Search Documents

By L Mollison, K W. Mills, N R. P Baczynski, M F. Lee, I A. de Bruyn

This is the first of two papers concerned with rock stress inputs to various mine design issues at the large Ok Tedi open pit mine in Papua New Guinea. The companion paper (also published at this conference) is ‘The Application of Rock Stress Inputs to Stability Assessments at Ok Tedi Mine, Papua New Guinea’ (de Bruyn et al, 2014).Stresses are a required input for numerical modelling of mine design issues. However, for some operations, like the very large Ok Tedi open pit mine in remote rugged mountainous terrain, direct and representative measurement of rock stresses can be technically difficult and expensive. In such situations, development of an appropriate and sufficient understanding of rock stresses can be challenging.This was addressed for Ok Tedi by considering the following:The tectonic and regional geologic setting of the mine.Results from three different programs of rock stress measurement over 19 years, including hydraulic fracturing (1991), acoustic emission (2007) and overcoring (2010). Some interesting results of the overcoring work are discussed. It was done in a 4 km long drainage tunnel, which intersected a thick monzodiorite intrusive that has metamorphosed contacts to host contact Ieru Formation siltstones; anomalously low horizontal stresses were measured within the monzodiorite.Compilation of rock stress measurements from other New Guinea mines and prospects, both in Papua New Guinea and Indonesian West Papua.Comparisons between the variable Ok Tedi rock stresses and similar data from other porphyry copper deposits.CITATION:Lee, M F, Baczynski, N R P, Mills, K W, de Bruyn, I A and Mollison, L, 2014. Rock stresses at Ok Tedi, Papua New Guinea, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By T Angerer, N H. Maund, S Hagemann, D R. Cowan

Cliffs Natural Resources Pty Ltd - Asia Pacific Iron Ore's (formerly Portman Iron Ore Limited) K deposit (Dowd's Hill), at its Koolyanobbing operation in Western Australia, hosts enriched magnetite mineralisation below the presently mined haematite-goethite ore zone. Two distinct northwest-southeast elongated, highly magnetic anomalous bodies that dip to the north-east appear to be sourced by this deeper mineralisation. Magnetic modelling indicates significant remanent magnetisation with Qratios around 1.5, directed shallow down. The north-west anomaly is overlain by a ridge of uneconomic banded iron formation (BIF) and the present waste dump, whereas the south-east body was partly exposed during ongoing mining of overlying haematite-goethite ore. Sections of the magnetite mineralisation in this south-east anomaly were intersected previously by diamond drill holes. Review of the historic cores identified potential magnetite enrichment, with grades and mineralogy that might be amenable to beneficiation. A first-phase reverse circulation drilling program was designed to further delineate the trend and extent of the two anomalies. The following magnetite mineralisation assemblages are recognised from cores, reverse circulation (RC) drill cuttings and pit mapping of the south-east magnetic body: higher-grade magnetite-haematite ¦ goethite and magnetite ¦ pyrite and lower-grade, recrystallised magnetite-quartz (BIF), magnetite-carbonate, magnetite-talc and minor magnetite-bearing mafic schist. Disseminated specularite is locally present in theassemblages. Talc-schist and massive pyrite occur along the footwall contact. Magnetic susceptibility measured from drill chips within the magnetite-enriched zones reveals an apparent susceptibility values range of 0.2 to 1.3 SI. Preliminary results from Satmagan and Davis tube recovery analysis shows that the magnetite content in these mineralised zones correlate well with existing geophysical data and magnetic susceptibility measurements.

Jan 1, 2009

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

By Umetsu Y, Su Qing-quan

The electrical conductivity of electrolytes is very important in metal electrowinning and electrorefining processes as it has a very large influence on the energy consumption. There are few measurements of the electrical conductivity of zinc electrowinning electrolytes available. The electrical conductivity of zinc electrowinning electrolytes were measured over the following range of concentrations, 100 to 200 g/L H2SO4, 0 to 80 g/L Zn and 0 to 20 g/L Mg, at temperatures from 25 to 60 C. The specific conductivity of zinc electrowinning electrolytes may be expressed as a function of concentrations of sulphuric acid, zinc and magnesium and temperature by the following equation: k(S/cm) = 0.004 + 0.00115 t + 0.00282 [H2SO4] t - 0.00114 [M] t + 0.3442 [H2SO4] - 0.0451 [1-12SO4]2 - 0.1058 [M]ò[H2SO4] - 0.0224 (M] + 0.0286 [M] 2 where t is temperature (C), [H2S04](moI/L) is sulphuric acid concentration and [M](mol/L) is a sum of zinc and magnesium concentrations, ([Zn]+[Mg]). The specific conductivity of zinc electrolytes is a function of the concentrations of the hydrogen ion and free water molecule, which are calculated by taking into account the second ionisation constant of sulphuric acid and the stability- constants of zinc-sulphate and magnesium-sulphate complexes at 25 C.

Jan 1, 1993

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and'reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By J OÆDriscoll, R Butler, L Winter

The iron ore mining district of Labrador West and adjacent Quebec is Canada's largest iron ore producer with almost 50 years of production. The area is currently experiencing a period of renewed activity not seen in decades that includes new mine development, mine expansion and exploration for new iron ore resources. All of the past and present production and exploration programs in the district are centred on the Lower Proterozoic Superior-type iron formations of the Knob Lake Group, located within the Grenville tectonic province of the Canadian Shield. The Knob Lake Group is a continental margin sedimentary sequence which was deformed and subjected to greenschist to upper amphibolite facies metamorphism during the Grenville orogeny. Regional deformation and metamorphism plays a key role in making the iron formation of the Knob Lake Group economic. The distribution of orebodies in the district is controlled by superimposed F1/F2 synclines which causes thickening of the iron formation through repetition. Ore mineralogy consists of specular haematite, magnetite and locally martite with quartz as the major gangue mineral. Regional metamorphism has caused an increase in grain size of the ore minerals making it more amenable to concentrating and pelletising. Altius has been active in Labrador West since 2003 and is now the second largest licence holder in the district with several iron ore exploration projects. The Kamistiatusset project is located in the heart of the region's transportation, power and mining infrastructure. The property has seen limited previous exploration, but covers several significant iron ore prospects. Work by Altius includes a helicopter-borne magnetic survey, ground magnetic and gravity surveys, geological mapping, sampling and 6000 m of diamond core drilling all of which confirm both a favourable geologic setting and ore mineralogy.

Jan 1, 2009

By M R. Dehghan, H Mansouri, A Hakami, M A. Ebrahimi Farsangi, F Faramarzi

Today, it is accepted that rock fragmentation by blasting affects loading and hauling operations, and also directly influences on downstream processes such as crushing and grinding. In this research, the influence of rock fragmentation by blasting on the performance of three mills at Gol-e-Gohar iron ore mine No 1 was studied. Firstly, the fragmentation of conventional blast patterns in iron ore (5 × 6 m) was studied using image analysis and the performances of three mills were monitored. Then, a new blast pattern (4 × 5 m) was designed and nine blasts were carried out using this pattern. Increasing the powder factor form 1650 gr/m3 to 2480 gr/m3 by changing the blast pattern design showed that mill throughputs increase five per cent to 30 per cent for the new pattern.CITATION:Hakami, A, Mansouri, H, Ebrahimi Farsangi, M A, Dehghan, M R and Faramarzi, F, 2015. Study of the effect of blast pattern design on autogenous and semi-autogenous mill throughput at Gol-e-Gohar iron ore mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

By M Orunesu Preiata

The Odysseus Project is part of the high-grade Cosmos Nickel Complex that lies 30 km north of Leinster. The Odysseus definitive feasibility study (DFS) was approved by the Western Areas’ board in October 2018. Early works commenced in January 2019 with rehabilitation of the existing underground infrastructure. In June 2022 Western Areas was acquired by IGO Ltd. The project is now well advanced to meet its target of first concentrate. The project included the construction of a haulage shaft. The design of the hoisting equipment and the shaft barrel evolved from the initial DFS design stage to the final execution, as the data were made available from the initial investigation to the data gathered during execution (although this did not change from its initial concept). The design philosophy for the haulage shaft incorporated, from the beginning a multidisciplinary approach with inputs from three main areas involved in such projects, namely excavation techniques, geotechnical assessments, and infrastructure construction. This interaction is a fundamental component for the success of such a critical project. In fact, each of these three areas influences each other in a cyclical manner, triggering a continuous review of the project inputs and outputs, while maintaining the original project goals: the design of an infrastructure able to deliver the desired throughput. The throughput dictates the infrastructure that needs to be built, which in turn controls the size of the shaft. The key assumption applied to this is that the rock mass can accommodate the excavation void, and the excavation technique with its tolerances and limits that ultimately need to be verified back with the initial assumptions used for the infrastructure design. The aim of the paper is to present a case study of the experience gained with the Odysseus hoisting shaft and to propose a possible logic path for similar projects elsewhere.

Mar 29, 2023

By Anievas JB, Sevillano AC

This paper describes the acquisition, exploration, development, initial operation and subsequent financing of the Bulawan mine by means of a listing on the Toronto Stock Exchange of a subsidiary of the parent company, Philex Mining Corporation.Located on the island of Negros in the Philippines the property is unique on at least two counts: it is a disseminated gold deposit that occurs in a region of predominantly porphyry copper mineralisation; and it is a gold deposit that is mined by a bulk method of extraction (front and block cave) instead of the normal selective mining methods.

Jan 1, 1997

The Kunwarara magnesite deposit is the largest known magnesite (MgCO3) deposit in Australia. It is located under black soil plains to the north of Rockhampton in Queensland. The deposit consists of magnesite nodules set in a fine-grained sandstone, siltstone and mudstone matrix. The magnesite is derived from weathering of serpentinite in adjacent hills and transport of magnesium in solution to a Tertiary/Quaternary river system. The magnesium has come out of solution in the active river system, and combined with atmospheric and biogenic CO2 to form magnesite nodules. The magnesite can be very pure with certain varieties up to 98 per cent MgO (LOI free). The deposit has been mined since 1991 and processed into magnesia (MgO) which is sold into refractory, agricultural and other markets. The geologist is an integral part of the small mine technical team. The role of the geologist includes characterisation of the ore through drilling and bulk sampling, supervision of geological aspects of mining and assistance in the optimisation of ore processing.

Jan 1, 2000

By C D. Rose

"The primary objective of this paper is to demonstrate a different approach to predicting and verifying mechanical sampling system precision. Early in the year 2011 an experiment was conducted to evaluate the sampling precision being obtained by a three-stage falling-stream mechanical sampling system for coal owned and operated by Peabody Energy. This system collects samples from lots averaging approximately 14000 t being loaded onto rail cars at a flow rate averaging about 9000 t/h. In phase 1 of the experiment, a total of 60 increments were collected in a two day period at preassigned intervals using a cross-belt sampler located on a conveyor belt feeding a silo upstream of the sampling system under evaluation. Coal variability parameters were calculated from the resulting laboratory analysis data using the gauge-invariant fractal model developed by the author.Estimates of precision of the three-stage system as a function of the number of increments were calculated using the variability parameters determined in phase 1. In phase 2 of the experiment, duplicate samples of 30 lots of coal were taken by the three-stage sampling system, enabling calculations of the precision being achieved by the system. Phase 2 precision estimates are in reasonable agreement with those of phase 1. Conclusions drawn from the experiment include the following: Experimental variograms or the equivalent correlograms are essential in understanding sampling issues and for designing a sampling system to meet specific precision requirements. Consensus coal sampling standards provided by ISO and ASTM may be improved by treating all stages of a mechanical sampling system as æsamplingÆ rather than considering downstream sampling stages as æsample preparationÆ, to be treated in a separate part of the document. The coal industry would profit from use of methodology for routinely monitoring the overall measurement precision and the precision of the individual components of measurement: sampling, sample preparation and laboratory testing. This would not only give necessary credence to the measurement results but would also no doubt, lead to more efficient sampling system designs.CITATION:Rose, C D, 2012. Evaluation of precision being obtained by a three-stage sampling system for coal, in Proceedings Sampling 2012, pp 115-124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By R Justa Cámara, L M. Pinillos Lorenzana

Barcelona Metro Line 9 (Line 9) is an essential infrastructure, improving the transversal transport in Barcelona by connecting the greater part of the currently existing radial lines. The purpose of Line 9 is to create a peripheral line surrounding the city of 1.6 million people (metropolitan area exceeds five million), and includes 52 stations, of which a total of 32 are deep shafts and 19 transfer stations in a densely populated area with several geographical constraints.The tunnel has an inner diameter of 10.90 m, bored with an earth pressure balance (EPB) tunnel boring machine (TBM) in soil sections with precast concrete lining type universal ring and segments 40 cm thick.A single tunnel solution was adopted, driven by functionality and costs savings. The internal tunnel section is divided into two levels to allow for one way rail transit including the platforms in each station on each level in order to optimise the space created by the TBM excavation and comply with the operational needs. The division in two areas of the tunnel was carried out through the construction of a horizontal slab resting on the tunnel segments with a constant thickness of 40 cm at the central part of the slab and supporting side walls.CITATION:Justa Cámara, R and Pinillos Lorenzana, L M, 2014. Two transit levels in one tunnel tube – an innovation in Barcelona Metro Line 9, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 387–398 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P S. Jaitawat, M Sarim, M P. Roy, P K. Singh, A Joshi

Mining is being carried out using the sublevel open stoping method at the Kayad underground mine. The mine will ultimately reach a depth of 390 m. Kayad village is only 100 m (horizontally) from the underground mining areas. As a result, blast-induced ground vibration is one of the major issues for the residents of the village. This paper deals with the process involved in optimising blast design parameters at the development face blast, slot raise blast and ring hole blast to control blast-induced vibration within safe limits while ensuring improved production, productivity and safety. In total, 1041 development face blasts, 110 slot raise blasts and 52 ring hole blasts were conducted, and 2612 vibration data were monitored in the village at different locations. Initially, electronic delay detonators were used, with an emphasis on controlling vibration in the surface structures. Subsequently, shock tube (Nonel) initiations were used as the blasting faces reached lower depths. A comparative study was also performed for both the initiation systems. The orebody width generally varied from 3.1 to 7 m, and ring hole designs were optimised accordingly. The number of holes in a ring was up to seven and the depth was up to 23 m, depending on the size/width of the orebody. The ring blasts were performed with 64–340 kg of emulsion cartridge explosive and detonated with explosive weight per delay of 10.92–17.16 kg. Extensive experiments were performed and blast-induced vibrations were controlled in the village. Deck blasting (ie up to four explosives decks) was used in a blasthole and the explosive charges were separated by delay detonators, which helped to control the vibration in the village. The actual detonation time of each deck was recorded by monitoring the in-hole velocity of detonation of the explosives, and the charging patterns were optimised accordingly to get the desired blast results.CITATION:Roy, M P, Singh, P K, Sarim, M, Jaitawat, P S and Joshi, A, 2015. Blast design and vibration control at Kayad lead-zinc underground mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 533–544 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By K Barns, H Law, T Whebell, P Scobie, T Perkins, J Siliezar, M Larson

With processing a variety of orebodies at Glencore’s Ernest Henry Mining (EHM) has come a changing mineralogy and more complex requirements for treatment in the concentrator. From mid-2013 and into 2014 the grind size required to achieve sufficient mineral liberation for production of a quality concentrate has reduced significantly. What was once a final P80 of 35–45 microns was forced to 20 microns. This has necessitated some creative changes to the flow sheet that previously had a 937?kW Vertimill regrinding a rougher concentrate to 40 microns. EHM is able to utilise an existing M10 000 3 MW IsaMill previously used for magnetite processing, to provide a quick convenient solution without large scale capital expenditures. Operating the Vertimill and IsaMill in parallel in closed circuit was successful at reducing the P80 of the regrind circuit to below 20 microns which increased the final concentrate grade by four per cent. This circuit and intermediate circuits used are discussed. Performance of the Vertimill and IsaMill is compared for efficiency optimisation to improve the overall circuit performance.CITATION:Siliezar, J, Whebell, T, Perkins, T, Law, H, Scobie, P, Larson, M and Barns, K, 2014. From magnetite to chalcopyrite – a story of versatility and efficiency at Glencore’s Ernest Henry mining?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 85–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By C Rothfuss, X Wang, S J. Herbert, K Prasad

The extraction of groundwater to produce gas from coal seam gas (CSG) reservoirs has highlighted the opportunity for beneficial uses of groundwater in Australia. This paper presents an assessment of alternate groundwater modelling approaches that can be used for assessment of one beneficial use option, that of injection. This assessment examines the outcome of the use of different simulation methods on predictions of hydrodynamic behaviour.In this paper, a simplified hydraulic concept of a multi-aquifer system within the hypothetical injection field was used to investigate the hydrodynamic behaviour of injection into the Precipice Sandstone. Comparisons were made through the analysis of a Theis 3D analytical solution with 2D and 3D numerical solutions. The paper discusses the different solution methods and the impact of these on predictions of pressure and flux. Differences in 2D and 3D solutions result in implications if planning injection as a beneficial use of water. For example, the 2D solution resulted in faster and higher injection pressure build-up when compared to the 3D solutions. The 2D modelling could result in either plans that require higher capital expenditure for a greater number of wells in order to spread the pressure effect and remain below the maximum injection pressure or a reduced injection rate. Meanwhile, the 3D modelling with sensitivity analysis could result in planning for lower capital expenditure for fewer wells required to spread the pressure effect and remain below the maximum injection pressure. CITATION:Wang, X, Herbert, S J,?Rothfuss, C and Prasad, K, 2013. Assessment of effectiveness of artificial recharge for coal seam gas water management based on numerical modelling, in Proceedings Water in Mining 2013 , pp 67-72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Nell, J Petersen, X C. Goso

The feasibility of increasing the deportment of titanium species and the stability of the pseudobrookite solid solution (M3O5) in a titaniferous slag was investigated, to facilitate the valourisation of titaniferous slags. Thermochemical simulations using FactSage™ software, ver 8.3 (by Thermofact/CRTC and GTT-Technologies), and equilibration-quench experiments were conducted using an appropriate synthetic titaniferous slag composition in an oxygen partial pressure (pO2) ranging from air to 10-16 atm under non-isothermal conditions. The temperature-pressure phase stability diagram for the synthetic slag containing 37.19 per cent TiO2, 19.69 per cent SiO2, 13.12 per cent Al2O3, 16.00 per cent CaO and 14.00 per cent MgO showed that the spinel solid solution (M3O4) was the primary phase until a pO2 of 10-10.5 atm, thereafter M3O5 was the primary phase until a pO2 10-13.2 atm. M3O4 again was the primary phase between a pO2 10-13.2 and 10-16 atm. The changeover of the primary phase coincided with an increase in the liquidus surface. When cooling the slag in a pO2 of 10-16 atm, M3O5 crystallised as a ternary phase that showed a rapid increase in mass while that of the primary M3O4 phase decreased and that of the secondary perovskite (CaTiO3) phase increased at a slower rate. At 1300°C under sub-liquidus conditions, the contents of M3O5, M3O4 and CaTiO3 were about 20 per cent, 15 per cent, and 11 per cent, respectively. Experimental results showed that the Ti3+/Ti4+ mass ratio in the M3O5 phase, ie a measure of the reduction of titanium species, is not considerably sensitive to equilibration temperature in the reviewed range. Slow cooling and minimum/no oxidation during cooling of titaniferous slag would increase the deportment of titanium species to, and the growth and stability of the M3O5 phase.

Jun 19, 2024

By D Bertoldi, C Haines

"The Waihi Gold Mine (WGM) operated by OceanaGold New Zealand Limited is a wholly owned subsidiary of the OceanaGold Corporation of Australia. Traditionally WGM has stockpiled and processed separate campaigns of open pit and underground ore. The ore is processed via a conventional semi-autonomous grinding (SAG) / ball circuit (SABC). The low aspect SAG mill operates in a closed circuit with two 20" cyclones, whilst the ball mill is also a closed circuit with a 10" cyclone cluster. A major wall movement in April 2015 ceased open pit operations indefinitely, 18 months ahead of the mining plan. This immediately reduced the forecast mill tonnage leaving two options: begin campaign milling or change the operating strategy and target lower throughput. Additional cost pressures necessitated improved milling cost efficiency. The immediate ore restriction limited processing alternatives to within the existing major infrastructure. Available comminution circuit survey data laid the foundation for developing a comminution model using the JKSimMet™ software package (version 6, created by KJTech). A number of flow sheet variants were then evaluated based on predicted throughput and efficiency. The comminution models suggested opportunities for improved efficiency lay in reducing throughput and increasing utilisation rather than on/off campaign milling under the existing operating philosophy. A series of process alterations followed, delivering new cost efficiencies that maintained the current $/t processing cost. This paper aims to review the change in circuit performance and examine the decisions and challenges faced following the transition from a high tonnage SABC circuit to lower tonnage SABC circuit.Citation:Haines, C and Bertoldi, D, 2016. The Transition from Semi-autogenous to Autogenous Milling at Waihi Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 303–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By A D. Price, W J. Germs, O Patterson, T R. Weaver

"Understanding controls on groundwater and surface water flow and quality at mine sites throughout all mine stages is critical to effectively manage environmental impacts over the entire mine life. Monitoring forms is an essential component of this proof of understanding. Typically, monitoring programs at mine sites have been developed in the framework of existing conditions. However; recognition of the challenges of climate change and the performance of mines during recent extreme events in Australia has highlighted the need to develop monitoring programs that are resilient and responsive to changing environmental conditions. Water monitoring programs need to be effective under a range of environmental conditions, potentially not historically experienced.This emerging challenge requires cross-disciplinary teams to work together to understand issues including: representativeness of background conditions to longer-term conditions at the mine site sensitivity of mine and closure designs to changing climate and hydrologic conditions methods of performance (eg water quality or quantity) failure during extreme climate events such as flood or extended drought.These understandings come together in a detailed conceptual and, in many cases, numerical hydrologic model that considers the mine-water environment under a range of conditions. The groundwater, surface water and water quality monitoring programs that are developed from the conceptual model need to be sufficiently responsive to be effective in the face of such changing conditions, with results in turn informing the conceptual model. Extended drought, major floods and changing weather patterns can alter recharge and discharge areas, oxidation profiles and ultimately, the contaminant flux estimates that would have contributed to mine design parameters and performance. Unless these effects are considered in the spatial and temporal design of the monitoring program and within the parameters monitored, the resultant program may fail to capture data that are critical to evaluating environmental impacts from mine sites.Developing and implementing a water monitoring program that considers these issues can build confidence in mine performance under a range of conditions, leading to increased confidence by all stakeholders in long-term mine performance during and after closure.CITATION:Weaver, T R, Price, A D, Patterson, O and Germs, W J, 2013. Developing resilient water monitoring programs in changing climate conditions, in Proceedings Water in Mining 2013, pp 109-114 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013