Search Documents

By K Saito, M Hasegawa

Removing sulfur and phosphorus from molten iron can be expressed by the following reactions, respectively. [S]Fe + (O2-)slag = (S2-)slag + [O]Fe [P]Fe + (3/2) (O2-)slag + (5/2) (FeO)slag = (PO43-)slag + (5/2) Fe(liquid) These equations indicate that desulfurisation and dephosphorisation have opposite oxygen potential conditions. If a small amount of desulfurisation slag not removed is carried over to dephosphorisation process, the reaction of sulfur mentioned above proceeds toward left hand resulting in increasing sulfur content in molten iron. For better understanding of such re-sulfurisation reaction in hot metal pre-treatments, the present study aimed at evaluating the effect of iron oxide on the sulfur distribution ratio between slag and hot metal. To measure sulfide capacities and FeO activities simultaneously at temperatures below the melting point of pure iron, CaO-SiO2-FeO and CaO-Al2O3-FeO ternary molten slags were brought into equilibria with copper-iron-sulfur liquid alloys, and the equilibrium oxygen partial pressures were determined with an electrochemical technique involving the stabilised zirconia solid electrolyte. The experimental results showed that the sulfide capacity increased with an increase in FeO content, and this trend was consistent with the fact that FeO was basic. Although the addition of FeO raised the FeO activity and oxygen potential, the calculated value for sulfur distribution ratio between slag and hot metal increased with increasing FeO content.

Jun 19, 2024

By I Özen, G Chitumbura

A paper identifying anticipated challenges in the extraction of the N3500 Orebody at Glencore Xstrata Copper’s Mount Isa Copper Operations was written in 2007. The paper identified the depth of the deposit, the anticipated high stresses, talc alteration and issues with ground support as factors that may affect production. A number of strategies were planned to cope with these issues. After six years of extraction those strategies are evaluated and additional measures taken are outlined. Strategies to cope with the limited mine life are presented, and methods to overcome additional challenges encountered during production are described.CITATION:Chitumbura, G, Matthews, D, Özen, I and Jackson, S, 2014. One mile underground – mining the N3500 orebody at Mount Isa Mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 265–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J A. Cowburn

The high intensity zone within the Jameson Cell is the downcomer. It is largely external and separated from the flotation tank. This, together with operation of the downcomer under vacuum, rather than at elevated pressure and the absence of moving parts, allows ready access to the high intensity zone for measurement and analysis. Experimentation was conducted allowing measurements of recovery for residence times of between 20 milliseconds and ten seconds within the downcomer of a Jameson Cell. The affect of aeration rate on the recovery of different particle sizes was also studied.

Jan 1, 2005

By H S. Mitri, A Sainoki

Destress blasting techniques have been widely employed in underground mines for the purpose of preconditioning highly stressed rock mass. Appropriate applications of the technique successfully contribute to increasing mine safety (eg mitigating the risks for rock bursts). This paper presents a simulation technique to estimate the extent of damage zones induced by destress blasting. A 3D numerical model with a single blasthole is constructed with FLAC3D code, whereby static analysis is carried out in which horizontal and vertical stresses are applied to the model in order to simulate stress conditions in a deep underground mine. Afterwards, dynamic analysis is performed whilst applying time-varying blast pressure along the blasthole. The blast pressure profile takes into consideration an instantaneous increase and gradual decrease in blast pressure as well as the propagation of detonation along the blasthole. In this paper, constitutive models allowing for shear and tensile strengths of rock mass that are dependent upon strain rate are newly implemented into FLAC3D code with C++ programming language, whereby blast-induced damage is assessed by the extent of tensile and shear failure zones. The results obtained from the dynamic analysis show significant decrease in the extent of yielding zones induced by destress blasting with increasing the magnitude of in situ stress. They indicate that considering in situ stress state is indispensable in order to propose proper blast design for each level in underground mines. Based on these results, the relationship between the extent of the damage zone and depth at which destress blasting is performed is established. Furthermore, stress dissipation induced by destress blasting is examined with static analyses, in which the modulus of elasticity is decreased according to a rock fragmentation factor, a, only for the area where tensile and shear failures takes place during the dynamic analyses. A model parametrical study with respect to a is undertaken. The relationship between the rock fragmentation factor and the stress dissipation in the yielding zones is developed from the parametrical study. The developed relationship can be useful when destress blasting is designed for massive rock masses.CITATION:Sainoki, A and Mitri, H S, 2015. Simulation of damage zones induced by destress blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 245–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By Bidwell TJ, Servant S

Paste back-fill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste hackfll is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the hackfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in-situ measurement of paste backfill properties.

Jan 1, 1998

Equilibrium in the reaction H2(g) + [%0] (in liquid copper) = H2O (g) was investigated at temperatures between 1200 -and 1350°C with p(H2Oj/p(H2) ratios between 1 to 15. A semi-microbalance was used for direct measurement of dissolved oxygen in molten copper. Oxygen was found to obey Henry's law under the experimental conditions used. The standard free-energy change for the above reaction is given by Equation 1where 1 weight per cent solution is the standard state for dissolved oxygen.For the dissolution of oxygen in copper according to 1/2 O2(g) = [%0] (liq. Cu), the standard free energychange is given byEquation 2.

Jan 1, 1973

The history of the discovery and development of the Kambalda nickel orebody. is reviewed and the decision to process the Kambalda concentrates by the Sherritt-Gordon process at Kwinana is discussed. The Kwinana Nickel Refinery is described and the problems encountered in the first year of operation are Outlined.

Jan 1, 1971

By H Askari-Nasab, E Torkamani, M M. Badiozamani, S P. Upadhyay, M Tabesh

"Decision-making in mining is a challenging task. Optimal decisions regarding shovel and truck allocations, aligned with the optimal short-term production schedules, are crucial in keeping the operations in line with the company’s long-term objectives. In this paper, we present two main modelling components as the means to achieve near-optimal operational plans: a mixed integer linear goal programming model to allocate trucks and shovels to mining faces over a shift-by-shift basis so that operating costs are minimised and resource utilisations are maximised through the planning horizon a discrete-event simulation model to investigate the behaviour of a truck-and-shovel haulage system in the presence of uncertainty within mining operations. The goals integrated into the mathematical model are to: maximise production minimise deviations from the target head grade minimise deviations in tonnage feed to the processing plants from the desired feed minimise operating cost.The mathematical model provides shovel assignments and the target productions as an input to the discrete event simulation model while meeting the desired goals and constraints of the mining operation. We illustrate the applications of the discrete event simulation model by presenting a large-scale oil sands case study. The main contribution of this work thus far is the development, implementation and verification of a simulation model with a link to optimal short-term mine schedule and extraction sequence of mining faces, which assists in achieving a high level of mine plan compliance across short-term planning and operational planning time horizons.CITATION:Askari-Nasab, H, Upadhyay, S P, Torkamani, E, Tabesh, M and Badiozamani, M M, 2014. Simulation optimisation of mine operational plans, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 299–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By A Takahashi, Y Uchisawa, M Hayashi, T Watanabe, M Susa

Owing to the deterioration of iron ore, the Al2O3 concentration in iron ore increases, and thus it is important to investigate the effect of increment in Al2O3 concentration on the microstructures of iron ore sinters. During the sintering process, a melt is present in the sinter for only a few minutes, and therefore the microstructure of the sinter doesn’t reach thermodynamic equilibrium. Nevertheless, the formation process of the microstructures can be interpreted and predicted to some extent from the equilibrium phase diagram. This study investigated the liquidus isotherm in the CaO-SiO2-Fe2O3- 5 mass% Al2O3 system at 1240°C in air and the phase equilibria of silico-ferrite of calcium and aluminium (denoted by SFCA) and SFCA-I by XRD (X-ray diffraction analysis) and electron probe micro analyzer (EPMA). The following results were obtained: 1. The ferrite melt region with a high Fe2O3 concentration shifts to the lower Fe2O3 side than the liquidus isotherm in the CaO-SiO2-Fe2O3 system. 2. The compositional region of SFCA extends in the CaOꞏ3Fe2O3-4CaOꞏ3SiO2 direction than the silico-ferrite of calcium (denoted by SFC) composition region with a 0 mass% Al2O3. 3. SFCA-I is observed in the present system, which suggests that the increment in the Al2O3 concentration contributes to the stability of SFCA-I. These results imply that an increment in Al2O3 concentration in iron ore leads to a decrement in the volume fraction of the bonding phase and that the fraction of the SFCA phase increases, and those of 2CaOꞏSiO2 and slag phases decrease in the bonging phase. The SFCA-I phase is also precipitated from the slag with an Al2O3 concentration around 5 mass%.

Jun 19, 2024

By P Moser, R Ivanova, F Ouchterlony

This paper describes model-scale bench blasts on mortar blocks with distorted drill hole patterns, done in 2013–2014 at the Montanuniversitaet Leoben. The main aim of the project is to see if the fragmentation from and the crack development behind blasts with and without drill hole deviations differ significantly.The dimensions of the test blocks were 660 × 280 × 210 mm (L × W × H). They were mounted inside a yoke that allows the blast waves to escape (see Figure 1). Three rows in each block were shot row by row with a nominal pattern of B × S = 70 × 95 mm. The same nominal delay 73 µs (ie 1 ms per m burden) between holes was used throughout. Blocks with holes of stochastic collar position errors (variations in burden or in burden and spacing but constant row volume) and systematically shifted collar positions (blasts with staggered pattern) were shot. The results were compared to reference blocks without collar deviations.Apart from the sieving analysis, the remaining bench faces were measured with a stereo-photogrammetric method and horizontal roughness profiles for each row were constructed. Sawing slabs from block remains after the third row and use of dye penetrant allowed the study of internal blast damage.The analysis showed that none of the changes in borehole collaring had a significant effect on the sieving curve (median). The sieving results confirm earlier findings though that the fragmentation gets finer with the number of rows shot, implying that blast damage from earlier rows has an influence on the blasting results. The tests demonstrated that the nequiv (equivalent n-value) has increased ten per cent by shooting staggered pattern and decreased by seven per cent by pattern with burden and spacing errors. For the rest of the patterns, the nequiv was roughly the same.The surface roughness investigation showed that a smooth surface was achieved by the staggered pattern. The other deviations patterns did not show a clear trend.The internal blast damage, which was measured in the remaining part of blocks, showed that out of eleven, four crack families seemed to be most affected by blasting. The comparison of the reference and distorted patterns showed that less cracks were apparent for the staggered pattern, ie less damage was introduced.CITATION:Ivanova, R, Ouchterlony, F and Moser, P, 2015. Influence of distorted blasthole patterns on fragmentation as well as roughness of, and blast damage behind, remaining bench face in model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 693–706 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By N Eriksson

BolidenÆs Aitik mine, located 100 km north of the Arctic Circle in northern Sweden, is one of EuropeÆs largest copper mines. This operation produces 18 Mt of ore per year and 99 per cent of this tonnage needs to be deposited as tailings. The tailings pond currently covers 1140 ha but at closure it will hold around 760 Mt of tailings and occupy an area of 1400 ha. The tailings contain less than one per cent sulfur and only 0.03 per cent copper. The carbonate content is as low as 0.25 per cent but silicates, with substantial accumulated buffering and metal adsorption capacity, are abundant. A programme of comprehensive material characterisation and investigations has been undertaken in order to design a decommissioning strategy that meets the regulatory requirements and secures long-term physical and chemical stability of the deposited tailings. The main concern has been the potential generation of acid rock drainage (ARD). Standard tests using acid base accounting (ABA) and humidity cell tests during 15 weeks were not conclusive regarding the ARD generation potential. The accuracy of the results was considered to be unsatisfactory, therefore the humidity cell tests were gradually extended in time. In total, almost four years of humidity cell tests were conducted on various sets of samples which were selected in order to cover the variation in sulfide content existing on site and in various points of the milling process. The laboratory results were subject to detailed geochemical evaluation in order to fully understand the interaction between acid-producing reactions, driven by weathering of sulfides, and acid-consuming reactions by dissolution of carbonates and alumino-silicates. The laboratory tests were followed by both pilot tests and field measurements in order to estimate the scale dependency between the laboratory and the field results. It was found that sulfide weathering rates in the field were considerably lower than those measured in the laboratory. However, it could not be verified that the tailings top layer would maintain a neutral pH in the long term even under field conditions. Thus, a reviewed tailings management plan, including de-pyritisation of the tailings during the last years of operation, is considered.

Jan 1, 2003

Computational models are very useful for studying many of the physical mechanisms which can cause sample bias. Within such models we can predict the trajectories of all individual particles and thereby make observations which are not possible for physical systems. Physical mechanisms highlighted include congestion at the cutter aperture, particles bouncing over the cutter aperture, air drag on fine particles, waves of material being bulldozed off the belt by the upstream side of the body of square cutters, and particles being thrown by the leading edges of cross-belt cutter blades. Having identified relevant physical mechanisms for an existing cutter, we can estimate the extent to which they are likely to result in unequal representation of portions of a stream of material and thereby estimate the maximum likely sample bias.

Mar 1, 2010

FOR some years past it has been usual to specify high-grade copper for use for many purposes, but the practice of specifying zinc of a high degree of purity for certain purposes is of comparatively recent origin. It is a practice, however, which is extending ag the effect of the impurities in zinc on products manufactured therefrom becomes widely recognized.The notes hereunder are intended to briefly survey the principal uses to which high-gr.ade zinc is being put, and, wherever possible, to indicate the effect of the impurities normally present in the lower grades of zinc.In the United States zinc is graded into five divisions, known respectively as "High-grade" "Intermediate" "Brass Special" "Selected," and "Prime Western." The maximum amounts of impurities allowed in the various grades are indicated in Table I,which is compiled from data published by the American Society of Testing Materials:In addition, it is specified in an cases that the slabs shall be reasonably free from surface corrosion or adhering foreign matter. Although zinc used in Europe has in many cases been sold on analysis it is only recently that any attempt has been made to grade...

Jan 1, 1923

A belt of serpentinized ultrabasic rocks intrudes a moderately folded geosynclinal sequence of fine to coarse sediments, acid, intermediate, and basic volcanics as well as a batholithic mass of granitic rocks. The ultrabasic body contains small included masses of melanocratic and leucocratic rocks, together with chromium, copper, zinc, and nickel mineralization.

Jan 1, 1969

By Pati±o A

The Argentine pyroclastic loess arevulcanogenic deposits, which have their sources in the circumnpacific rim. The object of this work is to realize a de-tailed mineralogical characterization of this sediments, to use it like a geo logic outline which regiters discordance or similarity in them, The sampling zone extend from 714N-4125 to 622W-339S. The descriptions of these sediments was considered like basic, mesobasic or acid rocks. The basic sediments, looking like andesite-basaltic composition, are fill-ing the andean valley. The mesobasic one have a similar composition with a pyro-clastic dacite rock, and have been found in marshy pleistocene sediments in the intermountain valley and in the pampeana prairies. The acid ashed conform rhyoda-cite-rhyolite sediments which form the pampeana loess covers in the prairie.

Jan 1, 1990

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Pina P, Pereira MJ

The increasing exhaustion of raw materials entails the exploitation of poorer orebodies where the target mineral occurs frequently in a very fine dissemination. Consequently it is necessary to grind more and more fine to achieve an adequate mineral liberation. In other words, it is of fundamental importance to know what size one should grind in order to avoid the following detrimental situations: 1. Excessive grinding - giving rise to the generation of ultra-fine slime particles which may be lost in the ulterior concentration process and simultaneously leading to higher energy consumption. 2. Incomplete grinding - giving rise to insufficient liberation and consequently leading to considerable losses of the valuable components in the tailings. Although this issue constitutes one of the most important steps in mineral processing, little research has been done compared to other processes, mainly due to the fastidious experimental work required. This paper describes a complete and integrated system of image analysis, where some algorithms to determine automatically the degree of li beration, for different levels of grinding, are proposed. These algorithms, mainly based on mathematical morphology theory were tested with images obtained from polished sections of different grain size fractions. Cases studies on a complex sulphide ore from an important copper and tin deposit located in the South of Portugal are discussed. Samples of the unbroken ore are also studied by image analysis to predict the degree of liberation obtained according to the fineness of grinding.

Jan 1, 1993

By Yanske TR, Lane WL

The Doc Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 in in height and the use of stinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction hecoming a major portion of the overall production and have added to the mine life of Doe Run's six operating mines.

Jan 1, 1998

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005