Search Documents

By Pollard D. M

The BHAS copper-lead matte leach process, developed in Port Pirie, South Australia, has been in operation on a commercial scale since 1984. This process is one of many developed in the past decade to recover copper via the hydrometallurgical route. In essence, the process involves a single stage agitative leach of 100% -75um matte in an acid chloride-sulphate lixiviant with gaseous oxygen as oxidant. The leach temperature is controlled at 85¦C to assist with reaction kinetics. After leaching, divalent copper is recovered from solution via a conventional solvent extraction/electrowinning circuit to yield cathode copper for sale The BHAS matte leach process has several unique characteristics cf. other commercial oxidative acid leach processes. These include i) the use of gaseous 02 as oxidant ii) H2SO4 addition as make up acid iii) Relatively low chloride ion addition (30 g/1) For this reason, extensive work was carried out into the optimization of leaching by Meadows (1985). Variables investigated included ò Oxygen flow-rate ò Agitation intensity ò Leach temperature ò Free acidity ò Chloride ion concentration ò Matte particle size The current work was conducted to determine the effect of cooling rate, and hence mineralogy, on the leaching characteristics.

Jan 1, 1989

By P Holtham, K C. Runge, E Tabosa

Traditionally, comminution and flotation have been surveyed, analysed and optimised separately. This often results in less than optimal outcomes because of the complex interactions between the two processes. Flotation recovery is a strong function of the valuable mineral particle size distribution with lower recovery of ultra-fines due to poor flotation kinetics, optimum recovery for the intermediate sized particles and lower recovery for the coarser particles due to poorer liberation. Thus, to optimise flotation recovery and grade it is usually best to grind to a fine size. This requirement needs to be balanced by the cost of grinding finer and the revenue that results from an increase in grinding throughput, which often results in a coarsening of the flotation feed.This paper demonstrates a technique which can be used to predict the effect of a change in feed grind size on flotation performance. It can be used to determine the optimum grind size for a particular operation which optimises total circuit profitability. Analysis is relatively easy to perform, as a minimum, requiring only size by assay data of the feed and product streams of the process. Case studies will be presented that demonstrate the usefulness of this technique in feed grind applications. Potential use of the technique for regrind evaluation is discussed. The limitations associated with this technique in certain circuit scenarios will also be outlined.CITATION:Runge, K C, Tabosa, E and Holtham, P, 2014. Integrated optimisation of grinding and flotation circuits, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By P Luo, J E. Danoczi, P Nakutnyy

Sensor-based sorting methods to remove waste or for upgrading ore prior to downstream metallurgical processing is becoming more prevalent for mining operations. X-ray transmission (XRT) sorters are a popular choice for mineral processing plants since they can sort a wide variety of minerals. XRT sorters pass high intensity X-rays through particles to generate images of varying greyscale, based on their effective atomic density. The ore sorter then mechanically separates the particles using algorithms based on the images. A popular test currently used to evaluate the amenability of the ore to XRT sorting is to pass the particles through the sorter and obtain the greyscale images showing mineralogical differences. This test provides information on the mineralogical heterogeneity between ore particles for their separation. However, it does not provide an understanding of the actual mineralogical composition of the ore or information pertaining to which other minerals may respond in a similar manner, nor does it provide liberation information. This paper describes a test that combines high resolution X-ray micro Computer Tomography (CT) combined with QEMScan to obtain information about amenability of ore to XRT sorting and to obtain valuable information that can streamline metallurgical testwork programs. This test also provides information relating to particle thickness and associated X-ray attenuation coefficients, desired mineral presence and mineralogical information relating to associated minerals and clays to assist with developing sorting algorithms. Combining the CT and QEMScan can address many limitations of the current method to determine whether XRT sorting technology is appropriate for particular ores. Mineralogy information from QEMScan can identify incidences of; mineral encapsulation, problematic clays, detrimental minerals as well as calibrate the greyscale values of CT data. Additional 3D CT imaging carried out on cores provides spatial information of the minerals within the ore and mineral grades.

Nov 10, 2020

By R Chinamatira

Several technical and economic factors have to be taken into consideration in developing an optimal mining method. This paper describes some of the important factors learnt during the evolution of the sublevel cave mining method at Trojan Nickel Mine, part of the Bindura Nickel Corporation (BNC) in Zimbabwe. Sublevel caving (SLC) has been successfully implemented at Trojan mine since its introduction in 1994. The method has evolved over the past six years into a system that has brought about improvements in efficiencies and productivity. Although the original design parameters used were sound and provided a solid foundation for the system, they needed to be optimised to get the best out of the mining method. Improvements and changes have been made in areas such as the drilling process, charging and blasting techniques, ring pattern design, development size and shape, and the draw control system. This has enabled the mine to develop an SLC operation that is efficient and innovative. Experience gained, together with the theory available has given us a much better understanding of the system. This knowledge will be used in the future to enhance the system further. Given the low grades of the BNC Mines, management recognises that only through technical excellence and efficient mining can the mines reduce mining costs and maintain profitability and competitiveness on the world market. In the Zimbabwe mining industry reaction to technological change, mechanisation and advancement have been relatively slow, due to isolation and economic constraints, compared to the rest of the world. Economic difficulties prevail, with high inflation levels, a poor exchange rate, lack of foreign currency and other associated problems. Despite these constraints, the bold steps taken have transformed Trojan mine into a more efficient and competitive operation, presenting itself as the leading mine in the BNC group. Appendices give data to illustrate the benefits obtained.

Jan 1, 2000

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002

By J Wheeler

The objective of this paper is to examine the operation of high frequency screens in closed circuit grinding, where the outcomes achieved indicate favourable economic gains at the comminution stage and downstream processes, including flotation, dewatering, and filtration operations. The classification process in grinding circuits has been slowly evolving within the last century. The history of classification devices brings to mind rake classifiers and spiral classifiers, which although having higher efficiencies compared to hydrocyclones, were not able to keep pace with the evolution of concentrator equipment treating higher tonnages. This higher tonnage throughput has tended to drive the concept of utilising hydrocyclones as the classification stage in closed grinding circuits. The comminution process is commonly the most energy intensive stage of mineral processing. Researchers have determined that the classification stage in the comminution process has the greatest potential for improvement. This paper is intended to inform mineral process engineers of the benefits that high frequency screens offer over hydrocyclones. This will be done by reviewing the purpose for the evolution of classification in the comminution process, documenting past and recent studies, and explaining the modern technology that is currently available.

Aug 8, 2011

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011

By D Atheis, S Williams, A Dance, D Taplin

"Resurrected from its former life at the Big Bell operation, the grinding circuit at Evolution Mining’s Edna May operation in Western Australia has many a story to tell. The task of optimising a plant designed for another orebody provides as many challenges as opportunities. Initially faced with a blend of primary and oxide ore, the circuit achieved in excess of 320 t/h until the oxide was depleted, leaving only the much harder primary feed.The 2.0 MW semi-autogenous grinding (SAG) mill and 3.7 MW ball mill were assisted by a 150 kW pebble crusher, but the power limitation of the SAG mill resulted in a drop in throughput. Edna May personnel have been involved in a number of progressive improvements to restore the design capacity of the concentrator and work towards 3 Mt/a or even higher ahead of the gravity and leach recovery circuits.These improvements include: a crush forward configuration of the SAG mill scats partial to full secondary crushing variable speed drive upgrade of the SAG mill lifter and grate design changes ball mill circuit grinding efficiency.This paper summarises the chronology of events that has resulted in significant improvements in throughput by conventional (and in some cases, novel) methods of reconfiguring the existing grinding mills. Lessons learned and hindsight perspectives will be summarised, sharing this educational experience with other operations in a similar situation.CITATION:Dance, A, Atheis, D, Williams, S and Taplin, D, 2014. Grinding circuit improvements at Evolution Mining’s Edna May operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 63–70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By L Dyer, A Keith, G D. Corder

As mining activity moves to remote and less developed locations globally, a holistic approach to mine development is fundamental for achieving a balance between strong financial returns and corporate social responsibility and transparency. Key inter-related fundamentals such as social licence to operate, life-of-mine operational planning, minimising environmental impacts and, most importantly, attractive investment returns for the mining company all contribute to the viability of any new mining project.However, the typical practice in the mining industry is often to treat environmental and social/community aspects as separate compliance issues that are dealt with at minimum cost and disruption to the project and resulting operation. This often results in less than optimum environmental and social outcomes, and presents considerable liabilities at the time of closure when rehabilitation programs continue to require funding when all revenue has ceased.The five capitals model seeks to identify each of the key contributors to sustainable development as financial, manufactured/physical, social, human and natural to formulate a type of triple bottom line approach balancing these often competing project factors. The SUSOP® sustainability risks and opportunities framework, developed by the mining industry, bases its approach on the five capitals model and proposes an approach that breaks down enterprise silos to identify innovative solutions for life-of-mine sustainability. This framework has been developed with the nature of mining projects in mind in order to produce approaches and outcomes relevant throughout the life cycle from the planning phases, through project design and construction into operation and closure.This paper argues the need for a more holistic approach to the development and operation of mining projects, and presents case studies where a holistic approach has been applied, in whole or part, and discusses the lessons learned from these case studies.CITATION:Corder, G D, Keith, A and Dyer, L, 2014. A capitals based approach – leading innovation in planning for life-of-mine sustainability, in Proceedings Life-of-Mine 2014, pp 499–512 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By P Fuller, A R. Penney

Re-commencement of mining in the Western Zone of Beaconsfield Gold Mine following a seismically-induced rockfall fatality in April 2006 required a change of mining method involving drilling and blasting from specially developed drives in the footwall of the orebody. Broken ore is mucked remotely from ore drives on each level. Support in the footwall drives is required to maintain stability during their development and as stopes are retreated, which increases induced stresses and further seismic events are triggered. The paper outlines the challenges involved and methods used to select the footwall drive support to handle both static and dynamic load demand. The importance of load development in the support system, its displacement capacity, the compatibility of support elements and energy absorption capacity of the support system are highlighted. It is usual in any support selection process to ensure that capacity exceeds demand to create a factor of safety. In this case the demands on the system relate to load, displacement and energy absorption and the support system capacity for each must ensure that appropriate factors of safety for each are achieved. The paper shows how these factors are not independent and that selecting a high factor of safety for load can lead to compatibility problems with support elements in the support system.

Jan 1, 2008

By C Jenkins, M Mativenga, C Stanton, J Gerber

In 2014, Arrium completed an optimisation program on its magnetite concentrator, enabling a reduction in the overall cost base of producing concentrate through an increased ability to treat a wider range of ore types, previously considered waste. The development was the culmination of four years of work, conducted in house by Arrium’s mining development group. The overall intent of the plant design focused on improving the concentrator’s ability to treat a wider range of magnetite ore types. Metallurgical analysis of these feed ore groups outlined a need for more grinding power if production quality was to be maintained and throughput increased. As such, a tertiary grinding circuit was designed which, alongside the rectification of key operational bottlenecks, would allow the plant to continue to produce concentrate at the required specification and rate. The technology chosen for the tertiary grinding application was the XT IsaMillTM, which is known for efficient fine grinding when compared to conventional ball milling. The transfer sizes between the existing comminution circuits were coarsened, allowed for the treatment of different ores at the required rates. The optimisation project was successfully completed in February 2014 after a three month commissioning phase. The initial metallurgical testing and engineering of new equipment proved highly successful with all equipment meeting or exceeding design parameters.CITATION:Stanton, C, Mativenga, M, Gerber, J and Jenkins, C, 2015. Unlocking plant capability through targeted debottlenecking of Arrium’s magnetite concentrator, in Proceedings Iron Ore 2015, pp 185–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By C J. Greet, S Jacques

In most instances, the application of high-chrome grinding media results in an increase in the recovery of the valuable mineral(s). The authors have published data from a number of plant-based case studies, which indicate that it is not unreasonable to expect a recovery increase in the vicinity of 1.5 to 2.0 per cent for a copper ore. It is of interest to understand where the increase in recovery is coming from. That is, is the additional copper recovery the result of improved fine particle flotation or is it due to an improvement across all size fractions?This paper aims to answer this question. Laboratory flotation tests were completed using forged steel and a high-chrome alloy on a volcanogenic massive sulfide copper ore. The unsized data indicated that the application of high-chrome grinding media to this ore resulted in an improvement in both copper recovery and copper concentrate grade. A detailed kinetic analysis of both the copper sulfide and gangue minerals was completed that clearly shows that the change to a more inert grinding media produced significant increases in the flotation rate constants (both fast and slow) across all size fractions. It is also possible to observe that the change in pulp chemistry has resulted in a decrease in the flotation kinetics of the -20 micron pyrite, while the coarse pyrite recoveries have increased, presumably because of an increase in the flotation of the chalcopyrite/pyrite composite particles.CITATION:Greet, C J, Jacques, S and Kinal, J, 2014. Recovery-by-size kinetic analysis to determine where metallurgical improvements occur when converting to high-chrome grinding media, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L Mariano

Three selected iron ore samples from the major bedded and channel iron deposits of Western Australia were analysed using a scratch test commonly used in the oil and gas industry. The portable commercial equipment dubbed Wombat cuts a groove on the surface of the sample with a cutter under imposed depth of cut and cutting velocity. The normal and tangential components of the force acting on the cutter are recorded with a high degree of precision (about 1N) at fine spatial resolution of about 20 measurements per millimeter.The intrinsic specific energy inferred from the scratch test measurements is found very well correlated with a classical measure of strength such as the uniaxial compressive strength, for over 300 sedimentary rock samples.The results obtained on the iron ore samples are comparable to those obtained on oil and gas sedimentary rocks. This method could provide an objective and semi-automated measurement of material strength and brittleness in iron ores that can possibly be correlated to the lump to fines ratio.

Jul 11, 2011

By G Harbort

Traditional engineering design for flotation circuits use the “Rule of Thumb” approach. Typically this uses a nominated maximum head grade for design. A scale-up factor is applied to laboratory flotation tests for residence time. This scale-up factor is usually based on a designers experience at other flotation sites and may or may not be relevant to the circuit being designed, or the flotation equipment being used. A small number of locked cycle tests are assumed to represent the ore body and the results of these are often used for financial analysis, independent of changes in mine plan throughput and mineralogy.The engineering “Rule of Thumb” approach is only strictly accurate where there is very little variability in throughput, head grade and mineralogy. It may provide accurate design for mature established operations where a brownfield expansion is being considered but is unlikely to provide accurate design for a new, greenfield site.The use of geometallurgical modeling with floatability component simulation provides a design methodology with significantly less associated risk. The use of geological data for optimisation of operating plants has become a significant part of the modern process mindset. The underlying principle is to use spatial metallurgical information to drive production planning, mine planning, blast design, blending strategies and plant set-up. At a design stage the process designer can use geometallurgical information to evaluate bottle necks and potential design flaws and propose the best investment strategy for the project benefit.This paper details the geometallurgical characterisation of the Andash deposit and methodology used to review the project’s detail design and projected production.

Aug 8, 2011

By L Nicholls, A Parbhakar-Fox

Reprocessing Queensland’s historical copper tailings for critical minerals is an opportunity to circularise the state’s mining industry by converting waste liabilities into assets. Mine waste valorisation enables economic rehabilitation of legacy mining sites, improves environmental outcomes, and can establish a secondary resources sector that produces a sustainable supply of critical minerals to supplement growing global demands (Australian Government, 2023). The North-West Queensland Minerals Province (NWQMP) hosts numerous copper mines with known cobalt mineralisation (Degeling, 2020). Cobalt is a critical metal essential for green energy and battery technologies, however its global supply is at risk due to geopolitical and ethical concerns (Rachidi et al, 2021). Historically mining in the NWQMP has focused on copper, leaving cobalt to theoretically accumulate in the mine waste. First-pass geometallurgical characterisation of waste repositories by the Sustainable Minerals Institute identified Capricorn Copper as a key site for further investigation into cobalt deportment and recovery potential.

Aug 2, 2023

By A Tsang, D La Rosa, L Julian, W Hunt, R Pratama

Mineral extraction is facing the twin challenges of finite resources and increasing environmental and economic costs. Society’s growth is matched by an increase in demand for the earth’s resources. It is incumbent on us as contemporary mining professionals to promote and facilitate ethical and efficient practices. Technological developments have and will continue to allow a decrease in viable cut-off grades, creating new economic opportunities from deposits that were previously uneconomic. Mining low-grade deposits however, even with perfect recoveries, will have a significant environmental cost for the metal won. The greatest opportunity to increase metal with the least environmental cost is to increase the metal yield from existing mines. The determination of mining polygons is a critical juncture where rock is typically subjected to the binary grading of either ore or waste. This is undertaken using a number of factors, such as the mining equipment being used and the recovery in the processing plant. Traditionally, mining polygons were generated on the in situ grade control model. This ignores the complex differential blast dynamics that occur during blasting. Two opportunities exist to improve metal yields: optimise the blast design to achieve the post-blast muck pile that will support the greatest outcome; and generate optimised polygons on the post-blast muck pile. A data set from a Canadian Gold deposit is used to demonstrate the potential benefit of iterative blast movement modelling and grade control polygon optimisation on metal yield. The impact of blasting on the total recoverable metal is presented, highlighting blast design as a critical process in the mining value chain.

Sep 1, 2024

By G Capes

A novel open stope design approach is presented that delivered improved performance in a mining area with poor ground conditions at the Olympic Dam mine. During 2019, a large open stope had an unplanned caving event resulting in the inability to extract the planned tonnes and subsequent sterilisation of nearby stopes. A design limitation was the lack of data and understanding around the alteration domain extents, the rock mass strength controls and limits, the failure modes controlling stope stability in the local area, and the use of conventional stope shapes. From the available data and failure observations, it was inferred that the dominant caving failure mode resulted from a blocky rock mass impacted by structure and alteration causing an unravelling failure mechanism. Numerical and empirical analyses were conducted to test this hypothesis and establish strength limits for design. The strength limits for the design were then used to provide a range of outcomes from which future stope design shapes such as chamfered backs could be selected. Three alternate chamfered geometries were selected to trial the innovative designs. The application of this methodology in 2020 resulted in overbreak reduction from >100 per cent in the initial caved stope to

Mar 29, 2023

By W Zeng, D Walker, D Cai, E Baafi

"The efficiency of the truck-shovel haulage system is significantly influenced by the truck fleet size. A discrete event simulation model with 3D animation has been developed to estimate the productivity of a truck-shovel network system, shovel efficiency, truck cycle time, truck utilisation and the optimal fleet size. The simulation model considers the dynamic variability of traffic conditions and also the truck as an individual entity. The resulting truck cycle time was found to be realistic and thus providing a better tool for strategic mine planning.Citation:Zeng, W, Baafi, E, Walker, D and Cai, D, 2016. A 3D Discrete Event Simulation Model of a Truck-shovel Network System, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 265–273 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By G J. Showers, P Botman, A G. Hunt

Iron Road Limited (Iron Road) is currently evaluating the feasibility of producing 21.5 Mt/a of high-grade (>66 per cent Fe) magnetite concentrate from a 3.7 Bt resource (JORC) located at Warramboo on the central Eyre Peninsula in South Australia. Bulk concentrate can be produced via a conventional grind and low-intensity magnetic separation flow sheet. Due to the comparatively coarse magnetite liberation size (106 µm), consideration was given to enhancing both the grind economics and coarser product sizing via gravity separation.This paper outlines the test work, flow sheet design and engineering design of a gravity beneficiation circuit (GBC) conducted by Mineral Technologies for Iron Road. The resulting circuit optimisation necessitated mass balance simulation by Iron Road’s SysCAD model to quantify the resulting changes in mill recirculation load. This included the determination of project-critical grinding power and energy requirements with and without the GBC installed into the primary ball mill classification circuit. The outcome of this work was the design of a GBC, including spirals and up-current classification, which led to a substantial reduction (33 per cent) in ball mill recirculating load and power requirements, together with a favourable coarsening of final product size due to the relatively coarser gravity concentrate. This has led to a significant reduction in project design capital and operating costs. A further benefit of this approach is increased recovery of (paramagnetic) hematite and lesser titano-hematite via gravity separation compared to an all-magnetic separation approach.CITATION:Hunt, A G, Showers, G J and Botman, P, 2015. Test work and design of a gravity circuit for Iron Road’s Central Eyre Iron Project, in Proceedings Iron Ore 2015, pp 139–142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E Jak, J Chen, B Hogg, S Nikolic, S Nicol

The quantity of post-consumer ‘waste’ materials generated each year is rapidly increasing. These materials can contain significant quantities of critical metals and present an environmental challenge if landfilled. The ISACYCLE™ technology is a proven solution for the processing of these materials. In the ISACYCLE™ furnace, the post-consumer materials are processed to recover energy along with any contained critical metals, in the form of a base metal alloy or matte. In addition, a clean aggregate (slag) is generated, which has the potential to be used for a range of applications in the construction industry. This slag is commonly based on a fayalite slag but is modified to manage the complex feed. This paper will review the fayalite slag system and the theoretical modifications required for treating urban wastes. Slags from an ISACYCLE™ furnace processing urban wastes have been sampled and characterised. The chemistry of these samples will be reviewed and compared to the expected theoretical modifications required.

Jun 19, 2024