Search Documents

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

The amount of liquid retained in a porous bed is determined by weighing a column containing the bed.The column is attached to the free end of a cantilevered beam, and changes in weight are determined by calibrated strain gauges (which form a resistance bridge) attached near the fixed cnd of the beam. By coupling the output from the strain gauges to an amplifier and a recorder, a continuous record of changes in the drainage characteristics of the bed may be obtained.

Jan 1, 1968

The principles of geometry and trigonometry are so continuously used by mining engineers for the purpose of accurately and intelligibly recording their measurements, that the writer is prompted to lay the following cursory remarks upon mine surveying before the members of this Institution in the hope of eliciting a free interchange of opinion upon details of this interesting branch of the profession. He proposes to deal with surveying only so far as it concerns the mining engineer, not to intrude upon the domain of the professional surveyor, and, in this instance, to discuss more especially that which may be termed the mechanical, rather than the mathematical side of surveying.In the latter part of the eighteenth century and the beginning of the present one, the usual underground surveying equipment in the English metalliferous mines, consisted of a magnetic needle in a fiat square wooden box of about 9-inch sides, a two-foot rule, a long cord, aud a stool, upon which to place the needle and box. The operator took his bearing by sending his assistant with the end of the cord as far in a straight line as the length of the cord would admit.On its being drawn that he held its end in one hand and placed the side of the compass-box against it with the other, and noted the bearing thus found either by a book entry, or by ticking it off with a piece of chalk on the board the compass lay in. He then measured the cord with a two-foot rule. It is needles to say that with these appliances the accuracy of the results were open to question, and mining surveying was not unduly popular.In the present day, engineers have the advantage of using instruments brought to such a state of perfection, and of employing such an exact system of underground surveying, that inaccurate work must usually be attributed either to lack of care, or lack of ability in the operator.

Bacterial Leaching of Complex Polymetallic Sulfide Ore The work described here concerned the study on bacterial leaching of complex sulfide minerals and polymetallic ores operated in shaken flasks and small-scale columns. The bioleaching of jamesonite was not accessible. The iron extraction in pyrrhotite leaching reached 98.2 per cent after 23 days. After 26 days, the zinc extraction of marmatite reached 92.3 per cent while the iron extraction only reached 13.6 per cent. The pulp density had effect on the metal extraction of pyrrhppite and marmatite. For complex polymetallic sulfide ores, after 10 days in shaken flasks, 97.1 per cent zinc extraction was achieved. While after 60 days in small-scale column, the zinc extraction only proceeded to 7.8 per cent; By SEM and EDXA of experimental samples and their leaching residuum, the bioleaching mechanism was discussed.

Sep 13, 2010

By P Lotz

With the recent increase in environmental awareness, gold mining companies are fast becoming signatories of the International Cyanide Management Code (ICMI, 2007). The objective of the Code is to improve the management of cyanide used in gold mining and to assist in the protection of human health and the reduction of environmental impacts associated with the use of cyanide. In particular the code specifies the following cyanide concentration limits: 50 ppm WAD cyanide in a tailings storage facility, 0.5 ppm WAD cyanide for effluents, and 0.022 ppm free cyanide or 0.022 ppm WAD cyanide as surrogate in the post mixing zone of river discharge. Weak acid dissociable (WAD) cyanide refers to those cyanide species liberated at a moderate pH of 4.5, such as HCN(aq) and CN-, and the majority of Zn, Cd, Cu, Ni and Ag complexes with low dissociation constants. It is potentially toxic to humans and animals. Gold plants using cyanide should ideally measure WAD cyanide online and destroy WAD cyanide in excess of the applicable limits to ensure compliance with the Code. Mintek has recently developed an online WAD cyanide analyser (WAD Cynoprobe). The WAD cyanide analysis technique is based on the use of a ligand exchange reagent that liberates WAD cyanide bound to metals such as Zn, Cd, Cu, Ni and Ag. The ligand exchange reaction is represented by the following chemical equation: Metal(CN)X + yLigand ↔ Metal(Ligand)y + xCN- The plant filtrate is treated with a ligand exchange reagent, to liberate WAD cyanide, before measuring the free cyanide concentration via amperometry. The WAD Cynoprobe measures both free and WAD cyanide concentration. Its fast analysis time, approximately five minutes, makes it suitable for use in the control and optimisation of the cyanide destruction and recovery process. The instrument has proven accurate and reliable in the analysis of synthetic copper, nickel and zinc cyanide solutions made up in the laboratory as well as under industrial gold plant conditions during various trials. The WAD Cynoprobe has gained widespread commercial acceptance and is currently implemented on nine gold plants around the world.

Jan 1, 2007

By D M. Frantois-Bongarton

"A few situations are first reviewed where practical shortcuts lead to acceptable solutions where none seemed to be possible. These include: The solving of many complex sampling optimisation problems with the simple approach of the worst case policy (WCP). A simple approach to single-stage sampling problems will be mentioned at continuation. In the plants, minimising the impact of border effects in incorrect samplers, so that the resulting samples are approximately correct and acceptable in practice because the bias risk attached to them is controlled. Examples are given, as well as practical tools and a general methodology.Finally, some sources of undue conservatism are reviewed with general recommendations aiming at eliminating them.CITATION:Frantois-Bongarton, D M, 2012. Practical considerations and shortcuts in sampling, in Proceedings Sampling 2012, pp 171-174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By Haigh J. E

An accurate measure of the earth's magnetic field can be made in a few seconds with the portable proton precession magnetometer. Such an instrument increases the applicability of the long successful method of magnetic prospecting for minerals. As an example of the usefulness of the proton magnetometer, a survey over volcanic rocks near Apsley (Tas.) was made.INTRODUCTIONA completely portable magnetometer whose operation is based on the free precession of polarized protons in the earth's magnetic field, is now available on the market at a price competitive with magnetometers based on the classical physical principles. The ease, accuracy, rapidity, and reliability with which measurements of the earth's total magnetic field can be made with the proton precession magnetometer, led to the try-out of the instrument in an actual field problem so as to evaluate fully the capabilities of the instrument. Such evaluation is important, because the history of magnetic prospecting has shown that whenever significantly improved instrumentation has been introduced, prospecting costs have been substantially cut and many areas in which the prospecting costs were formerly considered excessive in relation to probable returns, have become economic mineral prospects. The proton precession magnetometer offers the possibility of opening up new areas for successful magnetic prospecting.AN OUTLINE OF THE HISTORY OF MAGNETIC PROSPECTINGWhile an outline of the history of magnetic prospecting is not directly connected with the evaluation of a proton pre...

Jan 1, 1963

Ok Tedi Mining Limited has recently completed the first phase of a trial to compare the performance of D26B Krebs cyclones in different configurations to the new Warman 650 mm CAVEX cyclones. From 1992, rougher flotation feed size has increased from the target d80 grind size of 150 ¦m with increasing SAG mill throughput. At high SAG mill throughput, operators have difficulty maintaining the target cyclone feed pressure and must increase the cyclone feed density, thus resulting in a coarsening of the cyclone split. Warman International have developed the CAVEX high capacity cyclone. The new CAVEX cyclones, when compared to the Krebs units appear to:produce a measurable increase in volumetric flow for the same pressure drop; maintain or decrease the proportion of coarse particles reporting to overflow; and lower the overflow density. In all plant trials to-date, the CAVEX cyclones appear to be superior to the standard Ok Tedi Krebs cyclones. Further testwork is planned to evaluate modified Krebs cyclones (with recent design improvements) against the CAVEX cyclones.

Jan 1, 2000

The rapid advance in the adaptation of scientific knowledge to the treatment of ores, resulting in improved chemical and metallurgical processes, has enormously increased the possibility of working lodes profitably, which a few years ago were passed over as unpayable. By the discovery of chlorination, and later of "Cyanidation," by the highly improved methods of concentration, and by the rapid advance in our knowledge of smelting (for which we are greatly indebted to Americanmetallurgists), and by the gradual replacement of scientifing principles and enlightened management, for rule-of-thumb methods formerly in vogue, many large low grade bodies have been opened, and are now paying dividends, which were,twenty years ago, looked upon as hopelessly unpayable. It has been more especially in these large low grade ore bodies, that modern methods have been benefical; for small lodes must be rich to pay at all, as they cannot be worked on the same gigantic scale, but even in these a percentage of metal is saved which formerly was absolutely lost.To make these large deposits remunerative it is, however necessary to try and find the point of greatest economic advantage, to handle the ore in vast quantities, to erect huge plats to treat it, to substitute automatic appliances for hand labour as far as possible, and to combine several processes supplementary to one another, so that ore which is not amenable to one process, shall be saved, by another; and by doing...

Jan 1, 1901

The ore, as sent to the sulphide mill, is a mixture, in varying proportions, of oxidized ore from above the 450-ft. level and sulphide ore from above and below (to date mainly from above) that level. The oxidized ore consists essentially of quartz, with varying amounts of kaolin and clayey material which passes into the slime and, in excess, creates a serious problem in settling. Pyrite may be present in small amounts. The gold is free and extremely fine.The ore, classed as sulphide, consists of pyritic material in a quartz gangue. The sulphides have been exposed to weathering, leaching by descending solutions and attack by ascending gases and actual burning. The alteration products occur in widely varying proportions and this variation adds to the difficulties in settling and control of grinding and flotation.Copper Minerals.-Chalcopyrite is the principal copperbearing mineral with smaller and varying amounts of covellite, which is sometimes associated with chalcocite, both these minerals being apparently of secondary origin.Examination of tailing by Dr. Stillwell has revealed all stages between clean chalcopyrite, chalcopyrite tinged with covellite, covellite with residual cores of chalcopyrite and clean covellite.The chalcopyrite is free floating, very few particles of clean chalcopyrite being observed in the tailing from granular flotation. The chief tailing loss is probably as chalcopyrite occurring as small inclusions in pyrite...

Jan 1, 1939

By Wood W, Bell A

Brown coal production in Victoria's Latrobe Valley Region (Figure 1) continues to rise and currently stands at around 50 Mt per annum. With the exception of around 2 Mt used to produce some 700 Kt of brown coal briquettes, this coal is mined by the State Electricity Commission to fuel large thermal power stations with a total installed capacity of just over 5 000 Megawatts. The moisture content of the coal as mined typically exceeds 60 per cent, making Latrobe Valley coal a markedly low rank fuel. The lack of heating value is, however, compensated for through power station design and by the fact that ash yield is very low, usually within the range of one per cent to four per cent on a dry basis. This means that compared with most other coals, the burning of Latrobe Valley brown coal produces relatively small quantities of waste products and discharges a minimal level of pollutants into the atmosphere. Even so, the inherent quality of Latrobe Valley coal does vary significantly from one area to another (Gloe, 1991; Barton et al, 1992) both on a local and a regional scale. Such variations need to be recognised and understood in order to not only realise efficiency gains in existing power stations but to properly assess resource potential for future utilisation and the application of new technologies. The principal aim of this paper is not to describe coal quality variation in detail or to speculate on the nature of and reasons for such variation. Rather, it is to simply underscore that significant differences do occur and that this is clearly a factor which needs to be considered in any evaluation of Latrobe Valley brown coal as a resource for the future.

Jan 1, 1992

In dealing with the pulverization and treatment of auriferous ores, it may be stated that there is not one system of treatment applicable to all classes. In the southern portion of New Zealand the ores generally contain free gold, with scarcely any impurity that is, it is found in an almost pure state, without any alloy, and its dissemination amongst the matrix is generally in tolerably coarse particles. The only difficulties the mill man has to contend with, are the economical concentration of pyrites, which in some of the lodes are rich in gold, and the extraction of the gold the pyrites contain. In some of the lodes there is what may be termed float gold, that is, the particles of the precious metal are so finely divided that it passes over the quicksilver tables, and, unless there are other appliances for saving it, this class of gold is entirely lost.Indeed it is only within the last five years that any attention has been given, in the southern portion of the colony, to saving the fine gold that has passed the amalgamating tables. In the North Island the ores are very complex there are scarcely two mines, although they may be adjoining each other, where the bullion is of the same character. On every field the gold is alloyed with silver', and in combination with other metals and mineral substances, such as copper, zinc, antimony, galenfl, iron, sulphur, arsenic, etc., and, in some instaaces, cinnabar, as in the case of the Champion lode at Tui Creek, Te Aroha. Ores of this class are extremly difficult to treat satisfactorily.

Jan 1, 1903

In, one stage of the purification sequence of the zinc sulphate electrolyte used at Risdon, cobalt is, precipitated as cobalt nitroso-,B-naphtholate, which is separated from the solution by filtration. Owing to the method of conducting the purification the filter cake contains much gypsum, unconsumed calcium hydroxide, basic zinc sulphate, and entrained zinc sulphate solution, Small amounts of iron and copper that have escaped previous purification steps are also precipitated with the cobalt as nitroso-,B-naphtholate. Thisprecipitate, normally carrying about 18% cobalt, is the raw material for the production of cobalt oxide, cobalt sulphate and cobalt metal.COBALT OXIDEThe main problem in the preparation of a reasonable grade of cobalt oxide from the filter cake is the economic separation ,of the cobalt nitroso-,B-naphtholate from the gypsum. This was solved by the application of flotation. It was discovered that the cobalt nitroso-,B-naphtholate, under correct conditions, would float without any addition agent, giving a relatively high grade concentrate. A plant, was built and has been in operation since 1936. The filter cake is pulped with water and pumped to one of two mechanically agitated tanks, eath capable of holding one day's output. Sulphuric acid is added until the free acid concentration reaches about 3 gm. per litre. Basic zinc sulphate is dissolved and calcium hydroxide converted to gypsum. The pulp, carrying about 2t lb. of solids per gallon, is pumped at a suitable rate to the first of a series of 10 flotation, boxes.. Each box is 3 ft. by 2 ft. 9 in. by 5 ft. deep, and, all have a common, pulp level, since the...

Jan 1, 1949

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By Garnsey R. G T, Wenk G. J, Toop A, Sowerby B. D

A bulk mineral analyser (BMA) suitable for the determination of Cu or Ni in bulk ore samples has been developed at the Lucas Heights Research Laboratories. This analyser, which uses the nuclear resonance scattering technique, is highly specific to the wanted element. The technique has previously been extensively field tested for copper at Mount Isa, Queensland.The present paper discusses the field trial in 1982 of a commercial prototype BMA for nickel. The trial was undertaken at the lateritic nickel mine at Greenvale, Queensland. The BMA and its shielding, together with a laboratory spectrum analyser, were sited in the sample shed adjacent to the workings. Two hundred and thirty-eight ore samples taken directly from the mine blastholes were assayed by the BMA. The average mass of sample was 12 kg, metal contents varied from 0.2 to 3.5 wt/per cent Ni and 4 to 43 wt/per cent Fe and free moisture varied from 11 to 55 wt/per cent. A measurement took 10 min to complete, although this time could have been reduced at the higher nickel grades. The r.m.s. deviation between BMA and chemical assays was 0.09 wt/per cent nickel. Iron and bulk density were also determined by the BMA, r.m.s. deviations being 1.7 wt/per cent and 0.03 g/cmJ respectively. Similar results could be expected from a BMA in routine industrial use at other nickel mines.

Jan 1, 1983

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J M. F Clout

In the iron ore industry significant emphasis is placed throughout the mining process on meeting chemical composition specifications for the export of fine ores, however, little has been published on the implications of ore chemical composition for iron ore sinter and pellet product quality. The ore bulk composition, together with the nature of the minerals in the fine ore both play a critical role in determining the type of high temperature bonding phases that form during sintering and pelletising. This paper uses the experimental determination of phase relations in model sinter and pellet systems such as Fe2O3-CaO-SiO2 (FCS) and Fe2O3-Al2O3-CaO-SiO2 (FACS) to examine the links between iron ore chemical composition and the temperatures used during sintering and pellet firing. The phase relations help to establish the critical thermal and compositional parameters that control the bonding phase chemistry which in turn influences the physical characteristics of the sinter or pellet matrix. Results show that lower Fe-grade (

Jan 1, 2002