Search Documents

By W. A. Lang

RESEARCH has been defined as the link between the present and the future. Science, wonderful though its achievements may be, has but scratched the surface of the unknown. Research is directing its attention to winning new facts in order that their application to the processes of today may open up new sources of wealth for the common benefit. Two classes of research investigations are often recognized-fundamental and applied, but these classes merge into each other and it is often hard to distinguish one from the other. Fundamental research is carried out primarily to develop basic facts, but frequently these are found to have immediate economic value, while applied research, specifically aimed at economic values, often necessitates a preliminary fundamental investigation. Both are essential and both should proceed by scientific method. It is obvious in fuel technology that a knowledge of the physical and chemical constitution of the various coals is fundamental to their industrial utilization, and further, a knowledge of the way these coals react under different conditions of temperature, atmosphere, etc., is necessary in solving such problems as storage, combustion, carbonization, gasification, or con-version to liquid fuels. The wide range of coals, the complexity, of their constitution, and the many uses for coal, makes fuel research no simple subject but one with unending possibilities. The Research Council of Alberta, formerly known as the Scientific and Industrial Research Council of Alberta, was established in 1919, to promote the development and conservation of the natural resources of the Province. The work of the Council was arranged in six major divisions: Fuels; Geology; Road Materials; Soils; Natural Gas; and Forest Products. The office and laboratories are located in the University of Alberta. The Council was financed until the depression of 1933 by a separate vote of the Legislature, but since then has been continued, though on a much smaller scale, as one of the activities of the University. It might, however, be noted that although the Council is now in abeyance, a skeleton organization has been maintained so that it can be brought back to active service as soon as conditions warrant. Annual reports are still submitted to the Legislature. Funds have not been made available, however, for the publication of the last five reports.

Jan 1, 1942

By Glenn D. Lyle

As part of an initiative to improve value in mining, CEMI is developing a handbook on best practice in mine design. Various formats were examined, and of these, the wiki was selected as being most suitable. Being web-based, its global reach and capability of being continuously updated allows the wiki to evolve as new knowledge is generated, and to capture the diversity of experience of practitioners in the mining industry. While wikis have many advantages in terms of organizing content and searching, their ability to be edited by users is often seen as a negative characteristic for quality control. To ensure reliability of information content, author attribution, specific authorship models, and a peer review process have been implemented, in addition to the standard version tracking capability of wikis. The first phase of the project concentrates on topics related to underground hard rock mine design. The scope will be expanded to cover other aspects of mining as the project matures. Strategic partnerships with various organizations, such as the CIM, and CANMET, are being formed to provide a wide range of seed material to stimulate growth of the site. www.minedesignwiki.org

May 1, 2011

By P. Desclaux, A. Gosselin

"In 1999, PFC measurements were carried out at Alcan smelters as part of a large measurement campaign led by the Canadian Aluminium Association. Side worked prebake (SWPB) and horizontal stud Söderberg (HSS) plants in Arvida were the selected sites. CF4 and C2F6 emissions were measured continuously in the exhaust duct and at the roof vents for a week. In parallel, voltages from four designated cells were recorded at a high scan rate. Results were analyzed and correlations between voltage, anode effect duration and PFC emissions were tested. Some fundamental anode effect mechanisms were proposed and validated with the observations. IntroductionFollowing the international agreement reached within the scope of the Kyoto protocol, voluntary partnerships have been established in many countries especially for the aluminum industry. It is well known that the PFCs that are periodically emitted during aluminum production are the major source of fluorocarbon emissions. The latter are part of the greenhouse gases. In the fall of 1999, Alcan announced that it will adopt, promote and regularly renew a long-term greenhouse gas management commitment at all of its facilities within the framework of the so-called TARGET program that was implemented during 2001. The program is intended to produce on-going reductions, which will be reported publicly on an annual basis.Improvements in the understanding of the mechanisms leading to PFC emissions will contribute to targeting the most appropriate reduction actions. PFC measurement campaigns have been driven toward this end. The first measurement campaign was conducted in 1993 in order to get a picture of the emissions and a base line. The last measurement campaign was conducted in 1999 and its main objective was to compare current emissions with those measured in 1993 and to confirm the accuracy of the predictive equations for the calculation of PFC emissions. This campaign has been conducted by the Canadian Aluminium Association and measurements were made in plants using different technologies. Results of this campaign have already been reported by Bouchard et al. (2001)."

Jan 1, 2002

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

By A. P. Schissler

Mining has several characteristics, uncommon in other business sectors, which pose additional challenges to the implementation or design of IT and management systems that use the information. Understanding these characteristics would improve the chances of successfully importing new information technology and management techniques to mineral producers. The most important characteristics that should be understood are workplace issues, the industry’s dual nature of being a continuous construction project using cyclical factory processes, labour challenges, workplace culture, information availability, integrative data elements, and the current technical education of mining engineers. These characteristics were taken into account in two applications of information technology and systems design at operating companies. The research and consulting projects focused on the development of an IT-enabled performance management system at several underground metal mines in Canada and an integrated data warehouse for surface mines spread throughout the United States and Latin America.

Jan 1, 2006

By G. E. Wittur

"The twenty-one members of the Organization for Economic Cooperation and Development, comprising eighteen western European nations plus Canada, the United States and Japan. account for two-thirds of world steel production. The Special Committee for Iron and Steel was formed by the OECD to study trends and problems in the steel industries of member countries. The paper begins with a summary on the Organization, including an historical sketch, its structure, member-ship and objectives. The steel industry of the entire OECD is briefly described before proceeding to a more detailed discussion of various aspects of the steel industries of European OECD members, emphasizing practices and conditions that differ from those in North America. Benefits to Canada of representation at meetings of the OECD Special Committee for Iron and Steel are described."

Jan 1, 1967

By N. S. Spence

INTRODUCTION WHILE TITANIUM, the element, has been known for over 150 years, titanium, the metal, is a relative newcomer to the metallurgical and industrial scene. The reasons for this chiefly lie in the refract1Hy nature of titanium compounds; the high melting point of the metal; the great activity of elemental titanium, particularly at temperatures close to .and above the melting point; and the pronounced deleterious influence of certain impurities on its mechanical proper-ties. Early efforts at production of the metal were, consequently, either unsuccessful or resulted in products having sub-metallic properties. With the considerable improvement in equipment, materials, and skills that have developed within the past twenty-five years, later investigators have had a better opportunity to overcome some of the inherent practical obstacles and to come to grips with the essential technical problems. NATURAL ABUNDANCE OF TITANIUM Titanium is one of the most abundant metallic elements. It has been estimated (1) that titanium comp-rises about 0.65 per cent of the earth's crust, and therefore ranks fourth among the structurally useful metals in the order: aluminum, iron, magnesium, titanium. It must be appreciated that the relative abundance of the element is only a crude indication of its potential availability, since a very substantial proportion is present as a minor constituent in practically all igneous rocks. By comparison, present-day ores of titanium are relatively few and are but a minor fraction of the estimated total titanium contained in the earth' s crust.

Jan 1, 1951

By J. Forster, C. A. Pickles, Mackowiak. K.

The future development of nickel laterite deposits is crucial with regards to satisfying impending nickel demands. The commercial implementation of new hydro/pyrometallurgical processes in recent years has led to significant improvements in the extraction of nickel from the laterite ores. One potential alternative pyrometallurgical processing route would be to selectively reduce the nickel and produce a concentrate with nickel contents similar to those attainable in the conventional flotation of sulphide ores. However, even bench scale studies have not yet been able to produce a high grade (>15% nickel) concentrate from a low grade laterite ore. The present research involved the microwave vacuum reduction roasting of a nickel laterite ore to yield a high grade concentrate, rich in nickel. Firstly, the effects of temperature and pressure on the nickel grade and recovery were investigated using a thermodynamic model. Secondly, briquettes containing a mixture of charcoal and a low grade silicate nickel laterite ore were reacted in a microwave vacuum system. The experimental variables studied were the input microwave energy, pressure and absorbed microwave power. Thirdly, the ferronickel in the reacted briquette was concentrated by magnetic separation and nickel grades of up to 21% could be achieved.

Jan 1, 2015

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By A. H. Winckers

"CAMIRO, The Canadian Mining Industry Research Organization, formerly known as MITEC, is a collaborative research organization of Canadian Mining Companies. It is comprised of Exploration, Metallurgical Processing and Mining Divisions.The Metallurgical Processing Division (MPD) has the mandate to contribute to the profitability, competitiveness, safety and growth of the Canadian mining industry by improving the efficiency and effectiveness of mineral processing and extractive metallurgy in an environmentally conscious manner through the development of innovative technology by managing cooperative industry focused research programs.Current membership includes about ten Canadian mining companies. Past research has largely focused on base metal mineral processing. The Division wants to expand its research base to include all areas of mineral processing and extractive metallurgy.Past performance and plans for the future will be highlighted in the presentation."

Jan 1, 1998

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By Steve W. Ciccone

The Red Dog Mine is both the largest known zinc reserve and the largest zinc producer in the world. The mine started in 1989, and by 1999 had increased production from approximately 300,000 tonnes per year (t/yr) of zinc concentrate to in excess of 900,000 t/yr. The VIP Mill Optimization Project further increased zinc concentrate production to 1.1M t/yr while improving both product quality and zinc recovery. The Mill Optimization project also addressed a number of issues related to risk reduction: power generation capacity, water treatment capacity and concentrate thickening. The project was faced with numerous challenges, the most daunting of which was the schedule. This US$105M project was executed, from conception to completion, inside of two years. Less than nine months elapsed from concept to delivery of materials and equipment to site. The project also faced a 100-day icefree shipping window, the challenges of construction in an Arctic environment, and an extremely tight labour market for qualified craft personnel. These challenges were successfully addressed with several innovative approaches to project execution, including an Alliance contracting arrangement between the owner, engineer and contractor; full integration of the team; construction of modules in Anchorage; and fast-track engineering, procurement and construction. Steve Ciccone, AMEC?s project manager on the Mill Optimization project, works for the Mining & Metals unit of AMEC, a world leader in the provision of engineering and construction services. He obtained his BASc from the University of British Columbia and is currently midway through his MBA program at Simon Fraser University. Steve has 15 years of experience providing engineering and project management services on mining and metals projects, and has been involved in the execution of five capital projects and several studies at Red Dog since 1995. George Hope was responsible for process design and engineering on the Mill Optimization project and has been Manager, Project Development at Teck Cominco since 1995. Prior to this time, he was a project manager and chief metallurgist for Lac Minerals for 14 years and a mill superintendent and metallurgist for Noranda for 5 years. George received his BSc in Mineral Technology from the Royal School of Mines in England.

May 1, 2002

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

Ground support audits are sometimes necessary in ageing underground mines. Usually, the purpose of such audits is to assess the state of the ground support in various parts of the mine, identify areas that require attention and establish rehabilitation requirements. In 2005, Brunswick Mine, located in Bathurst, New Brunswick, Canada, completed a comprehensive mine-wide ground support audit. The areas examined included excavations in several mining blocks, as well as ramps, shaft stations, garages, shops, etc., throughout the mine. A vast amount of data was collected over a period of two weeks by multiple auditing teams. The audit was followed by a data digitisation exercise, and the creation of a data management system to store audit results and keep track of subsequent rehabilitation activities as they occur. One aspect of the data management system was the incorporation of a function for reporting on ground rehabilitation progress, along with the capability of updating mine level plans for easy visual presentation of this progress. This article describes the approach implemented at the mine to carry-out the audit, as well as the database constructed to manage the results.

May 1, 2009

By John Plecash

This paper comprises a general outline of all of the developments, including the history, geology, mining, milling, power and transportation installations, at the gold mining operation of La Luz Mines Limited and the copper mining operation of its wholly-owned subsidiary, Rosita Mines Limited, both located in north-central Nicaragua. The low-grade, gold-bearing ore-bodies of La Luz Mines, contained in highly fractured and folded Lower Cretaceous sedimentary rocks, were from 1909 to 1928, mined and treated by primitive methods by the La Luz and Los Angeles Mining Company. The abandoned property was acquired by La Luz Mines Limited in 1936, and was equipped with modern machinery and put into production in 1939. Between 1939 and 1948, the daily rate of production was in-creased from 300 tons per day to 2,-000 ton per day. The ore reserves available for open-pit mining were depleted in 1954. Since then, the entire production has come from under-ground operations.

Jan 1, 1963

By C. -K. Fang

"Aging effect on the wear resistance of alumina particulate-reinforced 6061 aluminum matrix composites with a block-on-ring wear tester has been investigated. Specimens with various Al2O3 volume fractions of 0%, 10% and 20% were employed in this work. Experimental results indicated that over-aged monolithic 6061 Al had the best wear resistance, as compared with under-aged and peak-aged conditions. For the composite containing 10% Al2O3, over-aging and peak-aging resulted in similar wear resistance, which was higher than that for underaging conditions. For the composite containing a high volume fraction (20%) of Al2O3, the wear resistance reduced with the increase in aging time. Although longer aging time was favourable to the wear resistance of monolithic 6061 Al, it was detrimental to that for the Al2O3/6061 Al composite with high volume fraction of particles. IntroductionMetal-matrix composites (MMCs) have received attention in many engineering applications because of the demands for high specific strength (strength-to-weight ratio) and specific stiffness, good high temperature capabilities and wear resistance. The manufacturing processes of fiber-, whisker-, and particulate-reinforced MMCs have been well developed (Hosking et al., 1982). Because of the reduction in fabrication cost, the applications of MMCs have been widely extended to light weight-bearing sleeves, calipers, automobile parts (brake rotors, drive shafts, connecting rods, piston rings, and cylinder liners), sporting goods, aerospace components, tanks (wheels, speed brakes, and track shoes) and other industrial applications. Among the three types of metal matrix composites, particulate-reinforced MMCs are promising because of their homogeneous and isotropic material properties and low cost. Additionally, they can be formed using conventional metal processing techniques."

Jan 1, 2003

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

By Y. Okita

The Goro Nickel Process, developed over a ten-year period, uses a number of novel processing steps and treats two ore types, limonite and saprolite, together. Nickel and cobalt are solubilized using a 270°C pressure acid leach in sulphuric acid, which rejects the bulk of the Fe into the leach residue as hematite particles. The leach liquor, after CCD, is aerated to oxidize any ferrous iron to the ferric form and is neutralized with limestone to precipitate iron as hydroxides together with gypsum from the neutralization of the free acid. Further neutralization with lime, together with steps to remove suspended solids, reduces the iron to trace concentrations. Nickel and cobalt are directly recovered from the low-iron leach solution by primary solvent extraction using Cyanex 301® (SXl) in a high-strength hydrochloric acid solution. Nickel is subsequently separated from cobalt in a secondary solvent extraction circuit using tri-isooctylamine. A granular nickel oxide is made by pyrohydrolysis, and this allows the recycling of hydrochloric acid to SXl. The process is currently being commercialized to produce approximately 60,000 t/y of nickel as nickel oxide granules and approximately 5,400 t/y of cobalt as cobalt carbonate. This paper describes the process development to control the Fe concentration in the SX1 feed solution.

Jan 1, 2006

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016