Search Documents

By S Januszewski and, G Dirom, D Christensen

Four field test plots were constructed in 1998 on a sloped waste rock surface at the Myra Falls Operations of Boliden Westmin (Canada) Limited to evaluate hydraulic performance of alternate cover system designs. The field test plot cover systems were designed to control oxygen ingress and water infiltration to the underlying waste rock while providing a medium for a grass and legume vegetation cover. The test plots consisted of a bare waste rock surface (control plot), and three additional plots consisting of native compacted till placed directly on the waste rock surface, overlain by non-compacted till. Two of the test plots included a compacted till layer ameliorated with flyash and bentonite, respectively, to improve moisture retention and reduce permeability. The third test plot consisted of a compacted layer of native till overlain by non-compacted till. A performance monitoring system was installed in each test plot to evaluate net percolation and oxygen ingress to the underlying waste rock. In addition, each test plot has profiles of matric suction, water content, and temperature sensors installed at up-slope and down slope locations. A review of four years of monitoring data shows that the compacted till/bentonite cover system has been most successful in limiting the infiltration of meteoric waters and oxygen ingress to the underlying waste rock material. The compacted till/flyash and compacted till cover systems have produced similar net percolation results and neither have functioned well in maintaining an oxygen ingress layer throughout the year. The amelioration of bentonite with till to produce a compacted barrier layer shows promise in reducing water and oxygen ingress at the MFO site, while the incorporation of flyash with the till did not result in a significant increase in performance. The field performance data clearly demonstrates the need for developing field trials prior to full-scale construction, as opposed to relying solely on an un-calibrated numerical modelling to design the full-scale cover system.

Jan 1, 2003

By G Giles

One of the main tools used by mining operations to mitigate the risk of rock burst is the installation of a so-called ædynamic resistantÆ support system. Such systems are designed to absorb the impact of shockwaves created by mine-induced seismic events. Dynamic support must be strong and capable of sustaining high loads and, at the same time, they have to be flexible and accommodate large deformation. A dynamic support system is therefore a system capable of absorbing a high quantity of energy. Ground support systems are composed of rock reinforcement (rock bolts or cable bolts) and surface support (mesh or shotcrete). In terms of surface support, fibre-reinforced shotcrete is increasingly seen as the industry preferred solution when difficult ground conditions are experienced, including areas of high seismic hazard. A thick layer of shotcrete is certainly strong but it is by no means flexible. Normal weld-mesh has some flexibility, but it is not very strong. The Australian Centre for Geomechanics (ACG), in collaboration with Onesteel Reinforcing Pty Ltd, is currently working on a new high-energy absorption mesh that combines strength and flexibility. The new mesh can be installed with a jumbo, in a similar way as the widely used sheet of weld-mesh. This paper describes the development of this new mesh system.

Jan 1, 2008

Based on a principle developed at a South African Mine, the CSIR developed a device with which the alignment of guide rails in mine shafts could be measured. Originally the technique could only be used to obtain guide misalignment values at the bunton sets. At the time this was considered adequate since it was assumed that guide realignment could only be done at the support points anyway. The technology was developed further and now it is possible to obtain æcontinuousÆ guide profiles from the measurements. Software was developed with which a guide realignment schedule can be drafted and the shape of the realigned guides can be predicted. A measuring system based on this technology is being used to conduct guide alignment measurements in shafts. The data is then analysed and a realignment schedule is recommended in consultation with the mine. Such a schedule may be prioritised so that the worst sections in the shaft are dealt with first. The measurement hardware and analysis software are described. Examples are presented that illustrate the principles and highlight measurement errors. A case study illustrates measurements recorded in a newly equipped shaft. A repeat measurement, 18 months later, shows the effect of recommended realignment as well as the change in guide alignment over this period.

Jan 1, 2005

By Trutwin W, Tracz J

The outbreak of open fires underground cause disturbances to the conditions of the mine ventilation process. Thermal and chemical effects due to fire create unsteady, transient states in airflow and the spread of combustion products in the mine ventilation network. Changes in airflow have an influence on the fire, constituting a sort of feed-back between the fire and the ventilation process. This paper deals with a numerical simulation method, which enables the determination of transients caused by fires. The mathematical model, of the simulation method considered, has been based upon a: simple model of combustion of fuel in the airway, unsteady exchange of heat between the fire, airflow and surrounding rocks, airflow in mine ventilation networks and the theory of heatflow in the rocks. Initial and boundary conditions allow the determination of a set of parameters describing the airflow, the propagation of combustion products, the tempera- ture of the fire and flow etc. due to the fire. The simulation method, facilitates a graphical presentation of the spread of combustion products throughout the network. The simulation method has been prepared for an IBM PC/AT Computer.

Jan 1, 1988

By Anderson JDC

Opencast Lignite Mining requires topwall strata of seams to be fully depleted and footwall aquifers sufficiently depressurized. To prevent a spread of the cone of depression into protected wetlands some distance away, alternatives had been investigated such as closing water works, underground slurry wall barriers and recharge by infiltration. As a result of these investigations, the infiltration method has been chosen and in a first phase during the next decade it will utilize as much as 55 x 106 m3/year. Using this approach, the survival of the wet lands is assured.

Jan 1, 1988

By Hagarty KA

At the northern margin of New Guinea there is a fundamental problem related to the relative timing of arc- continent collision(s) represented in the Papuan Fold-Belt (PFB) and backarc spreading in the Caroline basins. New fission track dates from basement and sediments within major anticlines of the PFB indicate that uplift occurred at 4.0 ¦ 0.5 Ma. The timing is consistent with the fold and thrust shortening (more than 100 km) of the PFB which occurred in the Late Miocene/Early Pliocene as evidenced by the deformed Miocene carbonates and Pliocene molasse deposits. However, in northern Papua New Guinea, earlier work has suggested that ophiolite emplacement and associated metamorphism occurred in the late Oligocene/early Miocene.The evidence suggests that the late Miocene/early Pliocene deformation was of considerably greater magnitude than the earlier obduction event. The Caroline Plate lying north of New Guinea has been interpreted as a backarc basin which commenced spreading in the Eocene and ceased spreading in the Late Oligocene (about 28 Ma). The remnant arc presently docked to New Guinea was active in the Eocene and Oligocene and is believed to be the arc related to the formation of the Caroline Plate. The cessation of spreading of the Caroline Plate has previously been interpreted to be due to arc continent collision during the Late Oligocene/Early Miocene, but such a collision is now known not to have occurred. In the Cretaceous and Palaeocene subduction was to the south beneath New Guinea, but "flipped" in the Eocene to give a north-dipping subduction zone far to the north of New Guinea, driving Caroline Plate backarc extension. This backarc basin reached a limiting size at about 28 Ma resulting in the end of subduction. With the continued northward movement of Australia, Mesozoic oceanic crust was obducted southward onto the New Guinea margin in the Late Oligocene/Early Miocene. In the Miocene south-dipping subduction beneath New Guinea commenced until the now extinct Caroline Plate arc collided with New Guinea in the Early Pliocene, causing extensive regional compression and sinistral strike-slip faulting. This new tectonic framework suggests that backarc basins reach a limiting ridge-trench distance of 1000-1500 knm, beyond which "subduction-pull" cannot drive further spreading so subduction and spreading are terminated.

Jan 1, 1987

By Ushakov S

New geological and geophysical in vestigation including our detailed field observation in different regions of the Koryak upland testify that Nor- theastern Eurasia margin eastward of the Ochotsk-Chukotka belt is composed of a collage of allochtonous terranes arcs and sedimentary filling of back- arc basins, which bordered North East Siberia and Chukotka (1)1). Ancient island are assemblages are the most tipical for this region (2-4; shown by heavy line). They are marked by long (500-1000 km) volcanic belts which become younger towards the Pacific up the Latest Jurassic-Neocomi- an (2) to Late Cretaceous (3) and Pale- Gene (4).

Jan 1, 1987

By R K. W Merkle, E Whiteman

The anorthosite complexes and related rock types of the Indian Precambrian shield are primarily associated with either cratons or mobile belts. They were metamorphosed under amphibolite to granulite facies conditions. The major rock types are chromite-bearing meta-anorthosites, amphibolites, basic granulites, pink granites and gneisses. This study was carried out on chromitite bearing samples from Sittampundi Anorthosite Complex (SAC), Tamil Nadu, to evaluate the nature and textural settings of platinum-group minerals (PGM), using state-of-the-art technology. The structure and petrology of SAC were well studied by earlier workers (Subramanian, 1956), but only scanty data on geochemical, petrology and mineralogy of PGM are available. The mineralogy of the samples is dominated by chromite (>70 mass per cent), plagioclase (An90) and chlorite-actinolite with orthopyroxene (En85). Details of the petrological evolution of the Sittampundi complex will still have to be studied further, but indications of magma replenishment at the level of chromite formation and the elevated PGE values associated with the chromitite samples make the Sittampundi complex a promising target for future exploration activity.

Jan 1, 2008

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

By Hughes DC

Coal development in New South Wales can involve a complex series of government approvals, a requirement that results from the coincidence of many development sites with environmentally sensitive areas. The concept of network analysis is applied to the pre- development regulatory procedures leading up to the grant of a coal lease. The network facilitates a quantitative and qualitative analysis of activity schedules relating to pre- requisite statutory approvals. The sequencing of activities (with clear start and finish nodes, identification of sensitivities and time estimates for completion of each phase of the network) provides government and industry with an effective planning tool.

Jan 1, 1983

According to the temporal and spatial distribution of regional metallogenesis, the Pacific Rim can be divided into four global metallogenetic systems. The Asia-Australia W-Sn metallogenetic belt is the typical representative of intracontinen- tal metallogenetic systems. This belt resulted from Mesozoic and partly pre-Mesozoic tectonic magmatism, mainly re- lated to S-type granite of crustal source, that was generated by collisional orogeny combined with oceanic subduction in intracontinental and continental margin settings. Based on the concept of metallogenetic series, there is a group of min- eralised ore types showing a definite spatial and temporal distribution from endogenetic to exogenetic. These metalloge- netic series are widely distributed in the Asia-Australia W-Sn metallogenetic belt, and are well developed in Southeast China. Five metallogenetic series and two petro-minerogenesis evolution models have been established according to their tectonic settings, various types of granitoids and metallogenetic evolution.

Jan 1, 1995

By M T Roche

The Cannington deposit is one of the largest accumulations of silver-lead known. Located 135 km southeast of Cloncurry in North West Queensland (Figure 1), Australia, the deposit is currently in the feasibility stage of its development. The deposit is named after the nearby Cannington Pastoral Property which runs some 25 000 sheep on 'downs' country. The investigations of the Cannington deposit are carried out under the authority of Mineral Development Licences 139 and 144 and Exploration Permit for Minerals 6788, Answer Downs. Exploration for Broken Hill Type (BHT) silver-lead-zinc deposits in the Mt Isa region has been undertaken by The Broken Hill Proprietary Company Limited's Minerals Division (BHPM) since the early 1980s following in-house research which showed that the Eastern Succession of the Mt Isa Block exhibits characteristics which were favourable for hosting BHT

Jan 1, 1994

By M F. Navarrete

During 2003, different plastic stemming plugs (Cats«, Stemtite«, and Taponex«) were tested in EscondidaÆs Mina Sur, to determine the effect on gas retention time when used in conjunction with drill cuttings in production shots with a blasthole diameter of 10 5/8ö. Longer retention times were expected to provide greater fragmentation and muckpile looseness. In order to determine which plug showed the greatest enhancement of stemming retention, 17 trials were carried out û in the first seven tests, only the Cats were used, in the following five tests, a combination of Cats, Taponex and Stemtite were used, and in the last three tests, only the Taponex plug was used. In the last two blasts, drill cuttings were used without stemming plugs as a benchmarking exercise. Blasts were filmed with a high-speed camera, which could record the detonation times of holes using rolls of shock tube tied to stakes at the hole collars, to act as flash indicators. The camera allowed measurement of the time between charge detonation and the commencement of stemming ejection. In order to obtain the statistical parameters of each one of the stemming plugs used in the 17 trials carried out, the Minitab software was used and a data base was created for it, corresponding to each stemming configuration with the retention time obtained from the filming. Once it was determined which stemming plug provided the greatest enhancement of stemming retention, the impact on the fragmentation was analysed using the WipFrag image analysis software to estimate the muckpile size distribution.

Jan 1, 2004

By S Smith

Several styles of copper (Cu) mineralisation are present at Sepon. Large tonnage, low grade skarn and carbonate replacement massive sulfide mineralisation occur within the metamorphic aureole of Permian-aged rhyodacite porphyry intrusions (RDPs). During exhumation and supergene weathering, this primary mineralisation has been upgraded to form high-grade chalcocite enriched zones up to 50 m thick, which comprises the bulk of Cu resources currently being mined at Sepon. Groundwaters remobilise Cu to form exotic accumulations of malachite that are locally hosted in irregular karsts in carbonate rocks, found up to 1000 m from source mineralisation. Khanong is the largest Cu deposit and recent discoveries have been made at Thengkham South, Thengkham North and Phabing. All deposits have formed by similar processes of mineralisation. However, all differ due to local variations in host rock lithology, structural setting, and hydrological conditions. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This paper reviews the role of fill in mining including consolidated fill both histor- ically and currently as determined by a recent survey of the Fill Subcommittee of the Canadian Advisory Committee on Rock Mechanics (CACRM). It covers the application of fill in modern min- ing methods including mechanized cut and fill, undercut and fill, post pillar cut and fill and longhole pillar recovery between stabilized fill. An automated fill preparation plant and recent developments in rotary drilling of hydraulic fill conducting holes are described briefly. The paper also summarizes the findings of some of the important laboratory and field work carried out on the behaviour of fill in Canada, the United States and Australia and again draws on current information obtained from the Fill Subcommittee of the CACRM. Space limitations and unavailability of suitable material prohi- bit the summary of similar information from other countries.

Jan 1, 1973

By Johnson CR, Wilkie G

The aim of the study was to use quantitative mineralogical measurements to predict the processing characteristics of an ore. Samples were taken from a wide range of concentrators processing ores of lead, zinc, copper and nickel. QEM'SEM was used to measure the characteristics of the ore feeding the plant. Concentrate product samples, together with plant operating data were used to give concentrate grade, recovery and grind size information. It was found that the mineralogical measurements correlated well with the metallurgical parameters indicating that these techniques will be very useful for making predictions in feasibility studies and simple plant optimization.

Jan 1, 1989

A survey of derelict and active alluvial tin and sapphire mines in the Emmaville area of northern N.S.W. as the first step in a pro- gramme of similar surveys to be undertaken throughout the State by the State Pollution Control Commission is presented. Thirty nine individual mine sites in the study area were included in the survey and an assessment made of the current level of impact on the environment at each site by assigning values of "magnitude" and "importance" to a number of impacting factors. Results are pre- sented in matrix form and mine sites ranked in order of impact "importance". Examples of alluvial tin, underground tin/arsenic and alluvial sapphire operations are discussed in detail and rehabilitation programmes proposed for implementation.

Jan 1, 1976

By Moon N. T, Torrance A. C

This study has considered the effect of mechanical shock on the resilience of the glass microspheres commonly used to sensitize an explosive emulsion. The damage to the glass microspheres caused by detonating cord, emulsion manufacture and the manufacture of the glass microspheres were considered along with the effect of sensitizer concentration on explosive performance. Reductions of up to 50% in the glass microsphere concentration of an emulsion explosive can result from poor initiation practice, such as the use of high strength detonating cord as downlines during initiation. Laboratory results suggest that detonating cords of strength greater than 3.5 g/metre should not be used as this can seriously affect explosive performance, particularly in small diameter charges. This reduced performance results from damage to the sensitizer elements and recrystallization of part of the emulsion phase.

Jan 1, 1990

By Simpson D, Skopakow J

This paper is one of the series of papers relating to the Melbourne Underground Rail Loop and specifically describes the structural and architectural design of Museum Station. Structural arrangement, loads and design methods of the major temporary and permanent works are briefly described for the main station and entrance works. Planning of the station concourse area, booking halls and entrances are described together with the selection of finishes for all above and below ground areas.

Jan 1, 1981

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999