Search Documents

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

The Bau Goldfield lies in the southwestern corner of Sarawak in East Malaysia. Evidence of past mining in the form of open pits and adits can be found over an area of 250 sq kin, centred on the township of Bau. Chinese were mining gold in the district as early as 1820. The Bau Goldfield so far has produced approximately two million ounces of gold, from alluvial deposits and over 50 hard rock mines. The largest single producer was the Tai Parit mine (700 000 oz) which was operated by the Borneo Company from 1898 to 1921 and by a local Malaysian family from 1991 to early-1997. Over the past ten years, gold resources totalling around one nullion ounces have been delineated through systematic exploration using modern techniques, with the bulk of the resource hosted in two deposits (Jugan and Pejiru).Triassic to Jurassic andesitic volcanics and coeval intrusives are the oldest rocks that crop out in the Bau Goldfield. These igneous basement rocks are unconformably overlain by 500 m of late Jurassic, massive, micritic limestone which in turn is overlain by a 1500 in thick flysch sequence, composed mainly of shale. Basement rocks and limestone are exposed along the hinge of a ENE-striking anticline that passes through the Bau district (Bau Anticline). A NNE-striking belt of Miocene granodiorite porphyry stocks and dykes also passes through the Bau Goldfield. All of the known gold deposits lie within 5 km of this zone of intnisives, with a concentration of deposits at the intersection of the intrusive hell with the Rau Anticline.

Jan 1, 1997

It is indeed a pleasure to be here this morning to open the 4th Mill Operators' Conference. It is no mean feat to organise such an event and I would like to congratulate the committee for the work that they have done. I am sure that the Conference will be an outstanding success. I welcome overseas visitors and hope that they gain and share in the openness of this Conference. There is personal satisfaction for me to speak to you as a mining engineer addressing a large group of metallurgists and mill operators. I would have thought that it would be impossible for a mere mining engineer to inform a metallurgist of anything. I will desist from using such derogatory terms as "xanthate munchers", "bubble makers" and "glorified mathematicians". Terms of endearment as these may not be seen with much equanimity. Such is the warm association that the two professions have enjoyed over the years. The economic climate that we at present face is a major problem to all of us. I wonder how many people here come from mining operations that are in trouble financially or that are cutting back in one form or another. This is the recession that we needed to have. When the world's greatest treasurer can tell us that then we truly have a lot to fear. The present downturn can be seen as a normal adjustment in the cycle of our business. Yet the world does not experience such severe adjustments as frequently as we experience ours. The root cause for the regular adjustments can be placed at the feet of inflation. Until the politicians of this country of ours can come to grips with inflation, we will continue to experience downturns on a 5 to 7 year cycle. This, in my opinion, is the basic reason why we appear to experience more downturns than the rest of the world. We simply price ourselves out of the market. This takes about 5 to 7 years to be highlighted and then we need to make adjustments. However, this recession is worldwide. The adjustments usually take the form of redundancies, retrenchments and early retirements. What is the solution?

Jan 1, 1991

By Ovchinnikov YN, Novikov VS, Spirin NA, Babushkin NM, Mysik AF, Shcherbatskii VB, Kukarkin AS

Laboratory investigations were carried out to determine the resistance coefficient of the flow through beds irrigated with wetting and non-wetting liquids. A formula was obtained which may be used to evaluate the resistance of the irrigated packing. Quantitative investigations were also carried out on operating furnaces at Magnitogorsk. Continuous measurements of the lower pressure drops were made under different furnace conditions. Pressures were measured in the tuyere space and the bosh region. A significant transient behaviour of the pressure drop was observed in the irrigated zone as a function of the accumulation of the liquid phase in the bosh region as smelting progressed. Additionally, transient processes were also investigated in the upper furnace zones. The basic cause of the transient behaviour was shown to be the irregularity of burden descent caused by the casting cycle. It was shown that the rate of burden descent between consecutive casts reflects fairly accurately the accumulation and drainage of the liquid products as a result of which heat transfer, reduction and aerodynamic processes assume transient character. In practically all cases of casting a decrease in blast pressure and that over the furnace height of 0.2 kg/cm2 was observed. The analyses of radial gas composition at the stock line showed that compositional variations connected with the casting cycle are most pronounced in the central and peripheral regions, whilst in the intermediate regions the conditions are relatively stable. Calculations show that as casting progresses there is a decrease in the gas flow rate at the periphery and an increase in the centre of the furnace. The transient nature of the aerodynamic processes in packings revealed the existence of an appreciable reserve capacity. Elimination of transience was tested on the furnace at Magnitogorsk and improved operating and economical furnace parameters obtained.

Jan 1, 1975

The operation of quarries for the production of crushed stone and aggregates, depends heavily on rock blasting efficiency, which usually represents a major share of total production costs. After investigating the causes of this situation, a series of technical aspects have been detected, and they are described for the purpose of contributing to the minimization of costs, which also reduces the effects of blasting on the environment. Utilization of empirical design methods, of inadequate explosive types, and of erroneous drilling pauems with respect to rock properties, are the main factors to be corrected, as a consequence of poor engineering criteria, with scarce use of computational methods and field instrumentation. Several concepts of blasting optimization are pointed out, and their application to industrial operations in a Portuguese limestone quarry indicated clear trends for the reduction of production costs, as well as some of the deleterious consequences of blasting on the environment.

Jan 1, 1990

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

Au airway hteat and moisture exchange .,Jgorithm is described which is generalised to suit most mining situations and can be run separately on a microcomputer or used within a network simulation. The main difference between this technique and other simplified methods is that a non-uniform boundary condition is allowed for. This permits radiative heat transfer between surfaces of different wetness in addition to evaporative and convective heat and mass transfer.

Jan 1, 1988

The Ok Tedi Project has been planned as a selective mining operation since the Feasibility Study. The nature of the orebody, and the need to 'stage' the infrastructure buildup meant that initially the mill would process gol ore using a leach-CIP process, followed by parallel leaching of gold ore and flotation of copper ore, and finally all flotation of copper ore. Cutoff grades were applied to gold and copper ore of 1.0-1.3 g/t Au and 0.4-0.3% Tot. Cu. Since startup, unpredicted occurrences of sulphide copper and, to a Lesser extent, carbonaceous material, has necessitated significant additional short term drilling (other than at grade boundaries), and shift grade control in the pit to control contaminant levels. Remodelling of the orebody based on the most up to date variography and geological interpretation has had a significant impact on the reserves, and thus the whole project development strategy; necessitating the earlier processing of copper ores, and preflotation of the gold ore.This paper discusses some of these points in detail, and in particular highlights how unforseen geological occurrences coupled with processing restrictions can have significant impacts on ore reserves and the mine development schedule.

Jan 1, 1986

By Daniels E. J, Morgan W. A

In response to the increase in consumption of galvanised steel for automobiles in the last decade and the problems associated with remelting larger quantities of galvanised steel scrap, a process is being developed to separate and recover the steel and zinc from galvanised ferrous scrap. The zinc is dissolved from the scrap in hot caustic using anodic assistance and is recovered electrolytically as dendritic powder. The dezinced ferrous scrap is rinsed and used directly. The process is effective for zinc, lead, and aluminum removal on loose and baled scrap and on all types of galvanised steel. The process has been pilot tested for batch treatment of 900 tonnes of mostly baled scrap. A pilot plant to treat continuously loose scrap, with a design capacity of 48 000 tonnes annually, has been in operation in East Chicago, Indiana since early in 1993. The first 450 t of scrap degalvanised in the pilot plant have residual zinc below 0.01 per cent and sodium dragout below 0.01 per cent. Use of degalvanised steel scrap decreases raw materials, environmental compliance costs, and opportunity costs to steel- and iron-makers. Availability of clean degalvanised scrap may enable integrated steel producers to recycle furnace dusts to the sinter plant and EAF shops to produce flat products without the use of high quality scrap alternatives such as DRI, pig iron, or iron carbide. Recycling the components of galvanised steel scrap saves primary energy, decreases zinc imports, and adds value to the scrap. The quantities of zinc available by the year 2000 from prompt and obsolete automotive scrap will approach 25 per cent of zinc consumed in the major automotive production centres of the world. Zinc recycling from galvanised steel scrap, either before or after scrap melting, will have to be Implemented.

Jan 1, 1993

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By Ho E

Analyses of several nickel mattes from around the world show a significant variation in their copper content. Typically, matte contains an alloy, heazlewoodite and a copper sulphide phase. The various commercial methods of processing these mattes are reviewed and some of the fundamental factors which determine the choice of leaching system are discussed. Electrochemical studies on pure heazlewoodite and millerite in sulphate and chloride media are compared which show that nickel sulphides react via a series of nickel deficient sulphides and exhibit passivation as nickel is removed. Differences in the electrochemical behaviour of nickel sulphides in chloride media are attributed to greater crystallinity of sulphur and less formation of'NiS2. The electrochemistry of mattes differs because of the presence of alloy and copper. Copper in the matte modifies the potential for alloy dissolution and the rate of anodic dissolution of nickel. At elevated temperatures, Cu(II) in solution exchanges with NiS and completes the leaching of nickel at relatively low potentials without significant oxidation of sulphur to sulphate. It is concluded that there are fundamental advantages to leaching nickel matte in chloride media using Cu(II)/Clz as the oxidant.

Jan 1, 1996

By A R. Bonani, M P. Pe±a

The optimisation of slope angles, that is to say, increasing them, compared to the original design is always the subject of analysis of stability for geotechnical engineers and economic analysis for planning engineers. Questions to be answered include: What is the acceptable risk? What factor of safety? What probability of failure or reliability? The Rosario Open Pit has a history of failure, poor quality rocks and high pore pressures. It was decided to deepen the pit below the programmed design to test the practicality of different design approaches, which if successful, could be used to improve the economics of mining at Collahuasi. The revised slope design has factors of safety in the range of 1.0 to 1.2, probabilities of failure of ten to 38 per cent, and increased slope angles of between 3¦ and 5¦ with respect to the original design. The pit deepening with these design slopes will deliver an extra two million tonnes of ore which will have a significant positive impact on mining economics.

Jan 1, 2007

By Dunlop A. C

A brief study from the Mt. Bulga prospect com- pares the chemistry and mineralogy of different soil fractions and other materials to suggest a sequence of surficial metal dispersion from adjacent gossans, which may have relevance for geochemical exploration in semi-arid terrains. v v v v v JIV-- v v v v a o v o/ v v v v 1 v v lv ./v '' 1 v 16400N ..I v 1635014 v 1630014 .:1 ò.t SILURIAN sillstone " lelsic volcanic sillstone -sandstone ORDOVICIAN Eandesite o quartz float gossanò pits doOP Iv o shalt v _--'fault v 1---1 soil traverse v v v v 0 100 200 mm e Fig. I Local geology and location of soil traverses, Mt. Bulga (compiled from Chisholm, 1976). The Mt. Bulga prospect in central New South Wales is a small but well documented volcano- genic massive sulphide occurrence (450,000t of 0.8% Cu, 1.3% Pb, 5% Zn and 0.45 g/t Au) Cambrell and Kirk (1974), and Chisholm, (1976). Mineralization is localised near the interface of felsic pyroclastics with overlying silt- stones and along adjacent faults (Fig. 1). In this area with a Koeppen type cf6 climate, soils are thin and skeletal along ridges with thicker and better differentiated profiles with a colluvial component up to 2m thick developed

Jan 1, 1988

Alcoa of Australia's Western Australian bauxite mining operations in the Darling Ranges, southeast of Perth, present major challenges in the control of air blast. The close proximity of rural communities and the face profile make the traditional methods of air blast control difficult.An extensive blast noise monitoring programme has been established. The development of a computerised blast noise prediction model and the establishment of a radiosonde weather balloon facility have reduced blast induced complaints by a factor of ten.The meteorological factors affecting blast noise transmission are discussed and examples are given of adverse weather conditions for the southwest region of Western Australia.

Jan 1, 1983

By Walton M. C

A combination of flotation and smelting technologies is proposed as a cost-effective means to maximise the revenue of base metal operations. The proposed treatment route breaks the grade - recovery nexus associated with the treatment of ores exhibiting difficult mineralogy in conventional plants. Aspects of the two technologies are reviewed and typical capital and operating costs presented. A significant improvement in revenue is demonstrated in a worked example, where a copper-lead-zinc operation is examined in terms of the conventional and proposed treatment options. For the selected ore, the net smelter return per tonne of mill feed improved 57 per cent, from US$89.70 to US$141.10 with the proposed treatment option. This represents an additional US$51.4 million in annual revenue. Metallurgical operating costs increased by US$20.12 per tonne of mill feed for an incremental capital requirement of US$30.3 million for an existing operation.

Jan 1, 1992

By A R. Hollis, M Heddon

The safe life cycle of a Tailings Storage Facility (TSF) is founded on the fundamentals of proper design, construction, operation and closure. Leinster Nickel Operations (Leinster) utilises four active TSF cells that are cycled between filling (deposition), desiccation, and construction to meet a targeted rate of rise. This results in ongoing and consistent raising of the TSF walls. Critical to maintaining the safe life cycle through this consistent wall raising is precision construction and high frequency quality assurance to ensure compliance to design requirements and TSF walls free from defects. Leinster has recently deployed Intelligent Machine Control technology for TSF construction. Advances in Intelligent Machine Control have decreased variability in construction; ensuring variations are within the tolerances of design. The Intelligent Machine Controls are programed to ensure construction conforms to design tolerances of +/-30mm. This level of accuracy provides assurance of borrow area set out, compacted layers are as per design, compaction monitoring is within the zone placed, scarification between layers to prevent lamination is maintained, and batter angles are set to the correct grade. This level of control provides certainty that construction meets the design intent. In conjunction with Intelligent Machine Control, periodic drone surveys are conducted to verify construction against design. Advancement in survey equipment and techniques allow higher frequency, high accuracy survey to be completed on demand by site based personnel. This provides quality assurance through all stages of the construction phases, as well as the final constructed wall, ensuring compliance to design. Combining Intelligent Machine Control with higher frequency quality assurance provides an increased level of certainty that the TSF construction is defect free and within quality specifications. These recent technological advancements in Construction and Quality Assurance ensure cell raises are constructed to the design intent with greater levels of accuracy and precision than ever before.

Jul 1, 2021

By Crosby N. R

The design of mine openings and the assessment of their reserve are processes ihicl, require the routine manipulation of considerable amounts of data. A number of computer programs have been assembled to operate in a mini computer in order to provide some mechanical assistance for these processes. The system responds to plain language commands. which allows mining engineers to compute the reserves for a number of possible mining outlines, on an interactive basis. Methods of numerical analysis were used in preference to statistical or qeostatistical techniques.

Jan 1, 1977

By G D. Richmond, J C. Chomley

Copper has been mined intermittently at Gunpowder, north of Mount Isa, since 1927. Most ventures have had some initial success but fluctuating copper prices, the small-scale of the operations and the remoteness of the site led to closures or sale. Processing routes have included direct sale of high grade ore, flotation of oxide and sulphide concentrate, and copper cement production from mine solutions. Copper cathode has been produced by heap and in-place leaching coupled with solvent extraction and electrowinning (SX/EW). Aberfoyle Limited recently purchased the Gunpowder operation and is expanding operations. An innovative high recovery tank leaching process, including a low temperature, low pressure autoclave, has been adopted. Copper cathode will be produced from an expanded solvent extraction/electrowinning plant at approximately 45 000 tonnes per year. The combination of expanded throughput and high metal recoveries will make Gunpowder a cost competitive producer.

Jan 1, 1998

By Szymanski J

Although efforts towards producing a `total quality rockfill product' have allowed cemented rockfill costs to be reduced considerably, there is still tremendous potential for further cost reductions. Cemented rockfill costs range from approximately $7 to $12 (US) per tonne of fill placed. Approximately 50 per cent of the rockfill costs are associated with cement costs. A large portion of the remaining 50 per cent is associated with labour and materials handling costs. Several Canadian underground mines utilise haulage trucks and/or conventional belt conveyors to distribute the rockfill. However, due to the restrictive nature of the underground environment, these current materials handling systems have limitations (ie spillage from trucks, dust from conveyors). The Sicon conveyor system (developed in Sweden) has considerable potential for replacing these current methods. The Sicon conveyor utilises a revolutionary approach - the conveyor belt is folded over upon itself (forming a tear drop shape) so that the transported material is completely encased within the belt. The Sicon conveyor's ability to negotiate very tight comers (without transfer points) makes the conveyor very appealing for underground mining applications. An analysis comparing the pros and cons associated with the Sicon conveyor system versus conventional materials handling systems will be presented in this paper.

Jan 1, 1995

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016