Search Documents

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

By P F. Knights

Mining companies are striving to achieve new levels of operational maturity and drive process improvement across the organisation in the face of unprecedented demand and limited supply of experienced human resources. Advanced analytics techniques can help overcome these fundamental challenges by applying data techniques not previously applied in mining. Today, decisions are usually locally optimised but do not achieve optimum capability for the value chain. Although more information is collected then ever before, it is difficult to link many sources of data together in the same place in real-time, for example plant history, maintenance, mine planning, logistics and engineering data. Consequently complex analysis of data is time consuming and requires specialist skills and knowledge, and is often neglected in the decision-making process. In the future, analytics will close the loop between analysing data and taking action. Analytics will become embedded in the business and routinely applied to improve decision making across the organisation, from senior management to operations and maintenance workers, but will not require specialist skills or be time consuming to analyse data. As analytics becomes embedded in the business process, decisions are supported by data (not on gut feel), and critically, data from many sources are integrated in real-time to improve the quality of decisions. Ultimately, predictive tools will help suggest, or even in some cases automate, courses of action. The main opportunities for analytics exist where the enterprise requires supporting technology to enable it to continue to evolve to higher level of maturity. This will be in the areas of asset management, rapid reconciliation and adaptive planning, and the inbound and outbound supply chains. Advanced analytics are also a key enabler for increasing the effectiveness and realising the true value of Remote Operations Centres to safely and efficiently support operations in remote locations with smaller workforces.

Jan 1, 2008

Over the last five years Du Pont (Australia) Ltd has developed a commercial range of new generation emulsion based explosives concurrently with the development of new explosives-placement systems. The paper outlines Du Pont's emulsion technology and history of product development from the initial emulsions (Tovex E & EL) to emulsion/ANFO blends (Tovex BE) through to the most recent development of Du Pont's SOL emulsion component. The paper also outlines the development of materials handling systems on site to load waterproof bulk explosives from the original pumper trucks through to the multipurpose agitator bowl blending and pumping units at the heart of Du Pont's SOL emulsion system currently available within Australia. The last section deals with some of the more important features of enhanced agitator bowl truck designs and outlines examples of the complete SOL emulsion system and methods of operations currently practiced at specific mines within the Bowen Basin coalfields.

Jan 1, 1986

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

By Pyrih R, House A, Shangraw J, Silva AJ

Sunbeam Mining -Corporation has the inten mine with heap leach gold recovery, near spent ore indicated a relatively high ar topographical configuration, the spent across a small drainage and a lake. Du permit for spent ore disposal from th agencies, concerns about the potential contamination by the arsenic were expres conducted extensive studies to addre contamination. These studies consiste( geochemical and geotechnical parameters underlying the proposed disposal si geotechnical investigations were also hydrologic characteristics were include with the use of an IBM PC computer. :ion of opening an open pit gold Stanley, Idaho. Testing of the ?enic content. Due to the local ore was planned to be disposed :ing the process of obtaining a federal and state regulatory for surface and ground water .ed. Sunbeam Mining Corporation is the potential for arsenic of laboratory testing of both of the spent ore, and the soils te. Field hydrogeologic and -onducted. Local climatic and 1 in the analysis of these data Conclusions of studies indicated that although the seepage through the spent ore disposal would contain an elevated dissolved arsenic content, the hydrologic and geochemical characteristics of the site would prevent arsenic migration into the local ground water system. The attenuation of arsenic on soils with high clay content, and dilution after reaching the ground water table would lower the arsenic content to acceptable Concentrations.

Jan 1, 1988

Over the past 15 years, Artificial Intelligence (AI) techniques have shown promise of providing the ability to capture `human intelligence' into a computer program. The sub-fields of Expert Systems and Artificial Neural Networks are finding increased use in industry to perform tasks previously considered the domain of human thinking. But, are these methods just a new type of software much like that of the past or is real magic hidden within the lines of code? Will this field continue to enjoy high growth rates and if so, what developments will we see in the near future? Which algorithms and methodologies will continue to grow? This paper discusses a number of paradigms which can be used to create successful applications. There are certain barriers; some psychological - some linked with knowledge acquisition, that must be overcome or avoided to ensure system performance. Development time also requires careful consideration before embarking on an Al project. The paper focusses on constructing goal-driven systems that transfer high-technology solutions from the research laboratory to the plant floor. Respect for system users is of paramount importance - whether their involvement is to access contained information or to participate in program maintenance as new knowledge becomes available. Examples of successful and unsuccessful AI implementation in Canadian industry and academia provide evidence of the importance of this issue. The paper also examines some current constraints on applying AI in the real-world. Among these problems are automated knowledge acquisition, methods to acquire data during run-time, real-time systems (hardware versus software), explanation and justification features and adaptive/leaning systems.

Jan 1, 1995

By A S. Bamber

Mining is the oldest industrial practice on the planet with a history dating back over 3000 years. Since the early iron age ores have been extracted for use in a variety of contexts by humankind, from domestic to military, transport and more recently for complex industrial applications. Mineral exploration and extraction has evolved from the early exploitation of primary metal occurrences in relatively small quantities such as iron, gold, coal and copper, to the bulk mining and extraction of highly complex polymetallic oxides and sulfides today. Since the industrial revolution, mining practice has evolved substantially to support an increasing range and quantity of required metals and to accommodate the increasing scarcity of high-quality sources of these metals. A common response to the increasing scarcity of mineral resources has been to expand production through simple economies of scale, thus diluting fixed costs. This approach, however, is increasingly ineffective in the face of current trends, that include increasingly complex mineralogy, increasing pressure on environmental footprint - energy in particular, and increasing scarcity of capital for the construction of presently popular æmega-minesÆ. This paper examines historical trends and current practice in mineral exploitation in the light of the current global revolution in social, environmental and economic values as the projects move towards a vastly different topology for the industry for continued success in years to come.CITATION:Bamber, A S, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Bowden MW

Sintering of lead-zinc concentrates is practised by Sulphide Corporation to provide both desulfurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulfur dioxide gas for sulfuric acid manufacture.Moisture control of feed mixes is of paramount importance in the sintering operation and improvements in this area have realised increases in overall plant performance.

Jan 1, 1985

By Nag D. K

The Dolphin Scheelite orebody is located near the old mining town of Grassy on the south-east comer of King Island in Tasmania. Surface open cut mining of the Dolphin deposit was conducted for a number of years, then the proximity of the sea and adverse stipping ratio led to underground mining. As a result of the variable orientation and dimensions of parts of the orebody a number of mining methods were practiced at the Dolphin mine until 1990 when a combination of high processing and surface site costs coupled with low tungsten prices led to the cessation of operations. In this paper the different mining methods practised are examined and critically reviewed. The more successful mining methods were developed with experience and improving equipment technology to the extent that the underground operation produced ore at the lowest unit cost during the final years of operation.

Jan 1, 1995

By Thomas R. J

Following asmallnumberofpollutionincidents involving the death of cattle from ingestion of cyanide that had escaped from gold processing plants, the Queensland Government undertook to develop competent guidelines addressing this problem. These guidelines, "Queensland Government Guidelines on Prevention of Water Pollution from Cyanide Use in Gold Ore Processing", issued by the Department of Environment and Heritage, Department of Resource Industries and Water Resources Commission, cover hydrology and general house-keeping intended to reduce the likelihood of significant impact from a spill or unintentional dis- charge of contaminated material. There are three major advances for Queensland embodied in this Guideline: ò the use of a design approach that gives site specific standards rather than trying to give a multitude of standards broad enough to cover all situations, ò the use of hazard assessment and a "critical period" hydrologi- cal design technique, and ò new monitoring and reporting requirements. The guideline is presented here in a summary form:

Jan 1, 1991

The progress of longhole open stoping (LHOS) at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) is described. The design of a novel sloped wall longhole stoping method at NBHC which should allow the cuplete extraction of the orebody without the formation of pillars and with minimal dilution of the ore with sandfill is reviewed.

Jan 1, 1983

The philosophy of computer control of grinding and flotation at ZC/NBHC is presented. The performance and reliability of the in- stalled systems are discussed.

Jan 1, 1978

By Tukkimies M

During the late-1980s crawler-mounted crusher units established their position in the aggregates industry. Between 1986 and 1994 about 700 units were delivered to customers all over the world for surface operations, mainly in Scandinavia and central Europe. The crawler-mounted units are popular among smaller crushing operators because they are versatile and easy to move between sites. In large quarries the greatest benefit is obtained by combining a primary crawler-mounted crusher unit with mobile belt conveyors which eliminates the need for costly haulage by dump truck. Savings of up to 40 per cent in production costs prior to secondary crushing have been achieved. Today the environmental aspect in quarrying is assuming ever greater importance. Besides being costly the dump trucks are also the major source of dust and exhaust fumes within a quarry. A complete face crushing system consisting of a crawler-mounted crusher unit and mobile belt conveyors can be electrically driven and can be equipped with dust encapsulation and dust collectors. A mobile crushing unit is not a new idea. From the mid-1950s onwards the mobile and self-propelled units have been built equipped with crawlers, tyres or walking mechanisms, with weights usually of 500-1000 t. Due to their massive size these unit are not mobile in the same way as the today's mobile units. It is not feasible to move them more than a few times a year unlike today's fully mobile units which are often relocated once an hour. This means that the massive units can not continuously follow the production face and their loading always requires a certain amount of haulage. Today the mining industry is facing new challenges. With low mineral prices and high labour costs, increasing productivity is essential for survival. New standards are also being set for the labour safety and the environment. Large research programs have been launched to meet these challenges. However, technology which can partly solve these problems already exist and is only waiting to be introduced into underground applications as well - the mobile crushing unit followed by belt conveying. As in surface operations the elimination of truck haulage also brings considerable savings in operating costs in underground mines and reduces the amount of dust and exhaust gases generated. An additional benefit especially in underground applications is improved safety. In an underground mine most accidents are caused by moving vehicles.

Jan 1, 1995

By Agrawal R. D, Kapoor M. L

Activity of FeO in the ternary system MgO-FeO-CaO in contact with metallic iron has been measured at 1000 K employing the cell.PtIFe, (Mg, Fe, Ca)OIZr02 - CaOIFe, FeOlPt. Measured data are used to study the phase stability relations in the system MgO-FeO-CaO and an isothermal section at 1000 K through this system is drawn.

Jan 1, 1987

The mining production rate of two million tonnes per annum at Olympic Dam required greater servicing capacity than was available with the existing Whenan Shaft. To increase servicing capability a Service Decline was constructed from June 1986 to June 1987 extending 2000 m from the surface and linking up with inclining development from the existing Whenan Shaft workings. The decline was used for access of all men and materials during the construction phase of the ore handling system. During production, most mine servicing will be via the decline with hoisting of rock through Whenan Shaft.

Jan 1, 1988

By R R. J McAllister, K Moffat, S Heyenga

This paper examines the statistical relationship between quality of life indicators and the gross value of mineral production from Australian regions. We used quality of life indicators, aggregated for 673 local government areas, of household income, housing affordability, access to communication services, educational attainment, life expectancy and unemployment. We find no evidence of systematic negative associations between quality of life and the gross value of minerals production. Instead, mining activity has a positive impact on incomes, housing affordability and communication access across regional and remote Australia. Whilst we do not establish causality between mining activity and quality of life, our analysis prompts a rethink of the æresource curseÆ as it applies within a single country. Nevertheless, our findings are tempered by extensive anecdotal and empirical evidence of the negative social impacts of mining on specific demographic sectors, localities, families of fly-in, fly-out mining operations and individuals. This contrast may be a scale issue, with the regional benefits of mineral wealth masking highly-localised inequalities and disadvantage. We suggest that there is a need to better understand these impacts and, more importantly, the types of policy mechanisms government and industry can adopt to mitigate or avoid them.

Jan 1, 2009

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

Although the diesel engine is normally considered a tried and proven power source, many new and exciting diesel design concepts are being evaluated in engine development laboratories around the world. Three such programs currently underway at Cummins Engine Company are discussed. The turbocompound engine converts into power exhaust heat energy which is normally wasted. It does this by incorporating after the turbocharger a low pressure gas turbine which is gear driven to the crankshaft. The adiabatic engine has no conventional cooling system. It converts into useful power most of the heat energy normally rejected to the coolant. The series boost turbocharged engine uses seperate low and high pressure turbochargers to increase engine output and improve transient performance. These design concepts make possible increases in diesel engine thermal efficiency from the current 33 to 38 per cent range to the 50 percent range.

Jan 1, 1982

By M J. Nugus, S C. Dominy

Mesothermal lode-gold deposits often pose problems during sampling because of their complex and erratic gold grade distribution, and the presence of coarse gold. Effective sampling and sample preparation protocols must form the basis of any resource estimate at whatever stage a project is at. Design of a sampling regime must be based upon a thorough understanding of orebody mineralogy and geology. This should include consideration of gold particle size and distribution. The sample type, size and density employed must also be based on the underlying geology of the deposit. Choice of sample preparation procedure and assay type is of critical importance if fundamental sampling error and analytical errors are to be minimised. Traditional fire assays, using small charge sizes, consistently understate assays gained from large charge sizes and techniques such as screen fire assay and bulk leach extractable gold assay. The proportion of coarse gold within samples will have a profound effect on the requirements for sample preparation and assay method. The application of Gy sampling theory can help to reduce errors within the processing of samples of broken rock. Quality control/assurance of sampling regimes must also be critically assessed. The problems associated with sampling mesothermal lode-gold type deposits are presented as case studies from Western Australia and North America.

Jan 1, 2003

This paper outlines the aims, objectives and means by which a life of mine land use plan was established for Comalco's bauxite mine at Weipa. Comalco realises the need to strategically plan for future mining activities and still minimise the impact of operations on the natural resources of the region. With this realisation long-term forward planning has been implemented to improve the Company's ability to select future sites for mining, industrial use, agriculture, town expansion and conservation purposes.The knowledge of mineral, water, soil and animal resources has expanded dramatically in the past decade. During 1990 Cornalco purchased Geographic Information System technology which has allowed previously collected resource data to be presented in map form. These maps as part of the Life of Mine Land Use Plan are both information based and strategic which can be efficiently updated. The maps allow a broad audience from engineers, geologists, environmental scientists and site managers to government officers and the general public to comprehensively view and scrutinise the operations.

Jan 1, 1992