Search Documents

By D Kilkenny

Underground contractors in the mining industry must be prepared to take a position at the forefront of innovation of equipment and work methods in order to maintain a competitive advantage over in-house operations and remain relevant. Innovative concepts such as split-feed development jumbos, high capacity trucks and loader guidance systems were implemented by contractors to stay ahead of ‘the pack’. All of these are now common across the industry.The demands of regular participation in competitive tendering coupled with aggressive fleet depreciation, means contractors tend to have more communication and opportunities to work with equipment suppliers than mine owners. Therefore, they are more likely to influence equipment design and product directions. They also have a unique opportunity to assist in trialling new concepts and technologies across a wide variety of operating conditions rather than being restricted to one mine.In addition, as a ‘guest’ on a mine site, mining contractors do not have the luxury of creating the environment for their preferred systems, rather they must have the capacity to adapt their technology to suit the offered environment at a particular mine. This leads to a pursuit of adaptive technologies that can be implemented selectively and seamlessly without excessive disturbance rather than ‘all-of-mine’ systems. These incremental innovations then become available for use across the mining industry where they can add value as ‘bolt-on systems’ to existing operations.Mining contractors, therefore, act as the bellwether for industry practices and equipment. However, in order to maintain their position they must engage industry stakeholders to deliver practical, innovative and cost-effective technologies that add value and result in an improved bottom line for all. This paper uses case study material to illustrate how the Byrnecut Group has approached innovation and how the theory of Disruptive Technology applies to underground mining innovation.CITATION:Kilkenny, D, 2017. Innovation in mining – a contractor’s role, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 59–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Central to any business is its Asset Management Plan which encapsulates the business context and key organisational objectives such as profitability, safety and environmental standards. Life Cycle Planning (LCP) is a key component of an overall Asset Management Plan. A comprehensive approach to Life Cycle Planning forecasts the financial expenditure required to support the performance of the asset over the business life. It incorporates capital, maintenance and operational expenditure along with an estimation of economic life. Within its body the LCP provides the detail of the maintenance plan and method of its execution. Once optimised the LCP becomes the overarching plan executed through the application of several elements of the Asset Management Plan to ensure the return on investment from the assets is optimal. Each of the elements of the LCP is bound by a set of loops that provide information based on the analysis of outcomes. These loops drive the continuous improvement of performance and cost over the life of the asset. In this way we ensure that the LCP is a dynamic plan responsive to the changing business environment. The paper being presented today will describe the process undertaken and the outcomes derived when this approach was applied to a $600 M+ coal handling and preparation plant in QueenslandÆs Bowen Basin. It will also delve into the difficulties encountered from both technical and cultural aspects; the latter proving to be the most difficult to manage. It will describe the hurdles and barriers that hampered progress including the human influences and the natural desire to revert to what has been done in the past when things became a bit difficult. In the end the results are there to show that the upfront expenditure and investment in time was time and money well spent and the outcome has the operation well placed to manage the assets in a manner designed to deliver the optimal business outcome.

Jan 1, 2007

By J Jackson, D C. Curry, A C. Keith

Australian Bureau of Statistics (ABS) data shows that since 2006 the balance of capital costs associated with mine development has become weighted greater than 75 per cent to enabling infrastructure and less than 25 per cent on process plant, equipment and machinery. The well-developed mine planning techniques including pit optimisation and scheduling and process plant design and optimisation have typically proceeded in a linear fashion from geology, mine planning, through processing, with some iterations back to the mine. Only then is attention paid to planning and costing of enabling infrastructure in any detail.Optimisation has typically involved developing cut-off grades, mine plans and schedules and ore processing that produces maximum economic ore. Infrastructure has then been sized æto suitÆ the mining and processing core business drivers.What the ABS data, together with global trends, indicates is that infrastructure can no longer be an afterthought if miners wish to achieve robust project value estimates, realistic ore to market costing and resource statements based on achievable economic cut-off grades.In addition, with such a large proportion of the costs originating from non-mining or processing activities, a mining operation can only be truly optimal if these aspects are given due consideration in the mine design stages, based on quality geometallurgical inputs so that the size and cost of enabling infrastructure is optimised to maximise project value.This paper outlines an iterative holistic approach to mining project development, which integrates the geometallurgical approach and enables infrastructure planning into project design and evaluation. It presents case studies showing reduced overall costs, increased net present value (NPV) and reduced project delivery timelines.CITATION:Curry, D C, Keith, A C and Jackson, J, 2013. Is a 2.5 per cent success rate good enough? Traditional mine development methods have the tail wagging the dog, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 113-128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By D Laskovski, T Nguyen

Flotation surveying can be an extremely powerful means of determining opportunities for circuit optimisation and benchmarking. The type of survey employed depends heavily on the nature of the information required from the survey. It follows then that the type of survey determines the type of samples required; however, regardless of the type, the success or failure of a survey is often dependent on the correct used of appropriate sampling techniques at each sampling point. For a successful flotation plant survey it is vital that the correct samples be collected at the correct time in respect to the feed and each other. This paper discusses the current best practice sampling methods used in flotation surveying and discusses in detail the ideal sample masses based on theoretical analysis. Comparisons with JKTech’s database of real plant operations will then be made.CITATION:Laskovski, D and Nguyen, T, 2014. An investigation of current flotation survey sampling, in Proceedings Sampling 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Q Shu, T Deng, B Yan, B Song, D Wang

In view of the lack of phase equilibria data of vanadium-bearing oxide system and the desirability of them for design or optimisation of vanadium extraction process, the phase equilibria relationships of V2O3-FeO-SiO2-CaO(15 mass per cent) system were determined experimentally and then an isothermal section phase diagram of this system was constructed. Totally, 81 samples of different composition were equilibrated at 1623 K for 48 hours in iron crucible under Ar atmosphere. The equilibrated samples were quenched quickly in cold water, and then the phase constituents of all the samples were identified by X-ray diffraction (XRD) combined with electron probe microanalysis (EPMA) measurements.

Aug 21, 2024

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022

By J M. F Clout

The Roy Hill Project is an independent integrated port, rail and mine development in the Pilbara region of Western Australia. The bankable feasibility study for the project was completed in January 2011 by Roy Hill Holdings Pty Ltd, a wholly owned subsidiary of Hancock Prospecting Pty Ltd. The Project will deliver 55 Mt/a of premium quality iron ore to a rapidly growing market with a mine life of over 27 years. This study is based on exploiting a 1.2 Bt bedded resource of microplaty haematite-rich Marra Mamba, from which 562 Mt of reserves has been delineated to date. A further 1.1 Bt resource of detritals and low grade bedded is proposed to be mined once the bedded high grade resource is depleted. Roy Hill lump and fi ne ore products will compete strongly with other Pilbara products. As a low cost producer, Roy Hill is on track to capture four per cent of the global seaborne traded iron ore market. The project decision to proceed is targeted for Q2 2011 to enable first ore on ship by Q2 2014.

Jul 11, 2011

By H Benzer, N A. Aydogan

It is well known that the high pressure grinding rolls (HPGR) can only be operated efficiently under choke feeding conditions in which a material bed is built up between the rollers to ensure interparticle breakage. By increasing the fines amount in the material bed up to a specific level with the recycling load, a uniform material bed is created and higher pressure gradient along the roller width is obtained which results in compact flakes including more fines. Extensive test work has been carried out with an industrial HPGR unit grinding cement clinker in a cement plant in Turkey. During the test work the recycling load of the circuit was changed to achieve different ratios to the fresh feed rate in order to identify the effect of the recycling load on the circuit performance. Six different tests were performed with the circuit at steady state. For each test, samples were collected from HPGR fresh feed and discharge, and total feed, then the particle size distributions of the samples were determined and mass balances around the circuit were calculated. The conclusion was that the reduction ratio of the HPGR increased with increase in recycling load. The flake densities showed the same trend with more compacted flakes being produced for higher recycling loads.

Jan 1, 2009

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By T Purvis, J Calverd, A-K Greve

The Ernest Henry Mining (EHM) underground mine is situated adjacent to the Great Artesian Basin in North Queensland and within a fracture zone. Underground development commenced in February 2008 and has extended to approximately 1000 vertical metres below the surface.Groundwater has been encountered in numerous locations throughout the mine, predominantly on the eastern side of the orebody and often related to fault structures. Most of the groundwater encountered has been managed with conventional pumping systems; however, on occasions large water inflows have been encountered, which have had a significant impact on the planned development of the mine. Some of the intersections encountered had the potential to compromise the mine from a combination of high temperature (over 45°C), high pressure (3500 kPa) and high flows (50–100 L/s).This paper describes three case studies where significant water inflows were encountered and then controlled by the injection of cementitious grout into the rock mass. The case studies are the 1650 mid-shaft heading, the 1325 shaft access decline and the 1625 to 1475 fresh air rise (FAR) raise bore. Each case study includes a brief description of the event that occurred and the grouting equipment and techniques developed to enable mining to continue.The paper also describes the development of a hydrogeological map of the mine, the probe-hole regime used for high-risk headings and the required processes and systems to inject both cementitious grouts and polyurethane resin into the rock mass.CITATION:Purvis, T, Calverd, J and Greve, A-K, 2014. Management of high-pressure groundwater in underground development at Ernest Henry Mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 217–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By S Utili, A Agosti

The Overall Slope Angle (OSA) of pitwalls plays a crucial role in the financial return of an open pit mine. In current practice, pitwall profiles are designed to be planar in cross-section within each rock layer, ie the profile inclination across each layer tends to be constant. A new slope design software, OptimalSlope, has been recently proposed to determine the geotechnically optimal profile shapes for the pitwalls of mines. OptimalSlope seeks the solution of a mathematical optimisation problem where the overall steepness of the pitwall to be designed is maximised for an assigned stratigraphy, rock properties (unit weight and strength) and Factor of Safety. The geometry of the benches is provided as input to OptimalSlope. The results obtained so far on three mine case studies in isotropic rock masses (Utili et al, 2022; Agosti et al, 2021a, 2021b) show that optimal profiles are up to 5° steeper than their planar counterparts – ie the planar profiles exhibiting the same FoS – leading to realising significant saving on waste rock and as a consequence Net Present Value increments and carbon footprint reductions. OptimalSlope algorithms have been modified to deal with anisotropic rock masses characterised by direction dependent shear strength. In the paper, the case of rock masses in banded iron formations (BIF) is tackled. A data set of anisotropic rock shear strengths typical of Western Australia is considered. The Snowden modified nonlinear model was employed to characterise the anisotropy of the rock mass shear strength. From the OptimalSlope simulations performed emerges that optimal pitwall profiles can increase significantly the Overall Slope Angle in comparison with planar profiles featured by the same Factor of Safety. LEM stability analyses of all the profiles were also performed by Rocscience Slide 2 to independently verify the FoSs of the optimal profiles obtained.

Nov 29, 2022

By T P. Medhurst

In many cases mine design is the most important driver of the profitability of a mining project, however to reach an æoptimumÆ mine plan many compromises have to be made. Some of the fundamental profit (and loss) drivers relate to stoping methods and stope design parameters. Inevitably trade-offs have to be made between the stability of underground openings, ground support costs and production efficiency. This paper looks at the role of geomechanics in the mine planning and design process. The concepts of æcontrollable lossesÆ and æuncontrollable lossesÆ are developed as a means of partitioning ground control costs. A stope design example is given which provides a method of examining mining costs, and includes a decision making element in order to quantify geotechnical impacts and select stope dimensions. The method also provides a general framework as a means of balancing ground control costs against maximising returns from an underground mining project.

Jan 1, 2000

By B W. Ham

The legacy of underground coal mining may be a land surface which, in parts, may be unstable in the long term. A case study analysis has been undertaken to explain some of the hazards and how the risk may be assessed and managed.The Ipswich Coal Measures were extensively mined with shallow underground workings, which now underlie a number of suburbs in the eastern side of the city of Ipswich in south eastern Queensland. The area was subject to underground mining from the 1840s to 1997. In general, the mines were small, family-owned operations that were restricted by complex geology, interactions with neighbouring operations and ownership of surface facilities. The oldest available mine plans date back to the late 1890s.The residents in these mining areas have a long history of unexpected mining subsidence events. A level of risk management for property owners has been implemented by the Ipswich City Council, which requires a mining subsidence risk assessment to be submitted as part of building applications for property development in the areas suspected of having mining subsidence risk. This discussion examines a series of generic subsidence events and how the risk may be assessed and managed and the hazard controlled.CITATION:Ham, B?W, 2014. The legacy of underground coal mining – mine subsidence: Ipswich coal measures case study, in Proceedings Life-of-Mine 2014 , pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By Bure R

Approximately 2.4 million ounces of gold and 11.3 million ounces of silver have been produced from the Umuna Lode by Misima Mines Pty Limited between June 1989 and the end of Decemeber 1996. Reserves remaining at the end of December were 32.1 million tonnes at 1.0 gram per tonne gold and 9.7 grams per tonne silver. To attain precious metal production of this volume, an estimated K60,000,000 (1996 Kina) was spent on exploration alone. from the 1940s to the present day. Exploration expenditure for the 1996 calendar year was approximately K4,400,000. With such a large investment in exploration, large quantities of data were generated and stored in various forms. To make best use of this data, it was necessary to organise and systematically store this data in a form compatible with a modern Geographical Information System (GIS). The Umuna Lode on Misima Island is a low sulphidation gold- silver deposit dated at 3.5 ¦ 0.2 Ma. The deposit is controlled by the 50 to 100 metre wide Umuna Fault- a moderate dipping, brecciated clay- chlorite- carbonate altered, normal fault zone. There is approximately 230 metres of mostly dip slip offset on this fault, which is measurable by the offset of the Cretaceous schist, marble and greenstone host sequence. Late Miocene microdiorite spatially related to the Umuna Lode does not appear to be genetically related to the gold- silver mineralisation. GIS was introduced to Misima at the end of 1995 and until recently has been mostly used for data storage and retrieval, the over- laying of various data sets to assist in targeting prospective areas, and as a drafting tool. The use of data-driven, predictive data analysis is the most recent effort in maximising the use of the extensive Misima database. By characterising the key controls and properties of the Umuna- type mineralisation, a Weights of Evidence, data-driven analysis produced a prospectivity map of Misima Island. The purpose of this map was to identify prospective areas yet to be explored and to assess the effectiveness of exploration to date.

Jan 1, 1997

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Widzyk-Capehart, T Bednarz, O Daud, N Cutmore

The interest of industry, in particular future mining, is pointing towards the use of novel visualisation systems to improve the operational efficiency of user interfaces. While the technologies used to enhance operators’ experience are advancing, the implementation of novel visualisation paradigms within mining operations is trailing behind other industries, particularly health and aviation. In this work, we present a number of initiatives and use cases of immersive virtual and augmented reality systems that can fit within the mining context. These ideas represent a step towards new platforms that might increase the efficiency and safety of mining operations through applications such as 3D panoramic video monitoring technology with annotated information coming from big data analytics and visual analytics processing engines. However, while the technologies are used in a variety of training settings, their application in the working environment is lagging behind. This paper presents examples of scientific visualisations that could be applied in a mining context to extend the possibilities of operators’ cognitive abilities and working efficiency. They are intended to foster a discussion within the mining community to move beyond the training realm and into the operational environment.CITATION:Bednarz, T, Widzyk-Capehart, E, Daud, O and Cutmore, N, 2015. Effective immersive visualisation systems for mining applications and beyond, in Proceedings Third International Future Mining Conference, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By H Dehghan Jan Abadi, K Shahriar

The iron ore district of Gol-e-Gohar (GEG) is located 60 km south-west of the city of Sirjan, in the Kerman Province of the Islamic Republic of Iran. Six exploration targets have been identified and iron ore has been mined from one area with dry and wet concentrate products sold. Prior to mining commencing in 1999, the proven reserves were estimated at 265 million tonnes (Mt) in 2004 and 40 Mt of 100 Mt overburden has since been mined. Of the six exploration targets, the largest anomaly in the GEG district is Deposit No 3. This paper discusses economic considerations focusing on mine extraction and construction of a concentration and pelletising plant to process ore from Deposit No 3 of GEG. Planned capacity of 10 Mt product (concentrate and pellet) per year is targeted to commence in 2011, and nominal capacity by 2014. The economical evaluation and analysis is one of the most important stages in the feasibility study of mine development. Financial calculations including the provision of financial resources, operation period revenue, loss and profit statement, cash flow, net cash flow, internal rate of return and net present value have been undertaken as part of the feasibility study. The feasibility study operating plan assumes a large open pit mine containing proven reserves of approximately 250 Mt. The feasibility study assumed an economic return of $80 per tonne iron pellet. The economic study determined that Deposit No 3 of GEG can be economically developed by open pit mining followed by magnetite separation and flotation to generate iron concentrate and pellets.

Jan 1, 2007

Two key elements in the design of a pastefill or high density hackfill system are the preparation of the backfill material and its distribution underground. This paper examines these two areas. Owing to the essentially impervious nature of total mill tailings, preparation of pastefill and high density fill from current tailings involves a physical dewatering process. There are currently three methods available for this process: I. Vacuum or pressure filters. These represent the 'traditional' approach to the preparation of pastefill. 2. Paste production storage mechanism. This is a thickening/storage mechanism developed with the specific objective of producing paste/high density backfills. 3. Fluidization. This system utilises silos fitted with simple dewatering devices and nozzles. Recently developed by CANMET, it provides the simplest and most economical approach. This paper describes and compares the three preparation methods, from a practical and an economic point of view. Once the pastefill/high density fill has been prepared and binder added, the backfill must be distributed underground into the stopes. A fundamental factor in the design of a distribution system is the rheology of the material- No two materials will exhibit the same properties, and a sequence of rheological and related testing is required prior to the completion of the design of the underground distribution system. This paper covers the testwork normally required and discusses the fundamental design parameters of pastefill distribution systems. The final section of this paper summarises the use of pastefill at three mincsin Canada.

Jan 1, 1998

By S Kowalczuk, S V. L Barrett

The potential for adverse surface settlement during tunnelling in soil and rock poses a significant risk to the successful completion of any tunnelling project. Undesirable ground movement may lead to unacceptable level of damage to surface infrastructure, buildings and the environment, resulting in safety concerns as well as causing significant delays and costs to a project. One of the empirical methods which is commonly used to predict surface settlement in the early stages of a project’s development is the volume loss approach as described by Mair, Taylor and Burland, 1996. This method was developed for use in soft ground; however it has also been applied in weathered and soft rock to provide an initial indication of potential surface settlements along a proposed tunnel alignment. This paper presents some initial thoughts on the use of this method in weathered and soft rock and the associated limitations which need to be taken into consideration when interpreting the results. This includes complex weathering profile cases where the strength and stiffness of the ground does not necessarily increase with depth.CITATION:Kowalczuk, S and Barrett, S V L, 2014. Initial thoughts on application of the volume loss approach for estimates of surface settlement due to tunnelling in weathered rock, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 641–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014