Search Documents

By Robert E. McIvor

"“Classification System Efficiency (CSE)” is a powerful, emerging tool that can be used to increase grinding circuit efficiency. It is defined as the percentage of the ball mill energy being used to grind target, oversize particles. The discovery, validation and current use of CSE, including how it was manipulated, are described through seven plant case studies. These resulted in efficiency improvements ranging from 3 to 30 percent, along with major reductions in over-grinding. The achievable CSE for any given circuit is described. This paper demonstrates both how, and how much, every plant can benefit from increasing grinding circuit CSE.DEFINITIONS: BALL MILL CIRCUIT “CLASSIFICATION SYSTEM EFFICIENCY (CSE)”, “EFFECTIVE MILL GRINDING POWER”: “WASTED/OVER-GRINDING MILL POWER”The closed ball mill circuit is shown in Figure 1. The extreme importance of the circulating load ratio in determining circuit productivity was demonstrated by Davis (1925) and re-published by Guadin (1939), as shown in Figure 2. The circuit production rate increases with increased circulating load ratio, rapidly so at first and continuing to increase more gradually with higher and higher values of circulating load ratio.The underlying cause of this relationship was seen when comparing the ball mill feed and product size distributions from two different ball mill circuits, one with a low circulating load ratio, and one with a high circulating load ratio (Figure 3). While the F80’s and P80’s of these two circuits were close to the same, the mill feed and discharge size distributions were quite different. The ball mill in the circuit with the higher circulating load ratio contained a substantially greater fraction of material coarser than the target P80, as indicated by the respective mill feed and discharge size distributions. This fraction represents the fraction of the mill power being expended on “coarse” (in this case, plus P80 size) material, or the circuit “classification system efficiency.” The “effective mill grinding power” is the total mill power multiplied by the CSE. The compliment of CSE, the remaining fraction of “fines” in the mill, is the fraction of the mill power being wasted, and spent on over-grinding of material already finer than the circuit target product size. This is the “wasted/over-grinding mill power”"

Jan 1, 2013

By B. K. Gorain

"Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine.Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects.The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems.INTRODUCTIONThere are various challenges to successful development of mineral resources. Most of the ore bodies being developed worldwide are of lower grades requiring high throughput to be economical. Many of these lower grade ore bodies have significant occurrences of deleterious and penalty elements that could render a deposit unworthy of development unless there are technological solutions to process them economically in a sustainable manner with minimal environment impact. Even in a high metal price scenario, the economics for some of these low grade ore deposits is marginal. From a metallurgical perspective, these ore bodies have complex mineralogy and use of any off-the-shelf technology is not always effective. Development of innovative processes are often required, which is expensive, time consuming and sometimes risky.This paper will provide a broader perspective on the steps involved in solving flotation problems for operating plants and for greenfield development projects. In addition, some of the key challenges in flotation of complex low grade ore bodies along with the economic benefits in developing solutions to these problems will be presented."

Jan 1, 2013

By P. K. Naik, B. Das

Flotation studies were carried out to recover carbon values from blast furnace flue dust containing ~30.34% carbon, 4.6% volatile matter (VM), and 65.03% ash. The variables chosen for the experiments were dispersant (sodium hexametaphosphate), pH, collector (diesel oil), and frother (MIBC). The experiments were designed according to a 24 full factorial design method and regression equations for the recovery of carbon and product grade were determined from the data. Experiments were performed to optimize recovery and grade using the steepest ascent method. The maximum recovery of carbon was 90.0% with a concentration of 56.5%, whereas the maximum obtainable grade of carbon was 66.35% with 50.45% recovery.

Jan 1, 2005

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By M. Helinski

In the authors? experience inappropriate water management in hydraulic fill masses has been the root cause of most barricade failures. Inappropriate water management can lead to high water pressures, reduced effective stresses and increased barricade stresses (Kuganathan 2002). In addition the high hydraulic conductivity and non-plastic nature of most hydraulic fills makes susceptibility to piping failure (Cowling et al. 1987) a high possibility in many hydraulic backfills where a static water head is available. In order to avert both of these failure mechanisms it is essential to control the elevation of the phreatic surface within the fill mass. This is usually achieved through campaigned filling and resting periods. The duration of filling and resting periods are often estimated using some form of stope drainage simulator. Due to the random nature of many characteristics that influence the fill mass hydraulic conductivity, simulation of hydraulic fill drainage can be difficult. The high consequences of inaccurate phreatic surface estimates combined with the high variability in drainage properties often results in operators taking a conservative approach to this modelling. This conservative approach can lead to significant delays in the filling cycle which can have a major impact on the productivity of many hydraulic fill operations and can often results in an unnecessary movement towards capital intensive paste fill systems. This paper presents a water management technique which combines a simplified drainage model with in-situ monitoring to provide a rational approach to water management. With an accurate drainage model filling operations can be carried out at optimum efficiency without compromising safety. The implementation of this strategy has lead to a significant increase in filling rates at a number of Australian filling operations. A brief case study from one of these sites has been presented.

May 1, 2007

By David R. Skuse, Jacek A. Kostuch, Steven M. Fortier

"Particulate ground calcium carbonate (GCC) is used as a filler and coating pigment in a wide range of applications including papers, paints, plastics and films. In this paper we will overview the requirements for GCC used in both filling and coating applications in the paper industry and highlight the processes used in the production of these materials.INTRODUCTIONCalcium carbonate is both abundant and very widely distributed occurring most commonly as limestone, marble and chalk (Harben 2002). Given, the high purity, whiteness and relative inertness of these materials it is not surprising that they are heavily utilised in a range of industrial applications. Worldwide ground calcium carbonate (GCC) capacity is estimated at 50.5 million tonnes per year (Roskill, 2002). This usage is divided between relatively coarse materials that are used in applications such as landscaping, cultured marble and carpet backing and finer grades that find application in plastics, rubbers, inks, paints and paper. Given the usage of calcium carbonate products across a very wide range of consumer products, the outlook for GCC is very promising with growth expected in many markets. Growth is anticipated across many applications in the emerging nations and more specifically in paper applications on a global basis.Over the last several decades the GCC processing industry has evolved to be well adapted to both the cost effective production and delivery of standard products and the production of high performance speciality products. Many of the standard unit operations found in the metaliferous raw material processing industry are also used, albeit in some cases in modified form, in the processing of GCC. Coarse products (diameter > 3 - 10 µm) are typically produced by dry processing routes. Whereas, the finer products are typically produced by a combination of wet and dry processing."

Jan 1, 2004

By Alain Blouin, Mohamad Sabsabi, Aissa Harhira, Paul Bouchard, Greg Lithgow

"The objective of this study was to demonstrate the application of Laser-Induced Breakdown Spectroscopy (LIBS) to the continuous analysis of online monitoring of Al, Mg, Ni, Mn, Si and Fe in nickel ore limonite and saprolite slurry samples. Analysis was performed on slurry samples in air at atmospheric pressure. Two pure samples of limonite and saprolite were used. Mixtures of the two samples in varying proportions were used to build calibration curves, study the influence of solid/liquid ratio, and evaluate short and long term reproducibility. The LIBS measurement of these elements is independent of the water content (from 70-85%, the range allowed by our setup). Repeatability of the measurement and long term reproducibility (from day-to-day) were below 1.2 % and 2% respectively for all the elements studied in our conditions. The results obtained showed that an industrial LIBS analyzer could provide the chemical composition of the six elements Al, Mg, Ni, Mn, Si and Fe within 1-2 minutes.IntroductionThe metal-producing industry faces the major challenge of increasing productivity, reducing costs, and maximizing benefits from existing equipment. By pyrometallurgy, metal making involves the basic steps of charging the furnace, melting the charge and refining. By hydrometallurgy, the metal refining is carried out through the dissolution of the metal by chemical reaction and electrolysis. During refining either by pyrometallurgy or hydrometallurgy, it is critical that operating parameters be adjusted and controlled so that the chemistry of the melt or the solution is within predetermined limits. Presently, the complete turnaround time for sampling, sample transfer, analysis and communication of the results to the operators is often 30 minutes or more."

Jan 1, 2016

By F. Dai

Due to difficulties associated with gripping in direct tension, indirect methods are commonly used to measure rock tensile strength. In this work, we adopt an innovative indirect tensile test method: Semi-Circular Bend (SCB) to measure the tensile/flexural strength of Laurentian granite (LG). The static tests are carried out with a servo-controlled material testing machine and the dynamic tests are conduced with a Split Hopkinson Pressure Bar (SHPB) system. Pulse shaping technique is adopted to achieve dynamic force equilibrium in SHPB to facilitate data regression. Finite element method is used to relate the failure load to the tensile strength. Strong rate dependence of the tensile strength is observed. The flexural strength is higher than the tensile strength measured using Brazilian Disc (BD). This difference is rationalized using the non-local theory. To further validate the method, a coupled Finite element/Discrete element method (Fem/Dem) in conjunction with the smeared crack model is utilized to simulate the fracture process during dynamic SCB tests. The resulting fracture patterns are qualitatively consistent with those from recovered samples. Both the experimental and numerical methods have validated the results and this new method is readily to be used for other rocks and other brittle materials.

May 1, 2009

Background Chronology 2008 Positions May 8, 2010 Summit Going Forward Say one thing and do another ??Genuine passion to see our customers succeed?, ?A passion for exceeding our customer?s expectations? Self serving actions to gain competitive advantage at the expense of the customer No single supplier or technology can manage the overall mine and its integrated operation - April 2005: Informal meeting at Toronto CIM 2004 -Unanimous interest - July 2005: Formal Calgary Meeting, developed: - Scope and vision statement , - OEM/OTM communication plan, - industry communication plan - Aug?Nov 2005: Aligned with SMART - Nov 2005?May 2006: Direct OEM, OTM communication - May ?Sept 2006: Developed baseline standards - Sept -April 2007: Developed SMART document - Sept 2007: Document distribution and request OEM OTM response - Jan ?May 2008: Acquired OEM OTM feedback and positions May 2008: Results presented to SMART and discussions on next steps

May 1, 2010

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By Mike Samuels, John Starkey

"This paper examines test results and grinding mill design for the recent Fortune Minerals’ NICO Project, located in the Northwest Territories. SAG milling and rod milling options are compared. Rod milling is clearly shown to be the best option because of the ore’s extreme resistance to breakage in a SAG mill environment.Surprisingly, the Bond Ball Mill Wi was 13 kWh/t for this ore. The Bond Rod Mill Wi was 20 kWh/t, whereas the SAG pinion energy to grind the ore to T80 1.7 mm was 30 kWh/t. The existence of ore with this ratio of SAG hardness to Bond BM Wi has not been previously observed. If not considered, this critical relationship may adversely impact the accuracy of mill design. This paper substantiates the significance of these findings to achieve successful grinding design on ore that is macro-competent during primary size reduction, but relatively normal during secondary grinding.INTRODUCTIONThe NICO Cobalt-Gold-Bismuth-Copper deposit is located 160 km northwest of the City of Yellowknife, Northwest Territories. It is the largest IOCG-type deposit (aka Olympic Dam-type) currently recognized in Canada with Mineral Reserves of 21.8 million tonnes contained within a larger 57 million tonne, lower-grade Mineral Resource. The project, owned 100% by Fortune Minerals Limited, has been assessed in a positive definitive feasibility study, subject to underground test mining and pilot plant testing, and is now in the permitting stage to develop a combined open pit and underground mine and process plant. An updated process flow sheet incorporates conventional crushing, grinding and bulk flotation, followed by filtration for shipment of a concentrate to a purpose-built refinery proposed to be built near Saskatoon, Saskatchewan. At the refinery, separate bismuth and cobalt concentrates will be produced following regrinding. The hydrometallurgical process methods include: pressure acid leach, precipitation, ion exchange, and electro-winning for recovery of cobalt as 99.8% cathode; solvent extraction and electro-winning of by-product copper cathode; ferric chloride leach and electro-winning for recovery of bismuth as 99.5% cathode; and cyanidation of the leach residues for recovery of gold as doré."

Jan 1, 2010

By Paul Hughes

This paper summarizes current underhand paste backfill mining as applied to Goldcorp Inc?s Red Lake Mine, Newcrest Mining Ltd?s Kencana Mine and the Lanfranchi Nickel Mine as well as ongoing research at the University of British Columbia?s Norman B. Keevil Institute of Mining Engineering. The Red Lake Mine utilises a 6 m wide undercut with a 2 MPa unconfined strength paste in order to selectively mine its high grade, high-stress orebody. Kencana?s orebody is located in a poor rock mass environment. An 8 m wide, 2 MPa unconfined strength paste sill allows a safe working condition for its high grade orebody. The Lanfranchi Nickel Mine utilises a cable-supported, 2 MPa paste, with 12 m span sills, to optimize the mining of the squeezing rock mass. This paper details the rock mechanic hazards, ground support techniques, paste practices and unique conditions for each mine. Further, an update of ongoing research at the University of British Columbia, focussing on the optimization of safe mining in underhand cut-and-fill mining in high-stress/weak rock masses, is presented.

May 1, 2011

By E. S. Yan, R. Graley

"The StackCell was developed to overcome the engineering and design challenges that are commonly associated with existing flotation technology such as pneumatic, self-aspirating cells, mechanical cells, and flotation columns. These challenges include high energy consumption, large floorspace requirements, and size. They are most evident when designing systems to process streams containing a high volumetric flow rate coupled with a significant float yield. Unlike many metalliferous and industrial mineral applications, fine coal flotation circuits are typically characterized by feed streams containing a low solids content (<5%, by weight) where up to 85% of the feed can report to the product launder. With input from major engineering houses and end-users, the Eriez Flotation Division (EFD) developed the StackCell technology with the goal of providing an additional flotation option for end-users. This technology was designed specifically to overcome these challenges by providing an efficient method of separation in terms of metallurgy, but also with respect to equipment size, energy consumption, and installed costs. Besides being placed in tandem with existing cells to provide cost-effective supplemental capacity, this technology can be installed in a stand-alone arrangement as recently demonstrated at Patriot Coal’s Kanawha Eagle preparation plant. This manuscript provides an understanding of the underlying fundamentals of this new technology and presents data from Kanawha Eagle in addition to other industrialscale installations.INTRODUCTIONOver the past decade, column flotation has continued to gain acceptance as an alternative method for recovering fine coal due to superior metallurgical performance as compared to mechanical flotation cells. This point has been proven on numerous occasions by comparison of plant flotation data with the release analysis separation curve (Dell et al., 1972). Data from a release analysis test approximates the ultimate flotation response of a coal sample. In North America, a number of investigations have been published that document bottom-line improvements achieved using column cells (Luttrell et al., 1999; Kohmuench et al., 2004; Baumgarth et al., 2005). According to these reports, the benefits are derived from an overall increase in plant yield that can be achieved due to the improved product grade in the flotation circuit. In particular, the application of wash water to a deep froth utilized in column flotation minimizes the nonselective recovery of high-ash ultrafines that are hydraulically entrained in the froth by conventional flotation machines."

Jan 1, 2013

By C. J. Farrow, M. J. Smith

"Bechtel has managed a number of test programs to establish autogenous grinding circuits and size mills for a variety of ores.This paper outlines the procedures whereby bench scale and pilot plant tests are used to select the most efficient circuit to grind the range of ore types likely in the mill feed.Five examples are given. One example traces the development of a pilot plant program; it shows how bench scale Work Indices provide a target for the grinding power requirement of an ore and relates how pilot circuits are changed as a result of interpreting the results from preceding tests. The other four examples relate the interpretation of the test results to provide design data; they illustrate a number of phenomena which have been observed.INTRODUCTIONConventional crushing and grinding circuits can be specified from bench scale test data such as Bond Work Indices. Bond Indices have been correlated to a large number of rod and ball mills and by applying appropriate factors, mills can be sized from the Work Index.For autogenous or semi-autogenous grinding circuits, bench scale tests are not sufficient to be able to specify the circuit and size of the mills for a commercial plant. It is necessary to run a series of pilot plant tests to determine how the ore behaves."

Jan 1, 1982

By Elizabeth Gardiner

Tailings and water management facilities are integral components of mine and mill operations. They must be managed for the long term to ensure that safe and environmentally responsible stewardship is achieved. The Mining Association of Canada (MAC) has developed and published two manuals to provide guidance to mining companies on sound practices for the safe and environmentally responsible management of tailings facilities: ???A Guide to the Management of Tailings Facilities; and ???Developing an Operation, Maintenance and Surveillance Manual for Tailings and Water Management Facilities. The Guides were designed to help companies develop and implement tailings management systems that include environmental and safety criteria, to improve the consistency of application of sound engineering and management principles to tailings and water management facilities through their full life cycle, and to demonstrate this to regulators and the public.

May 1, 2003

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By Peter A. Oshust

The EKATI Diamond Mine has successfully completed the development and commissioning of the Panda Underground Project to extract the ore below the Panda open pit. The dominant kimberlite domain of the Panda Underground, intermixed olivine-rich and mud-rich resedimented volcaniclastic kimberlite (RVK), is very similar to the kimberlite domain characterizing the open pit portion of the pipe. A sublevel retreat mining method is in operation underground at Panda; near-vertical blast rings are drilled and blasted into an open void. Broken ore is mucked with load, haul and dump trucks (LHD?s), sized underground then moved to surface through a conveyor system to the process plant. An advanced feasibility study is in progress at the Koala Underground Project. The Koala pipe is geologically more complex than Panda. The pipe below the open pit is comprised of at least five distinct kimberlite domains. There is a 100 m thick zone of incompetent low-grade mud-rich RVK between the open pit and the stable high-grade olivine-rich primary volcaniclastic kimberlite where mining will be initiated. As a result, it is proposed that Koala will employ sublevel caving; each blast ring shot would be confined and mucked in sequence to maintain the cave of the over-lying low-grade RVK ore. The sublevel cave method seeks to safely defer the mucking of the low grade ore to the latter part of the mine life.

May 1, 2006

By Barrie Robb

Outline 1. Mackenzie Aboriginal Corporation (MAC) 2. ACR background 3. ?Learning from Experience? project - What - Why - lessons 3. How Industry could contribute to sustainable Aboriginal communities 4. Concluding words What is the Mackenzie Aboriginal Corporation (MAC)? ? Aboriginal owned ? Established construction capabilities ? Commitment to development of northern resources ? Partners have extensive experience

May 1, 2008

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998