Search Documents

By W. K. A. Congreve

Introduction Less than a hundred years ago the engineer was able to do his job without concern for the science that underlay his practices or for the men who operated his machines. But toward the end of the last century science began to be applied to industry, and its success was such that the plant which clung to empiricism was unable to compete with the plant that followed science. Even more recently, the engineer has been forced to consider the men who operate his machines, for modern large-scale industry has given these men education, social security, and power. Hence the engineer can get good, steady labour to operate his machines only if he can offer inducements. Wages are in general outside the control of the engineer, but he is able to control working conditions. This essay is concerned with one factor of good working conditions: safety. The writer became interested in this problem during three months' summer employment as a student at the Sullivan concentrator of the Consolidated Mining and Smelting Company and was surprised at the distance his investigations led him from the field of pure engineering into the fields of psychology, education, and publicity. Nevertheless, because safety has to do with machines and with men who operate machines, and because it profoundly affects plant efficiency, it is the job of an engineer, not of a psychologist or teacher, nor of the salesman publicity expert who is often so unfortunately employed in personnel relations. The size and complexity of the subject has limited the scope of this essay to the consideration of only a few aspects of industrial safety. Considerable attention has been given to the underlying principles, but the mechanical side of accident prevention, the design of equipment, erection of guards, etc., and the very important problems of organization and administration, have not been given attention proportionate to their importance.

Jan 1, 1948

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By M. Kunst

The creep behavior of three AJ62 alloys was investigated in a wide range of stresses and temperatures. Multi-level tensile creep tests revealed a distinct primary creep stage and a high stress exponent up to a value of 10. The threshold stress concept which is commonly used in combination with high stress exponents was utilized in the analysis of creep behaviour. This resulted in an effective stress exponent for the AJ alloys indi¬cating dislocation climb as the dominating creep mechanism. In addition, microstructural observations of the lamellar eutectic and of the a-Mg-matrix were carried out using opti¬cal microscopy, SEM and TEM. The creep properties of the alloys are discussed in the context of microstructural parameters such as phase volume-fraction, stability and solute supersaturation.

Jan 1, 2006

By Dale C. H. Nevison

One of the most intensive of material rivalries is the confrontation between zinc die castings and plastic injection moldings. Pressed hard by the plastics industry, zinc die casters are learning how to make parts with less material yet without sacrificing quality. The key to this new trend is the technique of Thin Wall die casting. The obvious benefits of Thin Wall are lighter weight and lower cost. Again, obviously, these are the very selling points that put plastics into many appliance and automotive parts formerly made of zinc. One of the factors that has been most conducive to the outstanding growth of plastics has been the increasingly prevalent concept that "adequate" properties are sufficient, especially if there are cost advantages. Most of modern design today is oriented around the reasonable life of a product, rather than indefinitely extended life. This is simply an acknowledgment of the existence of a design environment that pervades many areas, reflecting the life-cyclic desire for change. Too often, so-called "weight-saving" materials end up being very costly - not only in production, but in durability and dependability. Change for the sake of change usually doesn't effect a change for the better. In the majority of cases, the best bet is to design in traditional materials and minimize the material needed, while maximizing the efficiency of the production process. Component prices of products to be produced from either plastics or zinc must be studied in detail to determine which material will produce the lowest cost of manufacture. It is not uncommon for two parts, similar in appearance at a casual look, to have a considerable difference in energy requirements and production costs. Detailed cost estimates of the advantages of each material should therefore be prepared for zinc and plastic parts before the final design and material selection decisions are made.

Jan 1, 1978

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007

By G. Reuben Yourt

IN 1935, Wright-Hargreaves Mines, Limited, initiated an enlarged programme of ventilation. In the mine, surveys were made from time to time by the geological staff, and improvements in ventilation were effected to accord with progress in mining as greater depth was attained. In the summer of 1938 an engineer was trained in the technique of dust sampling. Instruments and equipment for this purpose, such as konimeter, microscope, furnace, etc., were purchased, and a suitable office, equipped with laboratory facilities, was provided. The full time of the engineer is devoted to ventilation and dust control. On surface, in the mill crushing-plant and in the assay office and sample crushing room, an elaborate arrangement of hoods and exhaust systems has been installed to eliminate the dust. These installations, however, are not described in the present paper, which deals only with an extensive programme of underground ventilation as a method of coping with high dust concentrations, increasing temperatures and high humilities.

Jan 1, 1940

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

By P. Lafleur

All indications point to a growing market for thermal coal in Japan as part of the country's current energy policy formulation process. The Ministry of International Trade and Industry forecasts imports of 16 million tons a year in 1985 and 40 million tons in 1990-a twenty-fold and forty-fold increase over the present level. This potential reflects Japan's over-all serious and increasing concern for security of energy supplies and its resultant need to seek alternative sources. Nuclear power will be the main alternative source, but, because it is expected that its development will be slow, imported thermal coal will assume greater importance. Canada, with large resources of all types of coal, could fill a portion of this market. Thermal coal could come from specific thermal coal developments or from metallurgical coal mines, which usually produce a certain amount of coal not amenable to coking, but suitable for power purposes. However, penetration of this Japanese market by Canadian thermal coal will depend on the resolution of a number of problems. On the demand side, siting, environmental aspects, the need for a coal unloading and trans-shipment centre, and the added cost of installing coal-fired stations could be major constraints. Although Canada has ample high-quality resources, any new development tied to the Japanese market will require improvement in prices to cover the high costs associated with transportation, the construction of new mines and the provision of new infrastructure.

Jan 1, 1979

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By Etienne S. Bieler

Mr. Chairman, Ladies and Gentlemen, I come to you tonight distinctly as a physicist, not as a geologist or a mining man. My experience in applied geophysics has been short, and I do not doubt that many of you have a much larger acquaintance: with the subject than I have. A little over a year ago, the firm of Alderson, MacKay & Armstrong decided to investigate the possibility of developing a new method of electrical prospecting suitable to our northern Quebec and northern Ontario conditions, and asked me to take up the work. A preliminary survey of existing literature convinced me that the field of induction methods was most promising. I wish to give you some account of the work carried on last summer in the Rouyn district in this connection with the very able assistance of Mr. H. G. I. Watson. Geophysical methods of prospecting can be divided generally into four classes: magnetic, electrical, gravitational, and seismic. Each class depends on the existence of a definite property in which the valuable mineral to be discovered differs materially from the surrounding rocks. In the four classes, the property will be, respectively, magnetic permeability, electrical conductivity, density, and elasticity. By far the largest differences occur in the case of electrical conductivity, where it is not rare to find ratios of the order of several millions, or even billions, between ores, sulphide ores especially, and the surrounding rock. Hence the sensitiveness and delicacy of electrical methods. Of these four classes, only two, the electrical and the magnetic methods, have been put to extensive practical use in the discovery of metallic ores. The other two classes are important mainly in connection with oil detection.

Jan 1, 1928

By C. R. Powell, W. H. Maher

"This paper presents a short history of the development of milling at Buchans, Newfoundland, and a description of the operation.History and DevelopmentTHE original ore discovery was made at Buchans in 1905 by Matty Mitchell, a Micmac Indian who was prospecting for The Anglo Newfoundland Development Company, which company was then preparing to build a paper mill at Grand Falls, some 50 miles east of Buchans. A development program, initiated in 1906, was terminated in 1911 because of metallurgical difficulties. Intermittent testing was carried out by The American Smelting and Refining Company, and in 1925 a satisfactory method of concentration by flotation was found. Following this, intensive geophysical reconnaisasnce, succeeded by diamond drilling, uncovered two additional orebodies similar to the original discovery at Buchans River."

Jan 1, 1966

By P. E. Cavanagh

Introduction A comprehensive study of the economics of processes for smelting iron ores has been made by the Ontario Research Foundation on behalf of the Ontario Research Commission. This survey has included investigations of all processes in commercial use, and proposed processes which are still in the experimental stage. The two main objects of this work were to discover (l) whether any known processes would be particularly suited to present and future Canadian conditions, and (2) whether any new process would be of assistance in solving the present scrap shortage in Canada. The future prospects of the Canadian iron smelting industry have changed radically in the past ten years. For nearly twenty years before 1939 no iron ore was mined in Canada. The ore used was imported, mainly from the United States and Newfoundland. The economics of iron blast-furnace smelting always force the location of blast furnaces near the source of coal for making high-grade metallurgical coke, and near the market for iron and steel, rather than near the iron ore. Blast-furnace installations in Canada are confined to the north shores of the Great Lakes with ready access to United States coal and ore and the major Canadian markets, and to Nova Scotia near the coalfields of that Province. This distribution of primary smelting capacity naturally results in relatively high prices for iron and steel in the West, the North, and in Quebec.

Jan 1, 1948

ABSTRACT It is critical that historical processes and concomitant exposures to specific nickel substances be understood because some diseases linked to inhalation of certain nickel-containing substances have a long latency between first exposure and disease onset, and because nickel substances vary significantly in their toxicological properties. A discussion of the smelting history and related processes at Vale Canada’s (Inco’s) Copper Cliff, Ontario, smelter is integral to the understanding of these processes. The post-1950 processing history, equipment, propensity for aerosol formation, operational procedures, and ventilation controls used by Vale Canada in roasting, smelting, converting, and copper-nickel separation is discussed.

Jan 1, 2013

By K. W. Edwards

The formulation of a theoretical basis for the evaluation of in-situ coal through the use of geophysical logs is outlined. This involved the development of an approach to the interpretation of resistivity in environments having multiple conductive and non-conductive components. Utilizing this approach and other conventional interpretation techniques, a program was developed yielding accurate determinations of the in-situ percentages of coal, water and ash for the evaluation of coal deposits. Basic information obtained from the CWA program can be utilized in numerous aspects of total mine planning . Some examples of the practical application of this method are included.

Jan 1, 1978

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By John Stubbles

Data are presented on the global warming issue to reinforce the decision by the U.S to reject the Kyoto protocol. The evidence that CO2 is a problem rather than a benefit is inconclusive and will be discussed in this paper. Nevertheless, for economic reasons alone, the US steel industry will continue to minimize CO2 emissions (and the release of real pollutants) per ton of steel through energy reduction programs. However, relative to inevitable increases in absolute CO2 emissions from the utility industry and the transportation sector, future reductions by the steel industry will be inconsequential in the "big picture."

Jan 1, 2004

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By S. H. Ash

No single factor in modern civilization has played a more important part in the lives of our people than mechanization in industry and to it civilization owes much of its progress. In no industry has mechanization met more opposition than in coal mining, where ?the introduction of mechanical equipment has been opposed on many fronts for economic and social reasons. The term 'mechanization? as used in this report refers to the application of machinery to cutting, loading, and transporting coal from the face to the mine cars. During 1933, 84.7 per cent of the underground production of the bitu-minous-coal mines of the United States (1) was cut by machines, while in Washington only 17.6 per cent was machine-cut. Information in this report has been obtained from personal observations and from operating officials in the Roslyn-Cle Elum coal fields, especially D. R. Swem, manager of coal operations, and Thomas Murphy, superintendent, of the Northwestern Improvement Company, to whom the author is indebted for assistance. INTRODUCTION Although Washington coal-mining problems relating co mining methods, ventilation, drainage, and preparation of coal have been discussed in many publications, little has been published on mechanization in this region, principally because it has not been accepted generally that mining machines, mechanical loaders, and conveyors are necessary or economically adaptable to the variable and steeply inclined coal beds of Washington. Production of coal in Washington reached its maximum in 1918, when 4,128,424 short tons were produced; from that year, the trend was downward until 1934, when production was 1,383,103 short tons, the lowest since 1898; for the past two years, production has risen steadily.

Jan 1, 1937