Search Documents

By L. D. Eccleston

Any man-made structure will eventually decay, but we are basically concerned with the prevention of corrosion within a fairly limited time span. How corrosion can be minimized by design, the removal of oxides and a careful choice of paint systems is discussed, and mention is made of the electrical nature of most anticorrosive systems. Also discussed are the characteristics of certain paint binders and how mechanical properties will differ for various environments. Corrosion of a substrate by acidic breakdown products of some paints is mentioned in conjunction with a discussion on convenience versus ultimate performance. A brief mention is made of the three main components of a paint system, and the principal types of paint are placed in broad categories, with the main strength and weaknesses of each type listed.

Jan 1, 1979

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

This paper proposes a classification model to predict the split coefficient of gold ore particles as a function of the particle size and gold content. The model is calibrated and validated using data obtained from the sampling of an industrial grinding circuit. Model calibration is based on a complete simulation of the circuit and involves parameters related to the gold grain distribution in the ore as well as a grinding and liberation model. Since cyanide is added into the studied grinding circuit, assumptions related to gold dissolution in the mills are made to allow simulation results which reflect industrial behaviour patterns.

Jan 1, 2011

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By J. R. Jutras, C. Brissette, J. Champagne

"Pure cadmium sulphide was leached by the action of the bacterium Thiobacillus thiooxidans in the presence of finely divided sulphur. The influence of time, temperature, pH and concentration of inoculum on the extent of the cadmium extraction was studied. Under optimum conditions, up to 72 per cent of the cadmium could be dissolved over a six-week period. A cursory study of the role played by elemental sulphur seems to indicate that its presence is essential but that the sul1>huric acid produced through its oxidation is a minor factor in the cadmium extraction."

Jan 1, 1971

By H. Kudelka

Copper electrowinning at Duisburger Kupferhuette was introduced in March 1975. The electrowinning plant has a capacity of 10,000 mT of copper cathodes a year. The cuprous oxide feed material is an intermediate product of the treatment of the leach solutions, originating from chloridizing roasting of pyrite cinders. This material is characterized not only by a wide spectrum of accompanying impurities, but also by an unusually high level of precious metals. As the priority set was the production of high-purity cathodes. there was a need for developing a process which would be suited to treat complex leach liquors . The process adopted consist s of an oxidizing leach in spent electrolyte, followed by two- stage purification, By this means. a low- acid pregnant copper electrolyte is obtained free of elements detrimental to copper quality. Electrowinning is carried out at a current density of 200 A / m2 in the presence of 10 g/l zinc. The electrowon copper has a conductivity of at least 101.4% lACS and a softening temperature not exceeding 200°C, which makes it a suitable product for continuous casting and dip ?forming.

Jan 1, 1977

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By Staff

"The Weyburn Oil Field, located 80 miles southeast of Regina, Saskatchewan, was discovered by Central-Del Rio Oils Limited, in January, 1955. As of January 1st, 1959, the field had 357 wells capable of producing an estimated total of 45,100 barrels of oil per day.Highly portable, economical, drilling rigs are used to penetrate the pay at a depth of 4,400 to 5,100 feet. Presently, the complete drilling operation for an average field well, including drilling, coring, testing, and running casing, requires 12 days. Drilling procedures are conventional for a field of this depth and no serious problems exist. Central-Del Rio core the productive section of all their wells, which provides valuable information for well completions and reservoir studies. Production casing procedure is to set through the zone and perforate the productive inter-val. This was found advisable due to the lensing nature of the porosity and permeability throughout the reservoir, and to the high connate water saturation encountered in the tighter sections of the reservoir in the north and northeast areas of the field.Although a few wells in the field have produced naturally by flowing or pumping without acid treatment, it has generally been necessary to acidize the wells to make them commercial producers. To date, acid treatments appear to effect better stimulation of the limestone reservoir than fracturing treatments. Perforation sealing balls have been used as an aid in selectively treating all of the perforated interval.The majority of the field is on pump, producing at a low gas-oil ratio. The main part of the field has water-free production, with most of the water being produced in the north and northeastern area. Salt-water disposal is now available in the field through two disposal wells completed in the Basal Blairmore sand.The Midale Beds ""Marly"" and ""Vuggy"" zones form the principal reservoir, which is a stratigraphic trap, with the north and northeast edges terminated by a porosity and permeability pinch-out and the south-west and west edges bounded by water-laden porosity. There is no evidence to date of a gas cap. The reservoir apparently is producing on a fluid-expansion-type mechanism. The increasing water production in wells on the southwest and west edges of the field indicated water encroachment from these directions, and suggests some recovery energy may be available from this source.The total probable ultimate remaining recoverable reserves have been estimated at° 332,469,000 barrels of oil. Markets have not been able to keep up with the rate of development of the medium crude re-serves. However, it is felt strongly that substantial additional markets for Weyburn medium crude will be developed by the producers in the near future at realistic wellhead prices."

Jan 1, 1959

By I. R. Muirhead, A. L. Craven

The trend in mining thermal coal is only to mine coal with the lowest sulphur content. In many coal seams, bands of coal with high sulphur content are often present, generally occurring either at the roof or floor level. Methods of selective mining are, therefore, necessary to recover only the low sulphur coal. This paper examines the methods currently in use in mines and the alternative methods that are able or have potential to offer control of shearers and continuous miners where greater thicknesses of coal have to be left in the roof and floor. These alternative methods rely on such characteristics as neutron gamma radiation; electromagnetic waves; vibration; infrared; infrared; optical; pick force; X-ray fluorescence; conductivity; gyroscopes and laser systems.

Jan 1, 2000

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By Earle J. Klohn

"The design, construction and operation of tailings dams is rapidly becoming a major consideration for most new mining developments, as well as for many existing operations. In North America, under pressure from public opinion, various government agencies have in recent years enacted legislation covering the design, construction and operation of tailings dams. In British Columbia, comprehensive legislation has been passed during the past year (1971). All of these new regulations may be placed into two broad categories: regulations concerning the safety of the dam and appurtenant structures, and regulations concerning the prevention of pollution. Both types of regulation affect the design of the tailings dam facilities. Consequently, they must be considered jointly by the designer. A good tailings dam design must satisfy the basic requirements of safety, pollution control, storage capacity and economy. To achieve this, 'the design must be based on a thorough understanding of both the geotechnical problems involved and the requirements of the mining development. Obviously, this requires close cooperation between the designing geotechnical engineers and the mining operators. This paper outlines the major engineering factors that should be considered in the investigation, design, construct ion and operation of tailings dams. Basic methods of tailings dam construction are reviewed and the advantages and disadvantages of each briefly discussed. Comparisons are made between the design and construction of conventional water supply dams and tailings dams. Examples are presented of some of the problems that may arise during construction and operation of a tailings dam. The paper also explains the need for basic instrumentation of tailings dams and for carrying out simple field tests and measurements during construction and operation. Of prime importance is the downstream monitoring of surface and subsurface seepage flows. These observations are invaluable where contamination of surface and/or subsurface water may become a contentious issue at some future date. Each tailings dam design must be based on a study of the particular requirements of that project. To make a proper evaluation, adequate data must be available concerning a large number of items•, including such things as: topography, hydrology, geology, subsoil properties, seismicity, government regulations, fineness of mill grind, mill water balance, availability of suitable construction materials, volume of water to be stored behind starter dam, downstream development or liability, and many others. The large number of variables involved in such an evaluation often result in the designer considering two or more alternative designs. Selection of the final design, which is usually based on detailed cost analyses of the alternatives, must be made in close consultation with the owner."

Jan 1, 1972

"Real time analysis of conveyed bulk materials can be used to improve process performance by reducing variability and upgrading ore quality through selective removal of increments of flow that do not meet appropriate selection criteria. This paper focusses on proven Prompt Gamma Neutron Activation Analysis (PGNAA) and microwave transmission technologies used to representatively measure conveyed ore quality in real time so that meaningful decisions can be made between the mine and mill. This enables the effective removal by bulk diversion of small increments of conveyed flow such as waste, highly deleterious material or sub-economic material from the mill feed. Improved ore quality in plant feed optimises process performance, reduces processing costs and minimises tailings generation. Analysis is unaffected by particle size, dust, layering or segregation, mineralogy and belt speed. Technologies are explained and performance examples given from installations in copper and iron ore. The technology has been used successfully in bulk sorting for over twenty years typically using measured increments of a few minutes. Improvements in technology and calibration performance have resulted in accurate measurements over increments of thirty seconds and below.INTRODUCTION Ore quality variability exists on a number of scales. Block model grades represent a few hundred to many thousands of tonnes. Grade control at the mine occurs on a scale typically down to the size of a haul truck, which may be a few hundred tonnes. Highly variable ore quality is detrimental to process efficiency and effectiveness. Processing waste or low grade ore when higher quality feed is available represents a lost opportunity to generate higher revenues earlier in the operational life. Measuring ore quality accurately over short time increments during conveying enables small increments to be measured and diverted according to their quality. The paper explains the technology and benefits. Neutron irradiation techniques were considered potentially suitable for conveyed bauxite measurement by Beurton et al, 1995. Tran & Evans (2001) concluded there was no equivalent technology to Prompt Gamma Neutron Activation Analysis (PGNAA) in terms of material penetration power. PGNAA was evaluated by Nelson & Riddle (2003) for possible use in the phosphate industry and recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control. Cottle (2007) discussed test work for an iron sinter application and Delwig et al (2011) described the successful installation in 2009 and performance of PGNAA for base-to-acid ratio control in sinter feed with the analyser output used to control lime addition. Geoscan (PGNAA) works very well on iron ore and can “improve control over what is happening in the plant” and that comfort can be provided in knowing that the product is on-spec according to Minnett (2010). PGNAA is not yet used in the minerals sector for tariff purposes as has occurred since 2000 with Coalscan (PGNAA) in coal (Minnett, 2010)."

Jan 1, 2017

By W. A. Gow, H. H. McGreedy

It is believed that many of the problems encountered in the operation of gold cyanidation plants are difficult to resolve due to the lack of sufficient and reliable in-formation regarding the variations and actual values of operating variables at any given time. The application of instruments to monitor the more important variables in the cyanidation process should result in more efficient plant operation and a better understanding of the process. The use of pH and conductivity sensing devices for alkalinity measurements, a monitor to determine the dissolved oxygen content of plant solutions, a continuous cyanide titrator and sonic control of grinding circuits are discussed. Although the discussion is oriented toward the cyanide process, much of the paper is applicable to other ore treatment operations.

Jan 1, 1966

By L. C. Stevens

The particular purpose of this paper is to direct attention to the development of underground conveying as applied to methods of working coal in the mines of Alberta. Historical A retrospective view of coal mining discloses a continuous effort, on the part of those interested, to substitute mechanical contrivances for hand labour. A patent for a coal-cutting machine was granted to Michael Menzies in 1761, at which time much of the transportation of coal underground was accomplished by means of sledges. Early forms of cutting machines attempted to duplicate the action of a miner&apos;s pick, and one hundred years lacer than Menzies? patent we still find this class of machine, driven by water power or compressed air, in use to a limited extent. A coal-cutter using the principle of a circular saw and worked by hand was exhibited in London in 1851, and from these crude beginnings the machines of today have been evolved. Transportation of coal underground has similarly been subject to considerable improvement. The above mentioned Michael Menzies took out a patent in 1750 covering the use of a self-acting incline plane, which is probably the earliest record of any system devised to lighten the load of the crammer or car-pusher of those days. In the year 1868 the Gillot & Copley machine was patented, this being a compressed-air-driven disc coal-cutter which proved highly successful. The chain cutters were a natural development from this type, and for a number of reasons they have been even more successful in the majority of cases.

Jan 1, 1930

By G. W. Evatt

This paper presents the scientific framework underpinning the Resource Valuation and Optimisation Model (RVOM). The RVOM is a Real Options software package, which helps mine owners optimally plan their operations, understand their project risks, and make defensible valuations. This is achieved in the presence of both financial and physical uncertainty. The three key outputs from the RVOM are: Valuation, Optimal Decision and Probability of Decision, where a decision can include any combination of: normal operation, expanded operation, care and maintenance, and abandonment (and variants thereof). This paper presents a clear example of the RVOMs usage to a case-study gold mine.

Jan 1, 2011

By D. Yuan, L. Yan, M. J. Collins, P. Kalanchey, I. M. Masters

ABSTRACT Pressure oxidation tests have been conducted by Sherritt for a refractory gold-silver project in China. The feed contained 39 g/t Au and 970 g/t Ag; the major gold-bearing minerals were pyrite and arsenopyrite. Because the feed contained a significant amount of silver, which can be refractory to cyanide leaching after pressure oxidation due to the formation of argentojarosite, the test program included investigation of methods to enhance silver recovery. The “lime boil” process proved successful and was incorporated into the flowsheet. Gold extraction from the lime boil product solids was 95–98%; silver extraction was up to 94%.

Jan 1, 2013

By J. E. Hawley

Introduction The Siscoe gold mine is the most easterly producer of gold from deposits lying in the belt of Keewatin and Timiskaniing rocks which extends east from Kirkland Lake, Ontario, and on through the Rouyn copper area. Unlike many of the deposits in this belt, those of Siscoe are contained almost entirely in a stock of much-altered granodiorite which intrudes Keewatin lavas. They are situated on an island of about one square mile in area, lying in lake De Montigny, Dubuisson township, 40 miles south of Amos, on the Transcontinental branch of the Canadian National railways, and 52 miles east, and slightly south, of Noranda. Geographically, the deposits are favour-ably situated with respect to transportation facilities, a through water-route being available from Amos, along the Harricana river and its lake expansions. The deposits consist of auriferous quartz-tourmaline veins of the fissure-filled type and are of particular interest because of their geological structure and genesis. Furthermore, deposits of a similar type occur both in the Keewatin and in granodiorite bodies to the east, in Dubuisson, Bourlamaque, Pascalis, and Louvicourt townships, and it is hoped that the following discussion may be of some aid in the exploration work now being carried on throughout this general area.

Jan 1, 1932

By R. Elliott, C. A. Pickles, J. Peacey

As the nickel sulfide ore deposits become decreasingly viable as a source of nickel metal, increasing attention is being paid to the exploitation of the nickeliferous laterite ores. Attempts to produce a high grade ferronickel concentrate from these ores by pyrometallurgical methods face several challenges, in particular the selective recovery of the highly disseminated nickel from the reduced ore. The current work explores strategies for maximizing the size of ferronickel particles formed in order to improve the selective recovery of the ferronickel by magnetic separation. The effect of various coal, elemental sulphur, pyrite and sodium sulphate additions on ferronickel particle formation and size at 1000°C have been investigated. It has been observed that increased coal additions leads to a moderate improvement in the size of the ferronickel particles, while the presence of any sulphur bearing reagent leads to a significant increase in particle size. The retention of sulphur in the reduced material has also been studied, showing sodium sulphate has the highest retention, followed by pyrite and then elemental sulphur. An inverse trend was observed in the efficiency of sulphur retention on the basis of residual mass of sulphur per unit mass of reagent added.

Jan 1, 2015

By A. H. Onur, S. Ural

"The Afsin-Elbistan coal deposit with its 3.4 billion metric tons of reserve is the biggest coal basin and one of the most important resources for electrical energy production in Turkey. The coal deposit is located north of Elbistan, Kahramanmaras Province, in southeast Turkey (Fig. 1).The Kislakoy sub-basin of the Afsin-Elbistan basin was selected as the first open cast mine to feed four power station blocks of 340 MW each. The mine is equipped with six identical bucket wheel excavators of the type Sch Rs (2300/5) 32. The annual coal demand of the power station is 18.5 million metric tons. The Elbistan basin encompasses an area of 900 km2, and its centre lies about 1150 m above mean sea level. The sedimentation took place mainly in the upper Pliocene period. The thickness of the coal bed varies from 20 m to 60 m, respectively. The basal part of the coal beds consists of clay, marl and sandy clay. These formations are overlain by gyttja, which may also occur in the form of calcareous ooze, enveloping coal beds. The thickness of the gyttja is up to 35 m (Otto-Gold, 1969). The coal of Afsin-Elbistan is soft coal and the quality has been found to vary considerably throughout the deposit. The thicknesses of the sterile intercalations vary from 0.50 m to 2.2 m and average 1 m in thickness. From the quality control point of view, the coal seam is regarded as upper seam where the gyttja formation occurs as sterile intercalations, and lower seam where the clay formation occurs instead of the gyttja (Fig. 2). The CaO content of upper Kislakoy coal is very high, grinding resistance is low and base to acid ratio of ash, that is, the ratio of acid oxides of metals to base, is greater than one (Ural and Onur, 2001). Contrary to upper Kislakoy coal, CaO content of lower Kislakoy coal is very low, grinding resistance is high and base:acid ratio of ash is smaller than one. Modified Impact Strength Index (MISI) tests are used to determine the grindability of the Elbistan coals (Ural, 1999)."

Jan 1, 2003

"Option pricing is used in finance for valuing options to buy (or sell) shares at some future date because it provides a convenient framework for quantifying values subject to uncertainty. As one of the main sources of uncertainty in mining is the price (sales) of the metal, this approach can also be used for valuing mining projects.The first part of this paper reviews options and option pricing; the second part presents the approach developed by Brennan and Schwartz (1985) for using option pricing to value natural resources. Several applications of this methodology have been published; these are described. From a mining point of view, the assumptions made by Brennan and Schwartz are too simplistic. The weaknesses are discussed with a view to improving an apparently promising new way of assessing the value of projects. IntroductionThe collapse of the British merchant banking group, Barings, has highlighted the risks that can be incurred by speculators and arbitragers in the futures and options markets. But this negative attention on futures and options should not make us forget their positive aspects. They can provide producers and consumers of metals with more predictable sales prices. The introduction of the new traded average price options, TAPOS, by the London Metal Exchange in January 1997 is a response to this need. Equally important, the theory that the finance industry has developed for valuing options provides an interesting framework for valuing mineral projects as well. While this paper was being revised, the South African gold mining house, JCI, announced that it was using a methodology based on option pricing for valuing the mineral rights to deeplevel gold resources (see Box 1)."

Jan 1, 1997