Search Documents

By G. W. Govier

Measurements of the settling rates and the rheological behaviour of heavy media formed of fine suspensions in water of each of magnetite, ferrosilicon, and galena have been made. For media ranging from 1.6 to 2.8 specific gravity the settling measurements gave initial settling rates of from 0.5 to 0.01 ?cm. 'Per minute for magnetite; from 4.0 to 0.8 cm. per minute for galena; and from 35 to 1.6 cm. 'Per minute for ferrosilicon. These measurements indicate the ?relative stability of the suspensions and should be helpful in establishing the useful specific gravity range for each medium. Measurements of the consistency of the media were made with a Fann Model 35 rotational viscometer. Aibnormal or non-Newtonian behaviour was observed in the case of each media, the apparent viscosity being dependent upon the rate of shear or the intensity of motion. Measurements were made over the rate of shear range of 10? to 1,000 reciprocal seconds. The apparent viscosities of the magnetite media ranged from 450 down to 4?0 centipoise at 2.30 specific gravity, and from 2,450 down to 700 centipoise at 2.80 specific gravity. In the case of the galena media, the variation was from 40, through a minimum of 6, to 10 centipoise at 2.20 specific gravity, and from 950, through a minimum of 180, to 450 centipoise at 3.6 specific gravity. The ferrosilicon suspensions exhibited apparent viscosities ranging from 42, through a minimum of 5.6, to 9 centipoise at 1.9 specific gravity, and from 160, though a minimum of 35, to 85 centipoise at 2.8 specific gravity. The dependency of apparent viscosity or consistency upon intensity of motion is considered to be of particular significance in applications of heavy media where the medium is in rapid motion.

Jan 1, 1957

ABSTRACT Inco’s Iron Ore Recovery Plant was operated by Inco from 1955 to 1980 near Sudbury, Ontario. As exposures to specific nickel substances have been associated with adverse respiratory endpoints it is important to understand processes giving rise to such substances. This manuscript discusses the process and equipment, the propensity for aerosol formation, and operational procedures used by Inco in roasting a pyrrhotite concentrate, reducing the nickel in the formed oxide, leaching the nickel in ammoniacal solution, purifying the resulting solution, making green or black NiO, and producing iron oxide pellets. Industrial hygiene measurements are also reported.

Jan 1, 2013

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda's lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

By Maureen Jensen

For mining companies looking to establish a strong North American presence, raise their profile or finance and position themselves for future growth, there is no other destination in the world that can offer a mining company the same opportunities as Canada whether you are an established blue chip or promising junior. Despite historically poor world commodity markets and shaky investor sentiment towards junior explorers caused in part by fallout from the high profile Bre-X fraud, Canada continues to shine as the undisputed mining finance capital of the world. Our natural riches and mining history go a long way to explain Canada's international prominence in mining finance. Canada has actively created and maintained one of the most integrated national frameworks to support mining ventures of all kinds. Our diverse industry, from one-person grass-roots explorers to mining industry giants, is one of our main strengths whether your company is Canada-focused or internationally active. The mining industry continues to be a vital contributor to the Canadian economy, contributing $26.2 billion in 1997 or 3.8% of national GDP, and is the second largest earner of foreign exchange. Industrial mineral companies are a very important part of this strength. These companies require a continuing access to capital to ensure that they can continue to compete and the globalisation of the Canadian mining industry has affected this industry just as much as it has affected every other industry in Canada.

Jan 1, 2001

Reaction between xanthate ions in solution and oxidized compounds present on the surface of galena to form lead xanthate is considered to be a side reaction not contributing to flotation, although accounting for some consumption of reagent. The direct reaction of lead sulphide with xanthate and oxygen to form lead xanthate is the most significant to flotation. Coadsorntion of dixanthogen is also involved. Previous work has shown lead recovery in lead rougher flotation to be a function of m [H+] where: m = concentration of xanthate in solution rHl = hydrogen ion concentration. A plausible explanation for this relationship is suggest-ed. Likewise, the experimental findings that the amount of xanthate adsorbed under certain conditions is a function of m'[H+] are explained in terms of reaction between xanthate ions and soluble basic lead salts such as PbO.PbS04? It is also shown that m[H+] should have a constant value in lead cleaners operating at a higher pH than the roughers. This conclusion is confirmed by plant data, and the value of the constant agrees well with the calculated value. The finding is useful in mill control.

Jan 1, 1965

By J. J. Denny

IN November, 1932, an investigation of silicosis was undertaken at the Mcintyre Porcupine mine, Schumacher, Ont., after a discussion of the p"roblem with Sir Frederick Banting and his staff. As a result, it was decided to carry on dusting experiments with animals at the mine in a manner that would duplicate as far as possible actual industrial conditions. At that time 50 guinea pigs were placed in the crusher house tunnel of the mill where a considerable quantity of fine dust, containing approximately 35 per cent of free silica, was being constantly produced. These animals lived in this atmosphere for periods up to one year, and, while on autopsy large amounts of dust were found in the lungs, not a single case of silicosis had developed. These negative results suggested, among other things, that the mine gases might be a predisposing factor in the production of silicosis, and the results of this investigation (1) led us to undertake the study of the hydrogen-ion concentration of the condensate of the atmosphere, both in the mine and in various sections of the mill. The CO, combining power of blood serum on a series of 400 miners was also studied at this time. While these results were inconclusive, the variation in the hydrogen-ion concentration of the condensate between the surface and underground atmospheres encouraged us to investigate the effect of neutral, weak acid, and alkaline solutions on the solubility of siliceous materials. Gye and Purdy (2) were the first to point out that the chemical reaction, and not the physical presence of siliceous material, was responsible for the production of the fibrosis in silicosis. This work was investigated by Gardner and Cummings (3), who showed that the tissue reaction to quartz was definitely proportional to the size of the particle. They found that 1-3 micron particles of quartz produced an acute proliferative fibrotic response, while the 10-12 micron particles produced only a foreign-body reaction up to a period of three years. It is accepted that the dangerous silica particles retained by the lung are under 5 microns in diameter.

Jan 1, 1937

By Charles T. Harper

The uranium deposits discovered by Amok (Canada) Ltd. in the Cluff Lake area of north western Saskatchewan occur at or near the southern edge of the uplifted basement core of the Carswell circular structure. Two types of mineralization, distinguishable, by their geological and structural setting and mineral paragenesis, have been recognized. The N-Claude type is characterized by a relatively simple mineral assemblage, consisting of uraninite or pitchblende with coffinite, and is accompanied by variable amounts of graphite and organic matter, and Fe, Cu, Pb and Mo sulphides. Both N and Claude orebodies occur within quartzofeldspathic gneisses of the basement core. On the other hand, the D-type ore has a complex mineral assemblage consisting of: uraninite, pitchblende, thucholite and coffinite, along with native gold and selenium; gold tellurides, and selenides of Pb, Bi, Ni and Co; sulphides of Fe, Cu and Pb; and organic matter. The D orebody occurs within carbonaceous shales at the base of the Athabasca Formation as well as in fault zones in regolithic quartzo feldspathic gneisses above the inverted unconformity. An age of 1050 m.y., which is consistent with a period (circa 1200-1000 m.y.) of widespread hydrothermal activity and uranium mineralization or reworking within and adjacent to the Athabasca Basin, has been obtained from uranium mineralization from the D orebody. Later reworking (circa470 m.y.) of the mineralization occurred at the intersection of older mineralized shear zones with radial faults produced during meteorite impact.

Jan 1, 1978

By R. Khanna, K. Hyun Ko, A. J. Berkovich, J. Hook

"The co-pyrolysis of synthetic polymer polyethylene terephthalate (PET) and agricultural wastes (naturally occurring polymer-macadamia nut shell) was investigated in the temperature range 473K to 1273K using a horizontal furnace with an aim to understand their thermal degradation under isothermal conditions. In-depth characterization of pyrolysis residues was carried out using x-ray diffraction (XRD) and solid state nuclear magnetic resonance (NMR) for carbon structure, and through determination of the concentration of unpaired electrons using electron paramagnetic resonance (EPR). In previous studies, it has been found that PET thermally decomposes ~ 650K-700K, releasing (~80 wt % of initial weight) gaseous products due to random chain scission. In the case of macadamia nut shell, three types of byproduct can be obtained from pyrolysis: char, tar and gaseous products. In the co-pyrolysis of macadamia nut shell with PET in 50-50 wt% ratio, total product weight ratio could be modified with the addition of PET acting as a hydrogen source. This is because a recombination of thermal cracking products of cellulose could be suppressed by hydrogen from PET, which will later lead to an enhancement of tar formation. In addition, pyrolysis around 673K is sufficient for bond cleavage to occur in cellulose and lignin leading to the formation of negatively charged activated carbon with high surface area, providing bonding sites for volatiles evolving from PET. Therefore the co-pyrolysis may be able to enhance the product yield (tar/char/solid carbon residue) along with a reduction in the release of gaseous products. During the co-pyrolysis, temperature was found to have a significant influence on the kinetics of thermal degradation and solid residual by-products after co-pyrolysis.INTRODUCTIONPlastics are being used worldwide in a wide range of applications in the modern society; their usage has resulted in increasingly a massive waste problem. The production of most synthetic plastics requires hydrocarbons that are produced from petrochemicals derived from fossil oil and natural gas, a non-renewable source (Speight 2011). Currently, plastic manufacture utilizes ~4% of world oil and gas production, and it is expected to drive further increases in petroleum demand by 1-2% due to their large volume of manufacture (Hopewell, Dvorak et al. 2009). Landfilling and incineration of plastic waste are the two main routes to plastic waste management (Encinar and González 2008). In Australia, only 10% of waste plastics were recycled in 2006 (White and Hyde 2011). This means that large amount of fossil fuels from plastics has either been simply burned for energy recovery or buried in the ground. There is an urgent need for developing alternative avenues for recycling waste plastics. Our group at UNSW has carried out extensive research on the recycling of waste polymers as carbon resource in steelmaking including slag foaming and carbon dissolution from waste plastics into liquid steel at 1600°C; the effect of basic plastic characteristics such as chemical composition, structure, bonding network etc. was examined (Sahajwalla, Rahman et al. 2009)"

Jan 1, 2012

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

By A. G. Mattes

This paper presents an overview of passive, engineered, biologically-based anaerobic bioreactor (ABR) treatment systems of the sort that can be used to remove dissolved copper from mine wastewaters. The paper begins with a brief history of the origins of this treatment technology and continues with a discussion of principles of engineered wetlands (EWs, advanced kinds of constructed wetlands, CWs) and the use of vertical sub-surface flow (VSSF) varieties that contain pulp & paper biosolids as the reactive medium for EW cells. A brief outline of a procedural methodology used in evaluating the potential for biological treatment on a site-specific basis is also included. An introduction to the microbiology of passive biologically-based treatment systems is followed by some recent research results in the general area of wetlands and ABR research. The paper concludes with a brief discussion of several sites known by the authors to have successfully (or not) demonstrated the potential of this treatment option.

Jan 1, 2007

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By J. R. Kadambi, J. Furlan, Kucukal E.

"Hydrocyclones are used in various industrial applications, including mineral processing and tailings management, to separate or classify solid particles and/or liquid droplets from multiphase feed. The fluid flow in a hydrocyclone (used in mineral processing) was investigated numerically and experimentally using particle-image velocimetry (PIV) and refractive index matching techniques. Two turbulence models were used in the calculations: the k–? model and the Reynolds stress model. Particle image velocimetry measurements were taken at various spatial locations along the cyclone. Computational results were validated globally using pressure and flow-rate readings at the boundaries, and locally by comparing the PIV velocity-vector maps and profiles.RÉSUMÉ On utilise les hydrocyclones dans diverses applications industrielles, dont la minéralurgie et la gestion des résidus, pour séparer les particules solides et/ou les gouttelettes liquides de l’alimentation polyphasée, ou pour les classifier. Une étude numérique et expérimentale sur l’écoulement des fluides dans un hydrocyclone (dont on se sert en minéralurgie) a été menée à l’aide des techniques de vélocimétrie par images de particules (PIV, de l’anglais particle image velocimetry) et d’appariement des indices de réfraction. Deux modèles de turbulence ont été utilisés dans ces calculs, à savoir le modèle de turbulence k–? et le modèle aux tensions de Reynolds (RSM, de l’anglais Reynolds stress model). La valeur de la PIV a été mesurée à diverses positions spatiales le long du cyclone. Les résultats de ces calculs ont été validés globalement à l’aide de relevés des pressions et du coefficient d’écoulement d’une extrémité à l’autre de l’hydrocyclone, et localement à des coordonnées spatiales spécifiques en comparant les cartes et les profils du vecteur vitesse PIV.INTRODUCTIONA hydrocyclone is a piece of equipment used to separate and/or classify solid particles or liquid droplets from liquid solid or liquid-liquid feed. Versatile in application, hydrocyclones have been widely used in industrial applications including the food, oil, power generation, chemical, and mineral processing industries. The first hydrocyclone was introduced in 1891 by Bretney to purify various liquids (Bretney, 1891). Hydrocyclones have a relatively simple design with no moving parts, which leads to an efficient separation process."

Jan 1, 2017

By Ralph W. Edie

"IntroductionTHE GOLDFIELDS AREA in northern Saskatchewan has be-come important in recent years because of numerous discoveries of pitchblende. The area is underlain by rocks of Precambrian age and, because of metamorphism and hydrothermal alteration, the geology in the vicinity of the pitchblende deposits is exceedingly complex and presents a challenge to all geologists •working in the district. This paper is a contribution to the geological literature of the area and presents a description of rock types, supplemented with petrographic, chemical, and spectrochemical data.Field work in connection with this paper was carried out during the summers of 1948, 1949, and 1950 while the writer was employed as assistant geologist for the Crown Corporation, Eldorado Mining and Refining ( 1944), Limited, Gold-fields area. Laboratory work was undertaken at the Massachusetts Institute of Technology during the winter months of 1949-50 and 1950-51 and extended through the summer of 1951.With the exception of SiO2and FeO, all of the new analyses ( 1) presented were carried out by quantitative spectrographic techniques under the supervision of Dr. L. H. Ahrens at M.I.T. Many of the techniques have only recently been developed at that Institute and detailed laboratory procedures have not yet been published."

Jan 1, 1952

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By M. H. Fathi

The aim of this work was to prepare the metallic coatings on 316L stainless steel dental implant and evaluate the corrosion characteristics and thus the biocompatibility of the uncoated and metallic coated dental implants and comparison of the effect of the type of coatings on biocompatibility. Three types of metallic coatings including Tantalum, Niobium, and Titanium coatings were made using physical vapor deposition process on 316L stainless steel dental implant. Structural characterization techniques including; X-ray Diffraction, Scanning Electron Microscopy and Energy Dispersive X-ray Analysis were utilized to investigate the microstructure and morphology of the coatings. Electrochemical potentiodynamic tests were performed in two types of physiological solutions at 37±1 °C in order to determine and compare the corrosion characteristics. All three types of metallic coatings had a positive effect on improvement of the corrosion behavior so that the coatings could increase the corrosion resistance of 316L stainless steel and this trend was independent to the type of physiological environment. Biocompatible metallic coatings could decrease the corrosion current density that is a distinct advantage for prevention of ion release. This can improve the biocompatibility of the implant and, consequently prevention of tissue damages, inflammation and irritation and obtained desirable histopathological response.

Jan 1, 2007

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002

By M. B. McClenaghan, O. P. Lavin, Ian Nichol

"Abstract-Exploration in most areas of Canada has to contend with problems posed by glacial overburden. In many areas exploration for gold has been based on the sampling of tills, frequently by deep overburden drilling, and analyses of heavy mineral concentrates. Notwithstanding the significant role that till geochemistry has played in the discovery of some important gold deposits over the last few years, increased appreciation of the nature of the glacial history and stratigraphy and the character of gold within till has led to the recognition of a number of ways whereby the effectiveness of exploration can be improved upon.In order for till geochemistry to be useful in exploration, a number of conditions must be fulfilled, including:1. mineralization, or alteration halo related to mineralization, subcropping at the bedrock /over­ burden interface; 2.glacial erosion and dispersal of a recognizable signature of mineralization into the glacialsediments; 3, preservation of glacial sediments containing this geochemical component (trace metal or mineral) at positions subsequently selected for sampling (normally drill sites); 4. correct identification of specific till units and associated ice movement history; 5. collection of adequately large and representative samples; 6. appropriate sample preparation and processing; 7, appropriate geochemical analyses; and 8. correct data processing and interpretation.While we have no control over the first two geological conditions, and only limited controlover till availability, we can control the quality and thoroughness of sampling, sample identification, sample preparation, analysis and interpretation. In particular attention needs to be focussed on obtaining a large enough sample to be adequately representative, an unbiased sample must be collected, together with appropriate sample processing, analysis, data processing and interpretation. It is considered that by modifying or extending existing approaches to gold exploration the chances of exploration success can be increased. In particular, analyses of both the heavy mineral and minus 63 ?m fractions of till is recommended because gold in till may occur in different size fractions."

Jan 1, 1992

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012