Search Documents

By K Kuganathan, Y Potvin

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: a minimum filling rate of 250 m3/h, a curing time of 28 days, and minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998

Before proceeding I wish to say that the excellent diagrams by which my paper is illustrated are the work of Mr. C. H. Barnes, Constructing Engineer of the Kalgurli Gold Mines Limited, and I am also much indebted to Mr. F. A. Moss, manager of the mine and for the privilege piIling information not previously made public.The limited time at my disposal has coolled to, curtail the scope of my paper to a few practices in ore treatment which are being worked on the Kalgurli Mine, but which I believe are of more than ordinary interest to thp~e Goncerned in modern treatment of gold ores. As an introduction to my subject it is, necessary that I should give a brief outline of the process by whiGh the gold is won from the complex sulpho-telluride ore of the Kalguili mine.My business is not to enter into any discussion as to the relative merits of the two rival sulpho-telluride ore treatment processes at work on the Kalgoorlie field, viz, the treatment of the unroasted ore after shining by solutions of bromocyanide, as against the treatment of the ore-after roasting by solutions of potassium or sodium cyanide either in filter presses or percolating sand vats. Even if reliable costs and percentages of extractions were obtainable in each case, it would not constitute an infallible basis of comparison, as the larger plants would necessarily have an advantage in cost per ton as against the small plants, and the other conditions obtaining are in many Cases dissimilar.

Jan 1, 1903

By T Bednarz

The present work proposes a distributed collaborative immersive virtual reality framework for prospective applications in the mining industry. A human-centered approach is described, with people being placed in the central position and surrounded by tasks that are to be carried out. Those tasks can be then achieved through synchronous or asynchronous communication, interactions using properly constructed user interfaces, virtual and/or augmented realities and computer vision. Several examples of such arrangements are presented. One of the applications facilitates an e-learning experience by providing a very familiar object – a book – as a target for users to interact with. Importantly, this system has the potential to provide an ‘enhanced’ teaching medium, as humans tend to remember events/situations better when they experience those events in person, when the immersive factor is involved. The immersive virtual reality environment enables a user to interact physically with various 3D objects and experience behaviours, which in turn reinforces the idea that doing leads to learning. This prototype system can be implemented as an efficient and cost effective e-learning and training platform for different engineering domains. At another level, the same technology can be used in the tele-operation of mining equipment for the future mine.

Nov 22, 2011

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By M Dean, M Nehring, P Knights, M S. Kizil

Integrated continuous mining techniques such as fully mobile in-pit crusher and conveyor (FMIPCC) systems offer inherent labour, energy and environmental benefits to deep pit metalliferous mines. However, before such systems become commonplace, a number of barriers must be overcome.This paper outlines a number of commonly perceived barriers to FMIPCC application, together with a number of suggested solutions. The paper advances a design approach for specifying FMIPCC systems for deep pit metalliferous applications. A novel FMIPCC configuration is advanced using a hydraulic excavator in backhoe configuration. Because of the requirement to minimise belt extensions, a mine planning approach is presented based on a series of parallel and radial belt conveyor moves.The FMIPCC system does not fully replace truck-shovel systems. In the proposed mine plan, sinking is undertaken with truck-shovel systems using a series of box cuts, whereas pit ‘widening’ activities are accomplished via the FMIPCC system. Because of inherent differences in mine sequencing, the net present value derived from the FMIPCC mine will differ markedly from that derived from traditional, nested-pit, truck-shovel mining approaches. Therefore, any comparison of the FMIPCC and truck-shovel approaches must take into account radically different mine planning approaches.CITATION:Dean, M, Knights, P, Kizil, M S and Nehring, M, 2015. Selection and planning of fully mobile in-pit crusher and conveyor systems for deep open pit metalliferous applications, in Proceedings Third International Future Mining Conference, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By D Reid

The engineering properties of soils and tailings often exhibit significant anisotropy. One area where this has been well documents is undrained shear strength. Materials sheared in directions close to the principal stress direction in situ, i.e. triaxial compression, typically exhibit higher undrained strengths than those sheared in other directions such as simple shear. Importantly, along the most common critical failure surfaces relevant to tailings stability, whether primarily through tailings or a critical foundation layer, saturated materials are generally much closer to the simple shear loading direction than triaxial compression. Therefore, testing undrained shear strength of tailings or foundation soils in triaxial compression is likely to result in overestimation of the relevant strengths for design. Although these issues have repeatedly documented in the geotechnical literature for over three decades, they are not appreciated sufficiently across our industry. In an attempt to address and highlight these issues, a review is carried out of historical reference to the importance of simple shear loading. Attention is then drawn to the techniques applied in three recent post-failure investigations, where simple shear testing was applied. Finally, some relevant laboratory test results from a recent project in which the author was involved are outlined.CITATION:Reid, D, 2018. Importance of the simple shear loading direction to the stability of tailings storage facilities, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 274–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

Tertiary laterite is extensively developed in the Darling Range area, but there is doubt that. the high relief areas along the Darling Scarp have been peneplaned. Three distinct laterite types are distinguished which are termed transported, introduced and residual laterites to avoid ambiguity. Transported laterites are recemented (primarily) lateritic materials and introduced laterites are chemical deposits of bog iron type. Residual laterites are formed in situ from the host material which can be either decomposed bedrock or detrital' clay, and the two varieties formed from these sources are termed residual A and residual B laterites. The genetic requirements for residual laterite formation are (1) host material, (2) porosity and permeability, (3) rainfall, (4) temperature, (5) relief and drainage, (6) vege- tation and (7) time. Previous theories on the origin of laterite appear to be inadequate and incompatible with field observations. Field investigations and drilling in the Darling Range area disclosed lenticular section and thickest laterite development on slopes and thin or oc- casionally no laterite development on crests. Lateritisation is considered a surface feature and the end product of the chemical weathering cycle. The relief and rain-water acting on a kaolinitic host material are con- sidered the major contributing factors in the

Jan 1, 1973

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011

By G Hart

As the iron ore/magnetite boom gains momentum, it is particularly important to question established past trends and explore the potential of alternative design options. Traditionally, ‘rule of thumb’ methods have been used to size dewatering equipment. Greater consideration needs to be given to technological advancements and specific throughput testing of each ore body type based on innovative developments.This paper will describe how an innovative approach resulted not only in significant savings in capital cost and site work hours but also delivered a truly optimised design for the thickener duty at Karara. Test work also played a crucial role and a comprehensive test work program on the ore samples showed the scale-up benefi ts of new technology in thickener designs. Working closely with the Karara team during the laboratory testing proved the old sizing theories for iron ore/magnetite processing have been superseded with the knowledge and results of the industry’s newest feedwell technology. Increased solids flux and rise rates in the testing process proved very successful, resulting in signifi cantly reduced thickener sizes and lower capital expense.Mechanical design considerations such as removal of underflow and pump access led to a preference for an above-ground thickener confi guration, and the economics of a completefabrication and installation package favoured steel construction for the thickener units.The ultimate choice of the bolted/fl anged tank methodology provides both economic and timely solutions for the site installation including reduced man power and quick and safe site-work. A benefits comparison between this design and other fabrication and installation procedures will also be analysed in the paper.

Jul 11, 2011

By H Han, d S. Hapugoda, L Lu

With the recent rapid development of Chinese steel industry, the world iron ore resources of good quality are depleting rapidly. As a result, iron ore deposits of lower quality have been or are being developed to meet the market demand and are becoming increasingly important to iron and steel companies. As concentrates have advantages of high Fe grade and less harmful impurities, they are ideal sweeteners to maintain sinter grade and quality when high proportions of low-grade ores are used in the sinter blends. However, due to their fine nature, addition of concentrates will inevitably increase the proportion of adhering fines and reduced the proportion of nucleus particles of the sinter blends, which can adversely affect the green bed permeability and sintering productivity. In the present study, lab scale sintering tests were carried out under the conditions similar to the sintering process to examine the effect of concentrates on the high temperature sintering characteristics of sinter blends and the structure and strength of the resultant sinter analogues.

Sep 18, 2023

By C Claassen, R Balusu

Computational fluid dynamics (CFD) models have been developed based upon field data collected from a longwall mine in New South Wales, Australia to study the behaviour of goaf gas flow in both active and sealed goaf areas. A base CFD model was built to represent the goaf situations when the active longwall retreats near the finish-off line. Results from the base model were calibrated and compared against field goaf gas monitoring data. The base model was then used to carry out parametric studies to investigate a number of operational scenarios and their impact on goaf gas behaviour. CFD modelling results indicate that the overall goaf gas flow pattern changes as the operating longwall retreats towards finish-off line. In all cases, oxygen penetration into the active goaf remains high, reaching 15 per cent or higher, even at some 800 m behind the longwall face.The modelling results also indicated that it would be difficult for early detection of an active goaf heating (on the maingate side) based upon CO readings in the return airflow, as the main stream of the gaseous product will be flowing into the sealed deep goafs in adjacent longwall (LW) panels. Monitoring points (such as tube bundles and bag sampling points) should be selected at deep seated seals along the active goaf so that abnormal CO or C2H6 readings can be picked up for early detection and location of potential heating spots; goaf inertisation can be better achieved by injecting inert gas such as nitrogen at deeper points (>200 m) behind the operating longwall; the injection of in-seam drainage methane into the goaf areas will only have a limited impact on goaf inertisation as much of the injected methane will migrate towards deep and higher parts of the goaf due to its buoyancy effect.

Sep 26, 2011

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By T Laing, M A. Abdalla, P Hagan

Open pit operators are facing a number of challenges in the area of blasting and blasting processes, such as wall control, quality of fragmentation, explosives consumption and vibration. Remaining financially viable is one of the most significant objectives for mining professionals as they work through the blasting challenges within the mining chain of processes. This objective is such a significant challenge, primarily due to the high consumption of materials and the direct consequences on the downstream processes in the mining work flow, including loading, hauling, crushing, milling and mineral concentration. This paper reviews and discusses a technique to achieve this objective, namely air-decking. The performance in a number of mines around the world is reviewed focusing on the economic contributions of air-deck blasting. Various scenarios are investigated and simulated, covering both conventional and air-deck blasting, using JKSimblast software. The scenarios explore a range of issues and found that optimum results could be achieved with a minimum amount of explosives. The results obtained from the simulations were verified with blasts at Rixs Creek Coal Mine, Australia. Based on the verification results the simulations were then modified to more accurately model the actual conditions and parameters on site and to ensure that the models derived meet the production and control requirements at the mine site. Ultimately, overall analysis and comparisons were applied to the outcomes of the conventional and air-decking blasts revealing a reduction in material consumption of around 25 per cent with consequential savings and up to a 30 per cent reduction in ground vibration.CITATION:Abdalla, M A, Laing, T and Hagan, P, 2012. The contribution of air-deck blasting to open pit mining economics, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 7-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By T W. C Stambolie

Longwall mining is a form of underground mining and the principal extraction method for underground coal mining in Australia. The method is used in the mining of both thermal and metallurgical coal. The primary market for thermal longwall mines is that of the export market where price is governed against the Newcastle Thermal Benchmark index (globalCOAL, 2016).Australia’s thermal coal export outlook is considered moderate due to slower demand from major importing countries, as well as slowing domestic production. However, ‘Australia is projected to increase its share of world thermal coal exports and become the world’s largest exporter over the medium term as lower prices, increased domestic use and infrastructure constraints limit growth from other key suppliers’ (Office of the Chief Economist (OCE), 2016, pp 25, 58). On the contrary, and as a result of current global coal price trends, the basic economic principles of underground longwall coal mining are heavily stressed. From a life-of-mine perspective, influencing return on investment is at its greatest during project evaluation and execution. Appropriate and realistic economic assessment is paramount to ensuring the right outcomes are achieved under the current economic challenges.CITATION:Stambolie, T W C, 2016. Thermal coal industry – is longwall mining currently a life-of-mine option in Australia?, in Proceedings Life-of-Mine 2016 Conference, pp 57–61 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Sparrow G. J

In a recently completed AMIRA project, 20 samples were searched for gold mineralisation using the automated location facility (ALF) for rare phases on a scanning electron microscope in the CSIRO Division of Mineral Products, Melbourne. The samples were submitted by mining companies in Australia, and Papua New Guinea, and included crushed ore samples, cyclone overflow and underflow products, a flotation concentrate, and 12 tailing samples. Their gold contents ranged from 600 to 0.2 g/t An. Native gold and gold minerals including a gold telluride, gold-silver tellurides, and a gold bismuth mineral, were located in the samples as free grains and associated with other minerals such as pyrite, magnetite, hematite, ankerite, copper sulphides, silicate minerals, and quartz. In the highest grade samples, both micron sized and 200 ¦m grains of gold were found with ALF. It would be difficult to locate such d wide size range of gold in a manual search. Gold mineralisation was located in the tailing samples assaying 0.4 g/t An and higher. In several tailing samples coarse grains of native gold over 40 p.m in size were located. One grain was estimated to have contributed 40 per cent of the gold in the sample. As well as locating gold mineralisation, the ALF examination resulted in the identification of uranium, mercury, and bismuth minerals in the samples. Knowledge of the distribution of these minerals in processing streams could be important in the operation of a concentrator.

Jan 1, 1992

By J V. Lawless

Two types of low sulphidation epithermal deposits that have different gangue mineralogies and ore shoot geometries are recognised. One has laterally near-continuous ore shoots over a significant vertical interval that consist of quartz, chalcedony, pyrite, minor base metal sulphides and adularia, with electrum. The other type of deposit has discrete near-vertical ore shoots of a lesser vertical extent, that consist of quartz, pyrite, base metal sulphides, sulphosalts, electrum and in their upper parts barite, which are enclosed in veins of earlier quartz. The gold mineralisation in both deposit types is considered to be a co-precipitate of pyrite, with that in the first type of deposit produced by prolonged boiling in an upflow of a hydrothermal system (Upflow Deposits); an example is Waihi in New Zealand. The other type is produced by mixing, a deep water primed for gold deposition by prior limited boiling, with an iron-bearing oxidised condensate of the steam released by the boiling, in an outflow of a hydrothermal system (Outflow Deposits); an example is Thames in New Zealand. Early recognition of these different types of deposits can be used to develop mineralisation models of predictive value on which to focus exploration drilling. Early recognition of an Upflow Deposit promotes an extensive program to delineate the extension of the main ore shoot. In contrast recognition of an Outflow Deposit requires a more intensive approach to find individual ore shoots which, although smaller than those found in Upflow Deposits, may be high-grade, particularly if there is earlier mineralisation present to act as a protore.

Jan 1, 1999

By Butler I. K, Nicholson P. M

There are four main types of base metal and gold mineralisation recognised in the central Pine Creek Geosyncline. These are stratiform, polymetallic veins, stockwork/concordant gold-quartz veins and unconformity related uranium-gold-platinoid mineralisation. The stratigraphy of the central Palaeoproterozoic Pine Creek Geosyncline has been simplified into three groups comprising the Batchelor, Frances Creek and Finniss River Groups in ascending order. Stratiform mineralisation occurs within the Frances Creek Group. The earliest mineralisation is found adjacent to circular faults ringing basement highs. Higher in the stratigraphy, stratiform mineralisation is often associated with zones of high compression in the vicinity of basement highs. A synsedimentary-diagenetic origin for stratiform mineralisation is proposed. Polymetallic vein mineralisation occurs within the Frances Creek and Finniss River Groups. Its composition changes systematically through the stratigraphy similar to the stratiform mineralisation. The mineralisation is structurally controlled and usually occurs in the vicinity of basement highs. Stockwork-concordant gold-quartz vein mineralisation is hosted by the upper Frances Creek and Finniss River Groups. It occurs within compressional zones and along the Pine Creek Structure corridor around, above and particularly between basement highs. Mineable reserves occur in thick continuous semi concordant quartz-sulphide veins and/or stockworks. Unconformity related uranium-gold-platinoid mineralisation shows a close spatial relationship with the Palaeoproterozoic/Mesoproterozoic unconformity. The mineralisation is localised by structures formed during Mesoproterozoic deposition and is commonly adjacent to Archaean basement or its remobilised equivalents. The type of mineralisation (stratifom/polymetallic vein) is a reflection of local stress regimes, structure and physio-chemical conditions. An initial phase of stratiform mineralisation is postulated to have occurred with the first significant marine transgression in a tensional regime. A second phase occurred later during a compressive regime. "Ihermochemical sulphate reduction of mineralising fluids by hydrocarbons is invoked as the precipitation mechanism for the polymetallic vein type of mineralisation. Hydrocarbon generation is postulated to have occurred within the Frances Creek Group, in many places contemporaneously with the movement of mineralising fluids and basin compression. Polymetallic veins formed from the interaction of mineralising fluids and hydrocarbons which were trapped in suitable structures. An abundant, continuing supply of hydrocarbons was necessary to form significant deposits. Where these conditions were not net, the mineralising fluids largely continued their ascent to the near surface environment to form stratiform deposits. The stockwork/concordant gold-quartz vein mineralisation is a later event and occurred during the relaxation of compressional defonnation after deposition of the 1-inniss River Group.

Jan 1, 1994

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By S Vink, A Wolhuter

Increasingly the community and government regulators are calling for æzero dischargeÆ mines. Some mining companies are beginning to explore ways in which they can transition to zero discharge. When striving to attain zero discharge, mines must consider multiple variables in addition to water quantity. These include climate regime, water quality and regional water budgets. This paper explores the drivers behind the concept of zero discharge mines and will use examples to illustrate the feasibility of attaining this goal.CITATION:Wolhuter, A and Vink, S, 2013. Is zero discharge a viable or useful concept in mine water management?, in Proceedings Water in Mining 2013 , pp 329-334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By A D. T Goode

Data Metallogenica (DM) is unique as a global mineral sample collection and deposit database with over 70 000 rock samples and a wide range of descriptive, photographic and measurement data. Subscribers have access to approximately four gigabytes of on-line data with many examples included on the public pages. DM commenced its life on the Pacific rim in 1971 and much recent growth has focused on countries of the Pacific margin, particularly Australia, Fiji, Chile, Indonesia and Peru. Approximately 600 separate deposits and mineral occurrences in this region are represented in DM. The sets of rock samples have been photographed at high resolution and included on the web site, together with unpublished descriptions, deposit cross-sections, bibliographies, field and mine photographs, petrology and reflectance mineralogy. Figures and abstracts from PhD theses are a new addition and the donation of proprietary databases by companies and individuals is an encouraging trend. DM increasingly is being viewed as an acceptable and important repository for æfragileÆ and irreplaceable personal and company data, it is also being recognised in its true light as a high level information system, not solely a collection of rock samples. Data Metallogenica is a not-for-profit venture of AMIRA International that requires self-funding from December 2004. Growth and development must be funded entirely out of subscription and sponsorship revenues because no government subsidy is provided. The Pacific rim is in the mainstream of mining and exploration activities worldwide and those involved have much to gain from a dynamically sustaining DM. The home page at www.datametallogenica.com contains much example data and details of subscription and membership rates.

Jan 1, 2004