Search Documents

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

By B E. Hall, J Poniewierski, A J. Hills

Following a review of life-of-asset work at MMG’s Rosebery mine in which a proposal to increase production from 0.8 Mt/a to 1.2 Mt/a was mooted, questions were raised as to the seemingly arbitrary reasoning for the production increase. They included: Did the proposal actually add value? Was the production rate from the mine sustainable? Was it the best identifiable value-adding configuration?A multiple scenario analysis study commenced to model how various cut-off grade values against mill throughput, along with associated capital expenditure, would impact on the potential value of the operation. This was carried out utilising the ‘hill of value’ approach promoted by AMC Consultants.The traditional approach to these studies uses a constant cut-off value (NSR – net smelter return) for the whole mine analysis. This was thought to potentially introduce a large amount of variability to the model as different ore types were thought to have different processing costs and different underground lenses were thought to have different mining costs. With the aim of developing a consistent value measure that would be comparable between the lenses, an alternative measure was suggested for all ore block values in this model, irrespective of lens location.The new measure used was a mine variable value (MVV). This allowed for the variable factors of final metal concentrate production to be removed from the ore value. From a mining point this was the haulage distance from ore source to run-of-mine (ROM). For the mill it was the amount of reagents required, varying based on grade together with the amount of power required for crushing, grinding and tailings handling.From the initial run of the model, preliminary results lead to a conclusion of increased value being gained by either increasing cut-off grade or increased mill throughput rate. The validity of the result was tested using alternative price scenarios, which although changed the absolute value achieved did not significantly change the identified value-adding strategies. The realisation of these value increases identified are however contingent on higher sustainable development rates being able to be achieved mine-wide, higher backfilling rates being able to be achieved and overcoming recognised ventilation constraints. Further detailed studies are being put in place to identify the practicality of overcoming these recognised constraints and achieving the higher-value strategies identified.The ongoing objective of the hill of value model built is to keep the model alive as a life-of-asset planning tool and to continue refining the foundation data, such that various mining strategies can be analysed with increased confidence.CITATION:Hills, A J, Hall, B E and Poniewierski, J, 2014. Mining scenario analysis and mine variable value, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By M Morey

Ok Tedi Mine is located eighteen kilometers from the Irian Jaya border in the Star Mountains, Western Province, Papua New Guinea. Sequential flotation concentrators produce a copper / gold concentrate for market, and a pyrite concentrate for environmental containment, with low sulphur tailings from the pyrite flotation sequence being discharged to river. Strict sulphur assay targets are set for the riverine discharge. Current porphyry and skarn ore blends from open pit operations at Mt. Fubilan will cease by 2017. However, drill cores indicate an economic ore body in the skarn ores surrounding and below the current pit limits. With proposed mining from a western pit wall ‘cut back’ and an eastern pit wall underground operation, potential for ore ageing in sub level cave underground stockpiles is apparent. With little information in the literature, Ore Ageing test work at prefeasibility level consisted of multiple one tonne stockpiles of -50 mm crushed rock. For the bankable feasibility study, a successful test work program was implemented utilizing 40 tonne ROM ore stockpiles composed of exposed pit extensions of future ores. Realistic ageing profiles of Skarn ores were obtained from one tonne monthly samples subjected to laboratory testing. Test work outcomes included:• Similar ore ageing profiles from both the pre feasibility study (PFS) and feasibility study (FS) programs, suggesting ore susceptibility to oxidation has greater effect in ore ageing than rock size for Ok Tedi skarns. • Laboratory rougher flotation of pyrite showed significant variation in sulphur recovery rate, suggesting three classes of pyrite floatability.• Laboratory rougher flotation of both copper and pyrite for up to 19 months ore ageing from 11 stockpiles, suggested three stages in the ore ageing process.

Aug 8, 2011

By S Kost, R Nievergelt, F Cortes

In recent years, the use of steel fibre-reinforced concrete (SFRC) for segmental tunnel linings has become increasingly popular due to numerous advantages including durability, resistance to spalling, reduced cracking at corners and edges and significant cost-saving potential. One of the key parameters for measuring the performance of SFRC is the residual (post crack) flexural strength. A problem often faced in design and quality control of SFRC is the high variability of results obtained by standard beam test methods, with reported coefficients of variability (CoV) in the order of 25 per cent. The high test variability results in a relatively low permissible design strength relative to the average flexural strength of the material and commonly leads to non-conformances with respect to residual flexural strength during production testing.This paper presents the implementation of an alternative testing method using large round determinate panels (RDPs) for quality control testing of the SFRC used in the segmental lining of the City East Cable Tunnel (CECT) in Sydney. The alternative RDP test method was found to correlate well with standard beam tests and significantly reduce the variability of test results, minimising the risk of outlying residual flexural strength results, with zero non-compliant test results reported during the production period.This successful implementation of an alternative test for post-crack flexural strength with lower variability in results constitutes a relevant precedent to demonstrate the feasibility of this approach which contributes to the development of more cost-effective concrete mixes and minimises the risk for non-compliant results and the contractual disputes that commonly arise from these.CITATION:Cortes, F, Nievergelt, R and Kost, S, 2014. Development of a segmental lining specification for steel fibre reinforced concrete flexural strength testing using round panel tests, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 461–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A J. Morrison, K Demir, J Kohmuench, K Runge, C Evans

The Eriez HydroFloat® is a flotation device capable of recovering significantly coarser and lessliberated particles than is possible using a conventional mechanical flotation cell. Originally developed for industrial and bulk mineral beneficiation, the HydroFloat® is attracting increasing interest as a means of increasing the required grind size for metalliferous ore flotation. Doing so would reduce the costs of processing complex ores, either by decreasing the energy required to grind the flotation feed or by increasing the throughput achievable with a given comminution circuit. Processing coarser particles would also result in coarser waste streams, potentially improving the mechanical and hydraulic performance of the waste dams that they are sent to. Recent work at pilot – and industrial-scale has proven the potential of the HydroFloat® technology to achieve these gains in metalliferous applications. However, in order to realise the full potential of the HydroFloat® technology, it is necessary to understand not just its performance but also the drivers for that performance. Doing so will allow the design and operation of HydroFloat® devices to be optimised for different ores and applications. For this work, a HydroFloat® pilot rig was deployed to a coppergold plant in Australia and was used to investigate the effect of stream and operating conditions for treating the tailings stream of one of the plant’s rougher flotation cells. Under each set of operating conditions, samples were taken of the HydroFloat® feed, tailings and concentrate streams, and processed to yield the grade and recovery achieved by the device. At the same time, the bubble size and bed behaviour inside the device were measured. This paper presents preliminary relationships observed between the operating conditions and the performance of the HydroFloat® cell, and thus suggests a range of possible drivers for the measured coarse particle flotation performance.

Aug 24, 2022

By S Q. Liu, E Kozan

This paper proposes a new multiresource multistage scheduling problem for optimising the open pit drilling, blasting and excavating operations under equipment capacity constraints. The flow process is analysed based on the real-life data from an Australian iron ore mine site. The objective of the model is to maximise the throughput and minimise the total idle times of equipment at each stage. The following comprehensive mining attributes and constraints have been considered: types of equipment; operating capacities of equipment; ready times of equipment; speeds of equipment; block-sequence-dependent movement times of equipment; equipment-assignment-dependent operation times of blocks; distances between each pair of blocks; due windows of blocks; material properties of blocks; swell factors of blocks; and slope requirements of blocks. It is formulated by mixed integer programming and solved by ILOG-CPLEX optimiser. The proposed model is validated with extensive computational experiments to improve mine production efficiency at the operational level. The model also provides an intelligent decision support tool to account for the availability and usage of equipment units for drilling, blasting and excavating stages.CITATION:Kozan, E and Liu, S Q, 2014. An Open pit multistage mine production scheduling model for drilling, blasting and excavating operations, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 329–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M Russ, J Gediga

This paper shows an economic feasible approach to implement greenhouse gas (GHG) reduction measures into the mining and metallurgy industry (MMI). The goal to improve energy consumption is directly linked to the reduction of GHG emissions in the MMI. A baseline scenario of the considered reference system and of the respective reference year has to be designed and analysed. In a second step an analysis of the same operation using the best available technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified gaps will be reported and the potential GHG emission reductions will be put into relation to the investment, running cost and generated carbon credits of the new process technologies to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap decision-making for implementing new technology into the companyÆs business operations. The GHG reduction roadmap is developed using the marginal abatement curve approach.

Jan 1, 2009

By Fickera M. A, Marshall S, Burgeese F. L, Burgees J, Estrina H

A new high intensity flotation process FASTFLOT was deployed to recover residual zinc from the zinc circuit tailings at Pasminco Mining's Concentrator, Broken Hill. Performance of the FASTFLOT process is discussed with respect to various size fractions. Results suggest that the process has an affinity not only for fine particles but also for +200 ¦m particles which the conventional flotation cells failed to recover. Various strategies for FASTFLOT deployment are also discussed.

Jan 1, 1995

By M Robertson

3D photogrammetry is a powerful tool for data capture and interpretation, utilised at all Australian underground MMG sites. In personnel constrained mines, 3D photogrammetry can free up personnel time, improve data quality for resource modelling, as well as benefit other mining departments.At Rosebery one of the challenges faced by geologists was no longer data capture but, rather, avoiding paralysis by analysis from the sheer abundance of information currently available to the department. Although the data had been interpreted, the structural model was cluttered; the geological block model was not incorporating any geological domains captured by 3D photogrammetry, nor was it being utilised by other departments such as geotechnical engineering.The geology department is now focusing on utilising all the interpreted data gained from each photograph heading into an uncluttered, easily understandable model for geologists and other mining departments.Our solutions involve integrating the Leapfrog modelling suite into the process, streamlining the structural model, tailoring the data interpretations for future updates of the block model and training other departments to improve utilisation of the interpreted data. This process also uncovered other benefits for near-mine exploration, and improving our understanding of the deposit’s origin.CITATION:Robertson, M, 2017. The practical use of underground 3D photogrammetry data at MMG Rosebery polymetallic mine, Tasmania, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 409–412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By R Barritt

Remedial options for a waste rock dump (WRD) were considered as part of closure planning studies at an active mine in Western Australia. To minimise the impact of any seepage from the landform it was determined that placement cover system utilising the moisture ‘store-and-release’ concept was appropriate. The purpose of the cover system was to:•Reduce net infiltration of meteoric water to attenuate peak concentrations for contaminants of concern in natural receptors to levels that can be assimilated without adverse impact to the surrounding ecosystem; •Provide a growth medium for establishment of a sustainable vegetation canopy; and •Improve current quality of surface water runoff from waste storage areas.The project comprised several phases of work: materials characterisation, numerical soil-plant-atmosphere (SPA) modelling and finally cover system construction and monitoring equipment installation.CITATION:Barritt, R, 2018. Conclusions from long-term cover system performance monitoring – a case study, in Proceedings Life-of-Mine 2018, pp 101–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B P. Micke

Central Norseman Gold Corporation was established in 1935 and has been mining on the Norseman field in Western Australia since then. It is Australia’s longest continuously operating gold mining operation at nearly 80 years, although it has had its periodic challenges in the intervening years.Over the last 40 years, a series of open pit mines around the Dundas Goldfield have supplied lower cost mill feed to the Phoenix Mill at Norseman from time to time but this has largely come to an end for the foreseeable future. Now that underground ore sources are once again the principal mill feed, there are several challenges to be met for an ongoing profitable operation.During the last 20 years, there have been three different owners and this has affected the manner in which the operations were managed quite significantly. These differing approaches are contrasted and examined in some detail from both the operational and financial aspects.Planning of a downsized operation to ensure sustainable profitability in the future in a mining environment where there has rarely been more than two to four years of reserves ahead of the mill for planning purposes has been a significant challenge. Several of the options examined are described, including alternatives for future mine development.CITATION:Micke, B P, 2014. Managing the margin at Norseman, Western Australia – a case study, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 119–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

LKAB operates two underground mines in Kiruna and Malmberget, Sweden. Blast furnace pellet is the main product and makes up 70 per cent of total production. The orebodies are hosted by 1910 - 1860 Ma old volcanic rocks. The host rocks and the ores were affected by the Svecokarelian orogeny for 1890 - 1860 Ma ago. The deposit belongs to the Kiruna type apatite-rich iron ore. Magnetite is the main ore mineral but haematite is the dominant ore mineral in some orebodies in the western part of the deposit. Large-scale sublevel caving is the dominant mining method. Three main haulage levels are in operation at present. The ore boundaries and quality can be detected by geophysical logging resulting in reduced waste dilution and subsequent grade reduction. The susceptibility measurements have been used in the magnetite ore since 1991 and gamma-gamma measurements in the haematite ore since 1998. The mining scale has increased during the last 20 years but diamond drilling has remained at approximately 18 000 drilling metres per year. Uncertainties in the ore constructions can lead to unexpected cost increases, ore loss and dilution. The ore boundaries are evaluated with percussion drill holes using in-hole geophysics to achieve satisfactory geological knowledge. The probes are calibrated in all currently mined orebodies. The correlation between core sample assays and measured susceptibility and gamma-gamma values is strong. The cost to determine the ore boundary by percussion drilling with in-hole geophysics is two-thirds lower, and productivity is six times higher compared to diamond drilling. The measurements are made by geotechnicians and the interpretations by a geologist. The results are transferred to a database and presented three dimensionally as holes with iron grade intervals on mine maps. The interpreted holes are used by the geologist in various ways in the geological modelling. Layout planning uses the measurements as a tool to place the drifts at the correct distance from the ore contact especially in the longitudinal sublevel caving and the production hole planning to optimise the final length of the cross-cuts and drifts for best ore recovery.

Jan 1, 2006

By G Clarke

Commissioning of the Cannington processing plant began in October 1997. The nameplate capacity (of 1.55 million tonnes of ore per annum) was achieved relatively quickly. Since then (like many mines) the operation has strived to increase throughput and improve valuable metal recoveries, to offset declining head grades and lift the value of the operation. The processing plant now has the capability of treating over 3.2 million tonnes of ore per annum and in financial year 2005/06 the combined concentrate production exceeded 600 000 wet tonnes, approximately 80 per cent above concentrate output in the first full year of operation (at the design feed rate). This improved performance was achieved by making changes and additions to each of the major unit processes û primary grinding, flotation, leaching, filtering and paste fill preparation. The changes have included: adding a fines flotation circuit, expanding the grinding circuit, adding a pebble crusher, switching from continuous to batch leaching, building paste conveyors and decommissioning the column flotation cleaning circuits. This paper reviews these changes, outlines the current operating practices and discusses the challenges or opportunities that remain.

Jan 1, 2007

Dimension stone is the term generally given to rock used in building construction. During early European history in Otago, locally available dimension stone products were easily obtained. Crude rock shelters built on river banks with schist rock within Central Otago soon gave way to more established and sophisticated permanent homesteads constructed with the same materials. Victorian architectural achievement is celebrated in Otago with many fine bluestone block buildings. When the University Council decided to build substantially in stone, it narrowly escaped disaster. It was well known at the time that brick in Dunedin was of an inferior quality and that it soon wasted. Rev Dr Stuart said before the 1879 Commission that æthe Council had some old-world notions and liked to have the University with some architectural styleÆ. Contemporary utilisation of dimension stone is generally restricted by expense to a simple veneer. Stone products produced from Otago quarries have found ready markets in other areas in New Zealand , particularly prior to the share market crash in 1987.

Jan 1, 1992

By Falbo A, Barbaro M, Esposito MA, Passariello B

Acidic reductive leaching is one of the best known and most widely employed chemical processes for beneficiating minerals of industrial interest. Conventional acidic leaching with sodium dithionite (Na2S2O4), employed to bleach industrial minerals used in the production of ceramics, glassware, paper etc, does not always allow products of high quality to be obtained. In the work reported here two reducing agents, ascorbic acid and oxalic acid, have been employed in a medium acidified by means of sulphuric acid. Continuous systematic tests have been performed on a kaolin sample containing 0.8 per cent Fe2O3, adopting various operating parameters such as, leaching time, temperature and reagent concentration. In each case the total quantity of bi- and trivalent iron dissolved was ascertained. Removal of 80 per cent and 100 per cent of iron with ascorbic and oxalic acid respectively was obtained, while less than one per cent of iron was dissolved in the presence of sulphuric acid only. Products having a very good degree of whiteness (92 - 94 per cent) were obtained, whereas with sodium dithionite the degree of whiteness was in the 85 to 88 per cent range. The best conditions identified were applied to a sample of quartz for the removal of ferric impurities.

Jan 1, 1993

By J Butler, N Patel, S Narendranathan, S Rastogi

The Yallourn Mine (YM) commenced mining of brown coal in the 1920s under operation by the State Electricity Commission of Victoria (SECV), prior to it becoming privatised in 1996. The present owners of the YM, Energy Australia Yallourn (EAY), acquired the site in 2000 and intend to continue operations until scheduled closure in 2028. Brown coal extracted from the YM is fed into the Yallourn Power Station which supplies approximately 22 per cent of Victoria’s electricity. Water within the YM is collected and stored in the Township Field Fire Service Pond. Water levels within the Fire Service Pond (FSP) may fluctuate considerably depending on the requirement for storage at the site. With due consideration to the stability performance of mine batters adjoining the FSP, the authors performed slope stability assessments to evaluate the risk and consequence of batter instability during the potential pond filling as it approaches the ‘critical pool’. The critical pond is defined as the level at which the driving forces (destabilising forces) are at their greatest and the resisting forces (lake forces, friction) are at their lowest. This assessment was undertaken using the Mine Geotechnical Risk Index (MGRI) approach.

Aug 2, 2023

Throughout the study phases (scoping, prefeasibility and feasibility) of new mining projects one is forced to work with and make predictions based upon limited date obtained from diamond and reverse circulation drill holes. These data are extrapolated to determine how much of the valuable metal is present in the ground, how it can be recovered it and the efficiency of this recovery. Mining methods to extract the ore are investigated with forecasts made regarding excavation stoping stability and performance in an attempt to optimise production. Extraction and use of rock mass data for use in characterising the mechanical behaviour of the rock mass is no exception. One often relies heavily upon the use of empirical charts developed over many years on hundreds of case histories based upon rock mass characterisation schemes. This is largely successful and indicative of what one might expect. However specific site characteristics can always play a significant role, and are not necessarily apparent in diamond drill core. Feasibility studies for the Favona orebodies indicated that the rock mass was generally poor to extremely poor, and that stoping conditions would be difficult in all of the orebodies for various reasons. A range stope performances were achieved ranging from very good to very poor and in some cases unexpected results were achieved. A comparison is made between what was actually achieved and what was expected since stoping commenced in 2007. Explanations are attempted for differences in stoping performance and, in some cases, unexpected results at the Favona underground mine are attempted.

Nov 25, 2010

By S Wellink, D Chalmers, D Adermann, C Martin

The practice of recording blasts for quality control purposes has been conducted for several decades. However, at the low frame rates of a standard video camera, essential data is frequently missed as it occurs when the shutter is closed between frames.The use of high-speed video for the research, development and monitoring of the performance of blasting procedures is a well proven but under-utilised practice.The recent development of low cost, easy to use high-speed digital cameras and user friendly software can deliver a capability into mine management as a day-to-day production tool that can greatly improve blasting performance and reduce costs.Digital high-speed video and image analysis software can accurately quantify each blast. Analysis of the images can facilitate the identification of causes of variance from design, geology changes, errors in blast practice and areas of poor performance. The use of high-speed video greatly enhances the audit and review processes so that future blast design can be quickly and appropriately modified to deliver improved blasting performance and reduced costs.The three videos demonstrate the differences between standard video and high-speed video and the detail that can be obtained from them. These videos of open cut blasts can be used to identify blast performance variances. Capturing images at 1000 frames per second allows the analysis on a millisecond timescale where detonator timings, fragmentation, venting, fume generation and flyrock can be accurately identified.CITATION:Adermann, D, Chalmers, D, Martin, C and Wellink, S, 2015. High-speed video – an essential blasting tool, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 471–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M I. Pownceby

High temperature roasting studies on chrome-spinel contaminated ilmenite concentrates showed that sulfur, introduced through a sulfidising roast treatment, selectively reacted with the chromium in the spinels. The roast treatments were carried out in a laboratory scale rotating drum kiln using a standard Becher-style heating profile (10 h, 1075ºC), char as the reductant, and variable amounts of added elemental sulfur (0 - 3 wt per cent).After roasting, bronze-coloured grains were visible representing chrome-spinels that had undergone selective sulfidisation. SEM imaging of the products showed that sulfur was preferentially concentrated in ~5 - 15 µm thick rims fully enclosing the chrome-spinel grains. The sulfur-rich rims became a sink for manganese (Mn) from the ilmenite resulting in the rims being rich in Cr-Mn-Fe-sulfides. Quantitative electron probe microanalysis of phases present within the rims identified two sulfide phases. The first sulfur-phase (S-phase) was low in Mn (1 - 3 wt per cent) and high in Fe, Cr and S, while the second S-phase was considerably higher in Mn (30 - 35 wt per cent Mn) and lower in Fe and Cr. The dramatic change in the composition of the chrome spinels after sulfidisation is likely to significantly alter their physical properties (eg hydrophobicity, conductivity, etc). This should make their physical separation from the ilmenite potentially easier than roasting/magnetic separation methods.

Oct 5, 2011