Search Documents

By Nash B. G W

In June 1976 a 600'tonne/day manganese ore sinter machine, with on-strand cooling, was commissioned at the plant of Tasmanian Electro Metallurgical Company Pty. Ltd. at Bell Bay, Tasmania. This machine was installed in order to utilize manganese lump ore screenings generated in the preparation of raw materials prior to charging to the electric smelting furnaces at Bell Bay. Since commissioning, trial sintering of a number of different grades of manganese ore fines from Groote Eylandt Mining Company Pty. Ltd, has been conducted and suitable sinter has been produced from these different grades. The sinter produced is used as part of the furnace burden in both ferro manganese production and silico manganese production. The inclusion of sinter as part of the charge in the production of ferro manganese has considerably improved furnace operating conditions and performance.

Jan 1, 1977

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By Sinha DK

Coal Mining in India had been confined in the past primarily to two or three coalfields. Unscientific mining has led to huge degradation of land including massive subsidence of strata and disturbances of water tables to a wide extent. This has caused problems not only in flooding of mines from surface water but also in further planning of the surface drainage for current mining activities. Now, therefore, surface hydrology and land-use potentialities of the area have been endangered inflicting severe damage to the overall environment and ecology of the area. The paper Discusses certain investigative aspects of the problems highlighted as above in one of the coalfields, and encompasses mainly the following areas : 1) Quantitative estimation of the damage already done to the natural surface drainage system. For this purpose damage to topography and drainage for the last fifty years have been made out through the aerial photographs and topographic map sheets 2) Analysis and comparison of different states of such photographs are carried through to indicate the extent of damage to the hydrological conditions inducing undesirable changes in its land-use pattern. Based on the analysis, concrete suggestions are made to restore the water drainage system which will be most suitable for future mining in the area containing high grade coal. The design and planning of the drainage system is based on the total system approach including the cost benefit analysis as well as hydrological considerations.

Jan 1, 1988

By Hall C. E, Chrisholm J. M

Resource calculations for shear hosted deposits of any type are difficult regardless of which calculation technique is used. One of the main problems is the determination of the geometry of the mineralisation. Once this has been elucidated then the appropriate resource calculation methodology can be employed with a search distance and orientation that is relevant.

Jan 1, 1993

By Rieniets S, Somerville J. L

In Morwell Open Cut brown coal mine, the overburden 'firehole' materials which have resulted from ancient coal fires vary-from hard baked clays to firm laminated lacustrine clays. The need to pre-strip designated areas to reduce the slope height and attain safe digging conditions for the bucket wheel excavator operation is now accepted practice at the open cut mine. In this study, the inherent spatial variability of undrained shear strength of the clay materials has been incorporated in a visco plastic, finite element based, probabilistic slope stability analysis. Data on the costs of initial pre-stripping, excavation and slope failure are collected to provide an economic basis for the optimisation of the design of the overburden batters in Morwell Open Cut. This improved stability modelling is enabling costly pre-stripping to be minimised while ensuring acceptable slope stability conditions and minimising the risk to personnel and plant.

Jan 1, 1994

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

By R D ROSENTHAL

BHP Iron Ore Ltd's Mt Whaleback is the largest single open-pit iron ore mine in the Pilbara region of Northwestern Western Australia. A division of BHP Minerals, one of three core businesses of Broken Hill Proprietary Company Ltd (BHP), BHP Iron Ore - Newman is a joint venture with minor participants C Itoh Minerals and Mitsui. Mine planning for Mt Whaleback generates detailed sequence plans for a long term forecast incorporating equipment requirements, marketing forecasts, and pit development strategy. Utilisation of several computer packages, both commercially available and site modified, are necessary to achieve such a demanding task.

Jan 1, 1992

A number of gases, such as carbon dioxide, methane, water vapour, nitrous oxide, ozone and chlorofluorocarbons are transparent to incoming short-wave radiation, but are relatively opaque to outgoing longwave radiation. Variations in the concentration of these gases in the troposphere can alter the thermal balance of the earth's atmosphere. Outgoing terrestrial radiation which would otherwise escape to space, is trapped within the inner layer of the atmosphere, resulting in a greenhouse effect. It is estimated that at present greenhouse gases other than carbon dioxide, contribute about 50% to the greenhouse effect. However, in the future, the contribution made to the greenhouse effect by gases other than C02 will become increasingly more significant. Greenhouse gases arise from a wide range of sources and their escalating increease is largely related to an increase in the world's population, an increase in the standard of living of many areas and changes in lifestyle. The effect of increasing man-made greenhouse gases in the troposphere is unknown but it is proposed that it may increase temperature and may modify climate, agricultural response and land use. The sources of greenhouse gases are identified and found to comprise a wide range of activities. The contribution that coals use makes to the greenhouse effect is examined in detail. It is concluded that coals total contribution is small being about 10% of man made greenhouse gases. Envisaged expansion of coal's use will only cause a small increase in greenhouse gas emissions. Whilst developing technology for coal's use for power generation has the potential to reduce greenhouse gas emissions from new plants by approximately 25%.

Jan 1, 1989

A major problem in the continuous casting of aluminium killed strip steel is the incidence of black and grey lines in the strip surface caused by the alumina inclusions. One place for limiting the number of alumina inclusions is by providing favourable fluid flow conditions in the ladle so that the inclusions float out to the surface or adhere to the ladle wall. In laboratory equipment 20 kg of steel was melted in an alumina crucible of 14 cm diameter in an induction furnace. Deoxidation was carried out while the melt was constantly stirred by argon bubbling. Bubble frequencies were measured at the lance tip using a microphone technique. High speed cine photo- graphy was incorporated to measure melt top surface velocities. Experimental results indicate that the rate of removal of inclusions is a function of both the gas input and the power input. However due to unfavourable surface area to volume ratio, reoxidation of the melt took place. Some other experimental difficulties in working at high temperatures are also discussed such as lance design, melting arrangement and sampling techniques.

Jan 1, 1984

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By Butters S. E, Deslandes J. V

The selection of loading and haulage equipment in a proposed or oper- ating mine is vital in ensuring the cost effective achievement of produc- tion targets. To assist in the evaluation of different haulage systems, a truck haulage simulation model has been developed at BHP Melbourne Research Laboratories. The operation of the model is described and exam- ples of an actual application at Mt. Whaleback Mine is presented.

Jan 1, 1989

By C Pypno, P Nowakowski, T Opasiak, C

Belt conveyors are machines for continuous transport with most applications in mining industry in Poland. This is a result of simple construction and cheap operating costs. But conveying materials by belt conveyors are often in the powder state (eg small coal, gypsum, etc) and during the transport there is a possibility of polluting the environment around conveyor route. A good solution for this problem is the pipe conveyor, where a belt is closed on the route in circular shape and flat on unloading point. Another problem which is indicated in the paper is dusting on the belt conveyor boosters. In Poland a new solution of booster has been designed, whereby dustiness of transportation powder materials is reduced by up to about 90 per cent.

Jan 1, 2003

By Smith T. N, Wild M. B, Elliot B. J

The process of flash smelting of nickel sulphide ores, as practised at the Kalgoorlie Nickel Smelter, is described. The critical variables in the operation of this process are identified. The design of a pilot-scale, turbulent-jet flash reactor which models the essential features of the industrial smelter is described. A report of its operation and application to an investigation of the ignition of particles of sulphide species is given.

Jan 1, 1991

By P Campi, M Dodds

The EastLink project is a 39 km tollway to the east of Melbourne and includes twin three-lane 1.5 km driven tunnels. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley to help preserve the unique flora and fauna in the area. This paper describes the process of transferring the support requirements from the ædrawing boardÆ to the tunnelling face by integrating the temporary support design with the contractorÆs tunnel excavation and support procedures, including sharing of responsibility between the designer and contractor for selection of the support type and the production of a project specific rock mass classification system to enable more objective determination of ground conditions. The methods developed during the design phase incorporated a formal system of reviews, support selection and feedback by monitoring tunnel and ground responses. During construction, the process was implemented using a set of simple documentation and regular structured communication between the contractor and the designer.  

Jan 1, 2008

By Toomey P. T

In many open cut coal mines, rivers and large creeks can cause planning and operating difficulties, both in the terms of the more obvious location of the current watercourse, but, and sometimes more importantly, past meandering of the watercourse. Prevent and past flow regimes may have deposited large alluvial sequences within the current mining areas. The presence of groundwater within the alluvium further complicates the planning and operating practices.A situation exists at Saraji Mine in which alluvial sediments overlie a massive sandstone sequence which in turn lies at about one metre above the coal seam. The problems encountered include high levels of groundwater ingress to the pit, highwall instability, and an unacceptably high rate of blast hole collapse (prior to charging with explosives). Other aspects of the dragline stripping operation were also affected.

Jan 1, 1992

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998

By S Raval

The estimation of greenhouse gas emissions from coalmines is increasingly becoming a priority for both operators and regulators. At the same time, involved scientific challenges in the methane measurements is generating significant interest from global research community. Various technology providers are also actively engaged in improving their sensors and platforms to address the measurement challenges and capitalise the market opportunities. This presentation highlights rapidly evolving multifaceted landscape of coalmine greenhouse gas emissions. It covers the advances in sensors for the detections, including ground-based, airborne, and satellite-based systems as well as models for the emission estimations, including attempts to reduce the involved uncertainties.

Sep 1, 2024

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

By F Mwijage

"The benefits of measuring blast movement to reduce ore loss and dilution have been recognised by many people for many years and various methods have been used with limited success. Geita Gold Mine is running the pilot study on the blast movement monitoring (BMM) system which is a revolutionary method developed and patented by the University of Queensland and Blast Movement Technology (BMT). The system consists of directional transmitters placed within the shot prior to blasting, which are then located after the blast with a special detector and then the data is processed with purpose-designed software.As part of continuous improvement on grade control, Geita Gold Mine is running a research project in all operating pits with the objective of: quantifying the three-dimensional blast muck pile movement and finally utilise the movement data to define post-blast ore polygons and incorporate the movement dynamics during block modelling,quantify the potential savings for ore loss and dilution,improve mine geologists knowledge of blast dynamics, andstimulate greater co-operation between drill and blast engineers and geologists to achieve optimum blast designs.To any operation with selective mining, it is critical to the economics of an operation to control ore loss and dilution; getting it wrong will result in significant lost revenue. Implementation of ongoing pilot study on electronic balls as determinant on blast movement dynamics on ore would be of longer term solution and big investment pay back.CITATION:Mwijage, F, 2012. Pilot study on blast movement monitoring at Geita gold mine, in Proceedings Narrow Vein Mining 2012 , pp 49-58 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

The Shamrock Gold Mine has been brought from exploration to production within three years. Mining of the openpit is scheduled for June 1990 with commissioning in April of the 180 000 TPA carbon-in-pulp mill on old tailings and rock dumps. The development of a small openpit containing 344 000 tonnes at 3.6 g/t Au in a complex sulphide ore has required extensive metallurgical testwork to optimise recovery, and ensure profitability. The project has been undertaken in a changing economic climate, with increasing restrictive legislation. The decision to mine was further complicated by the escalating cost of installing a heap leach operation in South East Queensland. Decreasing costs of consumables, in particular sodium cyanide, and the opportunity to purchase a suitable transportable mill at a reasonable price made the project robustly viable as a CIP operation.

Jan 1, 1990