Search Documents

By Lawson F

Arsenic-containing waste was dissolved into molten slags and the leaching behaviour of the quenched arsenic-doped slags (containing up to 2.3 wt per cent arsenic) was ascertained to evaluate the potential of this method as a means for arsenic disposal. The leaching behaviour was evaluated using acetic and sulphuric/nitric acid based solutions.From short-term (18 hour) leach tests, the amounts of arsenic in the leach solutions were found generally to decrease with an increase in the Fe(III)/Fe(total) ratio of the slag or an increase in pH of the leach solution. The amount of arsenic in solution increased with an increase in the slag basicity, the slag arsenic concentration or the surface area of the slag exposed to the leach solution. From longer term leach tests (up to 40 weeks) in the pH range 5 to 8, the arsenic remaining in the leach solution was believed to be controlled by sorption processes. The sorbent was an iron oxide-rich material which had the capacity to lower the arsenic concentration in the leach bottles to well below 1 ppm in some cases. At a leach solution pH over 9, the arsenic concentration in the solution increased with time, although the rate of solubilisation was much slower due to the high pH.Slags have the potential to stabilise arsenic and prevent it entering the environment provided attention is paid to the slag chemical composition and oxygen potential.

Jan 1, 1996

By S Grano, J Ralston

Selective oxidation of minerals was used in this study to separate by flotation the copper sulphide minerals of chalcocite, covellite and chalcopyrite from the arsenic copper sulphide minerals of enargite and tennantite. It was found that a satisfactory separation of these minerals was only possible after selective oxidation of their surfaces in slightly acidic pH conditions, or after oxidation and selective dissolution of the surface oxidation products with a complexant in basic pH conditions.

Jan 1, 2000

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S Thomas, E Grimsey

Mining education in Australia has undergone another cyclical downturn over the past five years and several departments have been discontinued while others are still teetering on the brink of destruction. During this downturn Curtin UniversityÆs WA School of Mines (WASM) has managed to stay alive and well, but this has not been by accident. This paper outlines some of the strategies and experiences that have kept WASM in a strong position and offers hope to other departments and schools elsewhere that are still experiencing difficulty. This paper is also directed at all mining departments and schools that are certainly going to see it all happen again after the next mining boom turns to bust.

Jan 1, 2004

By J R. Robinson

Prior to mine development, exploration drilling within the Luise Caldera on Niolam Island encountered gold mineralisation to the northwest of the main Minifie and Lienetz orebodies. This mineralisation was referred to as the Kapit orebody, and ten diamond drill holes were subsequently completed over the area to investigate its economic potential. Several significant mineralised intercepts were returned. These were interpreted using the orebody model developed for Lihir at that time which invoked a strong horizontal control to mineralisation. Additional consideration was given to the elevated geothermal temperatures encountered, the proximity of the mineralisation to the ocean, and its perceived depth below sea level, resulting in the Kapit area being given a low priority for follow up investigation. As a result, no further work was completed over Kapit until recently. The Kapit orebody was the target of an intense diamond drilling programme during 2002/2003. Data from this latest round of drilling has significantly improved understanding of the mineralisation and associated geology. The significant orebody now delineated at Kapit substantially differs from past interpretations, and the latest data has upgraded its economic potential. A resource estimate and other critical studies completed in 2003 enabled an updated reserve statement to be issued in February 2004 including the Kapit mineralisation for the first time. Total Probable Reserves at Kapit stand at 25.2 million tonnes (Mt) at 5.28 grams of gold per tonne (g Au/t), for a total of 4.3 million ounces (Moz) of contained gold.

Jan 1, 2004

By A M. Wala, H W. Wu

A research project incorporating a number of mine site exercises to reduce the effects of fire incidents and possible consequent health and safety hazards has been undertaken focused on the application of mine fire simulation software packages for contaminate tracing and fire modelling in coal and metalliferous mines. This paper examines aspects of introduction of inert gases to underground workings to aid recovery of a mine following a fire. Broad conclusions from work undertaken at individual Australian coal mines are discussed as examples. The effort is built around the introduction of the fire simulation computer program æVentgraphÆ to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Case studies have been developed to examine usage of inertisation units and particularly application of the GAG jet engine unit. One example has focused on selection of the best surface portal location for placement of the GAG for most efficient suppression of a fire. A second has examined a situation with significant seam gas being emitted on the face. This has shown that under certain face dip angles stopping the mine surface fan to reduce dilution of GAG exhaust gases will cause reversal of face air and consequent mine explosion as gas laden air is drawn across a fire. A third examines inertisation and dilution issues in mains headings. mains headings present a complex ventilation network with often numerous parallel headings, hundreds of cut-throughs and a variety of ventilation control devices. In such a complex system (with additional interference from a fire), maintaining control of the movement of inert gas is more difficult than elsewhere in the mine. Some illustrations of this issue are given.

Jan 1, 2005

By J Wu

Swirl Flow Technology (SFT), a novel approach for agitation in large industrial slurry tanks, was jointly developed and patented by CSIRO and Queensland Alumina Ltd (QAL). Currently, SFT is used in 16 alumina precipitation tanks at QAL, with the first installation in January 1997. This paper provides insight to the underlying fluid dynamics, which were investigated through pilot-scale experiments. A key finding was that SFT produces tank wall velocities approximately four times that of conventional draft tube agitator systems for the same power input, whilst for solids suspension, much less power is needed. SFT is energy efficient and practical in scaling suppression as demonstrated by the full-scale experience at QAL.

Aug 8, 2011

Over the last 15 years working in the mining, construction and extractive industries, one of the areas that has always concerned and at the same time drawn the author to it is the application of drilling and blasting in the underground development mining and civil construction tunnelling fields. In that time, the author has come across many drives and tunnels that are larger than design or badly damaged in the perimeter or both. When the question is asked as to why this is the case, the reply is generally æthatÆs the way it is and always has beenÆ. Sometimes it is blamed on bad ground, bad drilling, bad explosives, bad initiation or just plain bad. Most operators build a dilution factor into development and tunneling costs as an acceptance of overbreak and similarly pattern bolt everything to overcome excessive perimeter damage. This paper will attempt to unravel some of the mysteries behind perimeter drilling and blasting in underground drives and tunnels and discuss methods to reduce overbreak and therefore reduce costly dilution and to minimise perimeter damage which in turn will allow more cost-effective ground support. It should not be assumed that better drilling and blasting alone would automatically allow an operation to reduce ground support. The operator must still æreadÆ the ground and its characteristics in order to ensure sufficient ground support is placed to allow the operation to progress safely. This paper will not go into the intricacies of bolting, meshing, shotcreting, concreting and other ground support, but it will use indicative costs for the primary areas of drilling, explosives, excavation and labor to show the magnitude of cost-efficiencies which can be obtained through improved drilling and blasting applications. Drill and blast remains the most flexible and cost-effective method of underground excavation as long as it is applied safely and effectively.

Jan 1, 1999

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

By M Hedley

Tracking plant and personnel in underground environments provides multiple potential benefits for a mine including increasing safety, better monitoring of production, traffic control, and in the future monitoring and control of autonomous vehicles. The main techniques for wireless tracking are to use radio frequency identification (RFID), signal strength based techniques, and time of arrival (TOA) based techniques. RFID does not provide continuous tracking and signal strength techniques have poor accuracy in the complex radio propagation environment present in mines. TOA based techniques are potentially the most accurate, but most current equipment does not realise the potential of the technique. CSIRO has been developing the wireless ad-hoc system for positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines. WASP has been licensed for sporting applications and has delivered encouraging results in early trials for a surface and an underground mining application. The system utilises a number of ‘anchor nodes’ that are placed at surveyed fixed locations within the mine, and tags attached to plant or personnel to be tracked. The system provides an ad hoc data communication network, thus wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging from 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of initial testing in an underground mine that shows that the system achieves high ranging accuracy, hence localisation accuracy.

Mar 21, 2011

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

The effects of detonation of downlines and downline-booster systems on lodse-poured charges of 94% porous prilled ammonium nitrate/6% fuel oil (AN/FO) were determined. Detonation stability was indicated by the initiation-failure pattern of detonating fuse witness lines located at intervals along the charge. Steel tubing was used as the confining medium. Charge diameters (d) varied between 2-21/32 and 8.1/8 in. and specific charge weights (w) of downlines between 4.0 and 93.2gr/ft. The axes of charge and downline were colinear. The minimum value of w required to cause initiation of AN/FO increased with d. When initiated by a downline only, the charge'underwentlowòorder detonation. When downline-booster systems are used, the detonation wave in the downline cuts all equatorial planes in the charge before the detonation wave in the surrounding AN/FO. If the downline itself does not cause initiation, therefore, the explosive ahead of the main detonation wave is crushed, and hence desensitised, by the radially-expanding compression wave and gases generated by the downline. In a given equatorial plane, the fraction gftharge undergoing detonation decreases with an increase in the booster-plane distance. The longitudinal limit of nation increases significantly with d, but surprisingly little with a decrease in w. In the presence of a downline, the blasting performance of AN/FO charged _

Jan 1, 1970

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

By Riley S. J

Ranger Uranium Mine is located within the Alligator Rivers Region of the Northern Territory of Australia and surrounded by the World Heritage listed Kakadu National Park (Figure 1). The mining operation is currently producing about 1500 tonnes of uranium oxide annually, as well as considerable volumes of waste rock, low grade ore and tailings. The rehabilitation of the project should ensure that the radioactive mill tailings and other contaminants remain contained for at least 200 years, as required by the existing guidelines (Commonwealth of Australia, 1987). The present uranium mining operation is regulated by the Northern Territory Department of Mines and Energy who must refer to the Environmental Requirements when considering regulatory options. These Environmental Requirements were agreed by the

Jan 1, 1994

By Rolfe PR, Ellis BA, Clements RJ

Associated Minerals Consolidated Limited (AMC) is constructing a 112,500 tonne/yr synthetic rutile plant at Narngulu, near Geraldton in Western Australia. Design of the plant is based on the technology developed by AMC and utilised in its two existing plants at Capel in Western Australia. Ilmenite Feedstock for the plant will be sourced from AMC's mine at Eneabba and coal obtained from the Collie deposits. The plant is scheduled to come on stream in the second quarter of calendar 1987. The rationale of the decision to construct the Narngulu plant is examined against the background of the world market for high-Ti02 content feedstocks. Also provided is a detailed description of the plant and an examination of the technology used in process Design.

Jan 1, 1986

By Hatherly P, Luo X, Balusu R, Gale W

Ongoing, collaborative research between CSIRO's Exploration and Mining and Strata Control Technology has resulted in a better understanding of rock failure mechanisms around longwall extraction. Failure has occurred further ahead of the retreating face than predicted by conventional longwall geomechanics theory. In some cases significant failure has been detected several hundred metres ahead of the face position with demonstrated influences of minor geological discontinuities. Shear, rather than tensile failure has been the predominant failure mechanism in the environments monitored. Validating technologies of microseismic monitoring and new face monitoring techniques have assisted the development of predictive 2D computational modelling tools. The demonstrated 3D consequences of failure has assisted in the ongoing direction of the project to further investigate these effects.

Jan 1, 1998

Current attitudes by exploration companies towards working on another party's exploration permit or equivalent vary widely. That this is so is due to the virtual absence, on the one hand, of anything in the mining legislation in any jurisdiction that establishes what are the exclusive rights to explore, as opposed to apply for a mining tenement, that the grant of such an authority conveys on the holder, and on the other hand, of any code of ethics or set of guidelines to proper practise. By contrast, in most states and territories, if not all, it is an offence to enter onto a mining tenement, other than to cross it, without the consent of the holder, although until recently most field personnel would have been unaware of this and most explorers would have transgressed at one time or another. A similar vacuum exists where aerial surveys are concerned. There are in fact no guidelines. It has always been assumed that a party wishing to carry out such a survey was free to do so, without even an obligation to notify the holders of any tenements or permits in the area to be surveyed, let alone make available to them any data from the survey. Concepts of 'geophysical trespass' now being tested in the US also raise the possibility that data won from adjoining ground using geophysical techniques may be privileged. Attitudes now appear to be changing. In the absence of legislation or any code of practise, what does the industry regard as ethical behaviour? Do we need to define the rights and obligations of various parties more clearly, and if so, what should they be and to what extent will it be necessary to confirm them by legislation as opposed to adopting a code of practise? Will the existence of such a code in fact improve corporate practise?

Jan 1, 1995

Coal losses and dilution are among a coal mine operators everyday problems. These losses and unwelcome additions are generated primar- ily by the stripping operation and secondly by the coal mining opera- tion. Losses in yield due to preparation plant efficiency are a separate issue although they may be related to the coal mining operation. The losses and dilution can be traced to the following operations: (A) Overburden or Interburden Removal (1) Removal of coal edge by blasting operations. (2) Removal of top of seam by drilling/blasting. (3) Removal of top of seam by stripping equipment. (4) Removal of coal edges by stripping equipment. (5) Dilution due to stripping equipment. (B) Coal Mining (for the case where seams are ripped rather than shot) (1) Coal rib losses. (2) Coal rib dilution. (3) Coal left in floor. (4) Coal left in fault areas. (5) Floor material picked up whilst loading. (6) Spoil material picked up. (7) Spoil material from poor surface clean up. (8) Top of coal losses from final clean up. (9) Dilution from ripping too deep, i.e. into floor below seam. (10) Dilution from interseam parting. The losses apply to both the single seam and multi seam oper- ations although they are more pronounced in the multi seam mines than in a single seam mine due to the position of the coal which is lost. For example in the multi seam case the top seam coal edge loss is final. There is little chance of recovery with the subsequent pass even if the extra rehandle is done. However conversely the lower seam is relatively easy to locate as it has nowhere to go being contained by the lowwall bench.

Jan 1, 1988

By Chung S

The problems associated with equating calculated and measured properties of explosives with blast results are examined. The results from six full-scale test blasts in a limestone quarry are described. The purpose of the full-scale trial was two-fold, i) assess the role of varying aluminum levels (10% maximum) in a given explosive in terms of blasting performance, and, ii) find correlation between calculated, as well as measured properties of explosives and the resulting blasting performance. Each blast consisted of 36 holes, initiated with short period detonators in a staggered 3-row 2.4 m x 2.7 m (burden x spacing) pattern. Each 75 mm diameter borehole with no subgrade contained on the average 22 kg of 65 mm diameter cartridged explosive. The bench height was 6.3 m, with an average collpr of 1.2 m. The calculated and mgasured properties of explosive included, strength, detonation and explosion pressure, VOD, plate-dent depth, underwater bubble and shock energy, and the total energy efficiency. Each blast was instrumented to measure detonation velocity, initiation sequence, muck pile motion by means of high-speed photography and blasting vibrations. The post-blast measurements included photogrammetric survey of muck pile for size distribution on surface, muck pile profile, as well as the extent of backbreak. The results showed that the overall blasting performance of the explosive in question was nearly commensurate with the level of aluminum in the explosive, and there was excellent correlation between the underwater test properties and the blast results. The study also exemplified the need for more extensive post-blast analysis than is usual practice, for quantitative assessment of blasting performance of explosives and providing the necessary data-base for calibration of blasting models.

Jan 1, 1990

By S Versace, D Arnott, D Bojcevs, A Shaw

The George Fisher deposit is a significant sediment hosted silver-leadzinc resource located 2 km north of the Hilton Mine in NW Queensland. The George Fisher feasibility project involved the completion of underground and surface drilling programs to delineate Measured and Indicated Resource which could be converted to an Ore Reserve through mining and commercial studies. The geological information which was collected and used for the feasibility study included a major program of diamond drilling, predominantly from underground sites, but with some drilling also completed from surface. All drillcore was geologically and geotechnically logged, sampled and assayed. Data was also collected from underground cross-cut and drive development which was mapped for rocktype, ore distribution, structure and geotechnical condition. This new geological data, generated during the Pre-Feasibility and Feasibility stages, was combined with results of all previous drilling campaigns in the George Fisher area to produce a comprehensive database on which geological modelling and Resource estimation could be based. To allow fast and accurate collection and utilisation of data from the drilling program, digital collection processes were used where possible. This resulted in rapid data entry into the project database, significantly enhanced data quality, 100 per cent data ownership within the project team and increased productivity levels. Processes used during the project data collection program are described, lessons learned are related and suggestions for ænext timeÆ are listed using the benefit of hindsight.

Jan 1, 1998