Search Documents

Viking Holdings Ltd, a Todd Corporation company, is active in the mineral industry through operations, joint ventures and equity investments. Identification and management of risk is key to the success of the company. This paper discusses risk in general terms and in the context of Vikings activities. Reference is made to the current environment and the impact of risk and environment on profitability.

Jan 1, 1997

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By R H. Eric

Surface wave formation induced by a high-strength submerged jet in a bottom blown metallurgical vessels has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations. Experimental results have been discussed in terms of the wave period, wave frequency and wave amplitude with respect to air injection rate and tuyere configuration at a 0.23 m bath height. The results from high speed photography observations displayed the formation of rotating surface waves which circulates within the water model. It was found that the frequency and the amplitude increased with gas injection rate. The wave period for off-centre nozzle orientation was found to be lower than those of the centre configuration. The experimental results also showed that the frequency of a rotating wave increases when the tuyere orientation becomes off-centred . The predicted amplitudes were in very good agreement with the experimental values over a range of gas flowrates between 0.00599m 3/s to 0.01081 m 3/s.

Jan 1, 2000

By Waterhouse BJ

Occurrence data of Tastubian,Sterlitamakian, and Aktastinian (all of Sakmarian Stage of Early Permian) brachiopod genera are analysed by Q-mode cluster analysis, principal component analysis, and discriminant analysis based on presence or absence of genera. Five faunal provinces and their corresponding generic associations persisted throughout the Sakmarian Stage. The additional Sasian Province incorporating the Lhasa and Shan-Thai terranes became recognisable in Sterlitarakian and strengthened in òAktastinian, implying a Tastubian-Sterlitamakian rifting event, followed by subsequent northward drift and divergence from Gondwana, and convergence with Laurasia. The nature of Permian 'Tethys' is discussed on the basis of faunal migration and abrupt changes of faunal provinciality in Lhasa and Shan-Thai terranes.

Jan 1, 1990

By Godresse M, Turczynski G. P J, Driver I. J, Low G, Ozawa N

Geological evaluations of coal deposits have been traditionally undertaken in a somewhat manual manner. Information is collected downhole by chip sampling, coring and using downhole geophysical logging. This information is then interpreted by an experienced geologist to define the coal and noncoal lithological units. Coal units were subsequently correlated to provide data for structural modelling. In recent years a number of advancements in interpretation techniques have been made based on Artificial Intelligence. This paper describes an integrated geological interpretation system based on maximised use of Al techniques. The first part describes the lithological interpretation which uses a number of boreholes with both logged lithology and downhole geophysical logs. This information provides a learning set of data to the neural network. The second part concentrates on the correlation of both coal and noncoal units from borehole to borehole. Problems in this area, in a manual sense, are interpretation of correlation across weathering zones and other geological anomolies. The technique is based on pattern recognition and dynamic programming techniques where a correlation matrix is developed relating all holes with their maximum correlations.

Jan 1, 1995

By J Moncrieff, P Bellairs

The Black Star Open Cut is located immediately adjacent to the township of Mt Isa and is situated in the middle of extensive pre-existing infrastructure including two concentrators, two smelters, a wet fill plant and two shafts. At any one time there are in excess of 500 people working on the surface within an industry-accepted 600 m exclusion zone from Black Star blasts. Apart from the surface operations there are also the underground operations including the lead mine (closed in December 2005) and the Enterprise and X-41 mines that must clear for all Black Star blasts. The application of industry standard blasting exclusion zones (600 m) was risk assessed as imposing operationally prohibitive constraints which could cause significant business interruption due to the logistical challenges required to ensure that all personnel from surface plants were evacuated for each blast and potential for lost production whilst these personnel were not operating the plant. In was therefore an imperative for the blast exclusion zone to be reduced. This was achieved by the: use of a QA/QC team to ensure that relevant drill and blast implementation is within an acceptable tolerance (KPIs) from design; use of high-quality stemming material called HMR, which is a by- product of the concentrating process and is generally sized at -14 mm with very little fines; implementation of appropriate training and support to Black StarÆs own blast crews, reinforcing the need to achieve the designed amount of stemming in every hole; and provision of appropriate support from Black StarÆs management for additional resources to ensure that every blast achieves design within the KPIs but especially in high-risk areas. The blast exclusion zone was successfully reduced after monitoring the flyrock results from more than 176 blasts. Black Star Open Cut now maintains a minimum blast exclusion of 200 m in critical areas; however, general blasting currently uses a 250 m exclusion as this provides additional risk management whilst still minimising the logistics associated with clearing and securing the slightly increased area.

Jan 1, 2007

By Estoque J, Lodrigueza L, Rebillon F

Ore mineralization in Masara consists mainly of gold-silver veins, porphyry copper and pyrometasomatic deposits related to left-lateral movements along the Philip- pine fault system and a later stage of magmatism. These are hosted by pre-Tertiary volcanic flows and volcaniclastics, and comprise a temporal pattern of earlier peripheral copper zone, an intermediate mixed copper-gold area and a later central gold vein system within the Masara sector of the postulated volcanic field. Gold ore emplacement occurred in at least two stages, and shows gradations from a lower mesothermal-epithermal phase passing into a typical epithermal zone, and finally into a truncated, or poorly developed, upper level thermal spring deposit. Orebodies are closely associated with hot springs, solfatara and several magma- related masses, emphasizing their inherent linkage with a geothermal system in the Area.

Jan 1, 1987

By Maxwell HW

Pacific Coal Pty Limited (a wholly owned subsidiary of CRA Limited) managed the interests of six members of a joint venture formed to mine and export eight million tonnes of export quality steaming coal from a mine developed at Blair Athol in the Bowen Basin of the Central Queensland coal fields. The mine is now operated by Blair Athol Coal Pty Ltd. Crooks Michell Peacock Stewart Pty Limited (CMPS) was awarded a project management and engineering contract for the total mine portion. Following a feasibility study, CMPS carried out an Optimisation Study which produced changes to the design of the project, thus resulting in the project budget being reduced by some A$13 million. In spite of a number of late additions to the scope of work, the project was completed at a final cost of A$148 million, many millions below the reduced project budget. The project was also completed several months ahead of schedule. Total services were provided to take the project from feasibility stage through to the establishment of an operational facility and included project management, planning and control, accounting and financial control, as well as the organisation of engineering, procurement, construction, industrial plant commissioning, and technical training matters.

Jan 1, 1986

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

A new gold cyanidation assay technique has been proven for a range of ores, where it has demonstrated benefits of being: ò Accurate (reduces the typical range of assay scatter almost three-fold, and avoids common fire assay interferences). ò Fast (under one hour, providing a quantum shift in space requirement and equipment utilisation each bottle roll can provide over 15 determinations per day). ò Simple (suitable for field application, no high skill or experience requirements). ò Profitable (reduced drilling, drilling time, ore misclassification and/or double handling after mining). ò Cheap (far lower cost than Fire or Aqua Regia Assays, ie LeachWELLTM costs around 10ó for a 20 g sample at 50 per cent solids, proportionately greater for larger samples eg $1 for 200 g samples which address most nugget effect problems). ò Relevant (distinguishes economic. ie cyanide-extractable gold, the only unequivocal value to use for true resource definition, mine planning and grade control). ò Robust (rough bucket chemistry of samplers does not seriously affect results). A new development is the provision of LeachWELLTM CAS, a solution, which also contains optimum cyanide and stabiliser concentrations; and offers greater: ò Safety (the dilute cyanide solutions are stabilised to avoid generating toxic HCN vapours; and present no cyanide dust or flying chips to deal with). ò Ease (a single squirt dispenses precise quantities of the entire reagent suite, avoiding multiple weighings). ò Reduction in total reagent costs. An inter-laboratory comparison on nine ore types, using two assay techniques (Fire Assay and Aqua Regia) involving 45 laboratories, has demonstrated that LeachWELLTM 60X assays for the samples tested, were equally or more reliable than typical Fire or Aqua Regia Assays. There is particularly great benefit in applying LeachWELLTM 60X assays to richer ores in comparison to Aqua Regia assays, which appear to be prone to very significant underassaying depending on individual analyst skills, and which often suffer greater nugget effects. The major impacts for heap leaching are that: ò Using the LeachWELLTM assay technique for grade control, ore of marginal grade is not accidentally discarded to waste or visa versa due to the scatter of assay data inherent in typical small charge (25 g) fire assays. ò LeachWELLTM assays very importantly report only that gold which will be recoverable in the heap, viz that which is liberated - an important factor where the coarse crush often leaves ten per cent of gold unliberated. These impacts are of particular importance for many ores (ie most of those recovered from open pit operations and at the margins of rich ore subject to slurry processing) subjected to heap leaching as the oxide zones often present major problems of nugget effects as well as mineralisation that cannot be accurately assigned through interpretation of clear structural controls.

Jan 1, 1994

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

By Pinghui J

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

By Ibrahim AR

The experimental phosphate mine of abu Tartur has been recently placed into production. Some problems'have been encountered in maintai- ning grade control due to the differences between early block estimates and actual produ- ction grade. An area of 100 km2 is evaluated by using four methods of evaluation , namely polygonal, inverse distance , inverse distance squared and geostatistical methods. The results of calculations are compared statistically with the control values of grade and thickness. The comparison showed that the. kriging technique gave better estimations for the relative ore reserved, while for grades or thickness any of these techniques except the polygonal can be Used.

Jan 1, 1986

By Grimstone LR, Leach JHJ

An analytical technique is described to identify areas of structural disturbance to coal and interseam strata in coal measures. It is based on exploration borehole data which records seam intersections and interseam lithologies. Computerised data bases have been developed to allow processing of large quantities of borehole records. The case study discussed is located in a tectonic setting dominated by thrust faulting. It provides a mechanism for the identification of low angle and bedding plane faults. In addition it allows the preparation of plans showing the areal distribution of the thrust sheets in the statigraphic section throughout the mine prospect. The technique requires the identification of normal undisturbed depositional thickness of coal seams and interseams to be determined. This is done for coal by the identification of coal ply distribution over the area. For interseam lithologies it is based on sedimentological modelling of lithology distributions, related back to the original depositional environments. Variations from the expected values are interpreted as structural Deformations.

Jan 1, 1986

By P Grouhel

In the recent years several new blasting technologies have come into use in surface mines. Electronic initiation, low-density emulsion explosives and modelling software are in regular use throughout the world. In Australia, these new technologies have achieved significant application, largely in open cut coal mines where more than 20 per cent of blasting is now conducted with electronic initiation systems. These new techniques have contributed to the vast improvement in blasting outcomes evidenced by increased recovery of saleable product and faster excavation rates. In large surface mines, OricaÆs unique combination of electronic initiation systems, bulk emulsion explosives and modelling software can be harnessed to target critical value outcomes. This includes targeting better fragmentation, increased ore uncovery rates and better wall stability û all adding to improved mining operation profitability. Orica Mining Services have combined these technologies into a set of offerings called Blast Based Services (BBSÖ). The paper describes applications of these new technologies and possible benefits in large surface mines.

Jan 1, 2007

Records of ex-solution intergrowths with tetrahedrite as a component are rare. Intergrowths of this nature of tetrahedrite with galena have been described by Guild (1917) and Schneiderhohn (1922), and in Broken Hill ore by Stillwell (1926), but both Schneiderhohn (1922) and Gruner (1929) have commented specifically on the apparent absence of exsolution intergrowths of tetrahedrite and chalcopyrite, despite their frequent association in ores, and their related atomic structures. Schwartz (1942), reviewing the literaturerelating to ex-solution among ore minerals, lists only two instances of such intergrowths, one an occurrence of lamellae of chalcopyrite oriented along the octahedral planes of tentantite (the arsenical isomorph of tetrahedrite), the other of blebs of tetrahedrite in stannite. The only other possible instance of such intergrowths known to the author is the record of "pseudoeutectic" intergrowths of tetrahedrite with chalcopyrite and with bornite in a silver pitchblende ore from the Great Bear Lake district of Canada (Furnival,1939).Some interest attaches, therefore, to the two occurrences described below of tetrahedrite showing ex-solution relationship, in one instance with chalcopyrite, and in the other with bornite.TETRAHEDRITE-CHALCOPYRITEAn intimate intergrowth of tetrahedrite and chalcopy-rite, apparently the product of unmixing of a solid solution of...

Jan 1, 1946

By C R. Sundberg

Despite nearly a half-century of continuous production, the low-grade iron ore (taconite) deposits of North America remain economically competitive sources of raw materials for the domestic steel industry. The continued viability of these mature integrated mining-concentrationagglomeration complexes requires highly efficient utilisation of assets, especially the mineral resource. At Cleveland-CliffsÆ five North American managed operations, enhanced ore characterisation techniques are playing a critical role in their continued success. Due to the low-grade nature and complex mineralogical composition of these deposits, ore characterisation cannot solely rely on assay grades. Historically, taconite ore characterisation has augmented assay grades with bench-scale concentration tests to quantify recoverable mineral. The economic necessity for improvements in mill efficiencies and final product quality has mandated significantly greater knowledge of ore-related impacts. Cliffs Technology Center has met this challenge by developing a variety of novel iron ore characterisation techniques. The applications developed include both in situ and laboratory procedures, plus unconventional data integration methods uniquely suited for these deposits. This paper details the evolution of these novel ore characterisation techniques and their application to each phase of the operation: mining-concentrating-and pelletising. The improved ore characterisation techniques have contributed to successes at individual Cleveland-Cliffs managed operations including mineral recoveries exceeding 95 per cent and productivity increases exceeding ten per cent while consistently achieving customer product quality objectives.

Jan 1, 2002

By T Kon, K Ohno

Slag foaming is an important control item in the process of refining molten steel. This study aims to investigate the factors controlling slag foaming by observing the bubble formation behaviour resulting from the chemical reaction between iron oxide and Fe-C alloy in the slag. In this study, 0.06 g of Fe- C alloy was introduced at the bottom of a BN crucible, and 6.0 g of slag (SiO2:CaO:Fe2O3 = 40:40:30) was placed on top of it. The crucible was positioned inside an infrared image heating furnace, where the temperature was rapidly raised to 1370°C at a rate of 1000°C/min in a nitrogen stream, and then held at that temperature for a predetermined time before rapid cooling. Following rapid cooling, the internal structure of the sample was examined using a high-resolution X-ray CT device. The spherical equivalent volume was calculated based on the number of observed bubbles and their equivalent circle diameter. Additionally, the relationship between the volume ratio of small bubbles in the slag volume and the distance from the bottom of the crucible was determined, along with the calculation of bubble density and volume ratio. Under various experimental conditions, numerous bubbles with equivalent circular diameters ranging from 200 to 300 μm were consistently observed. The density and volume fraction of bubbles with circular equivalent diameters between 200 and 500 μm showed a tendency to increase as the distance from the bottom of the crucible increased. Bubbles with equivalent circular diameters of 500 μm or more consistently exhibited lower bubble densities, regardless of their height within the crucible. The formation of larger bubbles is attributed to a decrease in iron oxide concentration within the slag as the reaction progresses. However, this is believed to be due to their higher buoyancy, resulting in shorter residence times within the slag and a reduction in the number of encapsulated bubbles.

Aug 21, 2024

By D Kent, J Kirkpatrick

The mining industry has long wanted a single communication back bone to cover the majority of their requirements underground. The convergence of communication technologies in the office/surface environment has been identified by the mining industry as a means to achieve their long-standing goal. In particular use of Internet Protocol (IP) systems are seen as proving a basis for a mineÆs communication infrastructure. This paper presents the development philosophy and work undertaken by Inco Limited in Canada, as well as the implications of this on suppliers to enable the technology to be mine worthy and readily available.

Jan 1, 2005

By Richmond AJ, Allan J

The use of long-hole in-seam drilling techniques for seam gas drainage ahead of mining was introduced to the Australian coal industry by ACIRL in mid-1981. ACIRL's research program has involved the development and demonstration of drilling and borehole survey technology in addition to evaluating the gas drainage potential of long-hole in- seam boreholes. This paper presents the results of the long-hole drilling carried out to date in the Illawarra District of the New South Wales coal fields. Drilling experience in relation to both vertical and horizontal directional control of the drill string, drill performance and borehole survey techniques are discussed. In addition, results of gas drainage effected by the long boreholes are presented. Future potential and requirements for further development of this technology are Reviewed.

Jan 1, 1982