Search Documents

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By B. van Beek, T. Goff, P. Gebski, P. Szyplinski, W. L. Ying

"Monitoring the refractory lining integrity is essential to assure the safety of the operators and to determine the remaining campaign life of a furnace. Early detection of refractory lining degradation is essential to avoid sudden furnace failures and prevent unscheduled shutdowns. In the mid-1990s a stress wave propagation technique was developed and since then it has been utilized by Hatch Non-Destructive Testing (NDT) Group to evaluate furnace linings. For the last 17 years the AU-E technique evolved in terms of hardware, software and signal acquisition and interpretation. Most importantly, based on more than a decade of commercial applications, an extensive database of various failure modes, refractory deterioration trends and material properties has been created. This knowledge base is an integral part of AU-E which progressed from a NDT technique towards a comprehensive approach for furnace condition monitoring. All of the improvements introduced over the last several years have greatly improved the accuracy of the measurements. The data analysis process has also become more time efficient making the critical results available to the furnace operators in a more timely manner. Today the AU-E technology is used on a variety of process vessels in non-ferrous, glass, chemical and iron and steel industries.In this paper we are reviewing the available techniques for furnace refractory lining measurement and discussing the pros and cons of each method. The need for continuous improvement and development of new techniques for refractory monitoring is also emphasized. Finally, we are presenting a number of case studies and comparisons between the physical verifications and the AU-E measurements."

Jan 1, 2015

By M. Girard, E. Bourricaudy, M. Ashbury, M. Canizares, A. Mezei

Liquid-solid separation and slurry handleability relate directly to commercial plant ramp-up success or lack thereof. The paper provides a well-proven approach for testing, scale-up and commercial application of difficult processes. Emphasis is placed on practical applications of rheological concepts developed both academically and empirically. The cause-effect relationship between the process chemistry and possible physical implications on the metallurgical plant operability is presented in a simple, direct form. Examples include recent results in areas of mineral processing and extractive metallurgy. Technical process risk factors and their mitigation are included in the discussion.

Jan 1, 2011

By C. M. Bartley

Fluorspar, in addition to its familiar uses as a metallurgical flux and as a source of the electrolyte for aluminum production, has become important as an essential raw material in the rapidly growing fluorine chemical industry. The unique ability of fluorine to react and form compounds with al-most all other chemicals has made it one of the important elements in modern chemistry. Research and development over the past thirty years have resulted in a current annual production of fluorine chemicals that is both technically and economically important to industry. Because many of these chemicals and products are relatively new, and most have properties that are not duplicated by other materials, the present uses are expanding rapidly and new applications are being reported continually. Fluorspar, the only immediate and practical source of fluorine, is therefore an important mineral. This fact has been recognized in major industrial areas such as the United States and Western Europe, but has received little attention in Canada.

Jan 1, 1962

By Sherwin F. Kelly

"THE TITLE I have chosen is certainly not one of those self-explanatory ones. I shall endeavour to make its significance clear during my remarks but, in the hope of minimizing that inevitable exodus which follows a good lunch such as this, I am going to withhold the final key to its meaning until the very last sentence of this talk.Some explanation is due at the beginning, however, so for those of you unfamiliar with Spanish I will explain that casa means house, or home. The casa about which I am going to talk necessitates a wide .and generous interpretation of the word, because I am using it to indicate principally that portion of the North American continent which is the home, in the western hemisphere, of British and American ideals of justice and freedom, the dignity of the individual and his right to exercise private initiative .and engage in private enterprise. In a wider sense, I am including the entire western hemisphere, which may yet stand as the last bulwark of political and industrial democracy.As for the treasures of which I am about to speak, may I remind you that there are no• material treasures but those derived from the earth, and they are derived by one of two processes, -mining and farming. These two fundamental industries are the basis, and the sole material basis, of our welfare, our wealth, our very existence. From farming, whether it be farming of the land. or farming of the sea, we obtain the food to keep us alive, healthy and able to work."

Jan 1, 1955

By A. Roy MacLean

"In the Maritimes, there are twelve coal areas. From east to west, these include the Sydney coal field, the St. Rose - Chimney Corner, Inverness, Mabou, Port Hood, Pictou, Colchester - Debert, Springhill, Joggins - Chignecto, Beersville, Lake Stream, and Minto. The first eight are in Nova Scotia while the remaining four are in New Brunswick.In all these areas, the coal was formed during the Carboniferous period, which existed some 300 million years ago. However, within this period not all coal formation took place during the same time. There were three main intervals, which occurred at the time that the Riversdale, Cumberland and Pictou groups were laid down (Hacquebard, 1970). The oldest coals are those of the Riversdale Group. These coals were of rather limited extent, and only a few mineable seams are present, particularly at St. Rose -Chimney Corner and Port Hood. From these two areas only 2 M tons have been extracted, and 'measured' resources of 7 and 9 M tons respectively remain. The Cumberland Group coals are confined to Cumberland County and include the coals of Springhill and Joggins River Herbert -Chignecto. Some 43 M tons have been removed and only 7 M tons of 'measured' coal remain, with an addit10nal 39 M tons of 'inferred' resources. However, there are additional resources at Springhill, which will be discussed in more detail in a later section. The coals of the Pictou Group are the youngest and the most abundant, both in actual number of seams and in regional distnbution. These coals were formed during the Westphalian C and D, a time during which the main coal deposition in Europe also took place. Here belong the coals of the Sydney, Inverness, Mabou, Pictou, Debert, Beersville, Lake Stream and Minto fields. Their total production amounted to 469 M tons or 91 % of the Maritime total of 514 M tons. The remaining resources of all Pictou Group coals have been calculated at 254 M tons of 'measured' coal and 949 M tons of 'inferred' coal. As can readily be seen, the bulk of both past production and remaining resources occur in the Sydney coal field. The Sydney figures represent 73% of total production, and 87% of total 'demonstrated' resources in the Maritime Provinces. Next to Sydney, the Pictou coal field has been the greatest producer, with 59 M tons; it also has the second largest 'measured' resources, amounting to 25 M tons. However in terms of 'inferred' coal resources, the Mabou coal field, ~ith 140 M tons, ranks second to Sydney."

Jan 1, 1985

By C. P. Moore, G. W. Taylor

Vertically dipping lenses of nickel-copper ore at Dumbarton Mines Limited are being mined by a modified blasthole stoping method. The principal access to the mine is provided by a 15-degree decline, which, in conjunction with the use of ramps and declines for secondary access, maximizes the accessibility and mobility of trackless mining equipment. Sublevels are driven in ore on 80-foot vertical intervals and subsequently the ore, ranging in thickness from 15 to 30 feet, is slashed to its limits by a procedure of face sampling and test holing. Two longhole drill jumbos are used to drill off 40-foot vertical slices above and below these levels. Following blasting, the ore falls by gravity to the 500-foot horizon, where it is removed from drawpoints by load-haul-dump units and transported by truck to the main orepass. The rock is crushed to minus 3-4 inches and conveyed to surface by a 30-inch-wide wire rope suspended conveyor. This is achieved in two flights, a lower one of 290 feet and a main flight of 2260 feet. All aspects of the mining operation are discussed in the paper, including ventilation, services and safety.

Jan 1, 1973

By Amauri Garcia, Rodrigo Valenzuela Reyes, Noé Cheung, José Eduardo Spinelli, Leonardo Fernandes Gomes, Rafael Kakitani

"The present research work deals with directional solidification (DS) of both Al-15wt.%Si and Al-15wt.%Si-1.5wt.%Mg alloys and further characterization of the related microstructures. The growth of refined primary Si and refined eutectic is well-known as positive in order to improve mechanical properties of the Al-Si based alloys. Alloying is also an effective method to strengthen the Al-Si based alloys, in which Mg is considered an important alloying element. However, lack of investigation regarding the effects of Mg on microstructure of these alloys is noted. So, in the present research work emphasis is given on both dendritic and eutectic growth being affected by solidification kinetics (V-growth rate and G-thermal gradient) during transient directional solidification. Experimental evolutions of microstructural spacing of both alloys have been determined which becomes possible to understand the effects of Mg coupled with the effects of growth rate on the final microstructural arrangements. A direct comparison of the tensile mechanical properties obtained for the alloys is also performed. It is shown by these correlations that the addition of Mg generally improves the tensile mechanical resistance with a minor decrease in ductility. Furthermore, the Scheil solidification path of the ternary Al-Si-Mg alloy was determined using the computational thermodynamics software Thermo-Calc, resulting in the following sequence of precipitation: Liquid-Si-a (Al)+Si- a(Al)+Si+Mg2Si. This sequence is compared with the experimental microstructure findings.INTRODUCTION Al-Si alloys containing from 4wt.% to 22wt.% Si comprise more than 90% of all Al-based castings. Parts manufactured with these alloys have a wide range of industrial applications due to their excellent castability, crack resistance, good corrosion resistance, good weldability, low density and high strength (Bray, 1976; Zolotorevsky, 2007; Reyes, 2017). Hypereutectic Al-Si alloys are widely used and researched in the automotive and aerospace sectors due to the low coefficient of thermal expansion, resistance at high temperatures, good wear resistance and high strength (Reyes, 2017; Tebib, 2013). Above the equilibrium eutectic composition (~12.5wt.%Si) the amount of primary Si particles becomes significant (Lasa, 2003). In the place of conventional hypoeutectic Al–Si, there is growing interest in hypereutectic Al–Si alloys as a candidate material for the high-quality engines because a higher volume fraction of silicon may bring about superior properties (Matsuura, 2003)"

Jan 1, 2017

By Jean-Marc Lulin

"Depuis 1906, près de 130 gisements ont été découverts dans la inture archéenne polymétallique (Cu, Zn, Au, Ag) du nord-ouest québécois. Une étude régionale du développement du potentiel inier est présentée puis détaillée pour quatre secteurs: Rouyn-Dranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des paramètres suivants: temps, méthodes de découverte, profondeur des gisements et poids métal. Les courbes cumulatives illustrant le nombre de gisements découverts fonction du temps montrent une forme générale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de couverte. Initiation, réalisation et stabilisation des cycles de décourté sont ainsi mis en évidence. Deux ""bourns miniers"", de 1922 à 1945 et de 1955 à 1965, rassemblent 72 % des mines identifiées sqú à présent.La plupart des mines sont trouvées en subsurface: 90% ont leur mmet entre 0 et 100 mètres de profondeur dont 70 % entre 0 et 10 êtres. Dans le temps, il y a d' abord récolte par prospection puis par ophysique et enfin, développement progressif du potentiel en proeur avec des méthodes composites. Environ 80% du poids métal extrait de 4 camps miniers, couvrant 8% de Ia surface régionale quelques gros gisements dominent /a production.Ces données permettent de proposer une nouvelle approche pour analyse d' une région minière:La distribution de Ia profondeur des gisements en fonction du temps est indicatrice de la maturité d' un camp minier et peut servir a évaluer son potentiel résiduel.L’analyse des courbes en ""S"" permet d’extrapoler les taux de succès relies aux différentes méthodes et met en relief le rôle crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1989

By M. Stogran-Baker, E. Legault-Seguin

"Fluorspar mining in the St. Lawrence area of Newfoundland and Labrador began in the 1930s and ended in the mid-1980s. In 2013, Canada Fluorspar (NL) Inc (CFI) discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods and began developing this resource. This paper discusses the flowsheet development of the AGS vein deposit. Testing at SGS began in 2009 with samples from other deposits in the area. The testwork included pilot-scale dense medium separation (DMS), laboratory-scale flotation tests to develop the flowsheet and a flotation pilot plant. The more recent work that is presented here has been devoted to the AGS vein, and included a variability testing program that gave tremendous insight into the metallurgical drivers of processing the deposit. The ore was found to be fairly variable in terms of fluorite grade, but also gangue mineralogy, which had greater implications on the DMS performance. The gangue mineralogy was also found to significantly impact the grindability characteristics of the DMS product. This paper will detail the testing conducted and the mitigating steps which were identified for the operation.INTRODUCTION Fluorspar is the industrial trade name for the mineral fluorite (CaF2), which is the primary industrial source of fluoride. There are a number of categories of fluorspar, most notably acid-grade fluorspar and metallurgical fluorspar (metspar). Acid-grade fluorspar has stringent specifications and is suitable for the production of hydrofluoric acid that is used for many applications. The typical specifications of acid-grade fluorspar are >97% CaF2 and less than 1% each of SiO2 and CaCO3, with a particle size distribution in the order of 80% passing 100 µm. Metspar is typically used for metallurgical purposes, typically as a flux in smelting, and has significantly more relaxed specifications (< 15% SiO2). The principle source of fluorspar in Canada has been from the Burin Peninsula in Newfoundland and Labrador. More than 3 million tonnes of fluorspar were produced there between 1940 and 1978 and from 1987 to 1990, when production ceased (Fulton & Montgomery, 1994)."

Jan 1, 2018

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By Jean-Marc Lulin

"Depuis 1906, pres de 130 gisements ont ere decouverts dans la inture archeenne polymetallique (Cu, Zn, Au, Ag) du nord-ouest becois. Une etude regionale du developpement du potentiel inier est presentee puis detaillee pour quatre secteurs: RouynDranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des parametres suivants: temps, ethodes de decouverte, profondeur des gisements et poids metal. ~~ courbes cumulatives illustrant le nombre de gisements decouverts fonction du temps montrent une forme generale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de ~ouverte. Initiation, realisation et stabilisation des cycles de decourte sont ainsi mis en evidence. Deux ""bourns miniers"", de 1922 a ~5 et de 1955 a 1965, rassemblent 72 % des mines identijiees squ' a present.La plupart des mines sont trouvees en subsurface: 90% ont leur fmet entre 0 et 100 metres de profondeur dont 70 % entre 0 et 10 etres. Dans le temps, il y ad' abord recolte par prospection puis par fphysique et enjin, developpement progressif du potentiel en proeur avec des methodes composites. Environ 80% du poids metal extrait de 4 camps miniers, couvrant 8% de Ia surface regionale quelques gros gisements dominent /a production.Ces donnees permettent de proposer une nouvelle approche pour lysed' une region miniere:La distribution de Ia profondeur des gisements en fonction du temps est indicatricede /amaturite d' uncampminieret peut servir a evaluer son potentiel residue/.L' analyse des courbes en ""S"" permet d' extrapoler les taux de succes relies aux differentes methodes et met en relief le role crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1990

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By E. Busse

"Heath Steele Mines Ltd. operates a lead-zinc-copper mining and milling complex in New Brunswick.• During the past seven years, as ore reserves increased, the mill capacity was first expanded to 1,600 tpd and then to 3,000 tpd. In the last expansion, instead of building a completely new 3,000-tpd mill, or adding to existing installations, Heath Steele retained service facilities, buildings, ore bins, Jab, etc., and removed and replaced almost all existing process facilities. Requiring a complete mill shutdown, the expansion had to be carried out in minimum time. Also, new equipment had to fit into existing space. Critical path networks of the project were prepared, a tight schedule for construction was mapped out and progress charted daily to detect problems before they could interrupt the schedule. Heath Steele supervised the purchasing, handling and storage of new equipment, maintained liaison with the engineering contractor and became a sub-contractor, using its own staff to install all flotation equipment and process piping. The 1,600-tpd installation was dismantled and a 3,000- tpd unit was successfully put onstream in 5 months - on time and within budget. One benefit stemming from the expansion: production increased 87 per cent while operating and maintenance labour rose only 8 per cent."

Jan 1, 1972

By Marcin Ziemski

This paper reports on an energy efficiency analysis completed as part of a research project looking at energy reduction opportunities in minerals processing operations. The plant discussed is a gold production facility owned by Newmont Gold in the Tanami region of central Australia. Due to its remote location, lack of nearby gas pipeline or power grid, the operation has been completely dependent on diesel fuel for its electricity generation and transport needs. The mine and processing plant use electrical power at a rate of 12MW to 18MW, resulting in a monthly electricity cost of over US$1.5M. The high cost of diesel combined with an impending power generation capacity shortage drove Newmont to undertake the energy efficiency study. An energy audit of the plant showed opportunities for significant energy savings through the strategic use of waste heat, fuel replacement alternatives and renewable energy sources.

May 1, 2007

By R. D. Brown

In the spring of 1977, Revenue Canada announced its intention to proceed in 1978 with a plan to impute a taxable benefit on interest-free and low-interest loans provided to employees. Such loan arrangements are often an important aspect of the compensation packages provided by many companies to their employees. Since the original announcement, there have been many submissions to Revenue Canada opposing this change, and the Finance Minister has now brought down a compromise solution with the introduction of a proposed amendment to the Income Tax Act. The amendment, which would not take effect until the 1979 taxation year, would require an employee, a shareholder or a related person to include a benefit in income measured as the difference between the interest on any such loan computed at bank prime rate and any interest actually paid. Only the amount of such a benefit in excess of $500 in a particular year would be required to be included in income. Of particular interest is the exclusion from these benefit rules of loans up to $50,000 in respect of the purchase of a house on the relocation of an employee and loans provided for the purchase of shares of an employer corporation.

Jan 1, 1978

By N. T. Oo, L. D. Hutton

"The Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. A site specific rock classification system was developed that characterised all the rock units based on the engineering properties governing the rock mass behaviour i.e. intact rock strength and defect characteristics (spacing, aperture, infilling, wall roughness and weathering) irrespective of the geological origin. This approach simplified the design and the on-site verification processes. Based on this classification system, rigorous quantitative statistical assessments of the available geological information including various laboratory and field testing were performed to derive the geotechnical design parameters for various rock classes. These parameters were used to complete geotechnical designs of retaining wall systems. INTRODUCTIONThe Banora Point Upgrade Project is a 2.5km long six-lane divided freeway in northern New South Wales, Australia. The key features include two interchanges, a 300m long viaduct, a large cutting through Sexton Hill with an associated 100m wide Land Bridge and retaining walls reaching 490m long and up to 22m high. This paper focuses on the derivation of representative geotechnical parameters for geotechnical design of the retaining structures supporting Sexton Hill Cutting including bored pile retaining walls and soil nail walls. The geology at the project area comprises a volcanic succession of variably weathered basalt flows and agglomerate deposits that reach 48m in thickness and overlie Mesozoic sedimentary rocks. Due to the complex geological nature of the site, an understanding of the regional and local geology, the typical behaviour of individual geological units and the implication of onsite variations from design intention are the ultimate challenges to the geotechnical engineer in order to select representative geotechnical parameters for design."

Jan 1, 2015

By A. D. Yell

"Recovery of water is always a major factor in the Beneficiation process. As Preparation Plants become larger the recovery of water for reuse, is a critical cost consideration. Tema Isenmann Inc in conjunction with our sister Company Multotec Manufacturing, has over the years, developed numerous different Screen Panels, Sieve Bends and Static Screens for dewatering. This paper will focus on a new innovation, the TeePee™ Panel which has double the open area of conventional Screen Panels. This results in efficient dewatering (reduced filter cake moistures) which allows for the use of smaller Vibrating Screens or increased capacity on existing Vibrating Screens. A major factor in the efficiency of any Screen Panel, including TeePee™ Panels, is the performance of the Vibrating Screen. If the Vibrating Screen does not have the required gravitational force or screen area to drain it will not dewater efficiently. Therefore a holistic approach has to be taken where the Vibrating Screen needs to operate at an optimal level, in conjunction with the correct Screen Panels, to achieve efficient dewatering. Key performance areas for Vibrating Screens are therefore detailed in this paper with an emphasis on important dewatering criteria. Case studies of different dewatering applications are included, where the use of TeePee™ Panels, has shown a marked improvement over conventional flat Screen Panels in reduction of filter cake moisture content.INTRODUCTION Dewatering can be done in a number of different ways and is largely dependent on the ore type, the particle size distribution and to what extent one needs to dewater will determine the method used. There are a number of different dewatering methods that can be used for particles above 200 micron, including Screen Bowl Centrifuges, Filter Presses, Static Screens, Static Sieve Bends and Vibrating Screens. This paper will focus primarily on Vibrating Dewatering Screens showing improved drainage and a reduction in the filter cake moisture content. KEY PERFORMANCE CRITERIAL FOR VIBRATING DEWATERING SCREENS For clarification the critical key performance criteria for Vibrating Dewatering Screens are set out in this paper. Dewatering Screens Vibrating Dewatering Screens are normally linear motion, either horizontal or inclined at 5 to 7° upwards with a vertical or back sloped plate at 45° to the rest of the screen deck. The back plate will often have screen panels in them to increase the dewatering capability, as shown in Figure 2 below."

Jan 1, 2017

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989

By D. R. Derry

"IT WOULD TAKE a braver man than I to try to forecast the future of mining exploration far into Canada's second century. Even to look ahead ten or twenty-five years we must review the figures of the fairly recent past -and I have found this quite a time-consuming but interesting job -in order to find trends and project them into future years. The trends to which I will refer are: firstly, the annual expenditure on exploration and its relation to value of output; secondly, the discovery rate and its relation to production initiations; and thirdly, the methods by which discoveries have been, and will be, made. Exploration Expenditures Figures on the annual expenditure on mining exploration in Canada have been collected and published for some years by the Do-minion Bureau of Statistics. These have some unavoidable limitations; e.g., in the varying definition between one company and another of what comprises ""Exploration"" and in the difficulty of getting complete returns. However, although the actual figure for a given year may be subject to question, I believe that the relative figures from one year to another are reasonably reliable. There is also a lapse of time between the collection of data and publication -the last published figures are for the year 1963. In bringing the figures up to date to 1966 I have canvassed eight of the larger mining and exploration companies and obtained their figures for 1963 to 1966 inclusive, and then averaged these for each year and applied the progression to the 1963 figures."

Jan 1, 1968