Search Documents

By Singh T, Singh D. P

India has limited resources of coking coal. Most of the coking coal seams are located in Jharia Coalfield. These seams were worked in the past by the bord and pillar system in a haphazard manner, which has resulted in honeycombs of old working. Most of such areas are under fire. In order to meet the demand of coking coal in the 21st century, it is essential that the coal locked due to old underground workings is recovered fully by conducting opencast mining to an ultimate depth of 500 m. The major problem envisaged in conducting opencast mining in such areas will be the stability of pit slopes over voids and the behaviour of subsided material in the pit slopes. An attempt has been made to simulate this complex situation from a specific section of the rockmass of a mine in an equivalent material (EM) model. The old workings existing in upper coal seam (V) were simulated by developing staggered bord and pillar workings in two sections and depillaring them. Opencast mining was conducted for recovery of coal locked due to irregular working in coal seam V. The slope instability caused by intersection of the slope with the void, during frontal working (by shovel-dumper combination) was observed in various situations. In this paper, the technique adopted for simulation of a 125 m thick section of rockmass in an EM model is outlined. Adverse effects of staggered workings and

Jan 1, 1988

The mining and resources industry in general has relied on macro separation technologies (greater than 1 micron) through processes which include: ò sedimentation ò flocculation and coagulation screening and filtration ò absorption ò magnetic separation ò chemical leaching and precipitation Essentially, these processes and technologies provide the industry with an effective arsenal to handle most separation requirements to date. Dewatering of solutions is one of the most significant requirements of the resources industry, as practically all mining endeavours use water in their process for leaching, extraction, cooling, dilution or for potable drinking water.

Jan 1, 1989

Until recently, nickel laterite projects have been largely ignored, due to their supposedly higher treatment costs compared with sulphides, and to their perceived processing difficulties. A number of laterite projects in the 1970s were abandoned because of high capital and operating costs, while others experienced severe technical difficulties. Conventional wisdom had it that laterites would not be exploited until most of the sulphide orebodies had been depleted. Why then, have Australian mining and exploration companies started a resurgence of interest in the treatment of nickel laterites? It all began with the Bulong project, which has been under study since 1987, while more recently two further projects, Murrin Murrin and Cawse, have been initiated and are being fast-tracked to take advantage of the current high nickel and cobalt prices. A further project in NSW, Syerston, has also been investigated at bench-scale, but no further development has yet been announced. All these projects have the following advantages: 1. Good location near a major mining centre and,reasonably close to power, water, roads, accommodation and a developed service industry. 2. Straightforward, low cost mining. 3. Low cost of acid or sulphur. 4. Good to very good cobalt credits. In addition, there have been significant technological developments in the design and operation of high pressure autoclaves and high rate thickeners, as well as solvent extraction and electrowinning technology. This has helped to decrease capital costs and technical risks, and has allowed the development of alternative flowsheets to the existing laterite operations (Taylor, 1996).

Jan 1, 1996

Mount Isa Mines Ltd. annually extracts 5.6 million tonnes of copper ore from the 1100 Orebody. All production is by longhole open stoping, with an increasing emphasis on pillar recovery. Drilling and blasting prac- tices have been modified to allow more efficient pillar extraction, with the evolution of a "core and shell" approach. Blast design occurs at the stope design stage, while individual blast preparation is based on detailed ring plans. A programme of blasting research involving surface and under- ground vibration monitoring and fragmentation assessment has been car- ried out in conjunction with production personnel. Drilling and blasting practice in the orebody must continue to evolve with continued research, to suit changing conditions and take advantage of new technology.

Jan 1, 1988

This paper reviews the use of MTU diesel engines in uses such as Off-Highway Vehicles, Rail traction, Generating Sets, Marine Propulsion and Defence Applications, and focuses on a central theme of maximum power in the minimum of space.

Jan 1, 1986

By T Davis

The 500 orebody in the upper levels of Mt Isa Mines in north-west Queensland was mined by sublevel caving and block caving from 1962 to 1969. The hot and reactive rock mass of this orebody provided significant mining challenges including ground temperatures above those resulting from the geothermal gradient. Recently Xstrata Copper has been studying the potential to mine this orebody by modern caving techniques. Part of the study process has included re-accessing the ore zones for diamond drilling and trial development. A cross-cut trial drive, the first primary development into the orebody in more than 30 years, encountered a temperature increase in development holes from low sixties to almost 80¦C in less than 10 m advance. The issues associated with managing this risk include sourcing suitable quantities of reactive ground explosives for a single small heading and the temperature limitations of the explosives and detonators. Risk management outcomes included controls to mitigate the safety and reliability risks relating to misfires. The control that dealt directly with the challenge of continuing development in elevated temperature ground was to cool the holes before and during charging. The most effective and practical cooling medium proved to be water. Rapid rock temperature recharge time meant cooling had to continue as close to firing as possible. Reticulation systems were constructed to allow cooling to take place up until withdrawal for firing. No misfires occurred with the cooling system and additional controls in place. This proved that developing safely and effectively in the elevated ground temperatures of the 500 orebody is practicable.

Jan 1, 2008

The purpose of this paper is to present a detailed account of the development of the Blasthole Diamond Drilling method of stoping now used at the property of Big Bell Mines Limited, in Western Australia.The ore body is one of the large low grade gold deposits of this State, being a continuous lens 1,850 ft. long and ranging in width from 15 ft. at the ends to 120 ft. at the widest part, the average width being 59 ft. It was first worked in 1913 by a local syndicate, and up to 1924, when operations ceased, 64,448 tons of 3.4 dwt. ore were mined from a shallow open cut. Between 1928 and 1932, 15 deep diamond drill holes were put down to test the ore body at vertical depths ranging from 100 to 700 ft. On the information gained from these drill holes, Premier Gold Mining Co. Ltd. began underground explQration. A level was driven at a depth of 253 ft. and crosscuts put out to the full width of the, orebody at intervals of 100 ft. along the strike, all ore broken being put through a sampling plant. On completion of this sampling,' Big Bell Mines Limited was formed as the operating company, and a plant with a capacity of 1,000 long tons per day was erected and mining and milling operations were commenced in 1937. Ore was first mined from glory hole stopes, 65 ft. long, separated by 35 ft. pillars, by benching using conventional steel with changes up to 20 ft., all broken ore being hauled to the main shaft on the...

Jan 1, 1948

By P T. Hick, T J. Cudahy, M S. Caccetta

Dust derived from mining and handling of ore has been identified as a major concern for the mining industry in Australia and may be critical to the future viability of some resource industries (CSIRO, 1999). Operational techniques to derive accurate measurements of anthropogenic dust on vegetation and infrastructure are necessary for the long-term management and monitoring of the environment surrounding mining operations. Airborne hyperspectral VNIR-SWIR systems can potentially provide these monitoring data. This paper outlines a method developed for deriving quantitative measurements of dust quantity on mangroves using remotely-sensed airborne hyperspectral data. The results show that it is possible to detect and quantitatively map iron oxide dust distribution using properly calibrated airborne visible to short wave infrared (VNIR-SWIR) data.

Jan 1, 2002

By S Paciornik, G Schinazi, M H. de Pinho Maur-cio, M B. Vieira, O da Fonseca Martins Gomes, D T. Wagner

Vale (previously CVRD û Companhia Vale do Rio Doce) evaluates the microstructure of sinters in order to understand their characteristics and behaviour in the agglomeration process, and the correlation with conventional quality parameters. Efforts on image analysis development are in progress between Vale and PUC-Rio in order to improve both the qualitative and quantitative evaluation of a representative portion of material. In the present work, digital microscopy techniques were developed allowing this kind of assessment. Employing a motorised and computer controlled optical microscope, low magnification mosaic images covering complete sinter samples were automatically obtained. The mosaics provide a powerful qualitative overview of the whole sample while allowing low resolution quantitative evaluation of the major phases. In addition, quantitative results for phase fractions were compared for the same sample regions at three magnifications (5x, 10x and 20x objective lenses). A single field (1 x 1) at the lowest magnification corresponds to mosaics of 2 x 2 and 4 x 4 images at the higher magnifications. The automated system allows perfect registration between the mosaics and the single image. Changes in phase discrimination were evaluated as a function of optical resolution, and phase fractions obtained by interactive segmentation of the image histograms were compared. While finer dark phases, eg silicates, were only visible with the best optical resolution, coarser phases such as haematite and pores were measured at all resolutions. For haematite, magnetite, ferrite and pores, the largest relative error in area fraction, between the images obtained with the 5x and 20x lenses, was 12 per cent. The results for silicate were less accurate with a relative error of 44 per cent. The results indicate that digital microscopy provides a flexible method for qualitative and quantitative evaluation of these materials.

Jan 1, 2008

Mining operations have been carried out at Mt. Lyell for the past century. Until the 1970's the location of the mines in relation to the surface topography has enabled the mines to drain their copious inflows of water by gravity. Deeper mining has forced the Company to undertake pumping of increasing inflows of water. A major pumping facility is being established near the base of the known ore reserves with a view to serving the future requirements of the mines. The system has a design capacity of 600 litres per second. Run of mine water will be treated in Vertical Flow Settlers to produce clear water and thickened mud, each of which will be disposed of separately. The clear water will be pumped by six 1000 kW conven- tional centrifugal pumps. The thickened mud will be removed by a Hydraulic Displacement System. The rising mains for both the mud and the clear water are stainless steel cased bore- holes.

Jan 1, 1982

The State of Western Australia has a land area of 2 525 000 km2, and is well endowed with minerals and petroleum products. In 1989 - 90 these products were valued at nearly A$10 500 million.

Jan 1, 1992

A very sensitive high-speed two-colour pyrometer was built to measure the temperature of single particles of sulphide mineral, typi- cally 50 pm in diameter, as they burnt while entrained in a hot gas stream. The pyrometer has been used to study the burning of pyrite and chalcopyrite particles and has thrown light on cenosphere formation. Measured maxi- mum temperatures have been compared with values predicted by diffusion-based models. The pyrometer has also been used to study the burning of small captive pellets (2-9 mmm dia- meter) of lead-zinc concentrate.

Jan 1, 1984

By Abraham B. K, Jensen B, Gillies A. D S

The aim of the research was to investigate the feasibility of using an impedance cell and ratio-transformer bridge to measure solids content in coal slurry pipelines. It appeared that this technique could be developed to measure variations in conductance which correlate with solids content. Successful implementation of the measurement technique would have a variety of applications in existing coal wash plants and the potential for automatic process control. A small pilot plant was designed for a feasibility study. This was a closed loop system in which the coal was uniformly dispersed in a tank with a variable speed agitator and then circulated through an external pipe returning to the top of the tank. The impedance cell was located near the end of the external pipe. Slurry concentrations were varied from clean tap water to 50 per cent solids by weight with the addition of weighed quantities of dry coal dust. Ratio-transformer bridge measurements showed that variations in individual observations were equivalent to measurement errors of about two per cent. These probably reflect variations in concentration of the mixture in the pipe. Data for increments in concentration of one per cent indicate that this is about the limit of resolution of the current system. The paper discusses the principles of operation of the impedance cell and measurement system. Results from the pilot study and proposed improvements in the impedance cell design are examined.

Jan 1, 1995

By Alvarez A. R, Garcia H. l

A fuzzy expert system, DIME, has been developed, under Matlab v 5.1. to assess the coal and gas outburst risk in underground mining. Expert systems and fuzzy logic are powerful tools to manage information represented by linguistic statements,

Jan 1, 1998

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

By Deutsch G. P

The output of an underground mine often depends entirely on the mine winding system. -Decisions made--at the design stage affect the economy and operation'of the mine'.througb -its entire life. A modern mine winding installation is an integrated system and its design requires a multidisciplinary approach including expertise in the-materials handling, mining, mechanical, civil, structural, electrical and control engineering fields. The paper-sets out the elements of typical mine wind- ing systems-and describes some of the more important decisions which must be made during the planning and design process, It is no longer.adequate to. base the choice of a system on the pre- ferences and experiences of individuals. Major Australian winding install- ations are usually designed on the basis of overseas experience and some of the detail design is often carried, out overseas. Differences in basic design criteria occur from country to

Jan 1, 1973

By Wu H. W, Jones S. J

Australia wide, over 40 fly-in/fly-out mining operations and other forms of long distance commuting now exist, with coverage of about 5000 employees. The substantial majority of these operations are in Western Australia, with some mines also located in Queensland and the Northern Territory. In recent years new large-scale mining operations have adopted the fly-in/fly-out approach and it is important to note that no new mining towns have been constructed in Australia since the township of Roxby Downs was built in the late-1980s to service the Olympic Dam mine. An examination of fly-in/fly-out mining operations in Australia has been undertaken. A detailed survey undertaken in 1990 has been reviewed and another intensive survey undertaken to establish emerging trends. Results from both company and individual employees point of view have been analysed. A section examines the views of professional employees and the influence of fly-in/fly-out on career development. Bus-in/bus-out coal mining operations are emerging in Queensland's Bowen Basin. These operations commute their employees into the mine site for compressed working schedules while the mine employees' families are domiciled in regional cities such as Mackay. A review of the issues associated with the development of long distance commute coal mining operations in Queensland's Bowen Basin is performed and two case studies examined.

Jan 1, 1997

By Rennie J. W

In the first five years of longwall mining at Pacific Colliery, special techniques of goaf sealing, gas drainage, goaf edge ventilation and goaf sampling were developed and used to o crcome the concurrent problems of spontaneous combustion and high methane emissions. The English-inspired back-return face ventilation system was modified to suit Australian mining methods and was first used as part of a 'Y' ventilation system and more recently was used with a 'U' system of ventilation. In conjunction with this ventilation system, the maintenance of a sealed goaf area was an essential element in the control of the spontaneous combustion in the goaf.

Jan 1, 1988

By Kennewell G. J

This paper aims to present the evolution of the mining method in the Prince Lyell orebody. Initial strategy and practical experience are detailed as are the reasons for and benefits of changes to the method since 1972 when underground mining began. This section of the paper starts with ten series and concludes with 40 series which was completed in 1989/90.In addition, to update the series of papers written by various authors over the past ten years on Mount Lyell, a review of the experience in the current 50 series lift of mining will be given. As well, the basic planning guidelines are discussed for 60 series - the final lift of the Prince Lyell orebody.

Jan 1, 1992

By Dunstan N, Valentine C

Gas power was first used on the Sons of Gwalia mine in January 1911, when a twin-cylinder Crossley engine of 167 hp was installed to belt-drive a 112 kw 550-volt ac generator. This engine was connected with a No 8 Crossley up-draught suction gas producer, using mulga charcoal as fuel.A second Crossley engine, of 400 hp direct-coupled to a 550-volt ac generator, was installed in 1912, and operated by a down-draught wood producer.This was followed by a large Kynoch twin tandem four-cylinder engine, rated at 660 hp, sea level, with a rope drive to the crushing and treatment sections of the plant.These engines operated until January 1921, when the plant and power house were destroyed by fire. After the fire, both Kynoch and second Crossley engines were salvaged and reconditioned and they continued to give useful service for some years.

Jan 1, 1932