of Mg alloys. Therefore, a lot of research on Mg-RE alloys is undergoing to clarify the role of RE on the enhanced deformation mechanism and to find out the most optimum Mg alloy compositions. In order to respond to the need of Mg-RE alloy development, a large thermodynamic database for Mg alloys containing RE has been developed with critical systematic analysis and optimization of the entire RE series data. This includes the thermodynamic database of the Mg-RE (Kang et al., 2009), Mg-RE-RE (Kang et al., 2009), Mg-Al-RE (Jin et al., 2011; Jin et al., 2010), Mg-Zn-RE and Mg-Mn-RE systems."

Jan 1, 2012

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By R. Blazej

Machinery Systems Division (MSD) in the Institute of Mining Engineering at Wroclaw University of Technology specializes in belt conveying systems analyzing, calculating and design. Within the division operates the certified Laboratory of Belt Transportation (LTT) and Laboratory of Rollers. Since few years, a group of several people have begun work on developing a comprehensive system for the automatic evaluation of condition of conveyor belts working in the mines. Group uses both magnetic devices developed by specialized companies servicing belts and its own machine vision system developed for assessment of belts covers and edges during belt movement (up to 7 m / s) on the specially designed for this purpose the test conveyor. Recently they have got the research grant funded by the National Centre for Research and Development (NCBiR) for development of the system for automatic diagnosing of conveyor belts? condition and aiding of rational belt management. On the basis of previously created diagnostic tool called ABCDE (Automatic Belt Condition Diagnostic Equipment) the five modules: vision-A magnetic-B, preventive-C, forecasting?D, and determining safety factor-E will be developed. They will automatically interpret data about conveyor belts? condition to indicate the extent and timing of repairs, to prevent failures and to select the optimum moments for their replacements. The system will use results of ongoing research & development and planned research concerning modeling of belt wear using evolutionary genetic algorithms. The reached stage of research can not yet allow to start the implementation work by potential users. It is therefore necessary to pursuit research in real scale, the development of new modules (C-E) and intensive testing of the system in working condition with system calibration to optimize the economic effects.

Aug 1, 2013

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By A. McLean, X. Men

"With high quality sulphide ores diminishing, nickel production from low-grade oxide ores becomes increasingly important and a major concern is the high sulphur level in the resultant ferro-alloy. So, desulphurization of the ferronickel becomes an important consideration. Red mud is a waste product of alumina industry and causes adverse effects on environment. In the present study, experiments were conducted to determine feasibility of using red mud as a major ingredient of refining fluxes for ferronickel desulphurization. In view of their influence on slag-metal separation, contact angle measurements between ferronickel alloy and molten slag made from red mud were also determined. INTRODUCTIONNickel is a very important metal that finds a variety of applications including consumer products, building, automotive and electronics. There are two kinds of ores containing nickel, namely oxide and sulphide ores. Anthony and Flett [1] reported that about 55% of the world’s nickel production originates from sulphide ores while the balance of new nickel is derived from oxide ores. However, oxide ores count for about 70% of the worldwide reserves. Apparently, oxide ores will play a significant role in the production of nickel in the future. Most of nickel produced using oxide ores is from pyrometallurgical processes namely ferronickel smelting or matte smelting. So, we can draw such a conclusion that using nickel oxide ores to produce ferronickel will become more and more important .Before used to make stainless steel or other materials, the ferronickel need pretreatment to remove impurities especially sulphur and phosphorus that will cause negative influence on the properties of steel product. Red mud is a by-product during alumina production. Usually, about 1 to 1.5 tons of red mud will be produced when we get 1 ton of alumina. About 90 million tones of red mud are produced every year in the world [2].Red mud is deemed as a toxic industrial waste which needs treatment before discharge because of alkalinity and chemical and mineralogical properties. Until now, the main means to deal with red mud are to store it in impoundments or dump it in the sea depending on local environment. Nowadays, how to recycle red mud has become a pretty hot topic around the world. The last 40 years have witnessed a lot of patent applications concerning the ways of red mud utilization. However, a little amount of red mud is consumed until now due to the limitations of recycling red mud."

Jan 1, 2012