Search Documents

By Hargraves A. J

At 4 MPa gas pres ure and 30°C the sorptive capacity of 10 selected Australian dried coal ranges from 17 to 23 m3/tonne of CH4 and 27 to 36 m3/tonne of CO2. Values for moist coals are about 25 per cent less. At 20°C, sorptive capacities are about 18 per cent greater. No clear relationship between coal rank and sorptive capacity was established.The permeability of coal to gas is dramatically reduced by progressive hydrostatic confinement. No single 'permeability' for a coal can be established because of relative affinities of coals and the gases (Ar, CH4 and CO2) used in experiments. Bedding plane permeability is significantly greater than permeability normal to bedding. Dependent on gas/coal combinations, permeabilities without confinement ranged from 150 to 0.05 millidarcies, and with 8 MPa hydrostatic confinement from 1.0 to 0.001 md. Generally, permeability is increased by reduction in temperature, and reduced by increase in moisture as one changes from Ar through CH4 to CO2. In retrospect, it is preferable to ubject permeability sample to 8 MPa hydrostatic stress only once, because changes occur in the samples and it is difficult to use other gases successively.The initial rate of desorption, DP, does not appear to be a reliable index of proneness to instantaneou outbursts for Australian coals.The methods used for determining quantitative gas-coal properties appear suitable and reliable for testing other coals.

Jan 1, 1985

By R Turner, P Hatherly, T Medhurst

Borehole geophysical logging data are routinely acquired during exploration of coal deposits in Australia. These data are commonly used qualitatively to identify and correlate coal seams and geotechnically significant interburden rock units. Some quantitative analysis, such as using sonic logs for rock strength estimation is becoming increasingly widespread. This paper discusses results from a project aimed at expanding the quantitative approach to more detailed mineralogical and lithological analysis, which leads to improved geotechnical characterisation for mine planning and mining hazard reduction. A standard suite of wireline logs measuring density, natural gamma, sonic and neutron were analysed from three coal mines in the Bowen Basin. Thirty-nine samples from cored sections of the boreholes were analysed by X-ray diffraction, spectral gamma counts and hyperspectral scanning. Using a standard petrophysical approach to calculating porosity, shale and matrix components from a combination of density, natural gamma and neutron logs, a good correlation with observed mineralogy was demonstrated. However, unusual mineralogies such as heavy minerals or low-potassium clays may distort this analysis. Simultaneous evaluation of all available geophysical logs by modern data mining methods was able to show how these ambiguities may be solved.

Jan 1, 2006

New Caledonia, Norfolk Island and northern- most New Zealand lie on a long, narrow, ridge system, the Norfolk Ridge System, which is sit- uated in the centre of a geologically complex region of ridges and basins between Pacific Basin oceanic crust and continental crust of Australia (see Eade, 1987).

Jan 1, 1987

Host minerals for gold have been of great interest to exploration geologists and metallurgists for a variety of reasons. The depletion of high grade ores in many parts of the world requires that greater attention be given to the study of host min-erals for gold. Some host minerals have been employed in exploration as traces for gold. They are also essential in the design of extraction processes for treating gold ores.This paper reviews the mineralogy of important gold deposits of Papua New Guinea (PNG), Indonesia and New Zealand and focuses attention on the ore minerals and rock-forming minerals that host gold.

Jan 1, 1994

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By B Hall

In feasibility studies the choice of optimum cut-off grade is typically based on an evaluation of tonnage grade curves and manual design of stopes at one or two cut-off grades. In the industry these stope designs are usually based on break-even cut-off grades, but there is little consensus on what cost and price assumptions ought to be included. A new tool for automated stope design has been developed that generates sets of stope shapes for a nominated range of cut-off grades, or depending on the nature of the mineralisation, cut-off values based on net smelter return calculations in the block model. The stope design procedure includes constraints in stope and pillar geometry for the selected mining method and can be used to evaluate sublevel interval and sensitivities to other design parameters in the specific geological and geotechnical environment. These ænested stopesÆ are analogous to ænested pitsÆ in open cut design, and can be used as a key input in the æhill of valueÆ methodology for the evaluation of the optimum cut-off grade in underground design. The results of many consulting studies indicate that a break-even cut-off grade will not be the optimum cut-off grade. A particular benefit of the new stope design tool is that the design rules used to establish stope shapes in the feasibility study can then be used in mine production, in an optimal and repeatable method. This methodology is being advanced in the AMIRA P884 PRIMO project, which is a new research collaboration coordinated by AMIRA International. The project has brought together active research groups in Australia and Canada, with the goal of developing a flexible framework and set of software tools for optimisation in underground mine design.

Jan 1, 2009

Conditional simulation is a branch of geo- statistics which allows the simulation of a mineral deposit so that predictions can be made about the variability of some particular parameter of the deposit. A summary of the general principles, advantages and limitations of conditional simulation is presented together with an example based on coal seam thickness.

Jan 1, 1981

New Zealand Steel Limited is nearing completion of the environmental reporting and planning procedures for its proposed fivefold expansion to steelmaking at Glenbrook, and supporting mining operations at Waikato North Head. A report on the proposal to transport concentrate from the mining operations to Glenbrook has also been prepared and is awaiting release. This paper draws from these events, and by discussing some of the problems encountered, gives some guidelines for the preparation of an Environmental Impact Report.

Jan 1, 1981

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

By Bell LC

Overburden removal, mining and reclamation are now accepted as the basic operational steps involved in the winning of coal by open cut methods. To attain the lowest operational cost, the recontouring and revegetation of spoilpiles must be planned concurrently with the planning of overburden removal and mining. The earthworks associated with reclamation work on spoilpiles often account for 75 - 90 per cent of total reclamation costs. Experience at Callide Mine has shown that the way that spoilpiles are contoured does influence water retention and can reduce erosion from rainfall run-off. However, provided the recontoured slopes meet'Mines Department specifications, the quality of reclamation work is judged not by the quality of the earthworks but by the plant regrowth on the reshaped surface. Thus it is the quality of the revegetation which is of prime importance. For vegetation to be successful, time must be spent on planned research into methods of overcoming plant nutrient deficiencies and selection of suitable grass and tree species. The research programme undertaken at Callide Mine consists of three stages :- laboratory studies glasshouse trials field trials

Jan 1, 1978

By Fazakerley VW

The Murrin Murrin deposit is located about 210 km NNE of Kalgoorlie and 50 km E of Leonora in the North Eastern Goldfields region of Western Australia at latitude 28¦ 50'S. longitude 121¦ 54'E on the Laverton (SH 51-2) 1:250 000 map sheet. The tenements are held by Anaconda Nickel NL. Geological investigations between 1994 and 1996 resulted in resource calculations being completed for the ten lateritic nickel cobalt deposits shown in Figure 1. At a 0.8 per cent nickel cut-off the resources at May 1996 for the nine deposits are 116.8 Mt at 1.10 per cent nickel and 0.082 per cent cobalt. The nickel-cobalt mineralisation is contained in a laterite profile developed over Archaean serpentinised peridotites. A bankable feasibility study has been completed and the project is scheduled to be in production by the beginning of 1998.

Jan 1, 1996

By Okura T, Hino J

Coal utilization for copper flash smelting in Japan was initiated due to the sudden upheaval in the price of oil in the last ten years. A major portion of the heavy fuel oil has already been replaced by coal resulting in a corresponding decrease in energy costs. In addition to energy cost savings, an interesting metallurgical phenomenon was observed in flash smelting operations. Unlike oil combustion, coal is not burned completely in the shaft. A considerable fraction of coal particles remain on the surface of slag and are burned at the settler. Chemical investigation has shown that oxygen potentials at the settler have consequently decreased, bringing the slag and matte phases into reducing conditions, thus oxidation and reduction can coexist in one flash smelting unit. As a result, a decrease in magnetite and copper contents in the slag, elimination of furnace hearth build-up and dissolution of intermediate layer between matte and slag have been observed. In general, these led to improvements of furnace operations. However, thermodynamic investigations have shown that some minor elements such as As, Sb, Bi and Pb concentrate from slag to matte. Results evaluated on the basis of thermodynamic data relatively agree with practical observa- tions. Consequently, for coal utilization in flash smelting operations it will be necessary to control oxygen potentials from the stand- points of copper loss in slag and minor element Distributions.

Jan 1, 1987

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

By Vernon PN

The Eossing Uranium Mine is a high tonnage low grade open pit operation using acid leaching for uranium extraction and ion exchange and solvent extraction for solution purification. Advanced technology, much of it computer based, has led to major economies that have contained operating unit costs over the last four years in the face of double figure inflation. An improved ore reserve block model and mine planning system have achieved a considerable reduction in the stripping ratio. Drilling and blasting costs have decreased some 25%, mainly by the introduction of heavy ANFO explosive. A centralised computer control centre for the metallurgical plant has increased labour productivity resulting in improved process control. The all-staff workforce is united with management in the objectives of creating a safe, healthy, working and living environment and a prosperous company, capable of contributing to the wellbeing of the nation and the shareholders. This situation has been brought into being by an equal opportunity policy coupled with a management system emphasising open two-way communication through all levels in the organisation. The success of this policy is highly apparent in the morale and productivity of the workforce.

Jan 1, 1986

Rare-earth permanent magnetic roll separators, pioneered by our group a few years ago, have distinctly different operation characteristics compared to prior art electromagnetic separators of various types. Many new applications for dry high-intensity (or better: high-force) magnetic separation have been developed in a short time period. It has also been found that the new generation of separators generally are more efficient with regards to removal of weakly magnetic contaminants in glass and ceramic raw materials with minimum loss of valuable product compared to induced magnetic roll (IMR) separators.The latest development is in the area of production of clean magnetic concentrates at high recoveries. It is likely that the PERMROLLR magnetic separator will replace cross-belt and lift-type magnetic separators as a result of this most recent advance.The paper will review the features of the PERMROLLR magnetic separator in comparison with other types of magnetic separators on the market and give examples on applications.

Jan 1, 1990

At the LKAB, Iron Ore Mine, Kiruna, Sweden a preliminary investigation into the reliability characteristics of a fleet of load-haul-dump machines has shown that the hydraulic system is one of the most critical parts. Therefore, hydraulic system was selected for study and analysis through condition monitoring devices so that failure can be controlled or at least the failure consequences can be minimized.The hydraulic system has two different problems; one is that the contamination level is too high and the other is high temperature during operation. At high temperature, seals and tubes are a problem, because they stiffen due to carbonization, which leads to increasing leakage. The pumps and restrictions were responsible for the main temperature increase.

Jan 1, 1991

By King ND

This paper presents an economic study comparing two gold recovery processes, zinc precipitation (Merrill-Crowe) and carbon-in-pulp (CIP). Capital, operating, and gold losses costs from an actual CIP plant study are compared to costs developed from a hypothetical Merrill-Crowe process flowsheet. ' Results indicate an overall economic advantage to CIP over Merrill-Crowe for plants processing slurries within the range of the five gold solution grades selected for this study.

Jan 1, 1982

By Gray N. B, Floyd J. M

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

The provision of electrical power is an important consideration in project develop- ment. The first step to be taken in this area is to assess the power requirements of the project. The alternatives of taking a supply from a power authority or providing local generation can then be considered. This requires additional definition of the prob- able characteristics of the supply. The availability of authority power in Australia is limited by the extent of the state power grids. Recent developments now allow these grids to be extended and their load capacity increased to meet major load increases at less cost than was possible pre- viously. The options for local generation include diesel, gas turbine, steam, hydro, solar and wind, each having its particular performance characteristics and costs. The choice of fuel for diesel, gas turbine, and steam plant likewise involves consideration of a range of factors. The arrangements adopted for a number of development projects illustrate some of the aspects which influence the decisions on power supply.

Jan 1, 1986

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983