Search Documents

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By Taisuke Sakakibara, Shinya Suzuki, Tatsuya Kato, Chiharu Tokoro, Kenichi Muto

Surface complexation using a diffuse layer model were constructed for arsenic (As(V)), zinc (Zn(II)) and silicate (Si(IV)) for aluminum hydroxide in the co-precipitation process. From experimental investigations using isotherms, zeta potential measurement and XRD analysis, it was confirmed that co-precipitation involved not only surface complexation but also surface precipitation. However, surface complexation was major mechanism for As(V), Zn(II) and Si(IV) removal under the target removal level of the Japanese effluent standard. In surface complexation modeling, exchange capacity of aluminum hydroxide was determined from specific surface area obtained from experimental measurement and site density obtained from reference. Surface complexation coefficients were determined by fitting the removal property and sorption isotherm obtained from co-precipitation experiments. These parameters were in agreement with the numerical parameters found by Karamalidis and Dzombak (2010) who reported a database of adsorption equilibrium constants for gibbsite. The surface complexation models constructed in this study were applied to neutralization process of an actual AMD treatment. Our model could successfully represent the pH edges for As(V), Zn(II) and Si(IV) in the neutralization of AMD.

Jan 1, 2015

By E. Michelotti, M. Cardu

This paper presents the results of a new method that has been tested to recover metallic cobalt lost by diamond beads from rock cuttings. When dimension stones are cut using diamond wire saws, the beads become worn and, before the end of their cycle life, lose a certain amount of material; this material is prevalently made up of sintered metal and diamonds. The material is then washed away, together with rock debris, in a dilute pulp. In effect, this process involves the dispersion of economically valuable, but potentially polluting, materials (such as cobalt) that are used to confer indispensable technological features to the beads. This current research aims to develop a waste-processing pilot plant (High-gradient Magnetic Separator or HGMS) to recover metallic components from the pulp by means of a suitable separation. The research\u2019s purposes are two-fold: a. to remove the polluting components from the rock debris before their disposal and b. to start a recycling process of the valuable metals.

Jan 1, 2010

By R. S. Jones

"Fording Coal Ltd. is now in its fifth year of a 15-year contract to supply 3 million long tons of clean coal per annum to its Japanese steel-making customers. The mine employs both conventional truck-shovel and unconventional ""walking"" dragline coal mining techniques in multiple-seam pits. This paper describes the present and future application of the 60-cu.-yd dragline and truck-shovel pre-stripping fleet in 1•ecovering 5- to 40-footthick coal seams in mountainous terrain. Deep blastholes, coal flow demands, spring ""run-off"", seam and inter-seam thrust faulting, limited seam outcrop data and regional faulting are a few of the problems encountered in this application. The author discusses these problems and their solutions as applied at Fording Coal Ltd."

Jan 1, 1976

By M. Nusheh, C. Bumby, A-H. Puichaud

"Vanadium-bearing titanomagnetite ironsand deposits occur along a 480 km stretch of the west coast of New Zealand. In the present study, the leaching behaviour of NZ ironsand was investigated in hydrochloric acid (2–10 M) solution at 50–80°C for 2 h. The resulting leaching liquors exhibited Fe/V ratios in the range 150–180. The distribution of trace element contaminants between solution and solid residue was investigated, and processing conditions have been determined for rapid and efficient dissolution of Fe, Ti and V into the leaching solution. In addition, mineralogical analysis of raw ironsand and leached residues was performed in order to study the leaching mechanism. Samples were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy (EDX), X-ray fluorescence spectroscopy, qualitative and quantitative X-ray diffraction and inductively coupled plasma mass spectrometry (ICP). Results indicate that the dominant dissolution process follows shrinking particle mechanism. However, ironsand particles containing ex-solution lamellae exhibited a different leaching behaviour compared to homogenous titanomagnetite particles.INTRODUCTION Titanomagnetite ironsand (blacksand) forms Quaternary onshore beach and dune deposits and offshore marine deposits (Figure 1) along 480 km of coastline from Kaipara Harbour south to Wanganui on the west coast of the North Island (Christie, 2016). It attracted the attention of scientists from the earliest times (Galbreath, 1998). The principal minerals in ironsand are titanomagnetite (TTM), ilmenite, quartz and ferromagnesian minerals such as augite, hornblende, diopside, and olivine with smaller amounts of rutile and apatite (Mauk, 2016).Several large ironsand deposits have been discovered and exploited since the late 1960’s. The Waikato North Head and Taharoa mines are currently operating and they have a 2015 measured resource of 400 million tonnes in total and provide over 2 million tonnes of concentrate per year by simple cost effective magnetic separation process (Christie, 2016; Christie & Brathwaite, 1997). The concentrate contains not only 7–8% TiO2 and 56–60% SFe, but also 0.3–0.6% V2O5, is both a valuable titanium mineral and a source of vanadium. All the production is used for steelmaking industries. The other potential for utilizing more of this resource without requirement of integration into an iron and steel producing plant is to develop a hydrometallurgical route with advantages of higher efficiency along with lower emissions. Currently, there is no existing commercial process capable of extracting all three of these elements as industrial-grade commodity products. Acid leaching of TTM concentrate with higher degrees of recovery and selectivity is a key step in any possible hydrometallurgical route."

Jan 1, 2017

By M. Bryson, S. Broom-Fendley, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho, S. Al-Ali, F. Wall

The Songwe Hill Rare Earth Element (REE) Project in Malawi is a near surface carbonatite-hosted deposit with synchysite and apatite as the key REE bearing minerals. A strong focus has been placed on understanding the REE mineralogy of the Songwe Hill carbonatite as REE mineralogical characterization is a crucial component at all steps, ranging from exploration to production, in the development of REE deposits. Extensive mineralogical work has been completed at Camborne School of Mines (CSM), Natural History Museum (NHM) London, British Geological Survey (BGS), Nottingham, Aberystwyth University, Wales, Mintek, South Africa, and SGS Inc. Canada (SGS). The following analytical techniques were used: scanning electron microscopy (SEM), electron microprobe analysis (EMPA), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and QEMSCAN®. The detailed studies have demonstrated that while synchysite is light-REE enriched as expected, apatite, abundant in all stages of carbonatite emplacement at Songwe, is anomalously enriched in mid- to heavy-REE relative to apatite in other carbonatite deposits. The distribution of REE within synchysite and apatite at Songwe has had important implications for the direction of the metallurgical work with respect to the behaviour of light and heavy REE through the flotation and hydrometallurgical stages of the flow sheet.

Jan 1, 2014

By J. Trojacek

A large-scale development in exploration and production of uranium ores in the Czech Republic was done in the 2nd half of the 20th century. Many uranium deposits were discovered in the territory of the Czech Republic. Over a period of 50 years approximately, 110 000 tons of uranium in concentrate were produced. Different mining methods were developed and used. One of the most considerable deposits in the Czech Republic is the site Hamr na Jezere ? Straz pod Ralskem where both mining methods ? the underground mining and the acidic in-situ leaching ? were used. The extensive production of uranium led to widespread environmental impacts and contamination of groundwaters. Over the period of ?chemical? leaching of uranium (ca. 32 years), a total of more than 4 million tons of sulphuric acid and other chemicals have been injected into the ground. Most of the products (approximately 99.5 %) of the acids reactions with the rocks are located in the Cenomanian aquifer. The contamination of Cenomanian aquifer covers an area larger than 27 km2. The influenced volume of groundwater is more than 380 million m3. The total amount of dissolved SO4 2- is about 3.6 million tons. Approximately 0.5 % of the contamination is located in the Turonian aquifer. After 1990, a large-scale environmental program was established and the Czech government decided to liquidate the ISL Mine and start the remediation in 1996. The remediation consists of contaminated groundwater pumping, removing of the contaminants and discharging or reinjection of treated water. The objectives of the remedial activities are the followings : to restore the aquifer to a condition guaranteeing continuing usability of Turonian water of Northern Bohemia Cretaceous, to decommission boreholes and surface installations and to incorporate the surface of leaching fields into the ecosystems taking into account regional systems of ecological stability and urban plans. Nowadays four main remedial technological installations for reaching of these aims are used - the ?Station for Acid Solutions Liquidation No. One?, the ?Mother liquor reprocessing? station, the ?Neutralization and Decontamination Station NDS 6? and the ?Neutralization and Decontamination Station NDS 10?. Total capacity of this complex is sufficient to reach the target values of remedial parameters in 2037. The remediation action consists of: pumping of residual solution to the surface, separating uranium from the solution and reprocessing contaminants into commercially usable or ecologically storable products. It is expected that the amount of withdrawn contaminants will vary from 80 000 to 120 000 tons per year. Total costs of all remediation activities are expected to be in excess of 1.5 billion EUR.

Aug 1, 2013

By Martin Lebeuf

The phenomena occurring in the cathode and at the cathode surface of aluminum electrolysis cells are very important in regards to cathode voltage drop and cathode wear. In the current study, laboratory-scale aluminum electrolysis cell cathodes were analyzed by X-ray microtomography. This technique allows an excellent visualization of the distribution of different substances, if their respective X-ray attenuation coefficients are different enough. In the current case, the important difference in the mean atomic number between cryolitic bath and graphitic carbon results in good contrasts. The volumetric bath penetration profile, porosity and impurities distribution in the cathode were thus obtained. Furthermore, metallic impurities and bath heterogeneities were observed at the cathode surface. Observations were also made with Scanning Electron Microscopy - Energy Dispersive Spectroscopy (SEM-EDS).

Jan 1, 2011

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By Côme Carbonneau

The ten -year case history of La Société Québécoise d'Exploration Minière (SOQUEM) is reviewed under the headings of the company's raison d'être, objectives, policies, structure and final goal. A brief analysis of its past operations is presented: aborted efforts, findings and developments. A projection is made of the future earnings, in terms of estimated present value, of its three main discoveries - Louvem , Niobec and Selim.

Jan 1, 1978

By J. R. Porter, C. Panaou

"A significant effort is expended on preparation of the capital estimate for feasibility studies. The development of the operating cost estimate is usually allocated a significantly smaller budget and less emphasis is placed on ensuring the accuracy of the operating cost. This paper presents a comparison of capital and operating costs of hydrometallurgy processing plants in order to demonstrate the importance that variations in operating costs have on the overall life-of-mine costs. The analysis is supported by a case study on the operating costs of a water treatment plant at an existing Australian hydrometallurgy facility at the feasibility design level. INTRODUCTIONDetermination of the economic validity of a minerals processing project is a critical outcome of a feasibility study. In many cases, the financial results of the feasibility study will determine if the project should proceed to execution. Ensuring that these results are reliable and built upon sound engineering practices allows companies to make informed decisions on resource opportunities and the selected technology.The methodology for developing a capital cost estimate at the feasibility level is well established. Specialist engineering estimators use budget quotations, first principle estimation and rules-of-thumb to develop an estimate with an accuracy of typically -10% to +15%. Cost reporting software packages are used to methodically build up the estimate from design information supplied by the engineering disciplines. Risk analysis and capital expense workshops are carried out to identify potential deficiencies in the estimate. It is widely recognized that in order to successfully produce a feasibility level capital estimate with an appropriate level of accuracy, a rigorous development process is necessary.The development of the operating cost estimate is typically less rigorous than the capital cost estimate. The operating cost is normally derived by the process engineering discipline and rarely are specialist estimators used to support the development. The allocated budget for producing an operating cost is usually smaller and less emphasis is placed on ensuring the accuracy and contingency reflect the most likely operating cost scenario."

Jan 1, 2012

By Karl J. C. Harries

"4.1. INTRODUCTIONThis chapter, although divided into four parts, deals with only two principal topics. The first briefly describes and discusses some common types of property interests and considerations relating to them and the second deals with entering upon privately owned lands and obtaining the consent to do so.It should be noted that the terms “mining rights” and “mineral rights” are used interchangeably. As so used, they include the right to exploit the minerals and dispose of them for the benefit of the owner/lessee. This is relatively common in common law jurisdictions. In some jurisdictions, the two terms have distinct meanings, with “mining rights” referring to the right to work or exploit the minerals and “mineral rights” referring to the minerals themselves.Finally, it must be mentioned that the comments in the Introduction and §§ 4.2., 4.3. and 4.4. are based primarily upon Ontario law and Ontario’s mining and real property systems of registration. They have been included for illustrative purposes.4.2. LICENCES, CLAIMS, AND LEASESIn most jurisdictions, there are several basic types of interests that can be obtained from the state for mining purposes and that are of interest to the explorationist, as opposed to the operator. Different jurisdictions will have variations of these and possibly some extra ones that will address special purposes or local concerns. In virtually every jurisdiction, privately owned property rights are obtained through negotiation between owner and acquiror.Exploration or prospecting licence. This licence grants to the holder the right to prospect over a large tract of land and the exclusive right to acquire mining claims within that tract for the term of the licence. Such licences are usually negotiated documents requiring a minimum expenditure during the first year (often secured by a deposit or surety bond) and minimum annual expenditures thereafter to continue the licence in force up to its full term. The term will rarely exceed four years. The number of claims permitted to be staked will be limited in some way, possibly as to a maximum aggregate area or a maximum number of claims per annum. It is normal for the holder to have to drop part of the licensed area each year, so that the area shrinks annually, although exploration expenditure requirements will usually increase.These types of licences are usually used by governments to encourage exploration of otherwise unattractive or remote areas, such as the far northern parts of some of Canada’s provinces. They do not grant any real property interest in the area for which they are issued, and they will be subject to any claims or property rights that exist in the area. They are contracts with the state that grant certain exclusive rights in return for commitments to carry out work. They may or may not be specifically authorized by statute."

Jan 1, 2003

By Gang Mei, Nengxiong Xu, Yanlin Zhang

After open-pit mining finishes, an iron mine with steeply inclined ore-bodies will generally transform to underground mining. Non-pillar sublevel caving method, with horizontal slice mining from up to down, is commonly used for mining deep ore-bodies under the open-pit bottom. As horizontal slice mining proceeds, a gradually enlarging goaf will be formed under the open-pit bottom, the rocks surrounding the handing and heading sides of the goaf will collapse continuously, and then these results in rock-mass failure with large deformation and displacement in the open-pit slope. Based on FLAC3D, a modeling approach to predict pit slope deformation and failure induced by transitioning open-pit to underground mining is proposed in this paper. This method mainly consists of three procedures of modeling, i.e., mining modeling, landslide modeling, and filling modeling, of which landslide modeling is the core of the proposed approach. In the procedures of modeling with FLAC3D, iteration non-convergence is taken as a local failure criterion of pit slope. When iteration calculation cannot converge, the sliding modeling will start by deleting some elements with large displacements, and finish until convergence. Before modeling landslide, several displacement contours of rock-masses in the pit slope are searched out, and each contour is an approximate possible sliding surface of the open-pit slope. From these contours, the most proper one is selected as the slope sliding surface by using the iteration calculation convergence and minimum element deletion as the judgment condition. Landslide modeling is then realized by removing the elements outside the slope sliding surface. Finally, to demonstrate the effectiveness, the proposed approach is used to simulate the process of open-pit to underground mining at Yanqianshan Iron Mine, and to predict the deformation and failure characteristics of open-pit slope during underground mining. The case study results show that: the prediction of the slope stability determined by using our method is consistent with that calculated by using the limit equilibrium methods.

Jan 1, 2015

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By O. Peters, D. Lascelles, R. Caldwell

Ageing tests on a crushed Cu-porphyry ore were conducted to assess the impact of sample oxidation on flotation performance. The objective of the testwork was to simulate ageing of ore that would be blasted through block caving but not milled for possibly several months. Ageing was performed in specially designed columns, using site and deionised water to keep the samples moist over the entire ageing period. Samples from each ageing interval (0, 0.5, 1, 2, 4, and 8 months) were examined for physical and metallurgical changes resulting from the ageing process through chemical analyses, size analyses, and batch flotation tests.

Jan 1, 2009

By P. M. May, V. Gella

The deportment and speciation of trace elements during mining and minerals processing is becoming an area of increasing concern with regards to potential health and environment risks. The use of chemical modelling can enhance our basic understanding of the deportment and speciation of trace metals under conditions present in gold processing solutions, and assist in laboratory and field investigations. In this paper, we report the results of chemical speciation modelling using the JESS software package for the trace toxic elements Pb, Cd, Hg, Se and Te in cyanidation solutions of varying salinity and relate the models to experimental data. The speciation of mercury is examined in detail.

Jan 1, 2011

By A. G. Spencer

"The horsepower required to drive large grinding mills has increased dramatically during the past ten years. Limitations on the amount of power which may be transmitted by a single gear and pinion have resulted in the application of multimotor drives, with consequent loadsharing problems. It has also sparked the development of some entirely new drive concepts. In addition, the severe demands made upon the electrical system during the acceleration period have required that the selection of motors and electrical system design be closely coordinated. Moreover, the installation of such large process units results in downtime being very costly. The equipment selected and the plant maintenance philosophy must therefore be such as to minimize the risk of unscheduled downtime."

Jan 1, 1972

By P. J. Bourassa

Incorporated in 1957 under the laws of the Province of Quebec, Quebec Cartier Mining Co. undertook the development of its low-grade iron ore reserves located at Lac Jeannine in the southwest extremity of the Quebec-Labrador trough. This challenge comprised the construction of a 200-mile access road, two towns, a 191-mile-long railroad from Port Cartier to Lac Jeannine, a hydro-electric generating plant on the Hart Jaune River, and mining, crushing, concentrating and ancillary facilities to support a yearly production of 8.0 million tons of iron ore concentrates at 66% Fe. In order to meet increasing market demands for iron ore concentrates concurrently with the depletion of its Lac Jeannine reserves , Quebec Cartier announced, late in 1969, the first step toward bringing into production a new iron ore deposit, known as Mount Wright, located 70 air miles northeast of Lac Jeannine and 25 miles southwest of Labrador City, Newfoundland. In September 1970, the company announced its decision to develop and bring into production its Mount Wright reserves at an annual rate of 1 8.4 million dry long tons. The scope of this project included the construction of an access road linking the mine, the new town and Labrador City, Newfoundland, the extension of the railroad by some 86 miles, the construction of an ore concentrating plant with all the ancillary facilities, the development: of the mine, the construction of a pourer transmission line and a new town adjacent to Lake Daviault. The Mount Wright story is divided into five individual papers covering: (a) the history and development of the project; (b) the mine; (c) plant control by a process computer; (d) crushing, grinding and concentrating; and (e) the townsite of Fermont.

Jan 1, 1977

By Zhiwei Wang, Chunsheng Qiao

"Aiming at the problems of the existing calculation methods for the support pressures of shallow tunnels in layered jointed rock strata, by using OAT (orthogonal array testing strategy) and DEM (distinct element method), 12 influencing factors including the thickness of the weathered overburden, and the states of the rock joints were considered. Then, the classification of the loosening zone was analysized. On this basis, by using the DEA (data envelopment analysis) theory, quantitative analysis on the influencing factors was conducted. By analyzing the influence of the key factors, a prediction formula of the boundary of the ringent trumpet-shaped loosening zone was established. According to principles of stress transformation, the formula of support pressures of the loosening zone which could considering the key factors were deduced. Finally, a practical case was introduced and studied to verify the proposed method.INTRODUCTIONIn recent years, various urban subway tunnels are increasingly carried out through jointed rock strata in many cities. Rock masses are discontinuous mediums with fissures, fractures, joints, bedding planes, and faults. The frequency of joints, their orientation with respect to the engineering structures, and the roughness of the joint have a significant importance from the stability point of view. However, there is a lack of understanding about the influence of the joints on the stability of tunnels. Therefore, how to measure the degree of the joints’ influence is a problem that needs to be solved.For the calculation of the support pressures, until now, many research results were focused on soil ground (Bierbäumer 1913; Terzaghi, 1943; Peck, 1969; Sabatini et al., 1999). In terms of site tests and model indoor tests, by measuring strut loads and calculating earth pressure based on strut spacing, the results proposed by Peck (1969) and Tschebotarioff (1973) have been widely used in practice for designing excavation support systems under sand (drained) and clay (undrained) soil conditions. Note that, it is unclear whether these findings could be extended to rock strata. For numerical simulations, how to simulate the states of the rock joints is a key problem that needs to be solved."

Jan 1, 2015