Search Documents

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

By Fraser CJ

Stability control plays a prominent part in the planning and execution of coal winning in the deep open cuts in the Latrobe Valley operated by the State Electricity Commission of Victoria (SECV). Different stability mechanisms affect the individual overburden and coal faces. These are the classical rotational slip in overburden and the three-dimensional tetra- hedral wedge or planar block slip in the coal faces. The stability of the overall batters is affected by the so-called "block sliding" mechanism, which is unique in Australian open cuts. The basal stability of the open cuts is affected by pressure from water in confined aquifers underlying the coal being excavated. This paper describes each of these mechanisms and the current monitoring and con- trol techniques practised by the SECV.

Jan 1, 1982

The central thickened discharge system of tailings disposal takes advantage of the natural beach slope formed by sub-aerially discharged tailings, and the non-segregating properties of thickened tailings, to create a homogeneous conical stack. The need for containing embankments can be largely avoided leading to capital and operating cost savings. Methods for estimating beach slopes and tailings density, essential parameters for the design of such a system, are described. Case histories from three mining operations are used to illustrate the application of the technique, There are also seen to be potential advantages in the areas of water management, seepage, and rehabilitation. Laboratory and in-situ testing enable parameters to be determined.

Jan 1, 1991

The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the excavation can be subjected and sustain damage. Though each specific rock mass occurrence is unique yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and the blasting of small-scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study.

Jan 1, 2003

By Watsford R. M S, Hutton R

Following the delineation of significant extra ore reserves during 1990, the decision was made to expand production from 350,000 tonnes of run of mine ore per year to initially 600,000 tonnes increasing to 750,000 tonnes per year. The existing plant consists of a conventional three stage crushing plant followed by a heavy medium separation plant that produces a product prior to grinding. Grinding is conducted in three stages of ball mill in series. Alternatives examined for expanding production included: aò SAG mill - ball mill circuit replacing the secondary and tertiary stages of crushing, the heavy medium plant and the existing ball mills; and, upgrading of the existing circuit configuration.

Jan 1, 1991

Large Off Highway Trucks operated in this country are generally of Diesel Electric Drive, this system tends to employ the familiar Electric Wheel. A number of fleets now employ the Traction Motor System as an alternative. An investigation is made of the operation of two such fleets. A brief description is given defining the components and their basic functions in each system. Available life history is presented and system reliability, maintainability and operator reaction is examined. Trlmnnnr rpm rn~r In the past large Off Highway Trucks operated in this country, that is those greater than say 120 tons, have tended to be driven by a Diesel Electric traction system. Although manufacturers are now offering mechanical or mechanical/hydraulic drives in the larger machines comments will be restricted to examining the Diesel Electric System. Since commencing operations in the mid 1960 period Hamersley Iron has made use of the diesel electric drive system using the familiar Electric Wheel. A departure was made at Tom Price with the purchase of the Wabco 3200 Series Trucks. These 235 ton capacity units employed a dual rear axle system with externally mounted motors. In 1976 a

Jan 1, 1982

By Snowdowne J. B H

Rand Mines, Limited, located in Johannesburg, Republic of South Africa has recently completed feasibility studies which have lead to the initiation of two major coal strip mining ventures. A minicomputer based mine planning system was developed to perform the feasibility studies. The broad approach of this system is to utilise inter.-actively the specialist skills and interpretative abilities of mining engineers and geologists. This paper reports briefly on the outline of the system and at greater length upon certain aspects of its use.

Jan 1, 1977

By Mazandarani M, Chabot L, Vichion K

Pitch-steering models have been developed for discretely advanced mining machines (such as heading machines and coal shearers) using small-angle geometry and there are illustrative examples of simulator predicted performance. Although simple linear models result from the analysis of open-based machines, sledge mounted machines require execution of a Linear Programming energy minimisation to determine the attitude of the machine base at each advance over the previously cut floor steps. An analytical approach is based on elastic beam concepts developed for such applications as longwall face conveyors, caterpillar tracked machines such as continuous miners and longhole drills. Simulation results for longhole drills show the expected performance of an automatic guidance system and the destabilizing effects of sensing deviation too far behind the drill bit. Certain drill bit boundary conditions are expected to assist TBM. steering studies in three dimensions.There is a real role in mining machine steering for the mathematical models used in flight simulators.

Jan 1, 1991

By Dunne R. C

Column flotation is receiving increased interest from both an industrial and research perspective in Australia. The traditional overseas application as a molybdenum cleaning cell is being expanded and a number of new applications as cleaners, scavengers and roughers are emerging in Australia. The success of column flotation has hinged on the new understanding developing from the work of Finch- and coworkers at McGill University, Canada, particularly in relation to scale-up parameters and model development. The aspiring column flotation user in Australia now a has wealth of experience to draw on when deciding on the correct procedure to follow during the process evaluation and plant installation stages of development. However, some aspects relating to column design, such as aeration mechanisms, require careful evaluation.

Jan 1, 1987

By B Delaney

For worker safety, mining companies are required to stop production and inspect hoist ropes. Visual inspection is generally done daily and EM inspection occurs every three to four months. During visual inspection, rope speed is generally reduced so an inspector can look for problems. In EM testing the LMA and LF traces are printed on a paper strip chart and a skilled operator interprets these traces. Mining companies only find large defects during visual inspection and are sometimes concerned about the content of EM trace information. This paper will present research outcomes that show how muck can be hoisted while performing a complete visual rope inspection at full speed. Other research results will show that digital signal processing can increase the amount of information available to the EM rope inspector. The research was funded by Inco, C-CORE, three AMIRA International sponsors and six sponsors from the Canadian Deep Mining Research Consortium (DMRC). The research will be commercialised in 2005.

Jan 1, 2005

This paper documents the relationship between material handling and processing costs compared to blasting cost. The old adage, 'The cheapest crushing is done in the pit', appears accurate in this case study. Comparison of the accumulated cost of powder, selected wear materials and electricity, indicate a strong, inverse correlation with powder factor (lbs powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone. Measurable, overall costs decline while shovel and crusher productivity rise by about five per cent when powder factor rises by 15 per cent. These trends were previously masked by the effects of weather, ore grade fluctuations and accounting practices.

Jan 1, 1995

By Smith IEM

Some samples from arc-type volcanic suites collected in northern New Zealand and southeastern Papua New Guinea show rare earth element (REE) and Y abundances which are enriched relative to the those typical of their respective associations. This enrichment appears to be the result of an alteration process which selectively mobilises the REE and re-precipitates them as REE-bearing minerals in veins and interstitial patches. The alteration is on a micron scale and is not detected in routine petrographic examination. The spectre of REE mobility in young apparently fresh rocks is important to igneous geochemists who use REE abundances to constrain petrogenetic models and may also be important because it indicates the operation of a natural REE enrichment process which could operate in the formation of economic REE deposits.

Jan 1, 1990

The problems arising in the excavation of hard rocks with the use of mechanical tools consist chiefly in a slow advance rate accompanied by an intensive wear due to the toughness and abrasiveness of the rock. In order to allow the further extension of mechanical excavation beyond the limits of the presently available technology, the assistance of waterjet aiming at improving the performance of the equipment while reducing the wear rate of the tools, has been recognised as one of the most interesting technical solutions. The paper illustrates the improvement of the performance of both disk cutters and picks obtained with the waterjet assistance at the Waterjet Laboratory of the University of Cagliari on a medium-hard rock.

Dec 6, 2010

By Fry P. R

Dragline operations have played a major and successful role in coal mining around the world for more than 30 years. Because of this long history, many of the operating draglines are reaching an age where maintenance and downtime costs are prohibitive, and decisions need to be made to either replace or refurbish them.In the current economic climate, refurbishment is a popular choice and this usually involves major structural repairs above and below the roller circle, together with replacement of the roller circle components. Often, the dragline tub is also replaced by a completely new one.

Jan 1, 1992

By N J. Beukes, J Gutzmer, C Reinke, M Bau

In this study the light sparse phase search (SPL_Lt) mode on the Mineral Liberation Analyser (MLA) was successfully used to identify and quantify the abundance of rare earth element (REE) phosphates in Precambrian iron formations. Monazite (light REE phosphate) and xenotime (Y and heavy REE phosphate) are identified and data from the MLA combined with the mineral chemistry of the two minerals are used to calculate and model the expected REE concentration and distribution in these two REE phosphates. The REE phosphates account for up to 31 per cent of the REEs in the banded iron formations (BIFs) and excellent correspondence is observed between the modelled REE patterns and the whole rock geochemical data available for the same samples. Except for quantifying the mineral weights, the sparse phase search also allows for the localisation of REE phosphate grains and the observation of their association with other minerals using backscatter electron (BSE) imaging. These observations are used to conclude that the REE phosphates were most likely of diagenetic origin, with REEs and phosphate remobilised from primary chemical precipitates. It is demonstrated that automated mineralogical techniques can be used to qualitatively and quantitatively describe the influence of a rockÆs trace mineralogy on its geochemistry.

Jan 1, 2008

Difficult ground conditions in the area planned for placement of vent rises to the surface at the Porgera Goldmine led engineers directing the project to chose blind shaft boring methods of shaft construction from the available alternatives. Zeni Drilling Pty Ltd was first contracted in 1988 to install a group of three closely-spaced, steel lined shafts. The success of these led to an order for a fourth hole in the same group followed by two more, less than a kilometre. away, under a separate contract in 1992. All of the shafts were completed on.schedule to within one day. The only significant difficulty arose during commencement of the last shaft when the strata collapsed trapping the drilling tools and jeopardising the stability of the surface collar pad. The situation was corrected by innovative lining techniques and the project went on to finish on schedule. This paper discusses the application of various technologies associated with the project including aspects of geotechnical input, drilling fluid chemistry, mining engineering and logistics.

Jan 1, 1993

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

By M Scoble, W S. Dunbar

This paper reviews methods for grade estimation in short-term mine planning for block caving. Two particular tools are used: Ordinary Kriging and Simple Kriging with moving averages. It is also considered the influence of draw characteristics on the grade estimation process. Reference is made to mine case study data and analysis. These demonstrate that operational grade estimation is not a trivial process. It must take into consideration: the grade variability (in terms of ore and dilution), sampling interval, geological and geotechnical characteristics, geometrical layout and draw characteristics. Significant improvements appear possible in short-term planning if variogram analysis, as well as kriging methodologies, are introduced into the operational grade estimation process.

Jan 1, 2000

By Wilson PH

A research programme sponsored through the Australian Mineral Industries Research Association investigated two aspects of mine aerodynamics on model scale. These were aero- dynamic losses in (a) shaft/airway intersections and (b) losses created by mine cages moving in a combined haulage/ventilation shaft. The shaft/airway intersections studied included base and intermediate levels for both upcast and downcast. shafts, with one to four rectangular airways intersecting a circular shaft. Changes in intersection geometry were limited to the installation of 45¦ conical brow cutoffs of varying size and the addition of simple flow control devices. The relative air- flows between the airways and the downstream shaft were varied over a range employed in Australian mining practice. In general, experiments revealed that a small brow cutoff was significantly better than none at all, and a simple device such as a cone can reduce losses and improve flow stability at an intersection. The mine cage studies determined the effect on aerodynamic loss of cage area blockage, height/length ratio, openings in cage walls and surface roughness due to external structural members. The results show that in a combined haul- age/ventilation shaft, when the relative air

Jan 1, 1978

By Hussey K. J, Morrison R. S

Recent mapping (1989-1992) by the Northern Territory Geological Survey in the Tennant Creek 1:250 000 map sheet area has resulted in substantial revision of the lithostratigraphy of the Tennant Creek Block (Donnellan, Hussey, and Morrison, in press). Briefly, the former Warramunga Group (Dunnet and Harding, 1967; Dodson and Gardener, 1978) is divided into the Warramunga Formation, and an overlying less deformed volcano-sedimentary succession, the Flynn Subgroup. The latter is conformably overlain by the Tomkinson Creek Subgroup of the Tomkinson Creek province in the north of the Tennant Creek Inlier. These two Subgroups constitute the Churchills Head Group which is essentially equivalent to the Hatches Creek Group of the Davenport province to the south of the Inlier.

Jan 1, 1994