Search Documents

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

By K. B. Culver

"This paper provides background information on the expansion programs of Rio Algom Limited at Elliot Lake. Included are details on the Quirke expansion program, the Panel mine rehabilitation program, including the selection procedure for the tailings containment area, the Stanleigh mine rehabilitation program, housing, government regulations and the Environmental Assessment Board hearings. Introduction After 2Y2 years of public hearings, 4 years of arbritrating differences of opinion between our engineers and government licencing authorities, interspersed with research into radium removal and development of the LAMIX process and carrying out the work associated with some 24 control orders issued to us by the MOE, it is very difficult to compress all of the experiences and frustrations into a single paper. The highlights, as they relate to the expansion programs of Rio Algorn Limited and its affiliate, Preston Mines Limited, will be covered. Denison Mines Limited, of course, is the other uranium producer in Elliot Lake. They are currently in the process of expanding from 7,000 to 11,000 TPD by the second half of 1980 and then to 15,000 TPD by the mid 1980's. In giving this overview, the following seven items will be discussed: • The basis for Rio Algom's and Preston's expansion plans. • The Quirke Expansion. • The Panel Rehabilitation. • The Stanleigh Rehabilitation. • Housing Programs. • Government Licencing Requirements. • Environmental Assessment Board Hearings."

Jan 1, 1980

By J. T. Kalala

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By C. E. Rodgers

WHEN the writer was engaged early last year by Canadian Comstock and its subsidiary, the Metropolitan Electric Company, to act as Consulting Mining Engineer in connection with the layout and equipment of the new ore-dressing laboratories at Laval University, Quebec, the metallurgical laboratory section of the School of Mines building was completely erected, including plastered walls, partitions, etc., and finished concrete floors. At that time, however, no equipment had been ordered, except three Dominion ball-mills and two Bell screening machines. ADVANCED OR CONTINUOUS LABORATORIES The continuous laboratory section of the Department occupies the basement and three floors of the building, with an approximate floor area of 9,000 square feet. Because of limitations imposed by the design of the building (height and arrangement of rooms, strength and design of floors, etc.), modifications of layout from what otherwise seemed most desirable were, of necessity, made. These included: (a) Omission of automatic sampling of the dry ore. (b) Complete elimination of inclined belt-conveyors through floors. (c) Exclusion of bucket elevators for either dry or wet ore transfer. (d) As a substitute for grill-covered drains and floor sumps, drainage from sections or from individual pieces of equipment was piped to a disposal system in the basement. (e) Substitution in several instances of fabricated steel in place of the usual concrete foundations for machinery. (f) Reducing floor cutting and area of such opening to a minimum. Ore storage and chute capacity above the basement level was also minimized to reduce total weight.

Jan 1, 1941

By John T. Whetton

"FROM 1850 when the annual production was around 50 million tons, coal output in Great Britain expanded rapidly to 225 million tons in 1900 and 287 million tons in 1913. However, during the First World War, countries which had previously bought large quantities of coal from Britain sought other sources of sup-ply or developed their own coal re-sources. Thus from the record figure of 73 million tons exported in 1913, Britain's coal exports declined until in 1938 they stood at 39 mil-lion tons. An important reason for this was the development of oil engines for marine propulsion. Today, nearly all the navies and mercantile shipping in the world have turned to oil engines. Sometime in the future, however, it is reasonable to expect nuclear power to replace oil.During the Second World War, coal output in Great Britain and manpower at the mines were reduced considerably and in 1.945, 175 mil-lion tons were produced by 709,000 miners. Exports were meagre, only 8.""7 million tons went to foreign consumption. During the severe winter of 1947, inland demand for coal exceeded production and exports were prohibited. Even importation of coal was required to meet inland demand. These were years when the coal industry of Great Britain made immense efforts to secure maximum output irrespective of economy. The energy needs of Great Britain appeared insatiable; but had it been possible to export, the nationalised mining industry could have made huge profits as there was a world shortage of coal. However, home needs were considered to be the priority and many overseas markets were lost. Other producers moved in and secured long-term contracts. Not only was the British export market lost, but also the nationalised industry had to sell the imported coal at the same prices as home-produced coal and suffered losses up to of:3 per ton. Bence, at a time when the National Coal Board might have ac-cumulated a reserve fund to cope with less prosperons times, it was having to spend large sums of money securing sufficient coal for inland consumption. This was a time when intensive efforts in the mining industry, comparable with those of many industries and establishments inclusive of the armed services during the war, would have produced a greater amount of coal and have been of immense value to the country as a whole."

Jan 1, 1960

By Robert Lee

"International competition is presenting the Canadian steel industry with a major challenge. While Canadian companies have invested in new technology, research and development, activity by Canadian industry, in general, lags significantly behind that of its major competitors. While OECD countries increased their research and development spending during the 1980s, Canada's R&D funding levels have changed little since the early 1970s and have actually dropped since 1986, despite greater public discussion on the issue. This fact is reflected in the relatively slower pace of innovation in the Canadian steel industry, despite the efforts of both government and industry.In addition, there are a number of factors that undermine the competitiveness of the Canadian steel industry, in particular in relation to the United States. Among these are higher interest rates, labour costs and tax rates, as well as an overvalued Canadian dollar. Canadian steel companies are thus feeling the full impact of the current economic recession. This recession, combined with recent strikes, have, for example, caused serious losses for Algoma and Stelco.In spite of these objective difficulties, the Canadian steel industry has been able to survive and continues to strive for a leadership position in the world market. Since World War II, heavy investment in new technology has allowed the industry to upgrade its facilities and increase productivity, while at the same time improving quality and reducing pollution. This last point is particularly important in view of public insistence on improvements to the quality of the environment. Over the next decade, this technological innovation must be maintained and intensified if industry is to meet the challenge of international competition and attain a leadership position."

Jan 1, 1991

"A method is described for determining the viability of hard rock orebody extraction by block caving. Using a very limited amount of geotechnical data, the procedure enhances Laubscher’s empirical stability graph method by using the complex structural modelling system (ChaSM) to assess cavability and block cave tonnages.IntroductionIn considering the selection of suitable mining methods, block caving has gained popularity over other extraction systems in recent years (Butcher, 1999). This has been ascribed to the fact that block caving is the lowest cost per ton mining method, with orebodies that were in the past considered unsuitable for caving, now being successfully mined. However, even though all orebodies will cave, a problem exists in the evaluation of economic viability — it is necessary to be able to predict both when the orebody will cave and what will be the sizes of the initial ore fragments (and the associated tonnages) that report to the drawpoints. This problem is compounded by the fact that, during the scoping study phase of a project, only limited geotechnical data may exist on which to base an assessment of whether block caving is viable or not. Empirical and numerical methods of cavability assessment do not account for the full effects of geological discontinuity trace lengths, nor for the stress regime. Those require significant geotechnical data to be available. The result is that uncertainty may exist as to whether block caving is an economic option. This uncertainty is complicated by the fact that limited experience exists with the caving of more competent orebodies.This paper describes a method for assessing cavability, and for predicting the size of initial ore fragments and the tonnages reporting to block cave drawpoints, using only the level of data normally available during a scoping study. Fragment size and tonnages are assessed by identifying potentially unstable blocks and wedges in the undercut back using statistical joint data. The effects of lateral confining stresses are accounted for by comparing the in situ stress orientations with the joint orientations. To evaluate the accuracy of the method, a back analysis exercise was conducted to predict cavability and initial tonnage for a mine in which the actual behaviour is known. The method is then applied to cavability and tonnage predictions for a hard rock orebody."

Jan 1, 2002

By Paul Hughes

Purpose of Research ? What are the loading mechanics of paste against barricades? ? What is the capacity of the composite paste fill fences? ? Based on the loading mechanics of the paste, do the fill fences pose a risk of failure? Outline ? Glossary of Terms ? General Introduction ? Research Methodology ? Site Description ? Instrumentation Program ? Results ? Analysis ? Conclusions ? Recommendation for Future Work

May 1, 2008

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By F. McCarthy, R. McDonald, G. Woodbridge, G. Brock, D. Robinson

"The Direct Nickel process is a hydrometallurgical technology being developed to treat nickel laterite ores by leaching at atmospheric pressure. The leaching process uses nitric acid in a relatively large excess, is thus non-selective, and much of the soluble iron goes into solution. The first stage of solution purification is iron hydrolysis and the Direct Nickel process utilises the colligative properties of the pregnant leach solution (PLS) to enable the removal nitric acid of varying concentrations via distillation. Once sufficient acid has been removed, the boiling point of the solution is increased allowing high temperatures (up to ~170°C) to be achieved under atmospheric pressure. The higher temperatures initiate the precipitation of the iron primarily as hematite and allow the removal of the acid generated by the hydrolysis reaction. The rejection of the iron is near complete with solution tenors typically falling from 65 g/L Fe, or more, to less than 50 mg/L Fe. The separation of clean nitric acid from the PLS at this stage allows for relatively simple acid recycling. A hematite product with iron content above 60% could also provide an extra revenue stream.INTRODUCTION The Direct Nickel (DNi) Process is a novel hydrometallurgical processing route designed to treat all types of nickel laterite ores in a single flow sheet using nitric acid under atmospheric conditions. A simplified flow sheet is shown in Figure 1.Between 2007 and 2012 the process was developed and refined at Direct Nickel’s laboratory within the CSIRO Minerals’ facilities in Perth, Australia, and in 2013 a series of pilot plant trials were run under continuous operating conditions. The process is designed to treat both limonite and saprolite in the same flow sheet, and after comminution, the blended ore is mixed with nitric acid and leached just below boiling point in agitated atmospheric leach tanks. The acid is added in excess, so typically for a blend of limonite and saprolite the acid addition can be in the order of 1.8-2.0 t acid/t dry ore. After a residence time of between 4-6 hours the majority of the soluble metals have leached into solution and the insoluble leach residue is separated from the pregnant leach solution (PLS) via counter-current decantation."

Jan 1, 2016

By Richard J. Wardle, Ambrose F. Howse

The industrial minerals industry in Newfoundland and Labrador is a significant contributor to the provincial economy. The variety ofcommodities produced reflects the diverse geological environment from which they come. A highlight of the past decade has been the continuing development of dimension stone quarries, with producers now active in anorthosite, gabbro, granite and sandstone. Other dimension stone prospects have been identified and are in various stages of assessment and development. Western Newfoundland hosts a large resource of limestone, dolomite and marble. It provides raw material for industries that produce Portland cement, agricultural limestone and aggregate, as well as chemical-grade limestone and dolomite products. In western Labrador, dolomitic marble is quarried for use in the production of self-fluxing iron ore pellets. The recent opening of a new gypsum quarry at Fischells Brook signalled the beginning of a new era in the commercial production ofgypsum, a commodity which the province has produced since the 1950s. Hopefully it will emulate the nearby Flat Bay Quarry (now closed) which was a long-time exporter to markets along the U.S. eastern seaboard, in addition to supplying local demands. Oil production and continuing exploration in the Newfoundland offshore has renewed interest in local barite deposits for potential use in drilling fluids. Already there has been some production from the Collier Point deposit, and at Buchans, an existing plant is being refurbished to recover barite from a large tailings pond. Emerging new industries include the development of an antimony mine in central Newfoundland, the development of silica deposits near Labrador City for silicon metal production, and reactivation of the St. Lawrence fluorspar mine. The province has many deposits with development potential such as rare metals at Strange Lake, white marble at Roddickton and salt deposits near St. George's Bay region.

Jan 1, 2001

By w. w. Fraser

"In late 1985, Hudson Bay Mining and Smelting Co., Limited announced the Namew Mine/Mill project. Environmental baseline monitoring and planning began in early 1985 while a major drilling program was under way to delineate the ore deposit. This paper overviews the environmental assessment work conducted for the mine/mill operation, and outlines the tailings and water management practices.Planned environmental works and approach were affected in late 1988 when a massive water problem was encountered in the mine. The requirement to depressurize the rock surrounding the underground workings led to the need to develop, on short notice, an environmentally-acceptable procedure to dispose of a large volume of slightly-saline water.Biological toxicity tests performed on the depressurized effluent proved the effluent to be non-toxic and thus allowed resolution of the disposal problem. This resolution includes the conversion of a large water body from native fish species to a rainbow trout fishery."

Jan 1, 1991

By H. R. Butler

"The Ontario Division of Inca Metals Company, a Unit of Inca Limited, operates eleven mines, four mills, three refineries, one smelter and one iron ore recovery plant. All but one mine, mill and refinery are located within a fifty kilometer radius of Sudbury, Ontario. A mine-mill complex is located some 100 kilometers west of Thunder Bay on the shore of Lake Shebandowan and a nickel refinery at Port Colborne.During the past 10 years the use of recycled water in our milling operations has increased to more than 95% at each mill. This high degree of water reuse has reduced the (a) need for fresh water and (b) the contaminant level of the downstream aquatic environment. The aggregating of effluents in a common receptor provides a process water having a consistent quality thereby minimizing upsets in mill metallurgy while concurrently improving the operating economies and the downstream aquatic environment."

Jan 1, 1980

By Robert B. Parsons

"Originally intended to be implemented in 1977, but actually introduced effective May 6, 1974, the earned depletion regulations have been substantially refined and modified since their appearance on the Canadian tax scene, so that this important legislation now consists of a highly complicated set of rules which even the most astute follower of tax law has considerable difficulty sorting out!This month, Tax Notes attempts to cut through this bewildering array oj regulations, in reviewing the main features of the earned depletion allowance applicable to mining operations. Despite the phase-out of earned depletion allowances for most oil and gas operations as part of the federal government&apos;s new National Energy Program, earned depletion provisions are still alive and well for the mining sector, although they might well be slowly strangling to death in their own entanglement of complexity!"

Jan 1, 1981

By Edward Sampson

Bases of National Power At a time when the economy of the world is in a particularly troubled state it is appropriate to examine some problems of the distribution of natural resources. I should like particularly to call attention to the remarkable increasing demand for natural resources, to give an analysis of the demand for certain mineral resources, and to direct attention to some problems in satisfying this demand. All industrial power is based on natural resources and the most basic of these are soils, energy resources, and mineral resources. There is a strong interrelation of these resources, more than is obvious, and I shall take up certain aspects from the point of view of a geologist. Few nations are well endowed with all three of the kinds of natural resources I have mentioned and much has been done by some small countries whose peoples are industrious and enterprising and where conditions for free world trade have been favourable. However, major industrial power is dependent on a substantial endowment of all three classes.

Jan 1, 1949

By Wayne N. McKee, Scott A. Lewis

"Introduction to the Syncrude OperationSyncrude Canada Ltd., located 42 km north of the city of Fort McMurray, Alberta, (Fig. I) is an integrated operation that has produced synthetic crude oil from the Athabasca oil sand deposit since 1978.The operation, consisting of a surface mine, an extraction plant, a bitumen upgrader, and a utilities plant, is currently capable of producing over 60 million barrels of crude oil per year. Production is expected to increase to 70 million barrels of crude oil per year over the next five-year period with no major changes to equipment or process planned.The Syncrude surface mine, producing a total of 675 000 tonnes of ore and waste per day, rates as one of the largest mines in the world. A strip mining method is utilized, with two or three operating benches necessary to excavate a total depth varying between 60 m and 70 m. The 20 m to 30 m of overburden is removed by electric and hydraulic shovels and 200-ton haul trucks, and dumped in the mined-out pit for final storage. The overburden operation creates a flat bench near the top of the ore zone on which the four 60 m3 draglines operate. The draglines excavate interbanded ore and waste in the highwall, with ore placed on the operating bench in windrows, and waste returned to the mined-out pit. The windrowed ore is reclaimed by four bucketwheel reclaimers, and discharged onto a conveyor system for transfer to the extraction plant."

Jan 1, 1993

By Xiong Tong, Jiushuai Deng, Yingbo Mao, Lingyun Huang

Ammonium carbamate has been used as a reagent for the leaching of copper from the copper oxide ore found in the Honghe state, Yunnan province, China. In order to find the optimal conditions for the leaching of copper from this copper oxide ore,the effects of several processing parameters, including the concentration, time, temperature, particle size and stirring intensity have been investigated. The results of these optimization experiments showed that the leaching rate of copper reached up to 72.76% under the following conditions: liquid-to-solid ratio of 10:1, ammonium carbamate concentration of 2.5mol/L, leaching temperature of 45 °C, stirring speed of 300rpm, a reaction time of 1.5 h and 85% by weight thereof passes through a sieve having 0.074 mm.

Jan 1, 2015

By G. F. Raymond, W. P. Armstrong

"At the time of this study, the Valley mine was producing 23 000 tonnes of ore per day from a large, low-grade porphyry copper orebody. Sulphide mineralization, principally bornite and chalcopyrite, occurs in a stock work of quartz veins in one phase of the Guichon Creek batholith. The property was explored from 1967 to 1982, and was placed in production in 1983.Using a three-parameter lognormal approximation developed by G.F. Raymond at Similkam een and Mount Isa Mines, a geo- statistical conditional probability ore reserve was estimated prior to mining. Comparisons with blasthole kriging and milled ore for the first 17 months of production showed close agreements at all cut-offs between conditional probability estimates and mineable ore. This was not true of either kriging or polygon estimates. An important part of this work was identifying and correcting for bias in both exploration and blasthole samples.IntroductionCominco&apos;s Valley lake deposit is a large, low-grade, porphyry copper orebody in the Highland Valley of British Columbia. Total indicated plus inferred ore reserves are 700 M tonnes at ore grade of 0.47070 Cu. At the time of writing, ore milling is at a rate of 23 000 tI d through the old Bethlehem mill. Mining is in 10m horizontal benches using 9.8 m3 shovels and 90 tonne trucks. Since this paper was written, Valley and nearby Lomex have been combined into Highland Valley Copper with a combined oreproduction of about 120 000 tI d.Copper mineralization, principally bornite and chalcopyrite, is regularly distributed throughout the deposit as disseminated low-grade within a granodiorite host rock, and as higher grade veinlets within a stock work of near-vertical quartz veins generally 10 cm or less in width. It is likely that problems with sample variability and sample bias are mainly related to mineralization within quartz veining. Valley geology has been described in detail by Allen and Richardson and by Osatenko and Jones (2). The exploration sampling program and identification of diamond-drill sample bias have been discussed by Armstrong and Newman&apos;»."

Jan 1, 1988

By G. G. Richards, Y. Oyediran, V. Chow

The oxygen softening process for partial removal of arsenic and antimony from lead bullion has been in use at Teck Cominco&apos;s Trail smelter since 1986. In this process, industrial oxygen is injected into bullion to remove As and Sb with the formation of an oxide slag. In Trail, the levels of these elements are reduced to concentrations suitable for processing in the Betts electrorefining plant. Recent moves toward the treatment of higher arsenic-bearing feeds have necessitated an increase in the process capacity to meet the specifications for drossing plant bullion. Process intensification trials were conducted in-plant to develop an operating strategy for higher bullion processing rates. This was preceded by a study conducted with McGill University to develop a fundamental understanding of the therm ochemistry and kinetics of the process. The results have yielded more effective control of the operation, and identified opportunities for further improvements.

Jan 1, 2008

By Brad Gunn

Our program has been dictated by the necessity of broadening our markets through converting potash chemicals to fertilizers more in demand than potassium chloride. To this end, we have undertaken studies on methods of preparing potassium sulphate or potassium magnesium sulphate by rather simple conversion. When mixtures of sodium and magnesium sulphates are reacted with potassium chloride, the ratio of sodium to magnesium is quite pertinent. A range of ratios has been selected and the conversions of potassium chloride to sulphate have been assessed by cyclic operations. Results from experimental procedures for producing potassium nitrate are also avail-able. The influence on recovery for systems including organic solvents is assessed for a variety of situations.

Jan 1, 1971