Search Documents

By Pedram Sahba

In today?s emerging economy, pooling resources is a growing trend to reduce overall system costs. Two important resources of every maintenance department are repair shops and spare parts. In this work, we consider a system consisting of mine drills at multiple areas in a mine. In each area, a number of identical drills are operational. When a failure occurs, the defective component should be repaired in a designated repair shop. The failed component can be replaced immediately if a spare part is available. Otherwise, the drill is down until a component is repaired and put back into service. In this paper, the effect of pooling resources is examined, and the conditions under which it is beneficial to pool the resources are investigated. In addition, determining the optimal number of stand-by units, equipment or spare parts, in each case is of interest.

May 1, 2013

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By J. Jerome MacDonald, Stephen B. Flewelling

"In the base metals industry of today, operations required to continuously improve productivity and reduce unit production costs. Consistent with these goals is the improvement of the muck haulage cycle from open stopes with the No. 12 Mine.Existing haulage from open stopes occurs with LHD units experience at Brunswick indicates that LHD units have a higher unit cost per tonne mucked than loader-truck combinations when the haulage exceeds approximately 150 m.The reintroduction of open stoping at Brunswick made existing loader-truck combinations unsuitable. It was recognized that application of recent continuous loading technology could potentially result in significant unit cost savings and productivity increases.A review of the technology resulted in the testing of the Voest Alpine AL60 loader in the open stopes located on the 1000m Le vel. Testing began in January 1988 and finished in late November 1988. The test will provide experience as well as quantified production and maintenenace parameters f or the purpose of quantifying production unit costs and system productivity, ultimately resulting in a decision to further utilize or not utilize the loader as a primarymucking unit at Brunswick .INTRODUCTIONBrunswick Mining and Smelting Corporation Ltd. produces approximately 10500 tonnes per day from the No. 12Mine located 35 km southwest of Bathurst, New Brunswick Mining is the largest (single mine) producer of zinc in the world having mined over 52 million tonnes since 1964. Many years of production still remain with proven and probable reserves in excess of 90 million tonnes. Reserves grade at an average of 3.65% Pb. 8.99070 Zn, 99g/mt Ag and 0.32% Cu . The operation employs 1446 people with approximately 800underground including operations and maintenance staff.In the No. 12 Mine two major mining methods are presently utilized . The primary method is Mechanized Cut and Fill (MCF) accounting for approximately 6500 tonnes per day from four major areas. The remaining 4000 tonnes per day is produced from open stopes with the majority of 2800 tonnes per day being produced by the 1000 level.The 1000Level contains 30 million tonnes segmented into open stope blocks 30 m high, 15m and 30 m on strike , with a transverse width of 10m to 50 m (Fig. I). Stopes are organized on a primary secondary stope arrangement along strike. Primary stopes are undercut and overcut full size with the back fully cablebolted. All stope and lateral development is driven 4.0 m high. All stopes to date are flat bottom (Fig. 2). Primary stopes are filled with cemented rock- fill , secondaries with conventional rockfill, Haulage from the stopes is primarily with 8-yard LHD units ; mucking is approximately 50% conventional and 50% remote. Haul distance to date has averaged approximately 150m with current stope haul distances of approximately 300m. Haulage is presently to a small jaw crusher situated on the 1000 Level. From August 1989on, haulage will be to a set of ore passes feeding to a large gyratory crusher situated on the 1200 Level. Start up of the gyratory crusher corresponds to an increase in tonnage from 1000 Level to 4100 tonnes per day."

Jan 1, 1989

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By A. D. Hunt

THIS PAPER will review Canada's fossil fuel situation as we understand it today and indicate some of the options available to meet our energy requirements during the next 15 years. It would therefore be helpful to examine Canada's total energy requirements and discuss the un certainties of the data base on which we must base future energy investment decisions. On the world scene, Canada is at the top of the energy-consuming nations, using about 49 bbls of oil equivalent per caput/ year. This appears to be slightly ahead of the U.S. and of course much higher than that of many countries. It is generally accepted that there is a more or less direct relationship between energy consumption and material standard of living. However , as we know, Canada, when compared with other industrialized countries on a GNP, an individual-income or some other standard basis, is lower in the list. This situation may be explained by our more severe climate and a relatively small population distributed over a land mass second only to that of the Soviet Union.

Jan 1, 1977

By E. Howard Lambert

"Operating costs of mining plants are increasing due to the increased cost of labour, materials and fuels. Labour and materials costs are factors not readily controlled. However, the use of energy from fuels may be controlled by plant operations. This paper describes the fossil fuels, their expected rate of depletion and their costs. The paper considers methods which may be used to provide an efficient use of energy from fuels. It includes an outline of obtaining energy, as heat, from mine milling operations (air compression) and obtaining the maximum use of energy from fuels used to generate electricity."

Jan 1, 1973

By A. Rao, J. A. Davidson, B. L. Jones, K. W. Bowes, D. Craib

Supported by ANSTO, Groundwater Science and Inception Consulting Engineers, Boss has embarked on a series of technical projects aimed at reinforcing the Project’s capability to meet its export permit production capability. This paper will focus on three aspects of this technical program: Reducing the cost of resource expansion through smart use of low cost, surface target generation techniques; Improving the rate of uranium leaching and solution stability (gypsum, jarosite) through lixiviant chemistry modifications; and Development of an ion exchange (IX) process to increase production capacity, and integration of IX and the current solvent extraction circuit with the existing uranium precipitation and product preparation circuits.

Jan 1, 2020

By J. Paraszczak

High productivity of the equipment employed is one of the key factors in reducing production cost in mining. One of the best ways to achieve it is an increase in availability. In order to identify the most adverse factors affecting it, reliability and maintainability analysis ought to be done. If its results are to be conclusive, a sufficient amount of credible and consistent data is indispensable. Following the experience from field studies done in underground mines, this paper discusses the current status of failure and maintenance reporting, as well as problems encountered. It exposes the importance of adequate data collection on failures and downtime as well as it reviews the benefits of analysis based on such material. The question of benchmarking with regards to mining equipment performance is also addressed. The paper concludes with some recommendations on data collection and processing, as well as stresses the need to standardize the most important reliability/ maintenance notions throughout the mining industry and to conceive appropriate performance measures.

Jan 1, 2000

By R. Lodha, C. Oprea, G. Oprea, H. Zargar, T. Troczynski

"The basic refractories used in non-ferrous industry contain chrome ore for improving the thermal shock resistance, thus reducing the penetration of molten metal and fayalite-type slags into the lining. The current study aims to replace chrome ore with Me4+ ions along with Fe3+ ions in order to form MgO-Al2O3- FeOx-Me4+O2 based complex spinel systems that could perform similar to the complex chromia-bearing spinel in the magnesia-chrome refractories. This system allows for lower temperatures of synthesis and sintering. In our study, compositions with 60% MgO were fired below 1500°C and resulted in complete formation of complex spinel, and open porosity less than 5%. The in-situ formation of the complex spinel from the fine mix of oxides in the MgO-Al2O3-FeOx-Me4+O2 system offers a suitable alternative of binding system to produce basic refractories at lower temperatures and of similar physical and mechanical properties with magnesia-chrome bricks fired above 1750ºC. INTRODUCTIONThe synthesis of magnesium aluminate spinel (MgAl2O4) (Maschio, Fabbri, & Fiori, 1988) or magnesium chromate spinel (MgCr2O4) from their respective oxides is diffusion controlled resulting in a sluggish reaction even at high temperatures. For instance, the diffusion of Mg2+ and Al3+ ions in the intermediate spinel layer during reaction is slower than the diffusion of Mg2+ in corundum and Al3+ in periclase. The interfacial layer of spinel formed during the reaction increases the diffusion path for the spinel forming cations. This accompanied by ~8% volume expansion retards further reaction resulting in incomplete spinel forming reaction during sintering and hence densification during the reaction cannot be achieved. In order to assess sintering studies with fine particulate oxides that would result in a lower diffusion path, a mechanical mixture of the hydroxides of aluminium and magnesium calcined at 1400ºC to 1600ºC for 1 hour does not result in complete spinel formation (Sarkar, Das, & Banerjee, 2003), which indicates that reaction sintering of stoichiometric magnesium aluminate spinel is retarded by initial reaction forming the interfacial spinel layer. The basic bricks used as linings in non-ferrous pyro-metallurgical convertors are manufactured using magnesia and chrome ore, the sintering of which produce spinel solid solution. This solid solution is a mix of both normal and inverse spinel structures that sinters at temperatures in excess of 1800ºC in air."

Jan 1, 2012

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By E. Nejati, S. Khoshkooei, V. Firouzdor, M. Akbari, F. Khomamizadeh

In this study the effects of Si content on mechanical and thermal fatigue properties of Al-Si casting alloys were investigated. Repeated heating and cooling cycles were applied on the samples at 230°C to develop thermal fatigue cracks. Crack growth mechanisms and microstructural influences were investigated by optical and scanning electron microscopy. Thermal fatigue behaviors were improved successively by increasing of silicon content up to 7wt%. However, addition of more than 9wt% silicon decreased the thermal shock resistance of the alloy. Silicon contents of about 9wt% presented the best mechanical and thermal fatigue resistance in the alloy.

Jan 1, 2006

Mineral resource development activities impact the health and well-being of many people, from workers, to families and surrounding communities. In the decade up to 2010, mining revenues increased from 6% to 14% of Australian GDP, and minerals contributed 55% of total exports, with a growth in mining employment from 1% to 1.7% of the national workforce (Connolly and Orsmund, 2011). The growth in Australia?s minerals operations is mostly located in remote areas, or in rural communities with a limited population. As a result, operations have increasingly implemented long distance commuting (LDC) programs, often called ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO), as a staffing strategy to meet rapid industry growth in locations with limited local populations. The rapid expansion of the minerals industry has resulted in considerable public debate about the benefits and costs to all sectors of Australian society. In response to the concerns of constituencies from many parts of Australia, the Minister for Regional Australia, Regional Development and Local Government, The Hon Simon Crean MP, asked the House Standing Committee on Regional Australia on Tuesday 23 August 2011 to inquire into and report on the use of ?fly-in, fly-out? (FIFO) and ?drive-in, drive-out? (DIDO) workforce practices in Regional Australia. The recently published report highlights the national interest and the diverse opinions about this practice in Australia. Resource extraction companies have developed several options to meet the accommodation requirements of their long distance commuting workforce. In this paper, initial results are reported from an ongoing survey of FIFO (and other non-residential) resource industry workers (n = 286) in the Australian resource extraction industries. The purpose of this study was to better understand how accommodation arrangements may impact on the health, wellbeing and job satisfaction of non-resident workers; and to attempt to find a relationship between different accommodation variables and workforce wellbeing and retention. In doing this it investigates evidence for the linkage between accommodation factors, hours of work, health, well-being, job satisfaction and job retention in the LDC work force.

Aug 1, 2013

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By D. R. Boyle

"The basal type uranium deposits in south central British Columbia occur within unconsolidated, late Miocene fluvial paleochannel sediments that overlie major fault zones within the Okanagan Highlands Intrusive Complex. Prior to the formation of mineralization, paleovalleys containing host sediments were flooded by Pliocene valley basalts of the Plateau Basalt Formation. Five uranium deposits have been outlined to date, of which the Blizzard (4020 tonnes U) and TYee (650 tonnes U) are the largest. The basement intrusive complex underlying the deposits varies in age from early Cretaceous to Eocene and is comprised of quartz monzonite, granodiorite, Coryell monzonite, porphyritic granite and pegmatite.The mineralized host sediments comprise a complex sequence of interfingering conglomerates, arkosic sandstones and mudstones. Organic material is abundant in many, but not all, mineralized beds. Uranium mineralization is present in the form of uranous (ningyoite) or uranyl (saleeite, autunite) phosphates coating clastic grains and filling voids. Because of very strong reducing conditions related to large concentrations of marcasite and organic material, ningyoite is the only uranium mineral in the Tyee deposit, whereas the Blizzard deposit contains a more complex assemblage of minerals (saleeite, autunite, ningyoite). The observed paragenetic sequence of mineral precipitation in the Blizzard deposit (autunite-saleeite-ningyoite) indicates that the uranyl minerals, saleeite and autunite, are primary. Small amounts of Zn, Ni, Co and Mo have been introduced into the Blizzard deposit whereas Mo is the only non ore-forming element enriched in the Tyee deposit. Mn is the only depleted element in both deposits."

Jan 1, 1986

By R. K. Collings

"This paper summarizes research that was done at the Mines Branch, Ottawa, to evaluate samples of phosphogypsum for gypsum products manufacture. The samples were from phosphate fertilizer facilities at: Port Maitland, Ontario ; Valleyfield, Quebec; and Fort Saskatchewan and Redwater, Alberta. All samples were wet-screened, washed, filtered and calcined in a laboratory kettle at atmospheric pressure. Tests were also made at higher pressures in a small autoclave. The gypsum and resulting hemi-hydrate, being acidic, were treated before, during and after calcining with various bases. The hemi-hydrate products were checked for time of set, compressive strength and bond to gypsum wallboard paper. The results of this study indicate that phosphogypsum from each of the sources investigated has potential as a substitute for mined gypsum in gypsum products manufacture. Pilot-scale testing is recommended to confirm that the product would be satisfactory for the manufacture of plaster products on a commercial basis."

Jan 1, 1972

By W. Mueller, M. Rocheleau, E. Dimroth

The paleogeographic evolution of the Abitibi Belt is subdivided into three phases, namely: 1) a phase of the growth of a submarine volcanic chain, 2) a phase of the emergence and growth of volcanic islands and 3) a phase of uplif t and erosion of volcanic islands. Isostatic calculations suggest that the volcanic sequence in the south of the Abitibi Belt rests on oceanic basement or on the mantle; the volcanic sequence in the north of the belt rests on about 13-14 km of tonalitic basement. 10-15 km of plutonic material accreted to the volcanic islands during paleogeographic phases 1 and 2, and caused the uplif t during paleogeographic phase 3.

Jan 1, 1984

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By C. Cutts, K. Wheatley

The Dragon Lake Zone (uranium prospect) comprises a N160º trending vein that is approximately 110 m long, up to 5 m wide and from 1 to 40 m high. The zone is mostly within altered sandstone of the Fair Point Formation, the basal unit of the Paleoproterozoic Athabasca Group, but it also extends downward (up to 3.5 m) into basement rocks that occupy the northerly trending Maybelle River Shear Zone (MRSZ). This subvertical shear zone separates graphitic paragneiss and weakly deformed granitoid rocks to the east from non-graphitic paragneiss and foliated granitoid rocks to the west. The Dragon Lake Zone cuts across both the MRSZ and N060º-N070º-trending cross-faults that offset the shear zone but not the mineralized vein, which contains values up to 54.5% U over 50 cm core length. Strong chloritization occurs in graphitic paragneiss and sandstone adjacent to mineralization. Silica was depleted from the basement rocks and redeposited at the borders of the 5-15-m-wide alteration zone, as well as within overlying sandstone of the Manitou Falls Formation. There are minimal alteration effects in the overlying Lazenby Lake Formation. Geochemistry shows that the alteration zone in the Fair Point Formation is highly anomalous in metals, most notably in Ni, As, U, Pb, Co, and B. Clay within this zone is illitic and Fe-rich chlorite is also present. Brittle deformation is not as widespread or as well developed in the Fair Point Formation as it is in the overlying Manitou Falls Formation, which is extensively brecciated and contains some anomalous metal values.

Jan 1, 2013

By H. A. Baxter

THE Eustis concentrator is located about nine miles southwest of Sherbrooke, on the main line of the Quebec Central railway. The concentrator is served by a side track parallel to the main line, and all supplies for both the mine and mill are delivered at the mill yards. The concentrator treats 250 tons of copper-iron ore daily by preferential flotation, whereby, first, the copper sulphides are floated and the iron pyrite is depressed, and, second, the iron pyrite is reactivated and floated, resulting in an iron pyrite concentrate and tailing, the latter going to waste. During 1934, 71,709 tons of ore were treated, averaging 3.712 per cent copper and 32.1 percent iron, with a small amount of silver and a trace of gold. The recovery was 93.77 percent of the copper, and 70.43 percent of the iron as iron concentrate. The copper concentrate produced averaged 25.623 percent copper and the iron-pyrite concentrate averaged 42.13 percent iron and 49.173 percent sulphur. HISTORY The first mill at the Eustis mine was built in 1904 (1). For a few years previous to this rime, some jigs had been operated to concentrate the fines from the mine, the coarse ore being hand-sorted. Both the fines and sorted lump ore were shipped to acid plants. The building of the mill was based on test work carried out by Professor Robert H. Richards at the Massachusetts Institute of Technology. The method of concentration consisted in careful classification in a Richards classifier, which made six different sized products. These products went to Wilfley tables, where a concentrate, middling, and tailing were made. The middling was returned to the rolls. Crushing was done by a jaw crusher and two sets of rolls, resulting in a screen size of about five-mesh.

Jan 1, 1936

By Young Hyun Paik, Hyung Sup Choi, Yeun Sik Kim

The basic studies on the surface properties and flotation characteristics of ilmenite were made by electrophoretic, adsorption, contact-angle and floatability measurements. The isoelectric point of ilmenite is found to be at pH 5.6. By combining the results of electrokinetic studies and adsorption measurements, a clearer picture of the ilmenite-solution interface was observed. These findings were correlated with the floatability of ilmenite obtained by Hallimond tube tests. The general flotation characteristics of ilmenite are compared with those obtained for magnetite and rutile. It is indicated that the above three minerals, namely, ilmenite, magnetite and rutile, have very similar surface properties and flotation characteristics. Therefore, it is difficult to make an effective separation of these minerals by flotation. However, it is found that sodium orthophosphate acts as a selective depressant for magnetite in anionic flotation. Therefore, close pH control of the pulp in the presence of the phosphate ion enhances the possibility for a successful separation of these minerals.

Jan 1, 1967