Search Documents

By R J. Butcher

Many deposits have been evaluated as potential block caves over the last 20 years due to the perceived benefit of low operating costs. However, block cave projects are typically capital intensive, with mass mining providing high throughput rates that required large investments in mining, processing and utilities infrastructure. While the key economic metrics in deciding to proceed with a caving project are typically net present value (NPV) or internal rate of return, these may not represent the best decision metrics for some companies. Where a caving project is competing for scarce capital amongst other projects in a company’s portfolio or where the caving project is the only project being evaluated by a company trying to raise capital, other metrics may be more appropriate. This paper explores the use of present value ratio and the minimising of maximum negative cash flow as suitable metrics in determining alternative strategies. Trade-offs between optimising for economic value and capital efficiency measures allow for decision-makers to evaluate potentially higher-risk, higher-capital and maximum NPV projects against lower-risk, lower-capital projects.CITATION:Stewart, C A and Butcher, R J, 2016. Block cave evaluation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 809–816 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Nehring, M Kizil, P Knights, A Mousavi, F Sotoudeh

A cut-off grade is used to distinguish an economically viable block of ore from non-economical ones in mining operations. In order to obtain a high Net Present Value (NPV), a strategic and precise determination of cut-off grades (mill feed/marginal, marginal/waste) is required. In recent years, the significant depletion of feed grades and increasing mining operating costs have affected the viability of new and existing mining operations. Hence, the introduction of a pre-concentration system to process ore before sending it the main processing plant has gained increasing attention for its potential improvements in resource exploitation processes, mineral processing, energy consumption and environmental impacts. The primary potential advantage of implementing a pre-concentration system is the improvement of resource utilisation and increased reserves as a result of a reduction in cut-off grade. The objective of this paper is to present a new cut-off grade method, which can be used in the presence of a pre-concentration system for underground metalliferous mining operations. The results of this study illustrate the potential economic benefits of using a pre-concertation system prior to a mineral processing operation as a result of the reduced cut-off grade and increased NPV.

Nov 10, 2020

By A P. Wibowo

Indonesia holds a significant role in the utilisation of coal resources in the world. Although the number of Indonesian coal resources and reserves do not fall into the world’s top ten, according to 2009 statistics, Indonesia is the seventh largest producer of coal with a production of 256 Mt. More than 80 per cent of this amount is sold in the export market, making Indonesia the world’s second largest coal exporter. Most of the exported coal from Indonesia is used to fulfil the needs of the Pacific market, such as Japan, Taiwan, China, among others. It is also possible to reach the Atlantic market.Along with Indonesia’s development program, until 2025 the Indonesian government has adopted a National Energy Policy that aims to reduce the role of petroleum in electricity generation and replacing it with coal. As a follow-up of the policy, since 2009 PT PLN, the state electricity company has built steam power plants throughout Indonesia as an implementation of the first stage of the Electrical Acceleration Project with a capacity of 10 000 MW. Moving forward, in 2011 PT PLN will also build the second stage of the project with a capacity of 10 000 MW. As a result of the program, the domestic need for coal is expected to increase as much as 44.8 Mt.With the increase in domestic need and decrease in the number of reserves, the Indonesian government has adopted policies to secure the domestic coal supply. A policy that may potentially be adopted by the government is the limiting of coal production, seeing the high rate of increase in Indonesian coal production. The adoption of such a policy will change the distribution map of coal in the Pacific market. Thus, this paper will evaluate the change of coal distribution patterns in the Pacific market along with the increase in Indonesian domestic needs and Indonesian adoption of policies regarding the securing of coal supplies.

Nov 22, 2011

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

By L Lachance, F Flament, D Leroux, S Gariépy

The pervasiveness of poor sampling practices in and around mineral processing plants could seem intriguing in view of the various documented evidences both for causes and consequences. To this extent, this paper revisits the well-documented but lesser-known fact that failure to care sufficiently about how samples are selected and managed is the mother source of almost all sampling biases. The authors believe that the potentially huge leverage between causes and consequences as well as the diversity of people involved in sampling call for a globally integrated solution rather than for a point solution. Such a globally integrated solution has already been put forward by the AMIRA P754 Metal accounting – code of practice and guidelines (AMIRA, 2007) that inherently requires accuracy to be targeted, measured, reported and managed. Furthermore, always in order to avoid a point solution, several layers of protection against biases must be put in place with each one involving a different ownership whenever possible. This is exactly the role intended by the supervisory bias detection method described in this publication. It is based on the continuous monitoring of the expected value of reduced residuals obtained from statistical data reconciliation conducted in a metal accounting context. This supervisory bias detection method is developed in full details after which Monte Carlo simulations are done on a mineral processing plant example for showing how it can be successfully applied for detecting hidden biases.CITATION:Lachance, L, Leroux, D, Gariépy, S and Flament, F, 2014. Detecting sampling biases in metal accounting, in Proceedings Sampling 2014 , pp 109–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Napitupulu P

PT Freeport Indonesia currently operates a concentrating complex capable of milling 127 000 metric tonnes per day of copper and gold hearing ore. The facilities consist of both a conventional crushing, ball mill and flotation circuit and a SAG, ball mi

Jan 1, 1997

The recovery of Copper by solvent extraction was arguably the most significant hydrometallurgical development of the 1960's. However, only dilute solutions at relatively high ph. could be treated effectively. ICVAcorga introduced in the 1970's the much stronger salicylaldoxime based reagents, which resulted in a dramatic change in plant configurations. So for example plants which normally use 3 extraction stages and 3 stripping stages could be reduced to 2 + 2 staging or 2 + 1 staging, even for high copper tenors at low ph. Leach liquors up to 40 g A copper are being treated at some locations so that almost any copper bearing liquor can now be purified by solvent extraction. Following a considerable amount of research and development effort ICI/Acorga have made further significant advances in the application of copper solvent extraction. The first of these is in computerised flowsheeting. In conjunction with ICI's Process Technology Department, Acorga have developed the Minchem Computer program, which uses laboratory generated equilibrium data to facilitate optimisation of metallurgical operating parameters. The program can operate in two modes, prediction and assessment so that given suitable extract and strip isotherms plant performance can be predicted for a given set of conditions. Alternatively existing plant performance can be assessed rapidly and accurately, thus providing a valuable quality control tool. Pilot plant work can now be restricted to evaluation of the physical aspects of the SX circuits, and to looking for the unexpected. Secondly using the patented 5-Nonyl Salicylaldoxime in precise admixture with a number of carefully selected strip modifiers, the Acorga M-range has resulted. Reagent selection from these new extractants can now be based on how the reagent can alleviate the remaining problems such as hydrolytic stability, transfer of iron, and organic losses by entrainment which may be related to particular features of the operating plant. Thus the Acorga M-range has enhanced and significantly extended the use of solvent extraction for copper, whilst refinements in the processing of metallurgical data has considerably simplified circuit design and analysis of results.

Jan 1, 1989

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That sub- ject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public atten- tion has focussed as never before on the subject of commodity prices. To advocate stabilizing com- modity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent f.11 1k

Jan 1, 1978

By D R. Lueking

A technology involving separate unit processes for the generation and use of ferric ions for the oxidation of sulphidic minerals has been developed. The technology utilises a stand-alone automated bioreactor for ferric-ion generation (termed SAAB-FIG) and produces a low pH, ferric ion-rich leach liquor with a high oxidation potential. This leach liquor is then employed, in a separate unit process, to oxidise sulphidic minerals and regenerate ferrous iron that may subsequently be recycled to the bioreactor for the continual generation of ferric ions. The technique was successfully applied for the recovery of copper from chalcocite (Cu2S) and chalcopyrite (CuFeS2), as well as other ores and concentrates containing copper sulphide minerals. Coarse ore, ground ore and concentrates were treated with acidic solutions containing 8 to 12 (g/L) Fe(III) ions at a variety of temperatures. This process yielded over 50 per cent of the contained copper from both chalcopyrite and chalcocite samples. Maximum reaction rates and copper recoveries were found to be highly dependent upon temperature and pH and leach liquors containing bacterial cells displayed little difference in their leaching efficiency when compared to cell-free leach liquors.

Jan 1, 2000

By Hocking G

For some underground structures, the use of the plane strain assumption in stress analyses may not be justified. The finite element method and photoelasticity have been used to obtain complete 3-D solutions, but, for various reasons, neither method has found universal use. The boundary integral equation method (B.I.E.M.) can be more efficient and economical than the finite element method for 3-D problems involving large volume to surface area ratios. A B.I.E.M. program developed for calculating stresses and deformations in infinite elastic media has been used to determine the 3-D distributions of stress around T- and Y- junctions of circular tunnels in stress fields in which the ratios of horizontal to vertical stress are 0, 0.33, 1.0 and 2.0. For the T- junction considered,stress concentrations at the intersection are approximately twice the plane strain values. Except where horizontal field stresses are high, the stresses in both tunnels approximate the plane strain values at about two tunnel diameters from the point of intersection of the tunnel centre lines. The stresses in the two branches reach those for the corresponding plane strain, two parallel tunnel case two diameters from the point of intersection of thq inner tunnel walls. Very high stress concentra- tions occur in the pillar of rock between the inner tunnel walls near the point of intersection.

Jan 1, 1976

By Mine F. J, Woods P. H

The Top End of the Northern Territory lies in the monsoonal zone and receives rain during the November-April period. Initially, at the start of the wet season, rain storms are localised, but, following the descent of the monsoonal trough from below the equator, widespread rain occurs. Overflow incidents at mine sites tend to arise midway through the annual wet season when excess water accumulated in ponds begins to discharge to the external environment. Remote-access monitoring may be undertaken at mine sites using equipment to continuously measure water quality parameters with storage of the information on a data logger. The data is then retrieved by visiting the site and transferring it to a portable computer or by remotely accessing the system using a telemetry system and transmission via telephone, VHF/UHF or satellite. Such systems are readily available and vary in cost depending on the sophistication of the data transfer system. Available sensors for continuous monitoring include those for conductivity, temperature, pH and other ion selective electrodes, eg nitrate, and water level. Of these variables, conductivity is most useful due to its inherent accuracy and stability of reading. Remote monitoring capability is able to provide: (i) more intensive monitoring of key issues; (ii) more timely information; (iii) correct perspective on the degree of environmental problem; and (iv) information from remote locations, which would be difficult to monitor by more conventional methods. Examples are given for applications of continuously logged measurement of conductivity of waters discharging to drains and in creeks at Pine Creek, Ranger, Nabarlek and Woodcutters mines in the Northern Territory. These applications demonstrate the timeliness of the continuous monitoring technique.

Jan 1, 1994

By Treglown N

In any mining operation the curtailment of rising operating costs is of prime concern to management.One area of activity where costs are often disguised is that of longhole secondary breakage.This paper outlines sane operational techniques that have been considered and tested, resulting in improved fragmentation fran longhole stope blasts at New Broken Hill Consolidated Limited mine, Broken Hill, NSW.

Jan 1, 1985

By E Ben-Awuah

Mine planning is the backbone of all mining enterprises and determines the profitability or otherwise of any mining investment. Providing high quality ore and tailings containment at the right time are the main drivers in oil sands mining. Recent environmental and regulatory requirements also makes waste management an integral part of mine planning in the oil sands industry (Directive 074). Due to the limitation of lease area, the pit phase advancement in oil sands mining is carried out simultaneously with the construction of tailings dykes in the mined out areas of the pit. These in-pit dykes are constructed to hold tailings that are produced during the processing of the oil sands ore after an initial external tailings facility. Most of the materials used in constructing these in-pit and ex-pit dykes come from the oil sands mining operation, making it necessary to have a plan for supplying the dyke material. The research problem here is categorised as: determining the order of extraction of ore, dyke material and waste to be removed from a predefined ultimate pit limit over the mine life that maximises the net present value of the operation û a strategic schedule; anddetermining the destination of dyke material that minimises construction cost depending on the construction requirements of the various dykes as per their designs û an operational schedule. There has been developed, implemented and verified a theoretical optimisation framework based on mixed integer goal programming (MIGP) to address the oil sands long-term production scheduling and waste management problem. The research introduced the development of multiple material types and multiple destination optimisation techniques using MIGP in the context of mine planning. This study presents an integration of mixed integer programming and goal programming in solving large-scale mine planning optimisation problems using clustering and pushback techniques.

Sep 26, 2011

By R Cooksey

The Globe-Progress Mine is an open pit gold mine that is part of the larger Reefton Goldfields deposit located on the West Coast of New Zealand. The regional geology comprises a series of north to south oriented fold structures that have undergone post-deformation mineralisation. The structural geology within the mine itself is more complex, with major shears hosting numerous high-grade mineralised quartz shoots and splays that have been historically mined.The selective mining of ore within the pit is challenging due to the orientations of the hanging wall and footwall areas of the main Globe shear zone, the lithologies of these areas which range from highly brecciated and sheared material to competent mineralised host rock, and in the hazards presented by the numerous old historic underground workings. The coordination of drilling, modelling and excavation of the ore requires careful planning to maximise recovery whilst operating with the pit design boundaries.Grade control packages are custom designed to reflect the orientation of the footwall and hanging wall mineralisation. The shear material in the footwall zone dips between 60° and 70° and requires angled drilling whereas the footwall mineralisation is contained in shallow dipping quartz veins sub parallel to bedding and can be vertically drilled to best intercept the mineralisation. Ore excavation is directed so that the contact between the footwall and hanging wall is mined in the correct direction so that any non-visual ore contacts can be safely mined and that the ore-waste dilution is reduced.The ongoing grade control and selective mining of the Globe Progress deposit continues to deliver high grade ore for processing by ensuring that waste and dilution of ore is reduced and that recovery is maximised.

Aug 22, 2011

Jan 1, 2004

By E M. Gama, L Resende

The tailings are waste from mineral processing operations. The type of tailings of iron ore processing are classified into sandy tailings and mud. Already the overburden are showing significant levels of useful mineral. Both iron ore`s waste have in your composition phyllosilicates/clay that indicates the potential for use in niche markets as paving and cement. According to several studies, there are various technologies in bench and pilot levels that could be used on a large scale but there is not an economic environment, tax, regulatory and tax set. Many of these technologies are associated with the reuse of tailings and overburden in construction. All these factors influence for that so many initiatives remain in search formats and cannot advance to the new business format. There is no way to set goals of reuse of this waste, as already occurs in China, if there is not a fiscal, tax and economic structure to support such measures. The way to foster and ensure that reuse of tailings and overburden is an incentive for promoting a culture of circular economy that would allow the emergence of an ecosystem between the private, public and Government sectors with the objective of accelerating and subsidize the entire network of reuse of this waste. The closure of the mine could be the tool used to ensure and boost this ecosystem of reutilization to align it with the vocation of the area of the mining law. Following this model, the end of the mining activity could provide a financial return to the local population, a more effective environmental compensation and a reduction in costs related to the closure of the mine. In this study are shown how the Vale is working in the reuse of tailings and overburden.CITATION:Resende, L and Gama, E M, 2018. The challenges of the reuse of tailings and overburden, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 117–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C Bonini, A Markham, P Whittle, B Pearson

"Mine-derived sedimentation in rivers can have significant impacts on the processes and features of the receiving environment and impact on communities reliant on this environment. However, identifying and quantifying the contribution of mine-derived sediment to the receiving environment can be complex. This is particularly the case in remote environments and where little/no baseline assessments have been undertaken. One approach that can be used involves sediment fingerprinting, whereby a unique tracer is identified within the mine-derived sediment to discriminate between mine- and non-mine derived sediment sources downstream. The technique typically involves sampling of sediment at upstream, control and impact sites and sites within the mine deposit. Laboratory analyses are run on all the samples to determine whether the chemical signature (eg presence/concentration of specific metals) differs between each group of samples. In complex environments where the mine-derived signature may be difficult to detect from a basic review of the data, or where sampling constraints may limit the number of samples for analyses, statistical methods can be used to help identify sediment groups. This paper provides a mine case study to show how such an assessment can be undertaken despite the logistical challenges faced while working in remote environments.CITATION:Pearson, B, Markham, A, Bonini, C and Whittle, P, 2013. Fingerprinting and signatures - tracing mine impacts in complex aquatic systems, in Proceedings Water in Mining 2013, pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By S Leichliter

La Colosa, Colombia is a large gold-porphyry deposit currently undergoing feasibility studies by AngloGold Ashanti. This period of development allows the opportunity to apply innovative and emerging testing and modelling methods to provide a predictive geometallurgical recovery model for the deposit. By partnering with the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) research project, the geological and mineralogical data are analysed with respect to liberation and recovery methods. This will allow the variability in the geology and mineralogy of the deposit and key relationships recognised in the data to be included in the development of a model to help predict recoveries of the gold. Many aspects of the gold mineralisation such as gold paragenesis, associations, grain size and texture are determined and analysed using optical microscopy, Mineral Liberation Analysis (MLA), and laser ablation (LA-ICP-MS). At La Colosa the gold has been located in sulfides (eg pyrite, pyrrhotite, and chalcopyrite), silicates, along silicate phase boundaries, and among the pyrite-rich intermediate argillic alteration. Further testing and analysis will also determine if ‘invisible’ gold is present in the pyrite, pyrrhotite, and chalcopyrite. Recovery methods can also be determined and tested after combining the results of mineralogy tests with other data (eg results of comminution tests). Indices for the mineralisation and recovery are developed using image analysis and analytical testing. These indices are correlated with recovery data from the company to develop a predictive block model for recovery. The goal is to develop cost-effective, efficient methods to analyse the mineralogy and geology of the deposit; understand the variability in the mineralogy, geology, and recovery; and construct a predictive geometallurgical recovery model.

Sep 5, 2011

By Huleatt M, Perkin D, McLeod I, Mock C, Pratt R, Gourlay A, Timoney E, Knight N, Ward J

Generally speaking, Australia's reserves of its more important minerals (in terms of export earnings) are adequate to sustain forecast rates of production to the year 2000. The rate of forecast production increases of these commodities (aluminium - whether as bauxite, alumina or metal, black coal, iron ore and ferro-alloy minerals, base metals, tin, uranium, and mineral sands) reflects a well- ordered and sustained growth phase of Australia's mineral industry.

Jan 1, 1981