Search Documents

Estimation of operating costs in the nickel production industry requires a detailed analysis of material flows from mine to smelter to refinery. Despite the small number of nickel producers compared to other base metals, the existence of two very different ore types (sulphide and laterite) and a wide variety of mining and processing technologies make the identification of these flows of critical importance if an accurate global picture is to be obtained. Smelting and refining processes in nickel metallurgy have evolved with a high degree of adaptation to specific operating conditions in different locations. Overall costs are calculated by combining individual cost elements for each unit in production chains from mine to saleable metal product. The average cost of western world primary nickel production in 1995 was US$2.07/lb ($4560/tonne). Average operating costs remained virtually unchanged in the three years to 1995 after an 8.5 per cent fall in 1993, but a 3.9 per cent increase to $2.15/lb is expected for 1996. A major factor in this rise results from the lower prices of copper and cobalt this year, reducing the by-product credits available to major producers.

Jan 1, 1996

Acclaimed as one of the most remarkable orebodies anywhere on account of its length and richness, the Oroya Shoot occurs on the eastern side of the Kalgoorlie gold mining district close to the contact of a fine-grained with a coarse-grained greenstone, and in association with sediments. In the same stratigraphic position on the synclinal flanks of a large drag fold there are a number of other flat ore pipes, smaller, but almost as rich in tenor. Although differing in control structure they are believed to be related genetically as all show a characteristic development of a bright-green ore known locally as "green leader". Folding and bedding structures have played an important part in formation of the ore shoots.INTRODUCTIONThe Oroya Shoot is the biggest individual bonanza of Kalgoorlie's Golden Mile. It has been stoped almost continuously over a length of 4,300 ft., and about 2,000,000 oz. of gold have been won from it. Naturally pillars are not left in the best sections of such an orebody and the detailed geology of stoped out portions can only be inferred from examination of adjacent workings.No mention is made in the literature of the actual makeup of the orebody although a few structures are shown on some of the old cross sections. A diagrammatic cross section, Fig. 1, adapted from Stillwell (1929) illustrates the form of the Oroya Shoot.Gustafson (1937) drew attention to the role of folding, previously unrecognized, in Kalgoorlie geology, and indicated that the Oroya Shoot is associated with a minor drag fold on the east limb of the Brownhill Syncline, itself part of a larger left hand drag on the Central Anticline. The latter in turn appears to be part of a regional right hand fold system as shown by Campbell (1953).

Jan 1, 1959

By Urabe T

In June 1989 a diving cruise of the French submersible Nautile has been carried out on the North Fiji basin spreading ridge. The objective of the cruise was the geological and geochemical study of the active spreading axis and associated hydrothermalism processes. This operation was the third cruise of the French-Japanese STARMER project following two cruises of the R/V Kaiyo in 1987 and 1988.INTRODUCTIONAfter the Seapso III cruise (Auzende et al., 1986, 1988a and b) of the R/V Jean Charcot in 1985, the objective of the Kaiyo 87 and 88 cruises was the complementary Seabeam mapping of the North Fiji Basin spreading axis between WS and 22'S and a systematic sampling (water and rocks) and deep towing (TV and photos) at about every ten milles along the axis.

Jan 1, 1990

By White B

The domestic and commercial use of underground space dates back to Neanderthal man living in caves. There are many examples worldwide of the imaginative use of underground excavations, either left by mining or purpose-built. World living trends indicate that an increasing percentage of the population is living in and around major cities. Environmental, social and economic pressures associated with urban expansion can be partially catered for by a well-planned and integrated underground space regime. This paper addresses the types of underground development that are complementary to the economic and environmental pressures associated with urban expansion and high density cities. The paper explores the implications of mining and exploration technology and civil engineering, as well as the ancillary professional disciplines (legal, architecture and planning, sociology and education).

Jan 1, 1997

By Biao Q, Mizuta Y

Thermal constants such as thermal con- ductivity and thermal diffusivity of rock and coefficient of heat transfer of airway wall are the most important characteristic values which decide accuracy of prediction calcula- tion. However, quality of rock is not homoge- neous and water content in rock varies with location and so, a method for in-situ measure- ment of thermal constants must be taken in. The method developed by us is to measure in- situ rock temperatures at two different depths from airway wall. It is simple and we found its accuracy is good enough in the engineering Sense.

Jan 1, 1988

By Low Russell

Mark Westfield, writing in The Australian on 16 May 1994 stated: The role of the independent expert is crucial to Australia's investment system. When it falls down, there can be very dramatic consequences. The scope of these consequences was dramatically illustrated in the decision of Rogers J. at first instance in Cambridge Credit Corporation v. Hutcheson (1983) 8 ACLR 123 when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million, well in excess of their insurance cover. No comfort should be sought in the fact that this decision was overturned on appeal, for the result of the appeal rested on whether there had been a causal connection between the breach of contract which had occurred and the loss suffered, rather than on the fundamental principle of auditors' liability. Thus: Those who prepare experts' reports in company cases carry a heavy moral responsibility, whatever their legal duties may be... Unless high standards are observed by those who prepare these reports, there is a danger that systems established for the protection of the investing public will, in fact, operate to their detriment through reliance placed on those reports and on the reputations of those who furnish them. In lending his name, the expert will often, as in this case, be lending a name to conjure With.

Jan 1, 1995

By C Wels

Current best management practice requires the placement of a cover onto most types of mine waste including tailings, waste rock and/or spent heap leach rock at closure of the mine. The objectives of a cover system may vary from site to site but generally include dust and erosion control; chemical stabilisation of acid-forming mine waste (through control of oxygen ingress) contaminant release control (through control of infiltration); and/or provision of a growth medium for establishment of sustainable vegetation. In our experience, there has been a general tendency by stakeholders to develop performance criteria for cover systems, which are tied directly to these specific design objectives. In many cases, this practice has led to the development of single, often very conservative, numerical values of cover performance criteria such as ænet percolationÆ, ærate of oxygen ingressÆ and/or æplant density/mixtureÆ. In our opinion, there is a need to develop cover performance criteria on a case-by-case basis and with due consideration of the short-term and long-term impacts on the receiving environment at a particular site. This paper puts forward a methodology for developing site-specific performance criteria for a cover system designed to isolate acid-forming mine waste and to control acid rock drainage. The proposed methodology links the predicted performance of a cover system to groundwater and surface water impacts. This way, the appropriate level of control (of oxygen ingress and/or net percolation) required by the cover system can be determined. A case study is presented that illustrates the application of the methodology proposed in this paper.

Jan 1, 2003

With the exeption of the United States, Canada and Russia, oil has not been around in quantity near world centres of population. Production: in Western Europe is insignificant. Japan is without production as are Australia, Southern Africa, India; Brazil, Chile, New Zealand and China. The United States is, however, a large importer of crude oil. The very fact that oil is produced generally away from centres of population means that it has to be carried by sea to the area in which it is required. There is, therefore, a constant flow of oil around the world in very definite channels.

Jan 1, 1962

It may at first sight appear somewhat presumptuous for the writer to attempt to discuss a subject in which he cannot pretend to possess any special scientific training; but a sufficient apology can surely be found in the fact that a very large percentage of the accidents from explosives occurring in metalliferous mines is traceable to the ignorance of the characteristics of these compounds by the miners who have to handle them, and to their deliberate disobedience of the rules laid down for their guidance by the manufacturers, the government regulations, or the special rules of the mines.The only method which promises any possibility of improvement upon these conditions is to substitute reason and understanding for the rule-of-thumb principle which says "you should do this" or "you should not do that." In the one case his own knowledge and intelligence enables the miner to avoid any dangerous practice in the other his inclination prompts him to do anything which will save time, provided he is not found out or at best trusting to his memory to tell him what is dangerous, without the reasoning which makes that memory easy.Another evil of rule-of-thumb knowledge is that, from its very nature, it prevents adaptability, and so we find that old miners, who learnt blasting in the days of black powder, cannot understand why high explosives do not require heavy tamping, or because copper bars are permitted in tamping powder they should not be used with other explosives...

Jan 1, 1903

By T J. Sheer

Water vapour refrigeration (systems using water as the refrigerant) could potentially be used to provide chilled water at underground locations in mines, as an alternative to conventional refrigerators using refrigerants such as R-134a. The use of water as both the primary and secondary refrigerants is attractive in concept since direct-contact heat exchangers could be used, yielding higher coefficients of performance. The disadvantage of water is the very high specific volume of the vapour at low pressures, which leads to great challenges in compressor design, as has been reported previously in the context of slurry-ice plants for mine applications (Ophir and Koren, 1999). Steam ejectors have long been known as alternative compression devices for refrigerators, but no work has been done previously on the possibility of using ejectors powered by high-pressure water, which is readily available in mines from long pipe columns in vertical shafts. This paper presents the results of a laboratory investigation into the use of high-pressure water as the motive fluid in an ejector refrigerator. No previously reported liquid ejector system has achieved subcooling of the process fluid, ie a reduction in fluid temperature within the evaporator to a level below that of the motive fluid. In contrast, the present work demonstrated that subcooling could occur at motive water pressures above 5 MPa. Mine cooling applications were considered and it was concluded that while this concept would not be feasible as a mine-wide cooling source, there could be specialised applications where it would be beneficial. One application would be to cool backfill and thereby reduce the heat load at the working face. In this case the best performance would be achieved by using the ejector in combination with an energy recovery system such as a Pelton turbine or a three-chamber pipe feeder.

Jan 1, 2005

The comparatively low winter rainfall, exposure to heavy salt laden coastal winds, and the consequent high evaporation rate, are important considerations in the rehabilitation of the Maslins Beach Sand Pit. The deficit of rainfall over evaporation is assessed at 1085 mm per annum. Such a coastal environment complicates the establishment of plants. The endemic flora found on the Sand Pit environs is mainly low wind-planed shrubs and mat plants. The dunes near the coast support an association dominated by Atriplex cinerea, Spinifex hirsutus, Scirpus nodosus, and Olearia axillaris. The coastal cliffs carry a more diverse vegetation dominated by Beyeria lechenaultii and Eutaxia microphylla. Overburden is used to develop a new landscape to screen operations, batter final faces, and cover rubbish at the nearby Council dump. The early overburden dumps were built with little regard for stability, but the more recent practice of using scrapers has resulted in more stable dumps. The erosion problems created by poor compaction have been controlled by contour banks, diversion drains, bitumen lined run-off drains, and hay mulching.

Jan 1, 1976

By George G

The Circum-Pacific Map Project is a cooperative international effort to prepare and publish geological, geophysical and mineral resource maps of the Pacific Basin and adjacent land areas. Earth scientists representing 180 organizations from more than 40 Pacific Rim countries are participating in the work. The project is directed by a committee established 14 years ago as an activity of the non-profit Circuin-Pacific Council for Energy and Mineral Resources. Technical and cartographic support is provided by the U.S. Geological Survey. The Circum-Pacific Map Project is organized under five regional panels of experts on the geology and resources of the four quadrants of the Pacific and Antarctica. A series of five 1:10,000,000-scale regional maps and a 1:17,000,000-scale map of the entire Project area, the Pacific Basin Sheet, provide the cartographic base. Forty-eight individual sheets are planned and thirty have been published in eight different series, including base maps, geography, plate tectonics, geology, energy resources, mineral resources, tectonics and geodynamics. Additional special single-sheet thematic maps on the Pacific Basin base have been published and are planned for a total of more than 50 individual sheets.

Jan 1, 1987

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

A considerable debate has arisen regarding the best route for the beneficiation of iron ore. Supporters of jigging technology claim that although the technology is old, due to recent advances in jig control and a better understanding of the separation processes within jigs, it offers significant advantages over dense medium separation, especially in terms of reduced capital and operating costs and simplicity of design. Supporters of dense medium separation claim that this technology is proven to provide the best possible separation and that the gain in efficiency over the life of the plant, compared to that of a jig, will more than offset any differences in capital or operating costs. The truth is that both viewpoints are valid and that the choice is ultimately determined by specific characteristics of the ore being treated. Factors that need to be taken into account in deciding upon the correct option include the size/density distribution of the ore to be treated, the different size fractions which must be treated (lumpy or fines), differences in yield at grade, plant layout and capital and operating costs. Each of these factors will be discussed in detail and a case study for both lumpy and fines will be presented.

Jan 1, 2007

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By Ryan CG, Cousens DR, Suter GF, Griffin WL

A novel method utilizing PIXE with microbeams following fire-assay has been developed to determine PGE and Au at sub-ppm levels suitable for application in exploration. Analyses of the prills from the lead and silver fire-assay yield Pt, Pd and Au concentrations readily. NiS must be used as collector if the complete suite of PGE is required, but this method is not as Convenient.

Jan 1, 1989

The Olympic Dam mineral discovery by Western Mining Corporation (WMC) in South Australia has been shown to contain one of the world's largest known deposits of copper and uranium; gold and silver are also present. Development of the deposit jointly by WMC and the BP Group is awaiting commitment, with planning based on initial production of gold in 1987 and copper and uranium in 1988.

Jan 1, 1985

The, Ore-bodies.-The ore-bodies of the North mine, North Broken Hill Ltd.; consist of two lenses, connected by a narrow neck of mineralized country. They pitch at an angle of 40° in an easterly direction and dip north at 60° to the horizontal. The southern ore-body, on a horizontal plane, has a total maximum length of 800 feet and in one place attains a width of 230 feet, whilst the northern orebody has a maximum'length of 600 feet and a maximum width of 80 feet.

Jan 1, 1940

By J Burgess, G Scanlan

In 1993 after over 110 years of mining operations, production ceased at the Broken Hill North Mine. Following the cessation of operations a rehabilitation program was developed to satisfy the requirements of the various government departments. This program has been implemented progressively since mine closure. The paper will discuss: primary aims and objectives of the rehabilitation program, implementation of the program, rationale behind rehabilitation objectives, and problems encountered in implementation of the program. To-date the primary rehabilitation of the mine has involved the capping of redundant tailing dams with inert waste rock to prevent the contamination of the receiving environment. A Water Management Plan has been developed to contain all run-off from the mine area in an extreme storm event. A cultural heritage assessment of the leases has been undertaken to ensure the rehabilitation is consistent with the historical significance of the site and community expectations. All redundant material from the mine has been sold in a æno reserveÆ auction and the workshop area has been relocated to the Southern operations. At present the only active areas on the mine are a maintenance area for equipment for the Potosi open pit, and a primary crusher for Potosi ore which is railed to the Southern operations for further processing. Upon completion of the rehabilitation program, Pasminco Broken Hill Mine intends to relinquish the mining leases to the Department of Mineral Resources.

Jan 1, 1998