Search Documents

By Swift D. G

For some time the Electricity Trust of South Australia (ETSA) has been investigating the application of new mining methods and equipment to minimise the cost impact of the steadily increasing depth of mining brought about by the 20¦ dip of the coal seams at the Leigh Creek Coalfield. Exhaustive examination of all suitable mining systems showed that highly mechanised systems involving belt conveyors displayed no eco- nomic or operational advantages over shovel and truck methods. However, the configuration of the Leigh Creek coalfield allows for two quite different approaches to mining by shovel and truck. The current strip mining method involves removing overburden from the highwall in 60 m to 200 m wide strips to progressively expose the coal down dip, and requires all waste to be hauled to the surface. The alternative ter- race haulback method involves opening a boxcut to full depth at one end of the coalfield, then mining the full section along strike and placing the spoil in the mined out area. On a strictly economic basis, the latter is clearly advantageous, but the former has significant less tangible advantages. In deciding between the two methods ETSA is faced with the need to examine the applicability of each method under a wide range of possible future demands on the coalfield, and to assess the importance of many intangible factors.

Jan 1, 1989

By B Menzel, M Wlasenko, J Phillips

Yandicoogina (Yandi) open pit mine is located in the eastern part of the Pilbara region of Western Australia. It hosts pisolitic iron-oxide mineralisation distributed within a meandering paleoriver channel. The deposit is characterised by clays occurring as lenses, accretions, desiccation joint infill and voids in the pisolite ore. The irregular shapes and highly erratic distribution of these clay pods represent a serious challenge for grade control at this mine.The current grade control approach used at the Yandi mine is based on sampling of production blastholes on a 6 m X 6 m spacing. Their good spatial coverage, tight spacing and low cost make blastholes a very convenient media for grade control and ore-waste definition. However the potential downside of this grade control approach is poor sample representivity. An alternative grade control approach is to drill and sample using reverse circulation (RC) holes distributed on a 25 m X 25 m grid. This approach has been tested in Yandi mine and compared with the blasthole sampling approach for sample representivity. The impact of increased drill spacing on mining block predictions has been studied using a conditional simulation technique. Blasthole and RC samples proved to be similarly biased, underestimating Al2O3 and SiO2 grades and overestimating Fe grades, when compared to full cone assays. These results show that using RC drilling for grade control at the Yandi open pit will not necessarily improve the representivity of the grade control samples. However, increasing the grade control spacing to 25 m X 25 m will lead to more than 12 per cent of the selective mining unit (SMU) sized blocks being misclassified. This is approximately a two-fold increase in the number of misclassified SMU blocks in comparison with 5 m X 5 m spacing.

Jan 1, 2007

The Geograph is a revolutionary seismic system involving special techniques in combining the use of FIT magnetic tape with shock wave echoes created by a weight dropping system.The idea of- weight dropping as a- source of seismic energy is not a new,.,oxie. Records 'indicate òa pos'sihle use of falling weights as early as .1929. 'Dr. Burton McCollum began his experiments in 1938, but it wasn't until 1951 that the method was first proven useful.The first weight dropping crew began commercial operations in Edwards and Sutton .Counties of West Texas in 1953. By 1962, more than '40 weight drop-ping.crews have come into existence with operations in the United States, Canada, Algeria, Iraq, Argent na,òSpanish West Africa, Tunisia, Qatar, Niger Morocco and Libya by most major oil companies and larger independent oil companies. .

Jan 1, 1962

By Mowat BA, Leach TM

The Morobe Goldfield in Papua New Guinea has produced in excess of 120 tonnes of gold from predominantly alluvial sources. Hardrock gold has been mined historically at Wau (23t) and Edie Creek (40 and geological resources have been established at Hidden Valley (780, Kerimenge (360 and Hamata (30t). Numerous prospects have also been identified within the goldfield. Primary gold mineralisation is related to intrusion of dacitic to andesitic Edie Porphyry (2.4 to 3.8 Ma), often with associated diatremes, which have intruded along major regional structures. A full spectrum of deposit styles from proximal (mesothermal) to distal (epithermal) to the porphyry source is recognised. The transition between the proximal and distal styles is recognised both between deposits and within an individual deposit. The deposit styles should be termed porphyry related gold mineralisation rather than given the generic epithermal and mesothermal labels.

Jan 1, 1995

Relationships between lead blast furnace performance and the composition and size distribution of sinter were determined from analysis of lead blast furnace operating data. Sintering plant practice was subsequently modified and substantially improved furnace performance resulted.

Jan 1, 1971

Following the Moura No 2 Wardens Court of Inquiry and subsequent changes to the Queensland Mining Legislation there is a requirement in Queensland coal mines for: a person with the recognised competencies to be appointed at each underground coal mine to the position Ventilation Officer; and the person is directly responsible for the implementation of the mine ventilation system and for the establishment of effective standards of ventilation for the mine. The Regulations require that an underground mine must have principal hazard management plans that provide for at the least the following: emergency response, gas management, methane drainage, mine ventilation, spontaneous combustion, and strata control. Other than strata control all the plans require the ventilation officer to have roles and responsibilities to develop, control, monitor and undertake actions in relation to these plans.There are also another 34 Regulations that either directly or indirectly requires the Ventilation Officer to take actions.The purpose of this paper is to outline the information that the regulators look for in sealing plans and the actions the regulators will take if the sealing does not go to plan (TARPs being exceeded).

Jan 1, 2005

By Standish N

The heterogeneous reactions of carbonaceous materials with oxidising gases are basic to all combustion phenomena and to many gasification processes. The carbon- carbon dioxide reaction at elevated temperatures (Reactivity) plays important roles in many metallurgical operations like iron blast furnace and ferro-alloys smeltings, zinc and lead smelting, alumina reduction, cupola operation and direct reduction processes. The stoichiometry but not the mechanism of the reaction between CO2 and carbon is represented by the equation (Boudouard reaction) CO2 + C 2CO (1) This reaction is more complex than that between carbon monoxide and metal oxides, which involves essentially a transfer of oxygen from the oxide to carbon monoxide to generate carbon dioxide without any change in gas volume, whereas the volume of the product gas of Equation (1) is twice that of the reactant gas. In the present paper an attempt has been made to review critically the reactivity measurements of various carbonaceous materials in carbon dioxide atmosphere. Steps in C-CO2 reactions, surface reaction mechanism, role of mass transfer on reaction kinetics, dynamic oxygen exchange reaction and rate equations and rate controlling steps are discussed. Various methods of reactivity measurements with their pros and cons are also presented. Effects of pertinent process variables on the reactivity of carbon are also described in detail.

Jan 1, 1986

By Restarick CJ

Plant data are presented which indicate a relationship between flotation rate constants and pulp density in zinc cleaning circuits at Broken Hill. The data were obtained from down the bank sampling of cleaner and recleaner banks at North Broken Hill and New Broken Hill Consolidated Concentrators. It was found that, under normal plant operation, flotation rate constants increased at the lower pulp densities existing in the later cells of cleaner banks. The addition of dilution water to the feed to the bank increased flotation rate constants, thereby confirming the relationship. It is shown that the relationship between flotation rate constant and pulp density is size dependent, being most pronounced for larger sized particles. In contrast, the effect is not markedly dependent upon mineral type. Possible consequences of this relationship for control of cleaner operation are discussed with the aid of some simulated results.

Jan 1, 1978

By Hanley J

Coal winning in the Latrobe Valley exceeds 45 mtpa uses a small number of Bucket Wheel Excavators and high speed conveyor systems. While this equipment offers many advantages in the production cycle, incorrect use can lead to low productivity and risks to the safety of the operators and equipment. The mining equipment is of high capital value and easily damaged when used outside the correct operating range. In the extreme case, this can result in total machine collapse, having major implications for personnel safety as well as production and costs. With an active productivity improvement program in the Latrobe Valley in the last two years resulting in a 50 per cent reduction of personnel, many experienced operators have retired. Mine management are facing the urgent need to rapidly train new operators to maintain high productivity levels and reduce the risk of accidents to personnel and high capital cost plant. With the assistance of the Central Gippsland College of TAFE a Certificate Level course has been developed for open cut operators. The course covers all essential training needs for the Latrobe Valley mines. The training is developed from National Competency Standards, allowing transfer of skills, and is flexible to suit other enterprises. It has been written for self-paced learning with the total job understanding, and to have competency-based learning outcomes, training tasks and assessments built-in to modules. With the introduction of this new training program, management is convinced that the element of risk within the mine will be significantly reduced. For these reasons it is an ideal training model for other enterprises.

Jan 1, 1994

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

By A Califice, E Pirard, M Benzaazoua, R Mermillod-Blondin

Image analysis is more and more considered as a powerful tool for quantitative analysis of ores and concentrates. Apart from being very much dependent upon the quality of the imaging principle and the adequacy of the imaging sensor, quantitative image analysis is also the result of a long chain of material, image and pixel sampling strategies. The most reliable way to demonstrate the accuracy and the precision of modal analysis obtained from images is probably to use a blended material with known proportions of pure minerals and confront the results obtained from different analytical tools. This operation has been performed on a series of mineral blends mimicking the tailings of a flotation operation in a plant operating on massive sulfide mineralisation. The intention was to be able to better predict acid mine drainage potential from direct mineralogical observations. Selected sulfide minerals: pyrite (Py), pyrrhotite (Po), chalcopyrite (Cp) and sphalerite (Sp) were mixed as variable amounts within gangue minerals (quartz, calcite, dolomite and siderite). Typical blends contained six to ten per cent (Py); one to three per cent (Po); 0.5 to one per cent (Cp, Sp); 15 to 40 per cent carbonates and 40 to 75 per cent quartz by mass. The 1000 gram blends were carefully sampled and prepared for X-ray diffraction, chemical analysis by ICP-AES and optical microscopy image analysis (OMIA). Results obtained for the different analytical techniques are compared and discussed revealing the limits and strength of each method in the accurate quantification of sulfide and gangue minerals.

Jan 1, 2008

By J Rowland, B Belle, M Webber

The Australian underground coal industry has experienced substantial improvements in longwall productivity and, as such, the methods of providing a safe and productive mine environment have needed to evolve and develop. Whilst the primary method of controlling atmospheric conditions is by airflow it has become impracticable or impossible for the majority of Australian longwall mines to contend with all environmental hazards with primary ventilation alone.If the ventilation circuit cannot provide a safe and productive mine environment at an acceptable cost and circuit duty then supplementary controls are required. Examples include pre-gas drainage, post-gas drainage, gas utilisation, refrigeration and innovative dust control systems. Of the 21 longwall operations surveyed in Australia, there were 13 in New South Wales and eight in Queensland.This study represents a timely opportunity for the industry to examine the primary and supplementary ventilation systems implemented in Australian longwall mines and to discuss how to equip the industry to successfully face the future of underground longwall ventilation management in Australia.CITATION:Webber, M, Belle, B and Rowland, J, 2017. Australian longwall ventilation systems, in Proceedings Australian Mine Vent Conference 2017, pp 301–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Yao S, Wang P, Zhang C

The Zhilingtou Au-Ag deposit is situated in the eastern part of the complexly deformed and metamorphosed South China Caledonian Fold Belt. It consists of seven orebodies that are almost exclusively hosted by biotite plagioclase gneiss of the Precambrian Chencai Group. They form an apparent en echelon pattern in both cross-section and level plan. Three different ore types, based on mineralization textures, have been recognized within the Zhilingtou lode. These are Au-Ag-rich quartz veins, Au and Ag-bearing silicified rocks and Au-Ag-containing altered rocks with quartz stockworks. The mineralization is principally composed of electrum, argentite, pyrite and minor sphalerite, galena as well as traces of hessite and chalcopyrite plus a gangue assemblage of quartz, rhodonite, sericite and chlorite. Fluid inclusions related to Au-Ag mineralization yield a wide range of homogenization temperatures from 110 to 447¦C, with two distinctive peak values at 250-300¦C and 350-400¦C respectively. S30Si values of quartz veins and silicification from the three stages of mineralization range from -0.1 to -0.4%o. The mineralization at Zhilingtou is interpreted as forming by recirculated meteoric water extracting ore-forming elements from metamorphic rocks due to Mesozoic volcano-magmatic activity.

Jan 1, 1995

By C L Humphrey

Biological monitoring programs for environmental protection require techniques that will provide both early detection of possible adverse effects, and assessment of the ecological significance of these effects. Monitoring techniques must include responses sensitive to the impact, that can be subjected to rigorous statistical analysis and for which statistical power is high. Such issues in baseline research of 'what and how to measure?' and 'for how long?' have been the focus of a program being developed to monitor and assess effects of mining operations on the effectively pristine, freshwater ecosystems of the Alligator Rivers Region (ARR) in tropical northern Australia. Application of the BACIP design, utilising a form of temporal replication, to univariate data (single species) and multivariate (community) data is described. For new ventures in Australia (such as mining), monitoring programs should be designed to establish with high probability that an impact on the ecosystem no greater than a prescribed amount has gone undetected - as opposed to simply allowing development to continue as long as 'proof' of impact is not available. Such a precautionary approach represents a shifting of the 'burden of proof' and would require with the BACIP design, a minimum number of baseline years in order to achieve some desired level of statistical power in a test for impact. Power analyses conducted on two to five years (depending upon the technique) of baseline data from streams of the ARR indicate that the BACIP design would not impose developmental constraints on mining and that a policy of reversal of the burden of proof would provide the cornerstone required for managing such development in an ecologically sustainable manner.

Jan 1, 1994

By J-P Franzidis, E V. Manl, K Runge

Over recent years a number of techniques have been developed as part of the Australian Minerals Industries Research Association (AMIRA) P9 project to represent mathematically or measure directly subprocesses occurring in flotation cells. These include the determination of a:machine parameter (bubble surface area flux, Sb); froth parameter (froth recovery, Rf); entrainment and drainage parameters; and ore floatability parameter (Pi). A cost-effective methodology was developed for using these techniques to derive models of flotation circuits. This methodology was applied to derive a model of the flotation circuit at the Western Mining Corporation (WMC) Ltd Mt Keith Nickel Concentrator. The model was used to simulate a number of minor circuit flowsheet changes, the results of which are discussed in this paper. One year later, a second study of this plant was conducted. In this second study, data were collected while operating the plant in the flowsheet configurations that were simulated from the model developed from the first study. The results obtained from the second study showed reasonable agreement with the trends predicted from the first study model; discrepancies can be explained in terms of the model assumptions. This suggests that this simple circuit modelling methodology can be useful in assisting plant engineers to optimise flotation circuits.

Jan 1, 2000

By Collier D

The topaz resource at Torrington in northern N.S.W is currently the subject of a joint research and development programme managed by Pacific Copper Ltd, This programme has culminated in a pilot topaz calcination plant, located at Parramatta, which, through its operation, will establish the commercial viability of developing this mineral as an industrial raw material for both the refractory and fluoride chemical industries.

Jan 1, 1989

By Kelly E. G

New Zealand suffers the disadvantage of widely scattered ore bodies, none of which is large enough to economically support its own smelter. This leads to the concept of a centrally located smelter which must be flexible enough to cope with var

Jan 1, 1980

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is anenergy efficient way of grinding and a number of operations haveutilised this in the design of their comminution circuits. Owing tothe large flow of slurry through the mill that results fromoperating this way the grates and pulp lifters have to be designedto cope. However, the literature has little or no information onhow grate and pulp lifter size and design are related to theirability to remove slurry from the mill. Over the last few years theJKMRC has been researching this area and has developedrelationships between grate/pulp lifter design and flowratecapacity. At the same time it has determined the major causes ofpulp lifter inefficiency and a solution to preventing thisinefficiency (the Twin Chamber Pulp Lifter). This paperdescribes the models that have been developed through thisprogram and uses industrial scale data to illustrate their accuracy.Results from the industrial trials of the Twin Chamber PulpLifter are also presented.

Jan 1, 2001

By Will D. P

A 328 m, 2.4 m diameter raise-bored shaft has been equipped with a modular ladderway system to provide a second means of egress from Aberfoyle's Hellyer Mine in Tasmania. The modular ladderway consists of platforms, ladders and service pipes assembled at the surface and progressively lowered down the shaft. This system provides a rapid, safe and economical non-entry approach to equipping a shaft. The modular construction and single suspension allows for future extension or for reuse in another shaft.

Jan 1, 1988

Various factors influence the exploration geologist or geochemist in his choice of.an analytical method for gold and other elements which may help him find the elusive gold deposit. One of the first decisions the geologist must make is the nature of sample media to collect for his survey. Needless to say there are many media available depending on the situation. These include rocks, soils, heavy mineral concentrates (from overburden drilling and panned concentrates), humus, vegetation, water, lake bottom sediments, stream sediments, etc. The choice of the sample media will depend to a large degree on the state of development of the particular project from grassroots to mine feasibility. The nature of the geological information required will affect which media and which analytical technique should be chosen for the analysis. Valid sampling from the initial sample collection, preparation and subsampling aspects may also help to determine which analytical procedure is best. Cost and turnaround time are of prime. importance to the explorationist, as it should be, however, these aspects should not be detached from receiving accurate and reliable results.

Jan 1, 1987