Search Documents

By B Shen

The Wambo Rail Spur located near Singleton, New South Wales, Australia, runs for approximately 14 km linking the Mt Thorley rail loop and the Wambo Coal Mine. The project involves a 260 m long tunnel in weathered sedimentary and intrusive materials. The tunnel has a low cover and runs under a main highway. This second paper on the project looks into one aspect of the tunnel in detail: the use of shotcrete arch as the primary support for part of the tunnel excavation. The use of shotcrete instead of steel arch, formulation of the material specification, construction sequencing, installation at the excavated face and material testing for verification related to this facet of the project will be discussed in this paper. The tunnel opened in April 2006, and two years on, we briefly reflect on the impact of this design decision on the overall project.

Jan 1, 2008

SINCE writing the above-mentioned paper, some further indicator cards have been taken from the No. 1 machine, and the writers believe that a reproduction of these cards will be interesting as illustrating the performance of the machine after fifteen month steady running, night and day, seven days per week and twenty-four hours per day, at the average speed of fifty-seven revolutions per minute (see Fig. 1, page 60). For the past twelve months no adjustment have been made in the valve setting, and the only repairs have been in connection with the springs of the poppet valves, and these but slight, the springs latterly having been removed. The cards illustrated were taken with one indicator, and, therefore, are not simultaneous, andmay show to some extent the yariations of individual strokes, and with that qualification may be taken as typical of the machine's average performance.In connection with some feed-water measurements of the winding engines a rough test was run with the two compressors, the Riedler and the Corliss, coupled to the condenser, and running at fifteen and fifty-seven revolutions per minute respectively, with the result of 15.9 pounds of steam per indicated horse power per hour. This result, though only approximate, seems to indicate that the No. 1 machine is running under the guaranteed consumption, and that it is capable of maintaining this under the severe conditions of everyday practice.

Jan 1, 1909

By Corbett GJ

Epithermal gold-silver deposits occur in young volcanic terrains where post-mineral cover commonly impedes the search for mineralisation. At the Togi Project in Honshu, Japan, a complex mineralised system is largely covered by post mineral volcaniclastics. A combination of high resolution electrical resistivity surveying and detailed airphoto interpretation has, with close geological control, enabled synthesis of structural and alteration characteristics of the Togi geothermal system, in turn permitting ranking of the prospects for drill testing.

Jan 1, 1990

By B Hall

The authors have undertaken many independent mine optimisation and operational improvement projects at Australian and international mining operations over the past decade. This work has provided an understanding of the underlying practices responsible for the good long-term performance of some operations, and the failure of others to achieve their objectives. Good long-term performance, and value creation can be achieved through a logical and rigorous process of identifying the optimal mine plan (æThe PlanÆ) that delivers the corporate goals, establishing appropriate performance measures that are aligned with these goals, and ongoing monitoring of compliance with the established targets to ensure the operation reliably achieves The Plan. A number of practical methods have been developed and implemented to assist mining operations deliver their corporate goals. This paper outlines some of these methods, providing some fundamental guidelines that will assist in the establishment, and reliable achievement of The Plan that delivers the corporate goals.

Jan 1, 2006

A novel solvent extraction process, called the SOHNEX process, has been developed at the University of Utah. In this process, the organic and the aqueous phases flow countercurrently in a horizontal vessel, and the emulsion between the two liquid phases is generated by high-velocity gas jets injected at the bottom. The gas jets are located at certain intervals along the bottom of the vessel with phase disengagement zones on either side of the plume zone created by the gas jet. The system is simple, having no mechanical moving parts or complex internal structures, and yet provides good contact between the phases with minimal backmixing. Tests have shown that emulsions with a wide range of specific interfacial area, including that typically encountered in mixer-settlers, can be generated in this process. It has significant built-in flexibility of operation including the control of the flowrate and hold-up of each liquid phase. The SOHNEX process overcomes the difficulties in the operation of conventional solvent extraction equipment such as mixer-settlers and column extractors. A major advantage of the SOHNEX process is that the energy of mixing can be closely controlled by adjusting the strength of the gas jet. This allows an optimal control of the drop-size distribution of the dispersed phase and thus the specific interfacial area. The process is continuous, and any number of extraction and separation stages may be built into a single vessel. The gas can be recirculated in a closed loop, thus eliminating solvent loss and mist problems, especially for high-temperature operations. The SOHNEX problem can handle solutions that contain suspended solids and that form third phases. The simplicity of the equipment and operation with low maintenance will mean much reduced capital and operating costs as well as low environmental risks and improved safety. The SOHNEX process has been tested for continuous copper extraction from a dilute solution. Calculations also showed that uranium and other radioactive elements can readily be extracted in a small unit of the SOHNEX extractor while satisfying the nuclear criticality condition.

Jan 1, 2000

By Sheng X. L

The Jurassic coals at Datong are characterised by their strong, massive sandstone and conglomerate roofs which fail suddenly over large areas, crushing pillars and creating destructive windblasts. collapsed areas have exceeded 180,000m2 and windblasts have extended over one km underground and 200m on the surface and have been accompanied by subsidence troughs on the surface. Scientific analysis has researched premonitory signs of caving and the nature of windblasts leading to considerations of alternative mining methods and ways of dissipating the energy of windblasts to reduce their damage and danger..

Jan 1, 1992

By S Farrokhpay, M Zanin

Although it is well understood that in flotation collection zone and froth zone are deeply interconnected, and reagents (and in particular collectors and frothers) cannot be selected without considering their synergistic effect, this concept is rarely applied in plant practice. The feed mineralogy also has an important role in how particles and reagents interact in flotation, which is sometimes overlooked by operators. In this work, a combination of batch flotation tests and froth stability measurements was used to optimise the collector and frother scheme for the flotation of a copper ore. The methodology was applied to an Australian copper plant which was experiencing high variability in froth stability in the roughers when the feed ore mineralogy was changing. It was hypothesised that chalcopyrite in the feed in combination with isobutyl-xanthate had a destabilising effect on the froth phase under the reagents scheme used. Froth stability was restored if a shorter chain length, less hydrophobic, xanthate was employed. It is apparent that the hydrophobicity of adsorbed films at the solid/liquid/air interfaces has a critical role in enhancing or reducing froth stability. Unstable froth causes a reduction in copper recovery in spite of a high collection zone flotation rate. The case study suggests that collection zone and froth zone can rarely be optimised independently of each other. With the laboratory procedure adopted, a more suitable reagents scheme was determined to respond to changes in the feed mineralogy, avoiding fluctuations in plant performance due to unexpected froth instability.CITATION:Farrokhpay, S and Zanin, M, 2012. Synergic effect of collector and frother on froth stability and flotation recovery - An industrial case, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 145-150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The working of alluvial deposits has from all times been a popular form of mining, not only from the simplieity of its operations, but also, in its more primitive stages, from the possibility of carrying it on without large capital, without skilled lahour, expensive plant, long terms of preparatory work, or, in fact, any other requisite than a shovel, a dish, and a stout pair of arms. It is possibly one of the oldest industries, and probably, also, it has been one of the most profitable.In tbe Australian States the happy days of rid alluvial deposits, when gold was to be hltd for the shovelling, are now almost over. The lust for gold has caused almost every corner of the world to be ransacked, and the more easily earned wealth to he exhausted: for the most part there remain now those deposits only which are too poor to be profitably worked by means of the implements and methods of old times. But, though the deposits have become poorer, the keen inventiveness of man has devised means whereby such large quantIties can be treated at a cost so low that he can still make a profit out of them. In this article, out of the many means devised, three only will be referred to-viz., hydraulic sluicing, bucket dredging, and hydraulic dredging. All mining may be divided into three principal operations-1st, the breaking down and conveying of the ground to where it is to be treated for the recovery of the metallic values, 2nd, the treatment of the material for the recovery of those values; and, 3rd) the removal of the worthless material or tailings. In all mining the object is to effect these three processes for the least expenditure of money commensurate with the highest degree of efficiency.

Jan 1, 1907

By Watsford RMS, Schache IS, Slaughter PJ

As part of the overall Copper Smelter expansion activities at Mount Isa Mines from 1970 - 1975, a decision was made to open circuit the converter slag from the Smelter and treat this product by flotation. This paper describes the technical aspects of plant operating and reagent practices employed, with particular emphasis on the large scale milling of this product and the effect through the use of reagent hydroxy ethyl cellulose on chalcocite grade and recovery.

Jan 1, 1978

By OÆBrien D, Priddle D

In order to avoid costly moisture penalties on coal shipments and to minimise rail freight costs, screen bowl centrifuges were selected and installed in the Mount Thorley Coal Preparation Plant for dewatering fine coal product. The Mount Thorley fine coal circuit consists of desliming the -0.5 mm (ww) fine coal in two stages of classifying cyclones prior to recovery by froth flotation. Provision has been made to bypass the flotation circuit with the classified flotation feed reporting directly to product and the centrifuge dewatering circuit has been designed to handle either flotation feed or flotation product. Major mechanical failures of the gearboxes and the ceramic tiling occurred early in the operation life of the machines which led to design changes being made to achieve satisfactory operation. This paper discusses the operating experience at Mount Thorley with respect to both mechanical and metallurgical performance of the screen bowl centrifuges since their installation in 1985.

Jan 1, 1989

Three main divisions of the. Proterozoic are recognised in the North- West of Western Australia. These are referred to, in order of decreasing age as the Mt. Bruce Supergroup, the Bresnahan Group and the Bangemall Group. The stratigraphy and distribution of each is described, their relative ages discussed and a brief geological history of the whole area is Presented.

Jan 1, 1964

In Australian collieries, solutions to the outburst problem must be implemented in a highly competitive environment which has a low tolerance on negative productivity effects. Solutions are only applicable if the overall viability of the operation remains sound. Minimum time must be spent on alleviation and control measures. This is favoured by simple geology, advanced warning and efficient alleviation and control procedures. Research requirements in support of this include 1. an improved means of predicting the nature and location of outburst zones ahead of the face and, 2. an improved means of measuring the effectiveness of gas drainage. For additional safety at the face, a means of continuously monitoring outburst proneness is required. In general, greater emphasis is required on improved instrumentation.

Jan 1, 1987

By Van Deventer J S J

The first step in the design of a process to treat a possible economic precious metal deposit should be an examination of the mineralogy of the ore. Using this and other initial tests, the extractive metallurgist can design a process to treat the ore. In the field of precious metal metallurgy, little emphasis is placed on the mineralogical information available to the metallurgist. The information is of far more use to the geologist and the mining engineer. Diagnostic leaching was designed to open up the field of mineralogical analysis to the metallurgist. When a mineralogist looks at the deportment of gold in an ore, he is usually looking for an element which is present in parts per million, so that errors in sampling are multiplied dramatically. Diagnostic leaching offers a cheap, simple, practical alternative. In order to determine with which minerals the desired precious metal is associated, a specific mineral is first eliminated using a selective oxidative leach, and cyanidation is used to extract the precious metal (in this case gold and silver) liberated by the destruction of this mineral. The precious metal extracted can be measured in solution to give a fairly accurate record of the amount of the precious metal associated with that mineral. Furthermore, the residue from this first stage can be subjected to another selective acid leach, and the process repeated. The procedure can be varied to suit the mineralogy of the matrix material. At the end of this diagnostic leach the metallurgist is left with a complete record of the deportment of the precious metal. He can now use this information to design a metallurgical flowsheet to treat the ore. Diagnostic leaching is thus an analytical tool which can be used by the metallurgist not only to examine new ores, but also to look at problems occurring at existing plants. The procedure is not only limited to ores and residues but in fact can deal with any type of intermediary product that occurs on a plant. The information gained from analysing an intermediary product can give a useful indication of how well a unit process is working, eg flotation, roasting, etc.

Jan 1, 1992

By Morland R

Recent influence of backfill stability on stope production in the Copper Mine at Mount Isa Mines Limited is described. Changes to the mining process to improve fill stability are described, including increased focus on fill performance, modifications to extraction techniques, increased fill quality, changes to drill and blast practice, and research into backfill stability. Several case studies are described.

Jan 1, 1995

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

The word governing derives from gubernare meaningto pilot a ship. Being inclined to metaphors, one could be forgiven to think that politicians act this verb and captain the Nation's ship into some definite course. In the case of at least the mineral resources industry, it seems that there are not many James Cook followers in our parliaments: Australia's approach to mineral and energy policy is often chaotic - witness the 1935 to 1961 ban on iron ore export-ing which prevented the development of a significant steel industry at time when the World was hungry for this metal, just to mention one amongst many other examples.The follies of Australia's mineral policies are well il-lustrated in the case of uranium mining. Although Australia had the Western World's largest economic reserves of uranium, it is onlythefifth producing nation and its uranium potential is largely unrealised. At the root of this situation are the interventionist attitudes and policies of successive Federal Governments which for more than four decades distorted the Investment decision and, in more recent times. discouraaed investment.

Jan 1, 1990

The difference between a hypothetical and a theoretical approach is considered and the advantages in using a hypothesis is discussed. Virgin horizontal stresses play an important role in stabilising strata which bridge across an excavation, and reduces the tensile stresses which develop in a beam subjected to bending. Simple formulae are deduced for the bridging of a thick massive stratum under such conditions. At shallow depths, tensile failure on the upper side of the beam is the most likely cause of fracture, but below a certain depth this gives place to compressive failure on the underside, with the possible incidence of rock bumps. The presence of strong massive beds delay the onset of subsidence and may restrict the width of the subsidence trough. If the material involved in the caving is strong, this will reduce the final subsidence, especially at shallow depths. The British regulations for the control of aquifers and their dependence on the strain developed at the seabed are discussed. As an alternative, the concept of a disturbance factor is introduced to permit the consider- ation of aquifers at depth, leading to an explanation of the make of water on the first faces to be mined in the Selby Coalfield. 'Elie paper closes with a brief consideration of the different roles played by longwall face supports in the control of readily cavable strata, and the control of strong beds which hold up in the waste.

Jan 1, 1986

A Devonian metallogenic province is extended northwards from central Queen- -sland to the Burdekin Basin in the Charters Towers Gold and Mineral Field. Devonian sediments of the Burdekin Basin are intruded by mineralised quartz felspar porphyry which occurs as pebbles in Upper Devonian conglomerate. A mineralised volcanic complex lies on the crest of an anticline in Devonian sediments.Red siltstone is slurried and reduced to pyritic hornfels over folded limestone.A thick wedge of volcanogenic conglomerate overlain by marine shale lies on the mineralised rim of an ocean which suffered cataclysmic changes during Late Devonian times.

Jan 1, 1987

Results are presented of the investigation of gas dynamics of the blast furnace process obtained on laboratory models and operating furnaces. Gas residence times were measured using a helium tracer technique developed for the purpose. Residence times were determined in furnaces of 1007 m3 and 1719 m3 and results used in the calculation of the burden parameters and to estimate the distribution of the gas flow along the furnace radius. The effect of tuyere injection of coal dust on gas distribution was also investigated and the advantage of continuous injection compared with intermittent injection is noted. The unevenness of gas distribution across the furnace area is found to correlate well with differences in the size analysis of the iron-bearing component of the burden. The mixing of the gas streams between the neighbouring raceways was studied. It is shown that in the central region of the furnace gases from every tuyere are mixed together, whilst in the peripheral regions mixing is more localised and includes only the sections consisting of five adjacent tuyeres. A solution is proposed to the problem of a theoretical evaluation of the critical gas velocity. A simple relationship between the Reynolds and the Archimedes numbers was obtained from which, after substitution of the burden size data and the gas parameters, it is -possible to evaluate the critical gas velocity. Conclusions include information relating to the optimisation of the gas distribution and views on reducing gas injection at elevated furnace levels.

Jan 1, 1975

By G Diprose

Diamond exploration in Queensland is influenced by the South African approach modified by the discovery of diamonds in Lamproite in Western Australia. The current approach is to explore for Kimberlite and Lamproite bodies using indicator minerals dispersed by fluvial and colluvial processes. In the north-west, diamonds are derived from kimberlitic and lamproitic sources, whereas those in the coastal and subcoastal areas of eastern Queensland are associated with xenoliths included in rocks formed during Cainozoic volcanism. In these areas, sapphire is commonly associated with diamonds. In New South Wales diamonds in economic quantities occur in alkali basaltic intrusions and a subduction model has been proposed for these occurrences (Barrows et al, 1996). Exploration for diamonds in Australia increased following the discovery and exploitation of the Argyle mine. State geological surveys have produced digital information on the local occurrences of diamonds. As part of the Smart Mining Initiative (2006 - 2010), the Geological Survey of Queensland compiled a database and report on microdiamonds and diamond indicator minerals from open file company exploration data from 1968 to 2008 from the Department of Mines and EnergyÆs QDEX system. Most exploration in Queensland was conducted with exploration for other commodities. There is no commercial exploitation of diamonds in Queensland and, to date, only rare occurrences of microdiamonds. There is a regional difference in diamond occurrences with the kimberlitic and lamproitic models favoured for the north-western regions of the State and the subduction (S-type model) favoured for the eastern coastal zone linked to Cainozoic alkalic basaltic volcanism. Further diamond exploration is warranted in Cainozoic basalt provinces along the eastern coastal and near coastal regions and in the north-west of the state in conjunction with airborne geophysics flown as part of current Departmental Smart initiatives. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008