Search Documents

The P49 Shaft, Hilton Mine, was sunk and equipped for Mount Ise Mines Limited by con- tractors Cementation - Thiess Joint Venture. The leached siltstones to a depth of 150m were known to contain large volumes of water. These siltstones were cored and tested in the laboratory. Field results confirmed that cement grouting was relatively ineffective but that chemical grouting was effective. The Sm diameter shaft was sunk to a depth of 1040m. Weak strata to the full depth re- quired continuous temporary support by rock bolts and mesh before the concrete lining was poured, and made sinking conditions difficult. After completion of the shaft sinking the headframe was redesigned and modified to allow shaft equipping as a combined service and hoisting shaft with seven compartments. The shaft steelwork was designed and fab- ricated for service with high speed conveyances operating under corrosive conditions. The steelwork, weighing approximately 1500 tonnes, was installed to a high degree of accuracy which required guides not to depart from true verticality by more than 2mm over any 5m, or 15mm over the full shaft depth.

Jan 1, 1976

Although laterite ores already provide a significant proportion of the world's nickel and cobalt production it is anticipated that they will surpass sulphide ores as a source of nickel in the next century. The most recent period of greenfield nickel project construction was during the 1970s when it was notable that all of the eight new plants were based on treating laterite ores. This was because of the relatively large selection of available high grade laterite ore deposits amenable to cheap open cast mining and a paucity of high grade sulphide ore prospect alternatives. Of the three processing options for treating laterite ores: 1. smelting for the lower horizon saprolite ore, 2. ammonia; and 3. acid leach for the upper horizon limonite ore, smelting currently accounts for about 80 per cent of nickel production. In the future, as saprolite ore grades decline because of relatively high exploitation rates, the incentive to process the large untapped reserves of limonite ore will increase. The high cobalt content of limonite ore also makes it ideally suited to processing by a hydrometallurgical rather than smelting route. With only two exceptions, all saprolite smelting operations have a Class 2 nickel end product (largely ferronickel) and do not produce a cobalt by-product. As a result of technological advances, the modified ammonia leach process for limonite and transition ore as undertaken at Yabulu, now allows the production of pure nickel metal as a Class 1 product, along with significant tonnages of cobalt by-product. The mixed Ni-Co sulphide intermediate product of the pressure acid leach processing of limonite ore at Mon is converted to Class 1 nickel and cobalt metal at Fort Saskatchewan, Canada.

Jan 1, 1996

By D J. Cronin

Alcoa World Alumina AustraliaÆs Huntly and Willowdale bauxite mines are located in the Darling Range of South Western Australia, which places their operations within PerthÆs surface water supply catchments. These catchments supply Perth with its highest quality drinking water. With the decreasing rainfall trend of recent years catchment yields to water supply reservoirs have reduced to such an extent that water use restrictions were necessary in Perth for 2001, 2002 and 2003. Protection of catchment water quality and water use conservation are crucial issues for AlcoaÆs operations within the Darling Range. Alcoa has been conducting bauxite mining activities in water supply catchments since the mid-1960s. During that time Alcoa has worked closely with the relevant State Government water and environmental agencies to ensure that its operations do not adversely impact catchment water yield and water quality. Monitoring and research have shown that Alcoa has the necessary environmental management systems in place to ensure it can continue to operate in a sustainable manner within water supply catchments. AlcoaÆs mines reduced the volume of water taken from public water supply catchments by 24 per cent in 2002, compared with 2000. This success has had an added benefit; Alcoa does not need to develop a new water source for its Huntly Mine. The conservation measures implemented to reduce water use include: increasing water recycling, using chemical additives for haul road dust suppression, conducting water audits, reducing water demand, monitoring water use, promoting water use targets and training staff in water conservation.

Jan 1, 2003

The JORC Code, which has been in existence as a Code incorporated in the listing rules of the Australian Stock Exchange and New Zealand Stock Exchange since 1989 and 1992 respectively, has been revised and will be re-released in 2003. This revision followed a call for submissions in December 2001, the publication of an exposure draft in late-2002 and an exposure period during which a large number of constructive comments were received. These comments were reviewed and a further exposure draft released as part of the current exposure draft of the ASX listing rules. It is anticipated that the final Code will be incorporated into the stock exchanges listing rules in late-2003. The 1999 JORC Code has been the standard on which other reporting Codes have been based, each of which has contained refinements. Three in particular, the Reporting Code from the United Kingdom/Ireland/Western Europe, the new Canadian Reporting standards and the SAMREC Code from South Africa, influenced JORC in the preparation of the 2003 JORC Code. Whilst there are differences between the 1999 Code and the 2003 Code, these changes are mainly in the guidelines. The Code definitions, which are largely in accord with agreed international definitions, remain substantially unchanged. The two main changes in the 2003 Code are the requirement for a Competent Person to be responsible for the documentation relating to the reporting of Exploration Results, and the introduction of æRecognised Overseas Professional OrganisationsÆ as overseas organisations to which Competent Persons may belong. Other changes include: clarification of the reporting of exploration targets or potential; the rearrangement of the diamond reporting clauses; the introduction of guidelines for the reporting of Industrial Minerals; modification of the coal clauses and recognition of the new Coal Guidelines; and the introduction of a guideline encouraging the discussion of relative accuracy and confidence in resource/reserve estimates. Other lesser changes to the Code are listed and discussed briefly. The release of the 2003 JORC Code maintains the standard set by JORC as a world leader in the development of mineral reporting Codes and their adoption by industry.

Jan 1, 2003

In general the iron ore industry has been slow to adopt the Whittle Pit optimising software in the evaluation of iron ore deposits. The reasons for this are two-fold:the iron ore industry has developed techniques, usually bespoke software residing in the corporate offices of the respective iron ore companies, to establish their final pit limits; and the fact that the Whittle software doesnÆt easily lend itself to estimating a sales product of constant quality without maximising grade (metal content). The Whittle software is based on the work done by Lerch and Grossman (in the early 1970s), which proposed that graph theory be used to establish an optimal surface that maximises the revenue from a deposit. The maximised surface created in the pit optimiser is translated into a proposed optimal final pit shape that can be used by the mine design engineers as a target outline to lay out the final practical pit. By treating a geological and ore resources model that was created for an iron ore deposit as a subset of the recoverable resources estimation (RRE) type of geological models, the evaluation of an iron ore deposit and establishing the final pit is greatly simplified in the Whittle 4-X optimiser. Instead of trying to optimise the iron content of the deposit, the emphasis swings to maximising the extraction of a finished and saleable iron ore product. This is achieved by treating the finished saleable iron ore as an element in the multi-element Whittle optimiser. The quality of the finished sales product is represented, and the material that cannot be used in the blended product is also shown. Proposals for enhancing the functionality in the Whittle 4-X optimiser to make the evaluation of iron (and coal) deposits easier includes the creation of a new reporting function that will allow the user to specify which field(s) can be used as the divisor(s) for the reporting of the element grades in the model.

Jan 1, 2007

By Jensen B

The approach of using the Coward Triangle for the analysis of flammable mine gas mixtures has been examined for its application, to the flammability of coal dust/gas/air mixtures. Explosible lean limit and rich limit concentration data for dust/methane/air mixtures are examined and illustrated using co-ordinate geometry. It is concluded that a three-dimensional envelope representing hybrid explosible mixtures can be drawn. The dimensions of this explosive zone will vary with the characteristics of the coal dust and the gaseous composition of the mine atmosphere. Further research is needed to establish these dimensions for important mined seams.

Jan 1, 1994

This paper examines the broader implications of recent and ongoing changes in mineral resource managementå and reporting practices and the impact that these might have on mining companies. It is likely that an International Reporting Code will be developed in the near future, based on a number of National codes produced in recent years. However, this is only part of the reporting story, as an International Code brings with it a range of further issues to resolve. For the Code to be effective, there needs to be international recognition and perhaps licensing of Competent Persons and an expanded base of sponsoring professional bodies. Also, in an increasingly global business, shareholders, regulators and other interested parties need to know and understand the general processes involved in resource and reserve estimation and reporting in order to recognise companies that maintain the highest standards. There is a current trend towards greater scrutiny of company performance in a range of areas under the banner of corporate governance, and many changes are happening that will place greater disclosure burdens on all companies in the future. Good corporate governance means management of company assets for the benefit of the stakeholders. For a mining company, there is no greater asset than its mineral resources and reserves and directors are just as responsible for effective management of their mineral resources as they are for financial good practice. The paper looks at the relevance of corporate governance principles to mineral resource management and the changes that this could bring to the way that companies deal with regulators, shareholders, financiers and others. Finally, increased scrutiny and further regulation inevitably means greater effort by the industry and higher costs. Despite this the author believes that there are substantial offsetting benefits to be gained by companies prepared to take the initiative in improving resource management practices and communicating these improvements to shareholders. In order to achieve the benefits however, the industry needs to fully engage in the changes that are taking place û setting its own standards and working with the regulators rather than sitting back and being legislated against. Mineral resource reporting provides a good model of how this process can work and there will be other opportunities in the coming years as the industry seeks to develop best practice in mineral resource management. The author is an employee of Rio Tinto but wishes to point out that the views expressed in this paper are his own and not necessarily those of Rio Tinto.

Jan 1, 2002

By E P. Nelson, R Gutierrez, P W. Layer

The San JosT district in Patagonia comprises a number of epithermal precious metal quartz veins hosted by a Mesozoic volcanic sequence. New radiometric data indicates that upper Jurassic volcanism was closely followed by vein mineralisation in the lower Cretaceous. A structural model is discussed for the district at times of mineralization that may also apply on a regional scale and other mineralised districts in Patagonia. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Oversby B, Wellman P, Wyborn D, McPhie J, MacKenzie D

The Bureau of Mineral Resources (BMR) and the Queensland Mines Department are engaged in integrated regional- and deposit-scale studies in the Burdekin Falls-"Conway" area, about 100km southeast of Charters Towers (Fig. 1). The regional work augments recent mapping in the Mount Coolon area farther south (Hutton et al., in prep.). These studies are aimed at improving understanding of gold mineralisation and its geological setting in the Drurunond Basin and associated rocks. Knowledge of the regional stratigraphic- structural framework and setting of mineralisation has until now been based on investigations dating from the early to mid 1960's (mainly Bowen 1:250 000 Sheet; e.g. Paine et al., 1974; Wyatt et al., 1971), and on regional syntheses (Olgers, 1972; Levingston, 1981). Some recently explored epithermal gold occurrences in the region have been interpreted on the basis of this early work as being hosted by the Late Carboniferous Bulgonunna Volcanics. The objective of our field research was to refine the regional geology, paying particular attention to the Bulgonunna Volcanics. The results summarised here indicate that unnamed Devonian-Carboniferous volcanics (DCv) of the northern Drummond Basin and mid to late Palaeozoic granitoids are much more extensive, and the Bulgonunna Volcanics much less so, than was previously recognised.

Jan 1, 1989

Wrenching between basement blocks is considered to be the mechanism whereby a well developed set of en echelon folds and an associated fracture system are developed in the Fitzroy Depression, Western Australia. The regular geometry of these structures accords with a right lateral regional coupling between high-standing, basement blocks bounding a trough filled with a thick pile of stratified Phanerozoic sediments. The structures developed during or after the Mesozoic Era, but the couple is inferred to have been applied to blocks outlined by old lineaments, which may reflect strains or ruptures in basement that developed during the Precambrian, and which were regenerated during Palaeozoic and Mesozoic time.

Jan 1, 1967

The economic viability of base metal and gold production projects at Chillagoe, North Queensland has been elusive or difficult to achieve. Because of isolation and low grades metallurgical efficiency has always been essential. This paper, concentrates on the Chillagoe Railway and Mines Company's operations from 1898 to 1914 and Elders Resources Limited's current developmental operations at Red Dome. The technological methods of concentrating, smelting and refining the copper, silver, lead and zinc by the Chillagoe Company will be outlined as well as their understanding of the geological aspects of the ore bodies and the stock market speculation. The Chillagoe Company failed in its economic management but developed the region. Elders Resources have successfully redeveloped the region including fostering the tourist potential of the area through their expert financial, engineering and metallurgical strategies within the external economic parameters of the Pacific Region.

Jan 1, 1987

Extensive geophysical exploration and drilling operations have been: conducted in, South Central Queensland by Phillips Petroleum Company and Sunray DX Oil Company since late 1959. The main outlines of subsurface geology are now known, but many problems must be solved before a comprehen sine. picture can be presented of the geology and petroleum prospects e Interpretations to date suggest that -fiddle Paleozoic sedimentary rocks, probably, related to the Tasman belt of geosynclines, once extended. over. most. of the area An oro;eny 2.n late Paleozoic time, succeeded by deep pre-Pexmian erosion, removed the older sediments over large. areas, but Paleozoic sediments, were preserved from erosion in the Adavale and ancillary structur-a.l basins. Marine sediments of Devonian age are con-sidered prospective source beds for petroleum. Current work is directed toward finding favorable structure and reservoir beds to test the oil prospects of the area.

Jan 1, 1962

By Basillo CI

The adsorption mechanisms of various thiol collectors can be subdivided into four classes: chemisorption, EC-mechanism, catalytic oxidation and metathetical substitution. The chemisorption mechanism occurs at potentials below the thermodynamic potentials for the metal-thiol compound formation and is reversible. The EC-mechanism occurs when the mineral is sufficiently oxidised to liberate metal ions to form metal-xanthates; therefore, it is observed with more easily oxidisable minerals and/or with collectors having large pK values. Thionocarbamates adsorb on sulphide minerals via the EC-mechanism due to their large pK values. Although the adsorption occurs at very low potentials as compared to xanthates, it is irreversible with large overpotentials. On the other hand, the adsorption of modified thiophosphates and thiophosphinates occurs near the thermodynamic potentials because of the low pK values. The metathetical substitution is believed to occur only when a mineral is highly oxidised. These classifications are useful for studying the effects of electrochemical potentials and the molecular structure on the collector adsorption Mechanisms.

Jan 1, 1993

By Clark IH

Numerical modelling is an effective aid for the planning and design of underground coal mines. With funding from the National Energy Research Development and Demonstration Program, CSIRO Division of Geomechanics has produced a workstation environment which will allow the Australian Coal Mining Industry access to a wide range of numerical design models. The emphasis is on usability and simplicity and the long-term aim is that the techniques should be used routinely at the mine site, so that, in the future, design of a new underground mine will routinely involve modelling of each proposed layout.Each of the five numerical analysis programs, FESOFt, FLAC, MNLAY, FEBLK and UDEC has both strengths and weaknesses. Some analyses with each program demonstrate areas when; observed in situ behaviour in underground coal mines has been successfully modelled, and the results of site monitoring provide a basis for comparison with the predictions of numerical models.

Jan 1, 1991

By T Tran, F Lucien

Supercritical fluids (SCFs) have gained recognition as solvents for the extraction of a wide range of organic materials. Their principle advantages over conventional organic solvents are that they possess much more favourable transport properties and that such properties can be easily altered by adjusting the system temperature and/or pressure. More recently, SCF solvents have been employed in the extraction of metal ions. The direct extraction of metal ions using SCFs such as CO2 is normally not possible due to the charge neutralisation requirement for solubilisation. However, extraction can be achieved with a SCF solvent containing an organic complexing agent as a cosolvent (Laintz et al, 1992; Laintz and Tachikawa, 1994; Dehghani, 1996). The role of the SCF is therefore similar to the role of a diluent in conventional liquid-liquid or solvent extraction processes. In this regard, SC-CO2 is a particularly good diluent since it exhibits good solubility for many organic complexing agents. The extraction of metals with SCF solvents has been examined mainly in the analysis of environmental samples and the treatment of metal contaminated wastes. Nonetheless, some interesting results have been reported recently on the extraction of rare earth metals, which highlight the potential of SCF solvents in mineral processing applications (Laintz and Tachikawa, 1994; Dehghani, 1996).

Jan 1, 2000

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

By S Vink, V Nanjappa, C J. Moran

Poor quality water resulting from interaction of surface run-off with saline mine spoil and soils can cause significant problems for water reuse on mine sites. Not only can this saline water lead to machine corrosion and increased maintenance costs, but may cause detrimental effects on the environment. Determining the geochemistry of mine spoil, and the likelihood of salt dissolution during rainfall events, may aid in more effective mine site management of water. Spoil samples were taken from three areas of the German Creek mine site, situated in the Bowen Basin coalfield, Queensland. Samples from two undisturbed areas on the lease were also collected for comparison. Analyses were performed using a variety of laboratory techniques: leaching tests, effective cation exchange capacity determination, X-ray diffraction, clay quantification, and total organic content determination. Results show that dissolution of surface (top 2 cm) salt minerals from spoil areas is an important contributor to surface run-off salinity during rainfall events. Equally, ion exchange with clay minerals appears to be a significant source of elevated ion concentrations in run-off waters. Findings from the undisturbed areas show undetectable quantities of salt mineral species, resulting in waters with low ion concentrations. More generally, monovalent cations (sodium, and to a lesser extent potassium) appear to be derived from dissolution of salt precipitated whereas divalent cations (calcium, magnesium) are more likely to be sourced from exchange reactions with clay minerals. Incorporating knowledge about the mechanism of cation mobilisation from spoil with the spatial distribution of spoil properties and understanding of the dynamics of water quality variations on the site will aid in development of integrated water quantity and quality management strategies.

Jan 1, 2009

Geochemical investigations carried out in the Woodcutters area, Rum Jungle district, NT., consisted of a programme of C-horizon soil geochemical sampling followed by rotary-percussion and diamond drilling.Comparison of detailed geochemical sampling with the original broadly-spaced sampling showed that the structures along which the orebodies occur are reflected very closely by the detailed sampling.A series of vertical rotary-percussion drill holes put down adjacent to a gossan revealed a broad layered dispersion of lead and zinc in the deep lateritic weathering profile, while primary dispersion haloes are only very narrow. The layering appears to be related to the weathering profile.

Jan 1, 1978

By M Lellis

During the last decades, maintenance has changed from an ordinary repair activity to a complex function that plays an essential role contributing for the companyÆs results. The increasing level of complexity of modern equipment motivates maintenance personnel to improve both techniques, and management systems, in order to face the new challenges. Managing properly those modern means of production requires knowledge of methods and planning systems, controlling and performing maintenance tasks, in such a way that two objectives are achieved at the same time: system efficiency and cost-effectiveness. This paper shows CVRDÆs experience on evolving and implementing a model to plan and manage maintenance activities in order to achieve a higher level of performance on its operations.

Jan 1, 2003

By Smith G. A

The scope and complexity of the Melbourne Underground Rail Loop Project and the budget restraints on the planning, design and construction of the works necessitated sound manage- ment procedures for control and co-ordination. Project Management Procedures formulated by the Principal Consultant to the Authority, John Connell - Mott, Hay 9 Anderson, Hatch, Jacobs, ensured that the Authority retained overall control of the project at all times.

Jan 1, 1981