Search Documents

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

The Lihir deposit in Papua New Guinea (PNG) contains an estimated mineable reserve of 454t (14.6M oz) of gold in refractory sulphide ore. The Lihir Joint Venture has submitted a proposal to the PNG Government to develop an open pit mine and to install a process plant and associated infrastructure facilities on Lihir Island. The proposed process plant will employ whole-ore pressure oxidation technology, has a design capacity of 2.825Mt/a of ore containing 7.20 sulphide sulphur, and is expected to average 19.3t/a (620,000 oz/a) in gold production during its first 12 years of operation.An extensive program of process development testwork and feasibility engineering was completed to establish the process plant design for the Lihir Project. Summary results of this test-work as well as key design criteria, the process flowsheet, and major equipment selected for the commercial plant are presented and discussed.

Jan 1, 1994

By H Thanasekaran, M J. Mankosa, J N. Kohmuench, G H. Luttrell

"Fluidised-bed flotation has been demonstrated over the last 16 years as an effective method for improving the flotation recovery of coarse particles. This technology has been successfully deployed into the industrial mineral sector with multiple installations within phosphate beneficiation plants and potash mills. Due to the minimal mineral surface expression required when utilising this technology, more recent studies have centred on the applicability of using this HydroFloat™ technology for the recovery of coarse sulfides and base metals. Multiple approaches have been investigated to determine the best means for implementing this novel coarse particle flotation system into both existing and new plant circuitry. These include the treatment of tailings to recover values that have been lost using conventional technologies and also the direct treatment of a coarse feed, either within the grinding circuit or by use of a separate split-feed flotation approach. Recent applications of the technology will be presented along with data generated from several test campaigns and ongoing research investigations. The benefits of properly applying this technology, such as reduced power consumption and increased mill capacity will be discussed.Citation:Kohmuench, J N, Thanasekaran, H, Mankosa, M J and Luttrell, G H, 2016. The Impact of Fluidised-bed Flotation for Treating Coarse Sulfides, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 105–112 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

By Cameron A

In recent years there have been significant developments in the tech- nology available for blast monitoring, analysis and simulation. Progress in these areas has been achieved through research conducted by explo- sives manufacturers and independent research groups from universities and mining companies. Miners are increasingly keen to exploit this tech- nology to help them design blasts which make optimum use of explo- sives to produce easily excavated muckpiles for the minimum possible cost. The art of blast design in the future will increasingly depend on an adequate understanding of the nature of the rock mass, the perfor- mance of explosives and the characteristics required of the muckpile to suit the chosen excavation machinery. Despite recent advances in blast simulation and the prediction of blasting performance, the best way to determine how a particular explosive will function relative to other explosives is to conduct properly designed and monitored field trials. This paper discusses recent work at Mount Thorley Colliery which demonstrates that field blasting trials can be monitored and analysed to provide quantitative data on the relative performance of bulk explosives. Techniques used in the trials included the sampling and analysis of explo- sives, insitu measurement of VOD, monitoring of near and far field vibra- tions, high speed and still photography and survey measurement of muckpiles. These techniques provided data for the analysis of throw, swell, fragmentation and burden movement together with data on the consistency and robustness of different explosive products. The blasting trials allowed both the shock and heave energy of various explosives to be observed in the field and led to the derivation of design rules for the use of differ- ent explosives at the mine.

Jan 1, 1988

By T Peters

The Kibali Gold Mine is currently comprised of several open pits, a 3.5 Mtpa underground mine and a 7.5 Mtpa processing plant. Development of the underground operation commenced in December 2012, with initial access established through twin surface declines, followed by the commencement of a blind sink 8 m diameter rock hoist shaft in March 2013. Stope production started in December 2014 with ore and waste trucked to surface. The 755 m deep blind shaft sink was completed in August 2015 together with the cutting and equipping of three main station levels. Two of these levels provide access for the establishment of the underground materials handling system as well as the main dewatering system for the mine. This paper covers the process of determining the optimal location of the Kibali hoisting shaft relative to project-specific critical factors, and then focuses on the design and implementation journey associated with the off-shaft development that essentially encompasses the Material Handling System (MHS) for the mine. The journey starts from the findings of the previous owners Feasibility Study (FS), a subsequent Optimised FS, followed by detailed engineering through to implementation. It was identified during implementation that a significant change in the designed off-shaft layout was required following detailed underground geotechnical and hydrogeological investigations. In addition, the paper provides details on the MHS performance since commissioning to steady state, and on key learnings relating to the overall project process.

Mar 29, 2023

The Melanesian Outer Arc, extending from. Papua New Guinea to Fiji, developed as a result of interaction between the Australian and Pacific plates throughout the Tertiary, and the following stages are recognized. ,a, Formation of island arc tholeites above a west facing subduction zone in the Lower Tertiary. fit Emplacement of mainly calcalkaline volcanics above an east facing subduction zone in the Upper Miocene and Pliocene. ontinued east facing subduction coupled with fragmentation of the arc from the Pliocene onward. Alkaline and Mg-rich volcanism occurred in addition to continued calcalkaline activity. Tre Upper Miocene and younger volcanism is into five arc segments on the basis of geographic position and nature of the magmatism. The calcalkaline Bismarck arc extending along northern New Britain and including small islands to the west. The alkaline Tabar to Feni arc, north of New Ireland. The Solomons arc, including Bougainville and the western part of the Solomon slands. Volcanism is largely _.alcalkaline, but Mg-rich varieties occur the Solomon Islands. roe New Hebrides arc, extending from the -astern Outer Islands of the Solomons through Vanuatu. Both calcalkaline and :alkaline volcanics are representeo. alkaline and calcalkaline Fiji arc.

Jan 1, 1987

By Just GD, Gillies ADS

The competitive coal market has required coal producers to put more effort into coal quality control. Successful quality control requires a good estimation of the in situ coal quality as well as a good estimation of the probable fluctuation of the in situ coal quality during production. Geostatistics offers a very promising way to meet this requirement. A geostatistical approach toward the coal quality control problem is presented. Two models, the prediction model and the conditional simulation model, have been developed for coal quality data from two large export coal mines in central Queensland, Australia. The mine planning and scheduling aspects based on this and other potential applications of the models are addressed.

Jan 1, 1990

By Boyd GL

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal rCCOvCrCd h\ hi'eh ss-all mining methods.

Jan 1, 1998

By D K. Miller, L W. Armstrong

In April 2006, Orica Quarry Services undertook an investigation to determine the likely vibration and frequency response of three water storage tanks to quarry blasting, immediately adjacent to the tanks. Of the three tanks that were studied, two are relatively tall with a æwineglassÆ shape; one is constructed of steel (4 ML storage capacity) while the other is constructed of concrete (2 ML storage capacity). The third is a ground-embedded concrete tank that is relatively squat and broad in shape (38 ML storage capacity). A vibration limit of 25 mm/s and an acceleration limit of 0.16 g were imposed on the tanks. However, this report shows that this acceleration limit, whilst having relevance to low frequency earthquake motions, is quite inappropriate for the high frequency blast vibrations that are typical in a quarry blasting environment. The investigation involved firing 11 single blastholes of known charge weights and distances from the tanks, and measuring the tank vibration response using blast monitors placed on and around each tank. Analysis of the data collected from the cement tanks showed resonant responses over a broad range of frequencies, with dominant and lesser responses in vertical and lateral motion recorded at 9.8 Hz, 12 Hz, 16.8 Hz, 17 Hz, 31.3 Hz and 38.1 Hz. Unfortunately, most of the data collected on the steel tank was corrupted by noise due to electrical sources and/or mechanical sources such as the water agitator inside the tank. Advanced Monte Carlo vibration models were then constructed using the single blasthole information. Knowing the resonant frequencies enabled the modelling of electronic delay sequences for the reduction of resonant vibrations. Ultimately programmable and accurate electronic delay detonators were deemed essential to allow blasting in relatively close proximity to the tanks while avoiding resonant frequencies. Three blast designs were modelled, ranging in maximum instantaneous charge (MIC) from 4 kg to 22 kg, and 60 holes to 160 holes. The modelling showed that two of the designs (using small charge weights) could be used no closer than 71 m from the storage tanks. This is based on a 90 per cent confidence level of achieving vibration levels within the 0.16 g acceleration limit, even though the velocity levels predicted to be generated at this distance were significantly less than the 25 mm/s limit. The third design incorporated larger charge weights and could be used for blasting at distances no closer than 220 m from the tanks. The present work, conducted in an operating quarry, demonstrates the usefulness of Monte Carlo waveform superposition techniques for the control and reduction of ground vibration (either velocity or acceleration) under restrictive environmental constraints. However, a discussion is also presented to demonstrate that it is somewhat restrictive to impose an acceleration limit based on the motion produced by low frequency earthquakes rather than the motion produced by high frequency blast vibrations.

Jan 1, 2007

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By T Peglas, A de Aboitiz

The Queensland Government, via the special purpose company vehicle û City North Infrastructure Pty Ltd û is currently developing BrisbaneÆs Airport Link underground toll road and Northern Busway (Windsor to Kedron).Airport Link is a predominantly underground toll road planned between BrisbaneÆs northern suburbs, the airport and the Brisbane Central Business District (CBD) frame. The Northern Busway forms part of BrisbaneÆs expanding busway network, sections of which will be jointly delivered with Airport Link. Airport Link will connect the North-South Bypass Tunnel, Inner City Bypass and local road network at Bowen Hills to the northern arterials of Gympie Road and Stafford Road at Kedron and Sandgate Road and the East-West Arterial in the cityÆs north-east. The Northern Busway is a two-lane, two-way bus-only roadway proposed to connect the existing Inner Northern Busway at Herston with Windsor, Lutwyche, Kedron, Chermside, Aspley and Bracken Ridge. Airport Link and Northern Busway (Windsor to Kedron) is one of the largest infrastructure projects planned in the first phase of the State GovernmentÆs South East Queensland Infrastructure Plan and Program. The paper will provide an overview of the projects, including a discussion on the technical and environmental aspects as well as the procurement of the Airport Link as a public private partnership.

Jan 1, 2008

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By M Zoorabadi, B Hebblewhite, S Saydam, W Timms

Based on the cubic law, the hydraulic aperture of rock discontinuities has the most significant effect on the hydraulic conductivity of jointed rocks. The hydraulic aperture of rock discontinuities is a stress-dependant parameter and reduces with increasing applied stress. Furthermore, the rock stress increases with increasing depth. Therefore, hydraulic aperture is a depth-dependant parameter. In this paper, new empirical equations are introduced to calculate the hydraulic aperture of rock discontinuities at different depths. These equations were developed on the basis of back analysis of compiled packer tests from different actual cases. They provide the capability to calculate range of variation and average hydraulic aperture when the orientation of discontinuity and field stress tensor are given. Furthermore, it is possible to calculate the hydraulic aperture of rock discontinuities when its value is given for another depth. A hydraulic aperture of 7.7?µm was calculated by this method, comparing well with a reported site value of 8.3?µm for rock discontinuities at the Stripa mine project at a depth of 385?m. These new equations can be used by analytical or numerical methods to estimate the hydraulic conductivity of jointed rocks.CITATION:Zoorabadi, M, Saydam, S, Timms, W and Hebblewhite, B, 2014. New empirical equations to estimate the hydraulic aperture of rock discontinuities at different depths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 375–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

Completing its historical role the opera tion of copper blast furnace of the Saganoseki Smelter was terminated in 1970, but it left some interesting data on metal lumps formed at the furnace bottom. Analysis disclosed the lumps to be speiss containing 100 to 10,000 g/t of Au and Ag and stratified to iron speiss and copper speiss. Solidifying temperatures of iron speiss and copper speiss being approximately 1,090¦C and 800¦C respectively, copper speiss precipitated at the lower side. The distribution coefficient of Au and Ag between matte and speiss (g/t Au(Ag) in matte / g/t Au(Ag) in speiss) is in the range of 1 x 10 2 to 2 x 10 ' and 1 x 10 1 to 5 respectively. The higher Cu % is in speiss, the-more An and Ag are distributed into speiss. Except for a few data, these results comfotm well to the range of distribution equilibria of Au and Ag in matte and speiss systems by Gerlach and Others.

Jan 1, 1980

By Eisele TC

Horizontal perforated-plate baffles were shown to improve the cleaning efficiency of a flotation column when processing coal from two sources. The baffles consisted of flat plates with holes large enough to avoid plugging problems, and they improved the washing efficiency by making the flow patterns in the column closely approach plug flow. Tests with varying amounts of baffle open area showed that the optimum was between 30 and 40 per cent open area, which effectively prevented backmixing without seriously reducing capacity. The baffled column had previously been tested under ideal conditions with good results (87 per cent pyrite rejection at 85 per cent combustiles recovery), and so the tests reported here were intentionally run with difficult-to-float coals to determine the benefits of baffling under adverse conditions. For an original coal feed containing 38 per cent ash and 3.23 per cent total sulphur, the baffled column could recover 84 per cent of the combustibles while rejecting 84 per cent of the ash and approximately 54 per cent of the pyritic sulphur. Without baffles, the column recovered 88 per cent of the combustibles while rejecting only 76 per cent of the ash and 45 per cent of the pyritic sulphur. Subsequent tests with a dye tracer showed that the baffles reduced entrainment by approximately a factor of five, while the recovery was reduced by only a few per cent. Overall, the loss of capacity due to the baffles was more than offset by the improvement in product quality.

Jan 1, 1993

By LaBrooy SR

A number of gold processing plants in Western Australia have nickel in their ores, leading to significant levels of nickel on their loaded carbon. The presence of nickel during leaching, adsorption and elution'may have detrimental effects on cyanide consumption, carbon inventory requirements, stripping costs, electrowinning efficiencies and may contaminate the gold bullion.This paper discusses the competitive adsorption of gold and nickel cyanides onto activated carbon and investigates changes in solution parameters that may improve gold adsorption and/or inhibit nickel adsorotion.

Jan 1, 1997

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

By Hunsaker R. D

The description, characteristics, advantages and application of a new bulk explosive for medium to large diameter dry blasthole conditions is described. A brief outline of the delivery system for the product is also included. This explosive has been designed to provide an alternative to ANFO, currently the most common bulk dry hole product available to the mining and quarrying industry. The selection of the optimum explosive for any blasting operation is of prime importance. It is a major factor contributing to the production of the desired results in terms of muckpile fragmentation, shape and diggability. The optimum explosive can be defined as the most cost-effective in producing satisfactory breakage and displacement of the material. ANFO satisfies this prerequisite for a significant proportion of dry hole applications. This unique, low density and low velocity of detonation explosive has been developed to provide the industry with a cost competitive alternative to ANFO. Typical loading or average inhole densities nominally range between 0.40 g/cc to 0.70 g/cc, depending on the application. Characteristics of this explosive allow for specific and common applications in open cut coal and metalliferous operations. These include ore/waste control operations, prestripping and presplitting applications, sites confronting cap rock problems, and large hole diameter quarries.

Jan 1, 1995

The Nelson province was chosen as the prime area for rhenium sampling, based on its mineral associations. Sample preparation involved benefication by grinding and flotation A modification of published procedures for rhenium analysis was developed and the results compared with those obtained for molybdenum on the same samples using atomic absorption spectroscopy. The results of the analysis for both metals is discussed and the relationships between rhenium and the molybdenum mineralisa- tion of this region is commented on. A metal- 1ngenic province is defined for molybdenum and r'.ienium and the tectonic setting for this is discussed. Some consideration has been given to rhenium possibilities in Fiordland and the Coromandel Range.

Jan 1, 1980