Search Documents

By George Rupp

THE Sunrise iron mine of The Colorado Fuel and Iron Corporation is in Platte County, Wyoming, about 110 miles north of Cheyenne. It is served by the company-owned Colorado and Wyoming Railway, which connects with the Chicago, Burlington and Quincy and the Colorado and Southern railways at Guernsey, Wyoming, a distance of 6 miles from the mine. The original Sunrise claims were staked mainly by United States Army officers and soldiers stationed at old Fort Laramie, because of small showings of copper in the Carboniferous limestones that form a horizontal capping overlying the Huronian iron ore. A small copper smelter was operated for about three years at Fairbanks, now an aban-doned town on the North Platte River. As many of the copper shafts and test pits near the present Sunrise mine were deepened, they pene-trated the capping and encountered iron. ore or gray sericitic schist, and were abandoned. Evidence of an early interest in iron ore was found when the Chicago claim was stripped for mining. A narrow, winding crevice was dis-covered, which led downward 20 ft. through the capping to the underlying soft red hematite, in which a room 10 by 14 by 7 ft. had been excavated. Stone hammers and wedges and a few rusted pieces of iron were found on the floor, and the evidence is conclusive that the excavation was used up to rather recent times by Sioux Indian medicine men, to provide war paint.

Jan 1, 1939

By F. W. Robinson

THE temperature coefficient of electrical resistance of pure metals is high and therefore the resistance increases rapidly with rising temperature. In 1871, Siemens suggested the use of this property as an accurate means of temperature determination. Owing to practical difficulties, particularly the contamination of the metal and consequent permanent change in its resistance and its resistance-temperature relation, this method fell into disrepute as a practical standard until revived later by Callendar and Griffiths, and subsequently by Holborn and Wien, all of whom showed that the earlier difficulties were not inherent in the method but incident to the mode of protection of the resistance coils. Following .the work of these investigators, the problem of temperature measurement by this means has been the subject of careful study and has now assumed an importance second only in practical adoption to the thermo-electric method. It is generally recognized, both here and in Europe, that the standard temperature scale should be the thermodynamic as it permits the evaluation of high temperatures on the basis of the radiation laws of Stefan and Bolzmann, of Rayleigh, and of Wien and Planck, on a scale consistent with that obtained by means of the gas thermometer at low temperatures. Lord Kelvin showed that only. a very small correction, amounting to about +0.7° at 1000° C.-almost within the limits of experimental errors-is necessary to adjust the constant-volume nitrogen thermometer to the ideal thermodynamic scale.

Jan 9, 1919

By J. Cervik, P. C. Thakur, S. D. Lauer

Methane drainage by cross-measure boreholes on retreat longwall faces can be a viable alternative to the vertical gob degas boreholes under favorable circumstances. The research was done in a mine working Pittsburgh coal seam in northern West Virginia under USBM Cooperative Agreement No. 14-09-0050-3252. The study was the first application of this technique to Pittsburgh coal seam. A total of 14 small diameter, inclined boreholes were drilled over a retreat longwall panel from gate roads, to intersect the overlying coal seams. All boreholes were manifolded to a pipeline and the gob gas was extracted by a surface exhaust fan. The methane capture ratio was poor at 7% to 18% at various stages of the longwall panel. A vertical gob degas borehole captured an additional 20% gas. Poor results were due to premature failures of the cross-measure boreholes leading to air leakage. For better performance, the boreholes should be drilled from a point 30 to 45 m (98 to 148 ft) from longwall pillar over the largest chain pillar. The standpipe should be grouted for at least 6 m (20 ft), and the entry containing boreholes and the pipeline must be supported to ensure access for maintenance and optimization of methane capture. Coursing the ventilation air around longwall such that it forces methane migration toward cross-measure boreholes can further improve methane capture. The optimum vertical inclination is 45º ± 10º.

Jan 1, 1986

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By L. G. Austin

INTRODUCTION Autogenous (including semi-autogenous) grinding has probably been the most important single innovation in milling practice for the last twenty years. However, the design of these units has been largely a matter of trial-and-error, since the normal empirical laws for the design of ball mill circuits do not apply with exactitude to autogenous grinding circuits. There have been examples of autogenous mills failing to achieve output or product specifications. It is worthwhile, therefore, to attempt to develop a more detailed and precise set of design laws, using the concepts of specific rates of breakages and daughter fragment distributions (1), and performing mill simulations by computer. This type of approach has been applied to ball and rod milling (2, 3,4,5), but even for these mills it is by no means complete as yet (6), because of the amount of experimental work involved. There has not been a strong incentive for industry to develop new design procedures in ball and rod milling because the prior back-log of experience with these mills makes for easy design by empirical comparsion with existing systems. The new approach has been followed mainly by University groups (7,8,9,10), although experience in Australia (9,11) has shown the advantages of the approach. Stanley (12) has applied the approach to results from a large autogenous mill, and we will use many similar concepts to his work, but extend the concepts to a more

Jan 1, 1977

By W. C. Bleimeister

The rock salt deposits of the U. S. occur in five major basins: 1) the Eastern Basin (which includes parts of Michigan, Ohio, Pennsylvania, New York, West Virginia, and Ontario) ; 2) the Gulf Coast Basin (the northern rim of which includes parts of Alabama, Mississippi, Louisiana, Arkansas, and Texas, while its southern rim includes parts of the Isthmus of Tehuampetic and the Yucatan Peninsula of Mexico), 3) the Southwestern Salt Basin (which includes parts of Kansas, Colorado, Oklahoma, Texas, and New Mexico), 4) the Williston Basin (which under- lies parts of North Dakota, South Dakota, Montana, and Saskatchewan), and 5) the Green River Basin (whose periphery underlies parts of Wyoming, Utah, and Colorado). The greatest salt production in the U. S. is obtained from the Eastern Basin,-particularly from the areas of Michigan, Ohio, and Ontario. In 1958 the salt production from these areas amounted to 8.7 million tons or 35.3 pct of the combined total produced in the U. S. and Canada. Of the 24,286,000 tons produced by Canada and the United States, 6,443,000 tons were in the form of rock salt from dry mining, while 17,843,000 tons were produced from wells in the form of artificial brine, the result of dissolving the rock salt formation by fresh water. Three important factors lie behind the location and development of this salt mining area:

Jan 5, 1961

By C. G. Dunn, J. L. Walter

COULOMB' and Coulomb and Lacombe2,3 have recently discussed secondary recrystallization in soft iron (99.5 pct Fe). They found that the appearance of this phenomenon was dependent on both the presence of impurities and the thickness of sheet specimens. They concluded that impurities such as carbon, sulfur, and oxygen in the soft iron stabilized the matrix structure and allowed growth of a few grains of specific orientations. They also found that secondary recrystallization ceased when the final thickness was small and attributed this complete inhibition of growth in thin sheet to the restraining action of thermal grooves. When purer iron (99.99 pct Fe) was used, normal grain growth but not secondary recrystallization was obtained. On the other hand it is known that the necessary stabilization of the matrix structure for secondary recrystallization in high-purity silicon iron probably does not depend on impurities but more likely results from the specimen thickness effect of Beck et al.,4 according to evidence and ideas advanced by Walter and Dunn,5,6 and Detert.7 Furthermore, Mullins8 has indicated that if a gas-metal surface energy difference exists across a grain boundary equal to or greater than about 3 pct of the grain boundary energy, then such a grain boundary should not become stuck. Similarly, Walter and Dunn have estimated that any increase in restraining force due to increased thermal grooving with decrease in

Jan 1, 1962

By F. M. Lewis, Johnson. E. C.

BY now application of the liquid-solid cyclone to various classification problems in the chemical and metallurgical fields is more or less familiar. A less publicized application receiving wider consideration as time goes on is its use as a classifier in closed-circuit grinding operations. This paper presents the costs involved and the experience gained from operating a unit of this kind. In May 1951 the Tennessee Copper Co. installed in its London mill at Copperhill, Tenn., a liquid- solid cyclone in closed circuit with a 6x12-ft ball mill. The circuit in which this cyclone is used is the regrind or secondary grinding circuit of a copper flotation plant. Originally it consisted of a 7x1-ft conical ball mill in closed circuit with a bowl classifier. Changes made in the primary grinding circuit of the mill necessitated a regrind circuit of greater capacity. The bulk concentrate to be ground was raised from 900 or 1000 tpd to 1200 or 1300 tpd, and to accommodate this increase a 6x12-ft ball mill which had been in the primary grinding circuit was moved into the regrind circuit. When this was done it was found that the classifier was too small to give efficient operation. Space in the plant was at a premium, and since use of the cyclone offered considerable economy the installation shown in Figs. 1-3 was made.

Jan 6, 1954

By A. Boltax

The effect of cold work on the electrical and magnetic properties of solution-treated and aged Cu-Fe alloys was studied. The electrical resistivity of solution-treated and of aged Cu-1.7 wt pct Fe samples increased by up to 25 and 140 pct, respectively, follozcing a 55 pct reduction of area. The principle contributions to the increase of resistivity of the solution-treated and aged samfiles are examined. Measurements of the .saturation induction, coercive force, and stacking fault Probability are also reported. 1 HIS paper is the second in a series which examine the behavior of the electrical and magnetic prop- erties of Cu-Fe alloys. The first paper1 was primarily concerned with the effects of thermal treatment whereas the present paper examines the effects of cold work on solution-treated and aged Cu-Fe alloys. The effects of cold work on the transformation of the coherent fcc iron precipitate to the ferromagnetic form2 and the coercive force and remanence3 have already been described, but the unusually large increases in resistivity (up to 220 pct) which occlir with cold work have not been reported previously. EXPERIMENTAL METHOD The methods used for alloy preparation, heat treatment, and electrical and magnetic measurements are described elsewhere.1 The specimens, initially 4-in. lengths of 0.0625-in. diam wire, were cold worked by swaging in hardened steel dies. Following each reduction, the samples were etched lightly in hydrochloric acid to remove surface con-

Jan 1, 1962

Discussion of the paper of THEODORE P. HOLT, presented at the Salt Lake meeting August, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1699 to 1708. F. S. SCHMIDT, Salt Lake City, Utah.-Any furnace that can make a chloridizing roast to yield an extraction of 92 to 93 per cent. and do this at a cost of less than 24c. per ton in a 10-ton unit opens great possibilities for the treatment of certain classes of ores. This cost does not include the salt and will be reduced to about 16 1/2c. per ton in the 35-ton furnace which are now being designed. On a trial run the roaster treated 9.6 ton: of Ontario stope fillings crushed to pass a ¼ -in. opening. The ore is well adapted to chlorination with the exception of insufficient sulphur and occasional days of high lime, but is not adapted to any other process The following is an analysis of the crude ore: Ag, 9.52; Au, 0.029 oz. Pb, 0.71; Cu, 0.11; SiO, 79.4; Zn, 0.57; S, 1.00; Fe, 7.9; Mn, 0.89 CaO, 1.20 per cent. The composition of the mix was: Per Cent. Dry crude ore : 83.4 Moisture 4.4 Salt 8.3 Coal dust 2.3 Pyrite, 70 per cent. pure 1.6

Jan 11, 1914

By W. W. Tyler, A. C. Wilson, L. B. Nesbitt

INVESTIGATIONS of thermal conductivity and impact strength of the titanium alloy RC-130-B and 316 stainless steel were undertaken because of interest in strong, nonmagnetic, commercially available alloys of low thermal conductivity for use in low temperature experiments. Measurements of electrical resistivity and thermoelectric power were also made for some of the samples studied. The titanium alloy designated as RC-130-B is manufactured by Rem Cru Titanium Inc. It contains 0.14 pct C, 3.99 pct Al, and 4.7 pct Mn. A general discussion of properties of the two phase Ti-4Mn- 4A1 alloys is given by Finlay and Vordahl.' The alloy is machinable and has a yield strength greater than 130,000 lb per sq in. at 0.2 pct offset. The 316 stainless steel sample used for both conductivity and impact strength measurements was obtained from the Allegheny-Ludlum Steel Corp. and is designated as Allegheny metal 18-8M, Type 316, Grade 316. The sample had received 25 pct minimum final cold reduction and had a Brine11 hardness rating of 255. Several impact tests were made on a sample of 316 stainless which had not received the 25 pct cold reduction. Also several data points are reported giving thermal conductivity and electrical resistivity for a sample of 304 stainless steel taken from stock. Figs. 1 and 2 give thermal conductivity and electrical resistivity data for the titanium alloy and for

Jan 1, 1954

DESPITE strikes, domestic production of copper and zinc in 1951 rose about 3 pct and 10 pct, respectively. Lead output fell only about 7 pct. Primary refined, including processed scrap and imported concentrates, was somewhat higher for zinc, and slightly lower for copper and lead. Prospects are for moderately larger mine and refined production in 1952 according to Standard & Poor's analysis of nonferrous metals. The survey goes on to report domestic copper prices averaged 14 pct higher in 1951, lead prices 30 pct higher, and zinc prices 32 pct higher. The 2¢ rise in zinc and lead ceilings in October will lift the average price in 1952 over 8 pet, assuming no further price change. Currently, OPS appears opposed to raising the 24 ½ ¢ copper ceiling to the 24 ½ ¢ maximum on imported metal. The steep premiums in world markets are likely to be reduced in 1952. Sales in 1951 were at new peaks. A further moderate rise is indicated for 1952. Earnings of the industry were at a new high in 1951. The increase for companies covered in the survey was perhaps 25 pet, despite a tax rate of about 53 pet, against about 40 pct. in 1950. Relatively maintained to moderately higher earnings are currently indicated for 1952. About two thirds of the companies covered in the survey raised dividends, including extras, in 1951. In general, maintained payments appear probable in 1952.

Jan 1, 1952

By Frank M. Randall

The Buick mill is located at the site of the old Buick general store, approximately 4 miles south of Bixby, Missouri on route KK. It is a part of the operations in the area now called the "New Lead Belt". The ore body lies at an elevation of 270 feet above sea level, and is fairly flat lying, becoming slightly deeper toward the south. The mineralization is due to the secondary deposition of galena, sphalerite, chalcopyrite, pyrite, calcite, dolomite and some localized drusy quartz in a country rock of dolomitic limestone. The galena is fairly coarse grained with some large crystaline structure, and some oxidized surfaces. The sphalerite is fine grained- small crystals containing Cd (about 0.7%) and Ag (about 10 oz per ton) in solid solution. The chalcopyrite is fine grained, fine crystals that are sometimes massive in nature. The mine plan is a modified room and pillar system. Broken ore at the mine face will be transported to several different ore passes by rubber tired load-haul-dump units. Ore passes will drop the ore to a rail haulage level some 90 feet below the mining level where bottom dump cars will deliver it to a 42 in. Nordberg gyratory crusher. Two 12 ton capacity skips in balance carry the ore some 1,200 feet to the surface. The hoist is equipped with automatic controls for loading, hoisting and unloading.

Jan 1, 1970

By Kiyoshi Azuma, Hiroshi Kametani

The variation of the dissolution behavior of a ferric oxide with calcining temperature has been investigated. Samples were prepared by thermal decomposition of ferric hydroxide, nitrate, oxalate, and sulfate at low temperature, followed by the calcination in the temperature range between 600" and 1200°C. The samples of eight series and a fine crystalline sample of hematite were dissolved in 1 N hydrochloric acid at 55.2°C and the results are represented on double-log graphs for convenience. It is confirmed that all dissolution courses follouj either the accelerated process or the parabolic process except in the special case of the crystalline hematite which dissolced in accordance with the uniform dissolution of a particle. Examinations of the physical properties of the oxide powders revealed that the surface area measured by the permeability method is strikingly relevant to the dissolution behavior of the oxide. In the previous paper,' detailed data were presented on the effect of the kind of acid, the solution temperature, and the concentration of acid on the dissolution of two ferric oxides. It was also shown that these sam ples dissolved in strikingly different ways. The present investigation was carried out on the dissolution of various calcined samples prepared from various ferri salts by various methods to ascertain the course of dissolution. Pryor and Evans2 pointed out a change of the dissolution rate at around 700°C for a series of calcined ferric oxides prepared from the hydroxide. Several papers374 reported also the dissolution of ferric oxide samples. It seems, however, that a systematic account of the relationship between the dissolution behavior and physical properties of the oxide has not yet been given. This paper presents the variation of the dissolution of the oxide in relation to the calcining temperature and the change of physical properties of the calcines. EXPERIMENTAL Raw materials were prepared by precalcination of ferric hydroxide, thermal decomposition of ferric nitrate, oxalate, and sulfate, and aerial oxidation of ferric chloride vapor, at as low a temperature as possible. The products were crushed, ground, if necessary, and sieved with a 100-mesh Tylor screen prior to calcination, after which the specimens were dissolved in acid solution. The following is a detailed description of the preparation of the samples. Sample H. About 500 g of ferric chloride (guaranteed reagent) were dissolved in 5 liters of deionized water and filtered. Ferric hydroxide was precipitated by addition of the minimum amount of ammonium hydroxide solution, and the precipitate was washed continuously till chloride ion was not detected by silver nitrate solution, and then filtered. The filter cake was dried at 120°C for a week and ground, and the -100 mesh portion was used. Sample S. Ferric sulfate (guaranteed reagent) was pyrolytically decomposed in a crucible at 700°C for 24 hr and the product was sieved. In this case the following calcination was carried out at temperatures over 700°C. Sample B. Commercial ferric oxide (guaranteed reagent). About 15 kg of ferric nitrate were decomposed in a furnace maintained at 800°C for 2 hr. The actual temperature of the decomposition was not measured. The product was crushed and sieved, and the -100 mesh portion was used. Sample N. About 50 g of ferric nitrate (guaranteed reagent) were decomposed in a beaker in a sand bath until a red-brown dense solid was produced. This product was crushed and sieved, and subjected to complete decomposition at 500°C. The precalcined product was again sieved and used. Sample N2.5. Since the decomposition temperature was not controlled for sample AT, a different sample was prepared in a temperature-controlled furnace. The subscript represents the decomposition at 250°C. The product was treated in the same manner as sample N. Sample Nc. Under atmospheric pressure it is prac-tically inevitable that ferric nitrate hydrate melts to form a brown liquid at about 50°C before pyrolysis. For this reason, the salt was first slowly heated under reduced pressure (about 10-3 mm Hg measured in a trap refrigerated by dry ice-alcohol) to achieve dehydration without melting. About 5 hr were required for the dehydration and the partial decomposition. Then the temperature was elevated to 500° C in air for complete decomposition. The relatively porous product was sieved and used. Sample Ov. About 200 g of ferric oxalate hydrate (extra pure) were dehydrated under reduced pressure (as described above) followed by thermal decomposition at 500°C for 6 hr in air. The decomposition of this salt was accompanied by liberation of carbon monoxide, by which the ferric salt was initially reduced to a black powder. The powder changed in turn into brown ferric oxide as the gas liberation decreased and reoxidation predominated. The product consisted of sparkling fine particles passing through a 100-mesh screen. However it was ground and sieved as for the other samples. Sample D. Commercial fine powder for magnetic tape purposes. The preparation was as follows.5 Ferric chloride vapor and preheated excess air were mixed and passed into a reaction tube where oxidation took place at 450°C. The fine powder formed was collected in a cottrell chamber. The product was vacuum-degassed at 450°C for 1 hr and sieved.

Jan 1, 1969

By A. D. Zunkel, A. H. Larson

Equilibrium arsenic contents of Pb-As alloys in contact with PbO-As2O3 slags containing less than 30 mol pct As2O3, were determined at 650°, 700: and 750 C in an inert at?rzosphere. In this temperature range, the arsenic content of the alloy increased with increasing temperature in the single-phase liquid slag region and decreased with increasing temperature in the two-phase slag region and the single-phase solid-solution slag region. The PbO-As2O3 phase diagram below 22 mol pct As2O3 was determined by thertrzal analysis and by application of a log ?As2O3/?PbO vS log XAs2o3 /x3pbO plot determined from the equilibrium actiuity data. The resulting phase diagram was not well-defined since the eutectic temperature was not detected in the thermal analysis experiments, although a region of terminal solid solubility of As2O3 was found. Results from the phase diagram determination are compared with an existing diagram in the literature. THIS experimental investigation is an extension of a study by the authors1 on the slag-metal equilibria in the systems concerned with commercial lead refining processes such as softening and dross fuming. The first part of this investigation was a study of the slag-metal equilibria in the Pb-PbO-Sb2O3 system. The only experimental work previously done on the Pb-PbO-As2O3 system was by Pelzel2,3 in which the phase diagram for the PbO-As2O3 system was determined below 50 wt pct As2O3 and the equilibrium constant for the reaction 3Pb + As2O3 + 3PbO + 2As was determined as a function of temperature. No slag-metal equilibrium data have been determined. It is due to the scarcity of information regarding the Pb-PbO-As203 system that this work was undertaken. This paper describes the determination of the slag-metal equilibria in the Pb-PbO-As203 system by equilibrating Pb-As alloys with PbO-As2O3 slags in an inert atmosphere, the effect of 1 wt pct additions of bismuth and copper on the slag-metal equilibria, and the PbO-As2O3 phase diagram both by thermal analysis and the use of the slag-metal equilibria data. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade and assayed as follows: 1) 99.8 pct PbO (0.014 pct insoluble in CHJCOOH, 0.02 pct not precipitated by H2S, 0.1 pct CaO, and 0.08 pct SiO2); 2) 99.95 pct As2O3; 3) 99.99 pct Pb; 4) 99.0 pct As; 5) 99.99 pct Cu; and 6) 99.97 pct Bi. Room-temperature X-ray patterns revealed no detectable impurities in any of these materials. Apparatus for Equilibrium and Thermal-Analysis Determinations. The resistance-heated crucible furnace used in this investigation employed nichrome elements and was mounted so that it could be raised to surround the reaction tube during each experiment and, subsequently, lowered. A schematic diagram of the apparatus is shown in Fig. 1. Each charge was heated in a 3+-in.-OD by 31/2-in.-high 416 stainless-steel crucible placed in a 41/4-in.-1D by 18-in.-long fused-silica reaction tube which was closed at one end. On a shoulder around the crucible was placed a 3: -in.-OD by 12-in.-long open-end fused-silica condenser tube. The open end of the reaction tube was covered by a water-cooled brass cap with ports for 1) admitting an inert atmosphere to the system through a stopcock, 2) introducing a stainless-steel, motor-driven, paddle stirrer into the crucible, 3) evacuating the system with a mechanical vacuum pump, and 4) sampling the melt with Vycor sampling tubes. The brass cap was fitted to the open end of the reaction tube with a silicone gasket and collar clamp. The furnace temperature was controlled by a Barber-Coleman Capacitrol controller and a chromel-alumel thermocouple. Due to the corrosiveness of the melt, the controlling thermocouple also served as the measuring thermocouple. The temperature of the melt was calibrated against the controller temperature and was checked periodically during each test with a Vycor-enclosed calibrated chromel-alumel thermocouple. The temperature measurement and control can be considered accurate to ±3°C. Procedure. The charge placed in the crucible for each experiment consisted of 1000 g of Pb-As alloy and 300 g of PbO-As2O3 slag. The crucible was then placed in the reaction tube, the condenser tube was placed on the shoulder of the crucible, the silicone gasket and brass cap were fitted on the open end of the reaction tube, and the entire system was evacuated and filled with argon ten times. After the last flushing, a positive argon pressure of 1 psig was impressed on the system. The furnace was then raised to sur-

Jan 1, 1968

By J. E. Burke

THE origin of recrystallization textures continues to be a matter of controversy. One explanation is that a recrystallization texture occurs because only grains having a limited range of orientations ever appear in the deformed matrix—the oriented nuclea-tion* hypothesis. Another explanation is that grains essentially having all orientations are nucleated but that those having certain orientations grow much more rapidly than any others in the deformation texture, and thus only the rapidly growing grains survive when recrystallization is complete. There has recently appeared a great deal of evidence'- indicate that recrystallized grains of face-centered cubic metals are frequently related to their parent grains by rotations of 20" to 40" about a common [lll] direction. Furthermore, it has been observed that the growth rate of the new grains depends upon their orientations with respect to the matrix, and that the most rapidly growing grains lie within the stated range of orientations. In a recent note, Beck7 has concluded from observations of this type that oriented growth alone is responsible for the appearance of preferred orientations in re-crystallized metals. It should be pointed out. however, that many of the available data indicate that oriented nucleation operates in addition to oriented growth. Thus, while oriented growth may permit a selection to be made among nuclei of several orientations, only a limited number of orientations are available in the first place for such selection.

Jan 1, 1953

By F. F. Craig

Many full-scale waterflooding operations are preceded by pilot floods, one purpose of which is to provide an estimate of recoverable oil. A laboratory model study was made to determine the influence of the producing wells' effective productivity on the oil recovery efficiency of single five-spot pilots, as well as single injection well pilot floods. The effective productivity is indicated by the value of Condition Ratio, defined as the actual well productivity to that of on undamaged and non-stimulated, normal-sized well in the same formation. The effects of initial gas satrcration and mubility ratio on recovery eficiency were also investigated in this model study. Model test results skowed that at favorable mobiliry ratios, a five-spot pilot flood can provide a direct quantitative estimate of the recoverable oil in the pilot area. If the pilot producer's Candition Ratio is 2.2 or more, upwards of 90 per cent of the recoverable oil in the pilot area is recovered from the inside producer, regqrdless of the mobility ratio or initial gas saturation. This Condition Ratio can be achieved with preyent fracturing techniques. Model studies also showed that over the range of imposed injection pressure differences and regional pressure gradients normally encountered in field operations, there was no effect on the recovery efficiency of a five-spot pilot waterflood. Model studies of single injection well pilot waterfloods showed that with no initial gas saturation, the total oil recovery at the offset producing wells can indicate the oil recovery possible by full-scale waterflooding. It is essential that the Condition Ratios of the offset wells be above 1.4. If an initial gas saturation exists prior to water injection, the recoverable oil cannot be directly evaluated by a single injection well pilot flood. However, the production per formance of such a flood can be used to provide information on volumetric sweep efficiency. INTRODUCTION Oil reservoirs are conlplex structures and cannot always be fully studied in the laboratory. Therefore, many operators consider it prudent to evaluate a waterflood prospect by means of a pilot flood. Pilot waterfloods generally involve one of two well arrangements: a single five-spot pilot waterflood, involving four injectors and an internal pilot producing well; and a single injection well pilot flood (sometimes called an inverted five-spot pilot) having one injector and four sur- rounding pilot producers. Some pilot floods are composed of multiple five-spot pilot patterns. To yield information applicable to field-wide performance, the pilot must be located in a representative portion of the reservoir. Pilot floods generally are conducted for one or more of the following reasons: (1) to determine whether water could be injected at desirably high rates, (2) to determine whether an oil bank or zone of increased oil saturation is formed by water injection, and (3) to estimate the oil recovery by waterflooding. Many of the early pilot water-floods were conducted for only the first two reasons. As soon as a buzz in oil production was obtained in the pilot, water injection was initiated throughout the entire lease or field. A number ot laboratory studies have been directed toward determining conditions under which a pilot flood could yield a quantitative estimate of the oil recovery possible by full-scale pattern flooding. One of the early studies of single five-spot pilot flooding' showed that well damage to the inside pilot producer could reduce the total amount of oil recovered. In a study of the single injection well pilot flood pattern,' the results indicated that if the model boundaries were no closer than a half-well spacing beyond the pilot pattern, the pilot performance in the laboratory is unaffected by these boundaries. In another study,? he effect of initial gas saturation and mobility ratio on the ratio of production to injection rate for various groupings of five-spot patterns was defined by mathematical and analog methods. In a study4 involving both potentiometric and flow model experiments at a mobiliry ratio of unity, four different pilot patterns were studied. These included a single five-spot, a single injection well pilot, a cluster of four single injection well pilots and six inverted five-spots. In this study the ratio of well diameter to the distance between injection and producing wells was held constant at 1:1000. The effect of the 7 ratio-—the ratio of the pressure drawdown at the producing wells to the pressure build-up at the injection wells on the pilot performance-was studied. The values of 7 ratio ranged from 0 to 0.34. Results showed that both the total oil recovery and the total fluid production from the pilot relative to the cumulative injection increased with increasing values of the 7 ratio. The effect of both the ratio of injection to producing rates and mobility ratio on the oil recovery performance of a liquid-saturated single five-spot pilot flood was studied in a series of flow model tests.5 Rate ratios ranged from one to four, and mobility rates ranged from 0.1 to 10. Resulls of these tests showed that at low rate ratios, the pilot producers may recover up to four times the recover-

Jan 1, 1966

By J. E. Dutrizac, R. J. C. MacDonald, T. R. lngraham

When sintered disks of synthetic chalcopyrite (CuFeS2) were leached in acidified aqueous solutions of ferric sulfate, the following reaction stoichiometry was obtained: CuFeS2 + 2Fe2(SO4)3 = CuSO4 + 5FeSO4 + 2S Over the temperature range from 50º to 94ºC, the reaction displayed parabolic kinetics. The parabolic rate constant for the dissolution of copper is given by the equation: log.k(mg2/cm4-hr)= 11.850 - 3780/T The activation energy for the dissolution process is 17 ± 3 kcal per mole. The parabolic kinetics have been attributed to the progressive thickening of a sulfur film on the surface of the chalcopyrite. When the leaching solutions contain less than 0.01 molar Fe+3 , the Fe concentration influences the rate of leaching, probably through a mechanism involving the diffusion of ferric sulfate through the sulfur layer. At higher Fe+3 concentrations, the rate control in the leaching. reaction has been attributed to the diffusion of ferrous sulfate through the sulfur. The rate of reaction is insensitive to changes in acid concentration and in disk rotation speed. ThE reaction of acidic ferric sulfate solutions with various sulfide minerals is of practical interest for both bacterial and heap leaching. This leaching medium is generally used with low-grade ores that cannot be treated profitably by conventional means. In both bacterial leaching1-3 and heap leaching, the active agent for sulfide dissolution is ferric sulfate. Although the reactions of ferric sulfate with chalcocite, covellite, and bornite have been investigated,4*7 the kinetics of leaching chalcopyrite with ferric sulfate have not been thoroughly studied. This paper reports a study of that reaction. EXPERIMENTAL Reagent-grade sulfur was purified by the method of Bacon and FanelliB and then it was vacuum-distilled to remove any soluble magnesium salts that had been introduced during the purification procedure.9 From stoichiometric quantities of the purified sulfur and hydrogen-reduced electrolytic copper sheet (99.90 pct Cu), CuS was synthesized at 450°C in a vacuum-sealed, pyrex vessel. About 24 hr was required for the completion of the reaction. A similar procedure involving hydrogen-reduced iron wire (99.90 pct Fe) was used to synthesize FeS1.002. A 2-furnace arrangement was required. The iron was heated to 800°C while the sulfur was maintained at about 400°C. Although the reaction to consume the sulfur was rapid, the material required additional heating (1 week) in a sealed silica ampoule at 800°C before it was homogenized. X-ray powder diffraction analysis confirmed that the copper sulfide was covellite and that the iron sulfide was troilite. The composition of the iron mineral was confirmed by wet chemical analysis. The two sulfides were ground to minus 100 mesh, weighed in equimolar amounts, mixed thoroughly, and pressed into pellets at 80,000 psi. The pellets were vacuum-sealed in pyrex ampoules and then sintered for 3 days at 550°C after an initial heating at 450°C for a few hours. The pellets were then cooled, polished with 3/0 emery paper, rinsed in acetone, and stored. The material had the characteristic brassy color of chalcopyrite and was shown by X-ray diffraction to be CuFeS2. Microscopic examination of the polished surfaces revealed small inclusions of pyrite (approximately 0.5 vol pct) as the only impurity. The presence of small amounts of a second iron compound will not alter the amount of dissolved copper but might increase the amount of ferrous ion slightly. It was calculated that dissolution of all of the pyrite and 100 mg of Cu (a typical value) would change the expected ferrous concentration by only 4 pct. Microscopic examination of a pellet after leaching revealed that the pyrite was not preferentially solubilized; only those pyrite grains at the surface were attacked. Hence, the pyrite is unlikely to alter the rate of copper dissolution. The chalcopyrite disks were about 1.7 mm thick and 27 mm in diam. They were about 80 pct of theoretical density, and for this reason their true reaction area was somewhat larger than the 5.8 sq cm area presented by the polished face. The disks were cemented to lucite cylinders in such a way that only the polished face was exposed. The disks were then leached by methods previously described.6,7 RESULTS AND DISCUSSION Stoichiometry and Kinetics. The initial experiments were directed to the problem of resolving the stoichiometry of the leaching reaction. Disks of CuFeS2 were leached at 80°C for various periods of time in acidified ferric sulfate solutions that were protected from oxidation by a cover of flowing nitrogen. When the disks had been partly leached, they were removed, their soluble salts were washed out, and then they were treated with CS2 in a Soxhlet extraction apparatus. The ratio of elemental sulfur to dissolved copper thus obtained was approximately 2 to 1. After the extraction of elemental sulfur from the pellet, the residue consisted of unreacted chalcopyrite only. For runs in which an appreciable amount of copper was dissolved, the ratio of ferrous ion to cupric ion in the solution was

Jan 1, 1970

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.'j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?' for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4'5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,' is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel's work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969