Search Documents

By Cornell J. B

Scaling in Bayer Refineries is a natural consequence of the super-saturated liquors used in the process. The caustic liquor is supersaturated not only with alumina but also silica and calcia at various stages of the process. The basic scaling mechanisms are reviewed and examples of the two basic types, growth and settled scales, are given. Examples include gibbsite scales formed in the precipitators and silica scales formed in heat exchangers. The main factors affecting the rate of growth of growth scales are temperature and supersaturation and are highlighted using a silica scale example. For growth scales chemical cleaning rates can readily be predicted from kinetics and an example for a gibbsite scale is given. For settled scales the growth rate cannot be predicted and the hydrodynamics within the system have most effect. There is no simple method to predict the potential for chemical cleaning of settled scales; some of the relevant issues are discussed, in particular methods to identify the cementing phase in the scale. An example of design considerations for a scaling system, transport of slaked lime, is Given.

Jan 1, 1996

By Dunn J, Nguyen G, Graham J

A pyritic gold concentrate from the Golden Mile, Kalgoorlie, was roasted over a range of temperatures in a pilot scale fluid bed reactor. The calcines were subsequently cyanide leached. Mineralogical studies of the con- centrate, calcines and leached residues were also undertaken. Calcines produced at 500'C gave the poorest gold extractions and high cyanide consumptions. Gold recoveries of approximately 90 per cent were obtained from calcines produced at 550-600'C but higher roasting tempera- tures resulted in an increase in the residual gold content of the leached calcine. There is some evidence of flash smelting of the pyrite at the higher roasting temperatures and encapsulation of gold particles. Mineralogical examination of the calcines shows that the mechanism of oxidation is temperature dependent. At 500'C pyrite is directly oxidized to hematite with a concentric layered texture which appears to inhibit lixiviant access to enclosed gold particles. At higher temperatures the conversion sequence pyrite-pyrrhotite-hematite produces a spongy calcine which al- lows easier penetration by the leaching medium.

Jan 1, 1991

During underground mining, rock mass changes can occur as a function of the mining sequence and excavation processes. Mining-induced rock mass damage can occur due to redistribution of static stresses and the application of dynamic stresses from blasting and seismic activity. These rock mass changes can result in a degradation of strength of the bulk rock mass and the remaining rock surrounding existing excavations. Rock mass damage near existing excavations which lead to excavation-scale instabilities such as rock fall, excavation closure, or visible rock mass fracturing can detrimentally affect the safety and profitability of mining operations.The focus of the current work was the prediction and assessment of damage to mine infrastructure occurring in relation to the blasting of a sublevel open stope. The study case involved a 60kt stope located in a highly-competent rock mass at a large Australian sublevel open stoping mine. The mine infrastructure of interest for investigation included local stope access development, critical access and haulage development crossing a regional-scale fault, an explosives storage magazine and a ventilation return air raise. The methods used to predict or assess the blast-induced damage to each infrastructure element in response to stope extraction were:- intact rock strength testing,- discontinuity mapping,- linear-elastic static stress modelling,- blast-damage mapping,- near-field blast vibration monitoring and analysis,- geophysical assessment using inferred stiffness and wave velocity methods, and- post-extraction void assessment.The results of the detailed blast damage prediction and assessment program at the mine site have been discussed by the primary author elsewhere (Fleetwood, 2010). The current work will address blast-induced damage to mine infrastructure as a result of extraneous blasting vibrations from stope production blasting. A method for predicting the amplification of excavation surface motions from reflecting body waves will be discussed as well as the results of damage mapping around the study stope. The results of the damage mapping program identified blast-induced damage that occurred to the surface of the explosives storage magazine and local stope access development. No damage was observed at the main fault crossing or return air raise where higher vibration amplitudes were measured or predicted.

Dec 6, 2010

A mining companyÆs approach to managing the risk of theft of explosives and initiating devices should be underpinned by an organisation-wide policy developed with internal and external consultation. It should be based on the principles of sound proactive risk management, planning, monitoring and remedial action. This paper aims to provide mining (and construction)organisations with the rationale and many of the tools they need to control explosive security risks. As with all legislative compliance, they are best managed by incorporating the statutory and legal requirements into company policies, management systems and plans, operating procedures and culture. This is the approach that has been adopted in this paper. Trends we should expect: more prescriptive legislation and stricter government regulations; enhanced enforcement and more prosecution; more sophisticated detection systems, eg airports; additional compliance costs; additional vigilance on record keeping; improved risk awareness and risk communication; wider use of explosives policies, management systems and plans; and additional security staff with investigative skills.It should be noted that mining companies will be required to play their part in reducing the likelihood of explosives, intended for mining purposes, being wrongfully used to threaten, hold to ransom or to injure individuals or members of the public or to produce property damage. This will be done by putting in place safeguards to reduce the risk of theft of explosives while they are under their control. On that basis, this is a business risk assessment rather than a hazard risk assessment. A conclusion of this paper is that mining companies can and should play their part in reducing the supply of explosive materials that can then be used for illegal activities. In fact, mining companies have always had this duty, but now the stakes are higher û æcomplacency no longerÆ.

Jan 1, 2004

By P Warner

Mines are often located in remote areas that are not well served by æstiffÆ power grids. Radial transmission networks, high lightning incidence (eg in South Africa the Witwatersrand experiences seven to ten strikes/km2 per year), low short circuit strengths and diesel generation are not uncommon. All these factors result in the electric power supply to many mines being unusually prone to dips and disturbances. æLegacyÆ winder drives û cyclo converters and dc drives û convert power directly from the supply to the motor, with no intermediate energy storage element. Further, they rely on the supply network for commutation and are therefore sensitive to supply voltage disturbances. There is a high probability that a dc or cyclo mine winder will trip during a supply disturbance, often resulting in lost production time and call-outs for technical staff to reset or even repair equipment. In contrast, a voltage source inverter (VSI) ac drive stores a large quantity of energy (in the dc link capacitors) and is fully self-commutating. Hence, this topology is inherently more immune to supply voltage disturbances. Indeed, vendors of ac VSI mine winders make general statements about the superior performance of their drives during supply disturbances. However, the advantages have apparently not been previously quantified. This paper compares different winder drive topologies and their sensitivity to supply disturbances, considers categories of supply disturbances and quantifies the cost of the effects on the different drive types.

Jan 1, 2005

By Smith I. W

Australia has, and faces, a growing problem with regard to the ability to meet the demand for liquid fuels from indigenous petroleum resources. The position for natural gas is better but there is no room for complacency. Since the coal resources are relatively extensive, interest in the prospect of producing liquid fuels from coal is in- creasing. The approaches to the production of gaseous and liquid fuels are briefly reviewed and the present status of coal conversion technology is discussed. Many problems remain to be solved and it is estimated (in the USA) that another 8-10 years will be required before any of the processes for liquid fuel production are considered sufficiently efficient and viable to go to a demonstration plant. Coals represent complex feedstocks and the effects of variations in coal properties on oil-from-coal processes are not fully understood. The thermal efficiencies of various coal conversion processes are considered in relation to their impact on coal requirements. The production of Australia's present requirement for liquid fuels by the only commercial process in operation would require a four-fold expansion in the local consumption of coal. Any assessment of the suitability of oil-from-coal processes currently under development overseas for Austra- lian coals and requirements must take heed of the differences in coal properties and motivation. The economic via- bility of processes for producing oil from coal will continue to be uncertain because of the large difference between the World price for crude oil and the actual production cost.

Jan 1, 1975

Mine reconciliation is the practice of comparing the tonnage and grade of material processed by the mill with the tonnage and grade of ore in the reserve model of a deposit, and with the tonnage and grade in the grade control models used to de

Jan 1, 1998

Silica and limestone fluxing levels in copper smelting slags were studied. Copper concentrates with flux additions were smelted to matte (55.5 per cent Cu) and slag in a pilot scale submerged combustion furnace.Results indicated that oxidic and sulphidic copper levels in slags were minimised with a slag Si02 level of 36 per cent and a SiO2/CaO ratio of 5.5. Total copper losses in slags were 0.6 per cent under these conditions.To produce the desired slag chemistry, additions of bulk silica and limestone to copper concentrates of fluctuating grades were predicted numerically. The method employed the solution of two simultaneous equations, each respectively for silica and limestone calculations.The predicted flux additions were applied in a further series of tests and the resultant stages were found to be satisfactory. The method is applicable to smelting 'operations which employ two flux bins, with weigh feeders, so that slag chemistry may be controlled with the flux/concentrate feed mix.

Jan 1, 1985

By B, T Norgate, S Sanetsis, R Davidson

Global cement production accounts for about five per cent of man-made CO2 emissions (WBCSD, 2002). Such operating practices will increasingly be considered unsustainable, unless significant reductions in environmental impact can be realised by the industry.Slag is a high volume waste product from ironmaking, with about 300 kg of slag being produced per ton of iron. Critically, one ton of slag waste, if used as a replacement feedstock for Ordinary Portland cement (OPC), can prevent around one ton of emitted CO2 since no calcining is required. Slag cement blends can also show superior properties compared to OPC, such as lower heats of hydration and higher late strengths, but more development is needed to overcome their low early strengths. Rapid quenching of molten slag is required to produce æhydraulically-activeÆ binder when reacting with OPC; but water quenching can also require between five to ten tons of water per ton of slag at the plant. æDryÆ granulation (atomisation) is emerging as an alternative technology, the resulting solid product does not require drying, and possibilities exist for recovering heat energy from the hot slag.CSIRO Minerals has well-developed skills and equipment in pilot-scale pyrometallurgical treatment, and granulation of molten slag, including traditional wet, and also dry methods. Techno-economic desktop studies can also be used to help quantify factors such as value-adding of treated waste products, potential reductions in CO2 emissions and carbon credits, reductions in water consumption, and the possible decreased energy costs associated with fine grinding of dry slag granulate.The authors will present preliminary results from slag atomisation/dry granulation testwork (0.5 - 2.5 kg scale) and associated modelling studies, conducted using a æsyntheticÆ and industrial ironmaking slag. Outcomes from a techno-economic study on production of cement utilising wet or dry atomised slag granulate will also be discussed in detail.

Jan 1, 2004

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Split Rock low grade copper prospect was discovered in 1969 by Cyprus Mines Corporation using stream geochemistry. Cyprus "Imes carried out geochemical and geophysical investigations, geological mapping, and percussion and diamond drilling, and concluded that the grade of mineralisation was too low (0.1% copper) to be of interest. In the present study, the geology was remapped and very substantial differences from the previous observations are recorded. (lineraliced acid dykes in a 1 000 foot hole drilled by Cyprus Mines had a total inter- section of almost 300 feet with an average crade of 0.4% copper. Surrounding drill holes at distances of 500 feet did not intersect +hese dykes. This group of drill holes occupies a small part of an area about 2 km by 1 km which was affected by intense quartz sericite pyrite alteration along many fractures with an associated soil copper anomaly. It may be that the quartz sericite alteraiion with feeble copper mineralisation represents hydrothermal alteration emanating `rom a mineralised intrusion of which the dykes mentioned above are off shoots.

Jan 1, 1978

By A Purvee, M F. Lee, L J. Mollison

Oyu Tolgoi is a large Cu-Au porphyry deposit in the south Gobi desert, Mongolia. The first of several deep, large-diameter, concrete-lined shafts, Shaft 1, is nearing completion. It will have a finished depth of 1380 m at a diameter of 6.7 m. These shafts will provide access to and hoisting capacity for block caving of deep underground ore. Geotechnical site investigations, and associated predictions of stability and ground support requirements, are compared against actual construction performance. Routine mapping is essential, along with checks against predictions and informing the contractor of ground conditions and variances.Advance rates are compared against predicted rock mass quality. A reasonable correlation exists between Qwall and advance rate. Overbreak and concrete liner thickness is related to the blockiness quotient, RQD/Jn.A ætool-bagÆ of just a few support elements (chain-link mesh, fibrecrete and 2.4 m long friction anchors and resin grouted re-bar bolts) was able to cope with the ground conditions encountered. QA/QC procedures are essential from the factory, through site storage to installation.

Jan 1, 2008

Magnesium-rich olivine is used as an additive in LKABÆs iron ore pellets in order to improve the high-temperature properties of the finished products. Olivine is only added to the pellets that are manufactured for ironmaking in the blast furnace process. The olivine comes from Minelco/LKABÆs mine at Seqi in Greenland. This dunite complex of Archean age contains about 95 - 98 per cent olivine. The grain size is typically 1 - 3 mm but much larger euhedral olivine crystals are common in the porphyritic type. The serpentinisation is absent or weak. The most common minor minerals are chromite, chlorite, talc, phlogopite, amphibole and pyroxene. The crushed olivine is transported to LKABÆs pelletising plants in Northern Sweden. After grinding, small amounts of olivine are mixed with the magnetite concentrate. The concentrate is rolled into green balls, about 10 - 14 mm in diameter. The moist green balls are transferred into the pelletising machine where the maximum temperature is about 1250¦C. The residence time in the pelletising machine is about one hour. Olivine is used in order to get pellets with better high-temperature properties. This paper deals with the olivine alteration during the pelletising process and the behaviour of magnesium following the decomposition of magnetite. The reactions are quite complex in the pellets because the physico-chemical conditions vary considerably in the process from one process step to another, and in the pellet bed from the top to the bottom. Some olivine particles in the finished product show very slight alteration, some particles are completely decomposed. The formation of the iron-rich coronas around the olivine particles is the most typical alteration. In the finished pellets the magnesium is mainly distributed between the following phases: unaltered olivine, coronas, Mg/Fe-ferrite and silicate slag.

Jan 1, 2008

By M B. Lovitt

At present there exist few engineering calculations and principles to determine exclusion zones for personnel in the vicinity of underground explosive storage areas. This paper is written to encourage discussion and proposes a method to determine the impact of a blast wave through scientific principles. Then, criteria to determine an ‘exclusion zone’ need to be identified.There has been much work on identifying the pressure rise and the energy of explosive detonations underground but little to develop standards in criteria that can be used to identify exclusion zones for useful design of underground infrastructure. The author presents the newest ways of calculating the pressure rise and energy (impulse) of detonations and puts forward some criteria to be used in the identification of personnel exclusion zones to spark peer review and discussion of these criteria towards developing standards for engineering design.Smith and Sapko (2005) used Sach’s scaling laws to develop a relationship for both pressure rise and impulse, which incorporated factors for intersections. Intersections will have a large bearing on the peak pressure and the energy of the blast wave and needs to be incorporated. Silvestrini, Genova and Leon Trujillo (2009) developed the scaling laws with an energy concentration factor to predict blast propagation in partially confined geometries and together the author has proposed equations for determining the peak side pressure and the impulse in a tunnel. Given the weight and type of the explosive, the average cross-section of the tunnel complex and the number and type of intersections encountered, the pressure and impulse can be calculated.The military has carried out many investigations as to the influence of blast pressure and impulse on the human body. Lung damage, ear damage and velocity knock down are three of the criteria standards that are presented as possible methods of determining exclusion zones around an underground explosives magazine. The author suggests that the velocity curves presented by Bowen, Fletcher and Richmond (1968) could be an acceptable method of determining an exclusion zone as it incorporates the side pressure and the energy of a blast wave to determine the ability of the wave to knock down personnel.CITATION:Lovitt, M B, 2014. Exclusion zone calculation for underground explosives storage, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Johns AS

Comissioning of a new residue disposal tcluding upgraded classification for none backfill preparation, new variable speed pumps and a new residue dam took place in 1¦76. The system is described.

Jan 1, 1978

Recent analysis of backfilling material has shown that a finer size distribution is preferable for stope filling. In order to increase crusher throughput and pit productivity, a reassessment of the quarrying operation was conducted. Part of that reassessment was a review of blasting practice. Six means of reducing the average muckpile fragment size were examined. Different blast initiation and charging options were compared, and patterns using smaller hole sizes were designed, analysed with the JKMRC 3x3o software, then drilled and fired. The ground vibration and face movement was recorded and compared. To determine whether the Kuz-Ram model could be used in an economic analysis of the quarry operation, the fragmentation distribution of the small diameter hole blasts was determined. Photographs of the muckpiles were taken and digitised. However subsequent analysis indicated that a satisfactorily large photo sample was only obtained from the smallest diameter hole blast. The Kuz-Ram fragmentation model prediction was found to be within the confidence limits of those results. An engineering and cost comparison between the blasts was made.

Jan 1, 1995

By He F, Zhu D

How to monitor and control the support and surrounding strata system on a longwall face effectively is one of the major research problems in ground control. Based on observations on movements of the support and surrounding strata of face No. 2703 of Dongpang colliery, the relationship between the downtime related to support and surrounding strata and other influential factors is analysed systematically in this paper. Monitoring indices and control measures are then determined by taking corresponding downtime as an objective function. When the monitoring method, developed from the above findings, was used on face No. 2703, the downtime due to support and surrounding strata was remarkably reduced, and the face advanced Normally.

Jan 1, 1992

The present stage of economic development of the Broken Hill lode, attained after 40 years of active exploitation, leaves little opportunity for the study of the zone of secondary sulphides.Little remains of the oxidised zone, and the observations of the secondary sulphides of copper and silver can rarely be made on specimens collected in situ. A few specimens containing secondary...

Jan 1, 1927

All large open pits in Australia have been mined, or are planned to be mined well below the local water table. This raises several issues that impact on mine safety, mining costs and regulatory approvals. Some pits will be æwetÆ, where they are mined through permeable horizons and where there will be measurable groundwater inflows. These will require some form of dewatering. There may also be some difficulties in the disposal of excess water. Other pits, may be ædryÆ, where they are mined through impermeable material and there are no measurable groundwater inflows but where there are stability issues related to hydrostatic pressures within the pit walls. These may require some form of depressurisation. Some pits are a combination of both. Effective management of groundwater inflows and groundwater related stability issues and the development of cost effective and environmentally acceptable dewatering and depressurisation systems requires an understanding of site specific hydrogeological conditions and practical experience in what works best for different conditions. The presentation will include an outline of the key hydrogeological factors that impact on large pits, practical methodologies for achieving dewatering/ depressurisation, and some case studies from the Goldfields, Pilbara and North Queensland.

Jan 1, 2003

By H Plewes, A Bur, L Murray, J Pottie

Water recovery from tailings for reuse in mineral processing is essential to operation of mines in the Atacama Desert of Chile. With annual rainfall of 5 mm, the prudent and efficient use of available water resources is a major issue for the Escondida Mine and other mines in the area. The Escondida Mine is located at an altitude of 3100 m, in a very arid, seismically active part of the Atacama Desert of northern Chile. The site is located about 170 km from the coastal city of Antofagasta. From 1994 to 2002, tailings were discharged into the Hamburgo Tailings Facility, which comprises a series of æpaddiesÆ located near the open pit and mill. Because water in the region is only obtainable from groundwater sources, the paddy system incorporated a number of design features with the aim to maximise water recovery from the tailings. As part of the recent mill expansion to 237 500 metric tonnes per day, a new tailings facility, the Laguna Seca Tailings Facility, projected to be one of the largest tailings facilities in the world, was commissioned in 2002. Extensive studies were conducted for the design of the new facility to predict water recovery from the conventional wet disposal of tailings. The predictions were calibrated against the performance of the Hamburgo Tailings Facility and subsequently re-calibrated against actual performance during the first year of operation at the Laguna Seca Tailings Facility. Initial operation of the Laguna Seca Facility was marked by a coincidental change in tailings characteristics from design, which highlighted the need for thoroughly understanding tailings behaviour during deposition, and the parameters and deposition techniques that could enhance water recovery. Systems have been put in place to manage the tailings deposition and respond to changes in key parameters such that water recovery targets can be reliably achieved. This paper describes the background studies that were conducted to evaluate evaporation and tailings behaviour, summarises the water balance and then presents some observations from the commissioning and start-up of the facility.

Jan 1, 2003