Search Documents

Recent operating experience from West Australian open pit gold mines has shown that geotechnical input into initial design is rare. As a result, ground stability is poor - almost half the pits designed in this way suffer major failure.West Australian experience shows that geotechnical studies for individual mines are site specific, and therefore empirical experience cannot be transported from site to site. Geotechnical studies performed prior to design have resulted in significantly improved pit stability.

Jan 1, 1990

By Evans RH, Todd G

Statistical thinking and statistical process ppq;ro4 are essential adjuncts of total quality management aqd too continuous improvement of operating efficiency arid, p*Nc; a4 W,

Jan 1, 1991

By Balks AI

Systematic roof bolting in Australian coal mines began at Elrington Colliery in 19)49. Since that time the proportion of the roof supported by roof bolts has increased until, in 1970, 1.5 million were installed in Australian coal mines. This rapid growth of roof bolting has meant that the range and variety of roof bolting machines has altered also. The-number of machines now available both to bore holes and place roof bolts has increased. to the point where both rotary and per- cussive machines are used extensively. Generally, until the last four years, roof bolting machinery in Australia followed the practices in vogue in the United States. However, in -recent time the particular problems of Australian coal mining have necessitated the development of equipment primarily suitable to Australian conditions.

Jan 1, 1971

Depressed prices for minerals will force the mining industry to became more efficient. The continuous conveying of pit product is one area in which savings can be made. Conveyors are available, or can be adapted to provide the flexibility and reliability required. Each conveying system will need to be custom designed to suit the particular requirements of the mine. The Australian mining industry must take the initiative and accept the challenge of the new technology.

Jan 1, 1986

By Shining Z

The properties of coal or rock containing gas are very important both for studying coal and methane outburst mechanism and for controlling underground rock in mining. The rheological fracture properties of coal containing gas were studied to obtain its rheological fracture principle both in microscopic scale and in macroscopic scale. The application of this principle is successful in explaining coal and methane outburst mechanism and for putting forward a rheological hypothesis of coal and methane outburst.

Jan 1, 1992

By Fulton E, Ring RJ, Waters DJ

Laboratory leach tests of Nabarlek uranium ore carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's Acid1 (permonosulphuric acid) as an alternative oxident to pyrolusite indicated reduced acid consumption in leaching and lime savings in neutralisation of tailings liquors when using Caro's Acid. Interox Chemicals Pty. Ltd. arranged a plant trial for Caro's Acid at Queensland Mines Nabarlek Plant. The trial confirmed that significant savings in acid and lime can be achieved under plant conditions. Plant operations also demonstrated improved redox potential control was possible using Caro's Acid.

Jan 1, 1978

The geographical and geological situations of the two mineral sand deposits currently being mined by Western Titanium Limited and the mining methods in use are briefly described. Production scheduling involving the ability to vary the proportions of the major minerals produced, together with maintaining a constant feed grade to the wet concentrator has been assuming greater importance to the company in recent years as the relative value of these minerals, due mainly to technological advances and environmental considerations, is subject to significant and rapid change. Manual calculation, even using a programmable calculator, became a trade-off between man hours and data usage. Schedules were updated infrequently and only a fraction of the avail- able data was used. In July 1975 a Data General NOVA 2/10 minicomputer with a 24K word core and three cassette drives was purchased. A suite of programmes was developed using BASIC to assist in production scheduling and these were opera- tional early in 1976.

Jan 1, 1977

By M J. Nugus

A substantial cost is invested into the data collection phase of any exploration or development program; notwithstanding, it is impractical to expect a database of information can be collated to ensure a perfect geological interpretation. The question then becomes, is there a possible alternative interpretation and what is the likely impact of the variations? Modelling in 2005, of the Cosmo lode at Sunrise Dam Gold Mine, Western Australia led to consideration of the philosophical implications associated with resource management. It was concluded that several plausible geological models could be constructed from the known geological database. To varying degrees, this predicament is common to all geological reconstructions, as several alternative geological models can be generated at almost any stage that will impact on the resultant resource estimation and mine plan. The significance of that variation and the associated risk of multiple geological models (MGMs) requires due consideration. What is being suggested is that using plausible multiple geological models advances the holistic understanding of a mineral deposit within the bounds of the data collected, providing fluidity for updating geological knowledge and building inherent variability into the design and planning departments where variations of the geological models may materially impact on the resource performance.

Jan 1, 2006

In 1976, The Zinc Corporation Limited Broken Hill set up a plant to re-process a hill of tailing (Mt. Keast) from the original treatment operations. With the likely disappearance of this source of feed in 1985, an investigation was initiated to determine what other feed sources might be available. This involved searching through old records and photographs as well as a subsequent drilling campaign. The paper briefly covers the history of treatment operations and describes, as a result of the information obtained, the likely future sources of feed.

Jan 1, 1983

By Millett R

In January 1989, Western Mining Corporation (WMC) acquired the Perseverance and Rocky's Reward orebodies and associated infrastructure from the Agnew Mining Company (AMC). AMC had closed the operation in August 1986 and it had been on care and maintenance since that time. To return the operation to full production as quickly as possible it was planned to mine the Rocky's Reward orebody by opencut mining and treat this ore whilst the underground Perseverance workings were rehabilitated. Removal of overburden from Rocky's Reward thus commenced immediately with a target of April 1989 for delivery of the first ore to the concentrator. Extensive rehabilitation and upgrading of the concentrator commenced in late January, and continued in stages for an 18 month period. The first stage consisted of overhauling all existing equipment and completing a crusher upgrade commenced by AMC prior to the mine closure. During this period, it was necessary to recruit a workforce and re-establish all the required support structure. In late April the plant commenced commissioning trials on mullock. The first ore was crushed on the 11th May 1989 and concentrate produced the following day. From May 1989 to June 1990 the plant was producing nickel concentrate whilst further upgrading continued. During this period, the flotation capacity was tripled by installation of a bank of eight Wemco 144L flotation cells in rougher-scavenger duties and two 12 metre by 2 metre diameter columns in cleaning duties. The existing vacuum drum filters were replaced by two Larox PF32 pressure filters, eliminating the need for solar drying and allowing the flash drier to be fed direct from the filters. These, along with a major borefield expansion and further work to the crusher increased the nominal plant capacity from 600,000 to 1,000,000 t/yr. The plant achieved the 1,000,000 t/yr rate in April 1990.

Jan 1, 1991

By I Auranen, J Raatikainen

IMA Engineering (IMA) and Mine On-Line Service (MOLS) companies have used on-line sensors for analysing ore and waste rock in mining for more than 25 years. Today IMA on-line sensors are used in various stages of the mining process including on-line analysis of drill cores, drill chips, ore and waste in loader bucket, ROM ore analysis on belt conveyor belt and in bulk ore sorting and in slurry analysis in concentrators. During years of extensive field experience and testing we have found that the waste rock dilution and ore losses create much larger economic and environmental losses than has been previously recognized. According to our studies the main reason is limited number of analysis already in exploration when drill cores or drill cuttings are used in block modelling. The same happens in production because too few and biased samples from benches are used to estimate the ore grade. Much more than today estimated amount of waste enters the mill and considerable volumes of ore losses happen at the same time. The ore grade on the benches and in muck piles is averaged and “homogenized” with averaged and biased samples. These are the main root causes of waste rock dilution and ore losses. Sensor based preconcentration can be the remedy to waste rock dilution and ore losses. This presentation will show examples of the use of on-line sensors in preconcentration when analysing ore and waste rock in drill cores, drill cuttings, on conveyor belt and in bulk ore sorting. Waste rock removal in preconcentration has direct effect on energy consumption in crushing and grinding and chemicals in concentrator. In concentrator waste is separated and goes to tailings pond, however, preconcentration directly reduces the volume of the tailings. In our presentation we will cover cases in base metals and in gold mines.

Nov 10, 2020

By A T. Owen, F A. Benn, J D. Swift, D M. Labbett, A F. Grabsch

The AMIRA P266 æImproving Thickener TechnologyÆ series of projects has sought to provide a firm scientific basis for feedwell and thickener design, a requirement as pressures on water usage in the minerals industry increase. While advanced computational fluid dynamics modelling of feedwell processes has generated the most obvious and successful applications to improving the performance of operating units, such outcomes have drawn heavily on parallel studies into flocculation fundamentals. Central to this has been the development of a linear pipe reactor system that allows the kinetics of flocculated aggregate growth and rupture to be measured for thickener feeds under turbulent pipe flow conditions. This ensures much greater control of the intensity and duration of applied shear than is possible with conventional flocculation test procedures, offering insights into flocculation processes that would be otherwise hidden in time-averaged measurements.

Jan 1, 2009

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

By R Piper

The Yabulu Nickel Refinery commissioned in 1974, processes lateritic ore via a modified Caron process to produce high quality nickel and cobalt products. The Greenvale orebody provided the sole source of feed to the plant until 1990 and with well-blended mineralogy, it resulted in stable and predictable plant performance, allowing the operating focus to be on reducing energy consumption and increasing ore throughput. This approach provided better economics than pursuing increased reduction efficiency. From 1990, increasing quantities of lateritic ore were imported from Indonesia, Philippines and New Caledonia. This introduced considerable variation in ore blends and instability in plant operation but also provided the opportunity to treat higher grade ore blends which yielded higher reduction efficiencies. Ore reduction is conducted using 12 Herreshoff multiple hearth reduction furnaces, using heavy fuel oil as reductant. The æROASTERÆ Project was approved in November 2000 with the primary objective of improving Nickel reduction efficiency by: Stabilising Roaster Operation via a structured program including focused maintenance efforts, capital equipment upgrades, new process measurements, process re-design and improvements to operating skills and process troubleshooting. A structured technical program including laboratory and plant studies using one plant furnace as a pilot unit to develop improved knowledge of how the reduction process proceeds in the Herreshoff furnace. Armed with this knowledge, optimised process conditions and a reduction process model were developed contributing to a significant demonstrated reduction efficiency improvement. Technical input to the project was provided by QNI with Hatch providing the engineering and project management for the $8.5 M capital work. Execution of the work included extensive consultation with the plant operators and close cooperation between the Hatch project team and QNI operations personnel ensuring installations were completed with minimal production disruption. A strong focus on safety management resulted in a number of brownfields project relevant safety initiatives being implemented resulting in project completion without a serious injury.

Jan 1, 2002

A continuous casting machine, of the Concast curved mould design casting billets in four strands, was commissioned at the Newcastle Works of The Broken Hill Proprietary Co. Ltd., in November, 1967. Quality assessment of early casts from this plant indicated that steel cleanliness was sometimes inferior to that of equival- ent ingot cast steel. Extensive trials to develop a modified deoxidation technique were not successful in improving clean- liness to the desired level. A "contra-flow" gas shroud, to cover the steel stream between the tundish and the mould, was developed, and proved successful in achieving the required levels of product cleanliness. The inclusion content of six grades of steel ranging in carbon content from 0.10 to 0.70 per cent is examined, and an attempt is made to explain theoretically some of the results obtained.

Jan 1, 1972

By A G. L Pratt, G F. Dunstan, A Leonforte

The selection of the material sizing and mine dewatering systems are important elements in the development of a large-scale, high tonnage (greater than 4 Mt/a) underground hard rock mine. The sizing system will influence the size and type of the ore haulage system and therefore how the underground project is developed. With more underground developments considering or implementing caving methods of mining, the selection of the material sizing systems is also influenced by the caving fragmentation. Traditionally, crusher systems are used for material sizing in large hard rock mines, with the crusher installation and its ancillary equipment representing a substantial capital investment. Underground cave mining type operations generally express themselves with large surface subsidence areas, which can lead to large inflows of water from major rain events or purging underground aquifer systems. To minimise disruption to mine production, the dewatering system needs to be sized, with consideration to both storage and pumping capacities. The balance between storage and pumping capacity is assessed to provide the optimal economic solution with the appropriate risk measures. This paper outlines a process for the selection of material sizing and dewatering systems for large-scale caving operations. This process is illustrated with information drawn from NewcrestÆs Ridgeway Deeps Block Cave project. The Ridgeway Deeps Block Cave is located directly beneath the existing Ridgeway Sublevel Cave Mine.

Jan 1, 2008

By Miyatani J. Asaki Z, Kondo Y

The oxidation of sphalerite particles of 60 to 100 mesh size was studied in a fluidized bed of low 02 concentration at 900¦C. Par- tial pressure of 02 in the fluidizing 02-N2 gas mixture was chosen between 0.0009 and 0.02 atm. In the region of p02 between 0.008 and 0.02 atm, the oxidation rate was lowered with the decrease of p02, and the unreacted-core model was applied. At lower pbelow 0.008 atm, the reaction rate was enhanced as compared with the calcu- lated values from the unreacted-core model. From microscopic examination, it was found that ZnS was evaporated at the particle surface and the dissociated Zn vapor was oxidized in the gas phase. Initial reaction rate and the distance between the surface of inner sphaler- ite core and the oxide shell were studied based on the model of enhanced oxidation.

Jan 1, 1980

By Kneisley RO

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north- central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield- pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)- wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By Blair J. R

A Train Performance Calculator (TPC) is an essential tool in railway operations, as a means of acquiring quickly a precise measure of the performance of the system. Traditionally the TPC was used in the form of program for a large computer. By employing an efficient integration algorithm and tailoring the program to suit the computer system it is shown that it is possible to devise a TPC for a mini computer. The resulting low running costs and flexibility of operation makes this a useful design tool. This TPC was developed to study problems associated with a single track railway operation. It was applied specifically to study the railway operated by the Mt. Newman Mining Co. Limited in the Pilbara region of W.A. to transport iron ore from the mine to the port. The TPC was used to calculate the effects of changes to locomotive power, to train size, to the track and to the amount of traffic. Its accuracy was checked by comparing its performance with that of the actual trains.

Jan 1, 1977

By Ingham PD

Selection of equipment for a mining operation, such as Mount Isa Mines, requires certain parameters to be correctly defined. Management control is essential for monitoring, improving and future purchase of equipment. Some research is being done independent of supply manufacturers. Observations about future outlook are made.

Jan 1, 1982