Search Documents

By Jaczkowski B. M, Cox T. J, Domfeh I. A, Stalker I

Mining and treatment of gold ore in the Ashanti region at Obuasi, Ghana has been continuous for more than 100 years. Earlier production from this world class deposit can be traced far into the history of West Africa's gold trade. As part of a general development and expansion program, Ashanti Goldfields Corporation (Ghana) recently undertook a program to heap leach oxidized near surface ore. Kappes, Cassiday & Associates was given a major role in the design, equipment supply, installation and start-up management of the 3000 tonne/day heap leach. Unusual conditions included a high annual rainfall and an ore which could be characterized as a soft, decomposed, water saturated schist. Production began in March 1990. Startup problems and their solutions are discussed.

Jan 1, 1991

By Collins J. L, Fytas K

Surface mining accounts for more than 50% of the world's total mineral production. In future years this status is expected to change somewhat in favour of surface mining. The production technology during the past decade has concentrated on greater degree of mechanization with high capacity heavy duty equip- ment. This trend will continue. Next two decades will also see microproces- ,or based equipment, health and performance monitoring and management information systems fully integrated with excavated and material handling systems which in themselves will be amenable to auto- matic and remote control. Computerized mine planning will also be integrated within the system providing a fully integrated planning, excavat- ing and materials handling system. The surface mines of the 1990's and beyond will be so computer dependent that manpower will be reduced to one third of current levels.

Jan 1, 1988

By Just G. D

The results of a geostatistical analysis of geochemical data obtained from field measurements are described in the paper. Q values derived from seismic signal rise times for different travel paths in the rock masses were used in the study. Cross-hole seismic measurements made at surface and underground sites formed the basis for the work. Geostatistical estimation of average l/Q values for area of the rock were compared with geological interpretions of rock type distributions. Reasonable correlations were obtained between the two methods of rock quality estimation.

Jan 1, 1988

By Mills KW

Coal mine pillar design formulae available to mine planners are typically based on relationships determined for specific site conditions. Application of these methods is difficult when other factors, relating to mining or geological conditions, not specifically addressed in these relationships are encountered. A review of pillar design methods, coal strength properties and relevant field monitoring of pillar behaviour has shown pillar strength and deformational characteristics are extremely sensitive to in situ behaviour of the rock and other material components that make up the coal pillar system. A method has been developed that has been found to provide excellent correlation between existing field data using the strength and deformational characteristics of materials determined in selected laboratory tests. This method is based on definition of the loading conditions, accurate modelling of the strength, confining conditions and deformation occuring in the roof, floor and coal seam and definition of the in situ strength of coal based on underground monitoring of appropriately sized coal pillar. The design method is considered to provide an accurate and rigorous pillar design method that will give mine planners a more rational mine design capability which is based on the mine geometry and geological setting of the operation. It is envisaged that availability of such a method will allow significant optimisation of pillar layouts and more closely define the geological and mining issues that relate to pillar design optimisation.

Jan 1, 1992

The Carnilya Hill Mine, a joint venture project between Western Mining Corporation Limited (WMC) and The Broken Hill Proprietary Company (BHP), is a nickel sulphide deposit being developed by the Kambalda Nickel Operations (KNO) of Western Mining Corporation. Seven months elapsed from the time a decision to proceed with the project was taken until the first ore production. During the first month of operation a new KNO record for decline development was set. Equipment used includes an electro- hydraulic drill jumbo, 4 cubic metre front end loaders, and 35 tonne haulage trucks.

Jan 1, 1981

Silver-lead mineralization at Indooroopilly, Queensland, extends upwards from Upper Triassic rhyolite which intrudes phyllite-containing Palaeozoic mineralization.Sulphides and magma were emplaced in a special structural site which underwent dilational fracturing while surrounding rocks were block-faulted and compressed. This site lies at tbe intersection of dykes, faults, and a lineament adjacent to a Middle Triassic granitic stock.Structural controls at Indooroopilly are attributed to the effects of piston faulting. Exploration for similarly controlled deposits should be directed towards structural intersections near stocks or batholiths which have intruded mineralized belts. Priority should be given to structural intersections which were sites of block-faulting and igneous activity under compressional tectonic conditions.Favourable sites lacking surface mineralization may contain ore at depth as piston faulting produces 'blind' ore deposits.

Jan 1, 1976

Blasting in Norwegian mines is often carried out by contractors who tend to look for the cheapest solution, without concern about fragment quality. The requirementsfor a contractor are usually only related to the maximum size of boulders and the quantity per month. Even when the owners of the mine are responsible for blasting, very little effort is made to optimise the blasting process. This paper presents test methods which were used and results from small-scale and full-scale blasting tests. In the small-scale tests, cubes 500 x 500 x 500 mm of four different rock types were blasted in a chamber, using two types of dynamite explosive. The velocity of detonation (VOD) for the dynamite explosives was 3000 m/s and 6000 m/s respectively. Three cubes of each rock type were blasted with each type of explosive, and a total of six cubes of each rock type was used. The entire muckpile (approximately 350 kg) was- sieved and weighed after each blast and fragments between 8-16 mm were tested for impact values and flakiness. The results of these tests clearly showed improvement in fragmentation the closer the acoustic impedance ratio of the explosive (VOD x density) over the rock (Cp density) was equal to one. The results also showed that the quality of the fragments (in terms of impact values) tends to be better when the cubes are blasted with the high velocity dynamite.

Jan 1, 1995

By Jury C. G

A decade of expansion and high production targets have led to changes in the number and structure of the Mount Isa Mines Limited work- force. Falls in labour turnover and absenteeism are correlated with two demographic variables, improved selection and placement procedures and home purchase facilities. Some results of recent population surveys are presented and discussed in terms of future housing needs and potential employment problems encountered by school leavers.

Jan 1, 1974

The Lennard Shelf is an Upper Devonian carbonate reef complex striking northwest for 350 km along the northeast margin of the Canning Basin. Numerous small Mississippi Valley type (MVT) Pb-Zn prospects occur within this belt, including the Wagon Pass prospect, located 105 km east of Derby in the Napier Range. At Wagon Pass, the base of the Upper Devonian sequence is a cobbly, dolomitic sandstone, the Van Emmerick Conglomerate. This is conformably overlain by the Frasnian to Famennian Pillara cycle Lower Napier Formation fore-reef deposits. These are characterized by red algal wackestones and terrigenous stylo- bedded packstones, with common dolomitization. The conformably overlying Famennian Nullara cycle contains a classic reefal assemblage, consisting of flat lying Nullara Limestone back-reef, fore-stepping massive Windjana Reef, and steep basinward dipping Upper Napier Formation marginal slope. The Nullara cycle is not dolomitized. The Wagon Pass mineralization is hosted by Lower Napier Formation dolomite. Mineral- ization consists of complex intergrowths and semi-massive assemblages of sphalerite and galena, with subordinate pyrite, marcasite, chalcopyrite, bornite, digenite, covellite and bravoite. Ore textures include granular and colloform. Gangue minerals are dolomite and very fine grained green chloritic clay. Although mineralization commonly occurs as reticulate fracture fillings, its overall distribution is stratabound. Ore paragenesis involved early "diagenetic" dolomitization, followed by breccia formation with chloritic and granular dolomite matrices. Main stage galena-sphalerite mineralization then occurred, accompanied by pervasive chloritization of silty units. Ore genesis was probably related to basin-derived "oil field" brines, with open space textures in the mineralization quite comparable to textures seen in Canning Basin dolomitic hydrocarbon reservoirs. Fluid inclusions in the host dolomite have typical MVT homogenization temperatures of 70-1150 C, and contain minor organic phases. The Van Emmerick Conglomerate, with its high porosity, dolomitization and weak Pb-Zn anomalism, was probably the aquifer for the mineralizing brines. Access of ore solutions to the Wagon

Jan 1, 1986

By Turco E, Pelizza S, Vona A

Within the project against pollution in the Gulf of Naples (Italy) it was envisaged to build a sewage collection tunnel whose tunnelling section is about 30 m2 and whose length is over 4 km. The formations to be bored through feature heteregeneous volcanic deposits made up of either lenses or lava, lapilli and pozzolan layers and ashstone silts. The cover ranges between 10 and 30 metres. The surface is heavily built-up requiring then an accurate monitoring and reduction of noise, vibrations and settlements. The building of the tunnel is therefore carried out by means of a boom tunnelling machine equipped with a mechanized shield. Support along the complete excavation perimeter is provided by linerplates together with an immediate cement grouting behind them. At a later stage the concrete lining will be cast in place.

Jan 1, 1987

By Williams M

Sheet flotation is a new two dimensional column flotation cell that produces continuous spectrum of products. Analogous to a shaking table in its performance and analysis, sheet flotation is a sheet of bubbles rising through packing contained between two walls. Feed enters the sheet at the lower left and the product exit along the top and right edges. Iligh grade materials exit at the top left, middlings exit at the top right comer and low grade waste materials exit at the bottom right. As in the case of a shaking table, two motions are required: up and right. Bubbles furnish the upwards movement for hydrophobic particles, slanted packing the rightward movement for hydrophilic particles. The sheet flotation cells is analysed as a 40 x 40 array of simple cells. In practice, 1000 x 1000 arrays of simple cells may be expected. With larger arrays, excellent separations may be expected. Because there is no recycle, there is no build-up of middlings in

Jan 1, 1993

The Electricity Generating Authority of Thailand own and operate an opencut mine supplying coal to on-site power stations at Mae Moh, 600 km North of Bangkok. The mine is being expanded from an annual production of 1.5 million tonnes per year in 1982 to over 9.5 million tonnes per year by 1991. The mine will be amongst the largest open pit operations in the world. It is technically difficult to operate and plan due to complex geology, weak strata and surface constraints including reservoirs, forests and traditional villages. This paper presents a case study of mine planning for the above project including associated collection and processing of geological and geotechnical information. The existing operation is described, as well as the strategy adopted for the mine at expanded production. The planning covers various phases of mine planning including a Conceptual Study, a Definitive Study and detailed short term planning. Each stage incorporated new information and reflected a higher level of confidence in the data and resulting plan. Sophisticated computer techniques were required including geological modelling, calculation of volumes, geotechnical analysis, scheduling and costing. The planning was undertaken on site by a team of Australian and Thai Engineers as part of the Thailand-Australia Lignite Mines Development Project which is a four year programme of assistance funded by the Australian Government.

Jan 1, 1986

By Chitombo GP

The proposed guidelines on vibration limits that have been circulated by the Australian Environmental Council, demonstrate the need for an extensive data collection and evaluation program to avoid the enacting of abritrary and costly legislation. The operational or practical influence of blast design and overall economic implications of legislation which further reduces permissible levels of ground vibration are discussed. In a typical blasting operation, blast sizes could become smaller and blasting correspondingly more frequent to meet pro- duction demands. Blasthole diameters and charge lengths could be reduced, increasing drilling costs and associated labour costs. Blast size however, is frequently controlled by factors associated with machinery, grade control, pit control, stope size, production contract levels and other factors which cannot be readily changed for operating mines. Blasthole diameters are frequently deter- mined by existing drilling equipment, length of holes (depth of ore or stope size), geological structure and other factors which are not easily changeable. Typical large scale open stoping and strip mining opera- tions are analysed as case studies. The effects of extreme leg- islative limits and the corresponding operational changes with respect to variations in production costs are discussed.

Jan 1, 1987

By Carlson BL, Overton DD

This paper compares the designs of heap leach facilities for four precious metal mining projects in the southwestern United States. These four proposed projects are of small-to medium-size relative to other operating mines in the United States, and are either permitted or in the final stages of permitting. The differences and similarities in the heap leach facility designs are compared with respect to site conditions, operating conditions and regulatory requirements. This comparison provides a summary of the state-of-practice for heap leach facility design in the southwestern United States and identifies current issues in project development and process material containment.

Jan 1, 1997

By Hunter T. C

The wirebar furnacing and casting facility commissioned in 1970 at Copper Refineries Pty. Ltd. (CRL), Townsville, comprising a 70 tonne/ hour ASARCO shaft furnace and a Walker type casting wheel, contained several unique design features. Since commissioning, effort has been directed at improving metallurgical control of the casting process. This has resulted in the identification of optimum mould lubricant properties and the use of continuous on-line measurement of molten metal oxygen content. Casting defects such as cracks and surface porosity are readily explained and controlled using these techniques.

Jan 1, 1977

The Central West of New South Wales is emerging as a significant metallogenic province. The development of Northparkes Mines (North Limited) and the Cadia Hill deposit (Newcrest) are establishing NSW as a highly prospective porphyry copper-gold province. Exploration in the area has been further buoyed by the Ridgeway discovery by Newcrest near Cadia. The fact that the Ridgeway prospect was discovered 300 m below surface under Tertiary basalt cover indicates that surface prospecting can no longer be considered alone as an adequate method to find significant new deposits.

Jan 1, 1997

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000

The thick coal seams of the South Maitland field are the only ones in New South Wales which have been worked extensively to heights beyond 3.8 m (nominal "thin" seam height). Under shallow cover only minor difficulties were experienced in developing first workings but later the widespread occurrence of incidents of spontaneous combustion and the growth of "creeps" extending over large areas gave the field its own peculiar problems. As the mines have driven under deeper cover extreme difficulties in forming development roadways have been experi- enced. Various methods have been adopted in an attempt to overcome the problems of the field.

Jan 1, 1976

By Purvis A. H, Greenwood-Smith R, Sowerby B. D

A nuclear technique for the determination of copper and nickel in bulk samples and drill core has been developed at Lucas Heights andfield-tested at Mount Isa. The technique, which is highly specific to the element being measured, utilises the gamma-ray resonance scallering process.A bulk mineral analyser was installed in mid-1976 for the routine assay of copper in bulk samples and drill cores, and remained in operation until late 1981. The operation of the analyser over this five-year period is reviewed with particular emphasis on reliability, accuracy and principal usage.The main application of this analyser was in stope planning and design whereby several thousand drill-core and Wall-chip samples were analysed. It was also used as an aid to underground grade control of stopes where ore dilution by supporting barren backfill was a problem.

Jan 1, 1984

Interest in the sampling of refined copper cathodes has heightened over the last ten years. This has followed the increasing importance of cathodes as the principle trading form for metallic copper. It has also been given impetus by recent trends for quality certification of manufacturing inputs, specifically the AS3900 and IS09000 series of standards.

Jan 1, 1976