Search Documents

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By G. Broughton

For the past few years a great amount of work has been done on the viscosity characteristics and gelation of clay suspensions, much of which has been reported in papers published by the Institute.7,12,18,19,24 Impor-tant reviews have been made elsewhere by Evans and Reid,10 Marshall20 and Clews, Macey and Rigby,8 the last two on the general properties of clay. It is unnecessary, therefore, to recapitulate past work beyond recalling that three explanations for the high viscosity and gelation of clay suspensions have been put forward. For lack of more exact nomencla-ture, these may be called the water hull,16 mechanical interference" and attraction-repulsion" theories. The first pictures the clay particles as surrounded by relatively rigid water envelopes, which increase effective volume; the second emphasizes the mechanical interference of platy particles or their agglomerates; while in the third the particles are assumed to be held relatively rigidly at a distance from each other determined by the balance between the attractive (van der Waal's) forces and the elec-trical repulsions of the charges. 13,14 This article presents fresh data on clay suspensions, particularly on the influence of previous flow history of the suspensions, specific contra-ions, temperature, solvation and particle size, in an attempt to contribute to the solution of the problem.

Jan 1, 1938

By Eifu Moriyama

In 1953, Akita Plant, having a capacity of 560 tons per month, was built at Akita city by Mitsubishi Metal Mining Co., Ltd. for the purpose of treatment of the Ikuno and Akenobe Mines's zinc concentrates. Akita city, in whose neighborhood the black ore has been discovered, is located about 500 Km north of Tokyo and faced with the Japan Sea. This plant has been continuously expanded to have the capacity of 7,500 tons per month by the end of 1969. Efforts have been made to mechanize installations and to achieve continuous process. One of the characteristics of Akita Plant is the recent establishment of the residue treatment process. Many processes had been investigated, and finally commercial sulphate roasting of the residue has been carried out since 1965. At Akita Plant, special high grade electrolytic zinc, zinc alloy for die-casting (MAK brand), cadmium, cement copper and sulphur dioxide gas are produced. Sulphur dioxide gas is sent to the next door fertilizer plant to make acid. Table 1 shows production and the average assay of the electrolytic zinc and cadmium in 1969. This plant is divided into four main sections, two subsections, and residue treatment sections: Main sections are: (M-1) roasting section, (M-2) leaching and purification section, (M-3) electrolysis section, (M-4) melting and casting section,

Jan 1, 1970

By T. H. Courtney, G. W. Pearsall, J. Wulff

The mechanism, of the decrease in transition temperature of Nb3Sn was studied. Presintered Nb3Sn powder compacts were heated in a dynamic vacuum at elevated temperatures. Loss of tin resulted from these heat treatments and transition temperature as a function of tin loss was discontinuous at a critical value of tin loss. In general, decreases in transition temperature were correlated with deviations from AS a class, the A15 structure-type (also known as Cr3O or ß W) compounds have the highest superconducting transition temperatures.' In this class are stoichiometry and presence of vacancies in niobium sites. The effect of vacancy distribution on the physical properties of Nh3Sn is considered. It is concluded that the close-packed atomic A chain in the A3B A15 structure must be preserved both in coutinuity and direction if good superconducting properties are to he obtained. tempting to associate these high transition temperatures with the most unique crystallographic feature of the A3B structure: the three close-packed, orthogonal chains of A atoms.'0"' There are at least three principal mechanisms by which the perfection of these "A-atom chains" could be interrupted: changing stoichiometry, inducing disorder, or introducing vacancies. Departures from stoichiometry in either direction in V3Ga lower the transition temperature.7'8 In niobium-

Jan 1, 1965

By R. Sprycha, J. Szczypa, W. Janusz, J. Neczaj-Hruzewicz

INTRODUCTION Because large aqueous suspensions of various fine solids originate during the beneficiation of ores, the Mining Industry constantly requires efficient and feasible dewatering methods. Among the techniques currently in use (1,2), filtration (vacuum, press) and centrifugation are fairly expensive and thus are limited to use with more valuable materials. Furthermore, installations of reasonable size produce only moderate outputs. Therefore, tailings from ore dressing plants are usually treated by sedimentation or settling techniques with a tailings dam as the ultimate sedimentation basin (3). Apart from growing environmental and economic questions, the solid product obtained from the tailings dam basin has in most cases, a rather high moisture content and a persistent semi-fluid consistency. Thus, it is difficult to transport and use further. On the other hand, the solids may be utilized as a filling material, fertilizer, etc. providing they are dry enough and properly granulated. Demands for an improved technique are met to a great extent, by the technique presented in this paper. AGGLOMERATION OF FLOCCIJLATED SLIMES Origin and Qualitative Description of the Process Phenomena of consolidation and pellet formation in flocculated fines were first observed by Yusa and Gaudin (4) while studying rheological properties of flocculated kaolinite. On this basis, methods of separating liquid from solids have been worked out (5-7) and many possibilities for application have been suggested (5,6). Yusa termed the technique "wet pelletization''.

Jan 1, 1980

By Charles A. Kelliher

In November of 1957, the Aliquippa Works started operation of the third basic oxygen furnace shop in North America. This high speed basic steelmaking method provided a very economical increase in capacity at the Works. The success of these two (2) 81-ton furnaces led to the construction of a second B.O.F. shop, producing heats of 230 tons at J&L's Cleveland Works in 1962. The experience gained operating both shops provided the background for the design of the new steelmaking complex at the Aliquippa Works. This new complex consists of a three (3) furnace shop with two (2) furnaces blowing alternately producing heats ranging from 120 to 207 tons. This variation in heat size is predicated on the requirement that approximately 20% of the shop production will be used to supply steel to a six (6) strand casting machine, producing 4' through 7" billets. The new B.O.F. shop has replaced all other steelmaking units including the #1 Shop, where operations were discontinued in September of 1968. With the advent of the strand casting facilities in September of 1969, many of the standard shop practices had to be changed to compensate for higher tap temperatures, longer handling times, and reduced ladle availability. The subsequent changes in these areas led to the evolution of the strand cast ladle practice which is described in this paper.

Jan 1, 1972

By Richard L. Stowe

Four NX-diameter holes were diamond-drilled in competent granite. Samples of the recovered core were used in laboratory tests. A borehole, plate-bearing device known as a Goodman jack was used to perform load deformation tests on the rock in the core hole. The majority of samples used in the laboratory tests were taken from depths in the hole at or within 5 ft of those at which the plate bearing tests were made. Borehole camera records, compressional and shear wave velocities, and densities were measured. Dynamic elastic constants were computed for the in-situ material, while comparative data (except camera records) were obtained in the laboratory. These data were examined to evaluate the significance of the in-situ modulus of deformation (Ed), the value computed from Goodman jack tests. Average test results show an excellent correlation between in-situ and laboratory data. The ratio of laboratory to field deformation modulus ranges from 9.82 to 7.21 for 3,000 and 9,000-psi stress levels, respectively. The dynamic modulus ratio, ED field/Ep lab, is 1.02; the compressional wave velocity ratio, V8 field/V8 lab, is 0.94; the shear wave velocity ratio, V, field/V, lab, is 1.12; and the density ratio, field [y/y] lab, is 0.95.

Jan 1, 1973

By Edgar S. Cook

The Warwick furnace at Pottstown, Pa., constructed for anthracite fuel, is, as may be remembered, 554 feet high, with 15; feet bosh. The actual working height from stock-line to bottom is only 474 feet, the bell-and-hopper taking up 8 feet. During the year 1886 we used mixed fuel, in the proportion of three-fourths anthracite and one-fourth coke. The total product of iron was 30,6299 tons of 2280 lbs., being a weekly average of 589 tons, including all ordinary and extraordinary stoppages. Deducting the latter, the weekly average would be about 600 tons. The fuel-consumption for the year was 1.2 tons per ton of iron, while the ore-mixture yielded 52 per cent. of iron. For about two months during the summer of 1887 we were obliged to run on anthracite exclusively, owing to the Connellsville coke strike. In the fall of 1885, in relining the furnace, the crucible had been built 8 feet 9 inches in diameter, with the view of using regularly one-quarter of coke (the largest previous diameter having been 7 feet 5 inches), and we felt somewhat apprehensive of the results when compelled to use anthracite only. The average of seven weeks' run on coal, as compared with the average of the seven corresponding weeks of 1886 (using one-quarter coke), was as follows:

Jan 1, 1889

By M. P. Tixier, F. Segesman

Explanations bused on theory and laboratory tests tire offered for certain unusual features of SP logs which may befog their interpretation, namely the "sawtooth" SP and the reduction or increase of SP with time. The sawtooth SP is frequently seen in SP recordings of thick, very permeable watcr. sands of the Louisiana Gulf Coast. Using SP data from a resistor network analog, this anomaly is explained on the basis of a thin shale streak within the sand. under which the invading filtrate accumulates by gravity segregcitiorr. The electromotive force then appearing across the shale streak gives rise to the anomalous SP. Reduction of the SP on successive logging runs Ira often been observed in very permeable sands when as indicated by the resistivity curves, the invasion depth has been reduced to practically zero. Laboratory results verify that this phenomenon may be due, to the presence of air electromotive force, across the mod rake when the fluids on either side differ in activity. Also, there is, in some cases; an increase of SP deflection on successive logging runs, because the emf initially present across the mud cake disappears as the somewhat saline water just behind the mud cake is progressively flushed out by the invading filtrate.. Field example and laboratory data are presented. I N T R ODUCT1ON Some unusual features are frequently observed on certain SP logs which make interpretation difficult. The purpose of this paper is to offer explanations of several cases of interest. All of these arc related to the conditions of invasion. The cases to be discussed are as follows. 1. The sawtooth SP anomaly which is frequently seen within the thick, highly permeable saltwater sands of the Louisiuana Gulf Coast 1. Reduction of the SP deflection from the usual sand line in very permeable sections when the depth of invasion is practically nil. As will be explained, such a reduction is attributable to a membrane electromotive force across the mud cake. 3. An increase of the SP with time just after the iormation is drilled as a result of progressive flushing of the invaded zone. FUNDAMENTALS OF SP PHENOMENA An explanation of SP phenomena must begin with the following basic ideas. 1. The SP log derives its character from ohmic potential differences in the hole produced by currents flowing through the mud.' These currents are driven by electromotive forces which are primarily electrochemical in origin. Other possible types of SP-producing electromotive forces may be disregarded for the purposes of this paper. 2. The electrochemical emf's associated with permeable formations are now understood to consist of liquid-junction emf's and membrane emf's.',' As schematically shown by thc battery symbols in Fig. 1, the liquid-junction emf, E,,,, exists at the contact between waters of different chemical activities, a,,,, (mud filtrate) and tr,,. (formation water); the shale membrane emf, lS.sn. exists across the adjacent shales whcn they separate waters of different activities. The emf's just cited are additivc in producing SP currents (arrowed circles of Fig. I). Thus, neglecting for the moment any possible membrane emf across thc mud cake, the total electrochemical emf, E,, will be given by their sum, where K,., -! K,q,, = 12 + 59, or 71 at 75 °F. In the log interpretations the SP of a thick sand (i.e.. the static SP) is generally related to the activities of the filtrate and formation water through Eq. 1. by setting the static SP equal to - E,.

By C. G. Dunn, F. W. Daniels, M. J. Bolton

Recent observations on grain boundary movements in sihcon iron have indicated the possibility of studying grain growth phenomena in two-grain specimens in which several variables affecting growth are readily controlled. These variables are (1) the energy per unit area (?) in the grain boundary, (2) the orientation relationship of the two grains, and (3) the radius of curvature (7) of the moving boundary. Ideally, one grain A should be a narrow rectangular parallelepiped adjacent to a second grain ß as shown two dimensionally in Fig 1. Such a two-grain group becomes unstable when one end of grain A is shaped according to the dotted line. Since the width w of grain A remains constant during growth of grain B, T should also remain constant. The other vari- ables mentioned above can be controlled in the preparation of each two-grain specimen.l,2,3 For a parLicular orientation of each grain, is not necessarily fixed; ? may also depend on the orientation of the grain boundary, but this may be controlled to some degree. The energy relationships for the gowth of grain ß may be derived from the more simple arrangement of two grains A' and B' shown schematically in Fig 2. Here B' largely surrounds A'. Assume these grains are oriented with a common plane parallel with the flat

Jan 1, 1950

By H. A. Schwartz, A. F. Gorton, H. R. Payne

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By H. R. Payne, A. F. Gorton, H. A. Schwartz

In a previous paper1 we published what we believed to be a correct stable equilibrium diagram for an iron-carbon alloy containing + 1.20 per cent. silicon. The purpose of the present paper is to record the results of studies concerning the effect of silicon on the location of the eutectoid points of both systems, including also certain incidental observations of general interest. We prepared white cast irons containing roughly 21/2 per cent. carbon, 0.05 per cent. manganese, and 0.03 per cent. each of phosphorus and sulfur, but of accurately known silicon contents which varied from 0.40 to 3.32 per cent. These were completely graphitized, and both A1 points determined, as in our previous work, the specimens being converted from the stable to the metastable condition and vice versa by appropriate heat treatments. Each stable alloy was heated to a few degrees above Arl for 3 to 7 hr., quenched and analyzed for total and graphitic carbon, the difference being the "combined" or, better, agraphitic2 carbon content of the saturated solid solution just above the eutectoid transformation. One specimen was lost through accident, and the 0.40-per cent. silicon material gave an anomalous result ascribed to difficulty in maintaining the stable system in the presence of but little silicon.

Jan 1, 1923

By C. S. Matthews, G. L. Stegemeier

In one field in South Texas, approximately 72 per cent of the pressure build-up results show a characteris-i.rtic "hump" (i.e., the pressure builds up and then falls off) which makes interpretation by. standard methods impossible Correlation of size and time of hump with formation permeability. well productivitv index, and method of completion led to the tentativc, conclusion that the humps were caused by segregation of gas and oil in the wellbore after closing-in"'. This conclusion was confirmed by performance of simple laboratory bubble-rise experiments, by theoretical bubble-rise time calculations, and by a detailed calculation of PVT behavior in the well of a particular well Oil which accurate Surface and bottom-hole pressure measure-ments were untile. The hump behavior has since been found to occur in many other fields. The cause, however, is not the mine in all cases. In some of these the hump is trace-ahie to leaks in the tnbing which allow influx from the annulus after closing-in. In other cases the hump is traceable to leaks in the device separating pay horizons in dually completed wells. It is concluded that the recording of both surface and bottom-hole pressures is desirable in wells which show an anomalous build-up behavior. A number of field examples is discussed where use of both sets of measurements enables the cause for anomalous behavior to he found, (and a reasonable interpreation of bottom-hole pressure to be made. INTRODUCTION Theoretically the pressure build-up in an infinite reser-voir should be a linear function of In [(t + at)/nere t is the production time and At a the closed-in time. Some of the variations from this behavior arc well known, such as the curved portion immediately after shut-in which results from after-production and skin effect, and the flattened end portion which results from boundary effects in a limited reservoir. The effect of stratified producing zones and irregular geometrical drainage patterns may also contribute unusual characteristics to build-ups. However, the effect of still another phenomenon—that of movement of fluids within the wellbore—has been neglected in most build-up studies to date. Fluid movements within the wellbore after shut-in occur as a result of after-production, packer failures, leaks in the casing or tubing, or buoyancy of the gas phase when both gas and liquid are present in the well. Each of these movements can influence the pressure build-up, sometimes sufficiently to negate use of the data for computing permeability or stabilized build-up pressure. Examples of each of these phenomena are discussed below. FIELD OBSERVATIONS ON HUMP BUILD-UPS In approximately 75 per cent of the wells in a medium-sized field in South Texas the pressure build-up curves rise to 3 maximum and then decline to what appears to be a stabilized reservoir pressure as shown in Fig. I. Similar behavior has also been observed in wells in other fields in Texas and Louisian:,. Because of the possibility of such behavior being a mechanical failure of the pressure bomb. the bombs were run in tanden into one well which had been known to exhibit this behavior. When both bombs recorded identical curves with the characteristic hump, it was inferred that the unusual build-up is a result of well or forma-

By D. A. Flanagan, B. L. Landrum, P. B. Crawford, B. C. Norwood

Herern is described a heat conduction model which has been developed to predict the pressure distribution within a reservoir being subjected to rrnsteady-state depletion. Although potentiometric models have been widely used to study reservoir pressure distribution, their application is limited to the study of steady-state cases. Electrical analyzers may be used to study unsteady-state phenomena, but their application and simulation have certain limitations. Much of the now accepted theory of unsteady-state fluid flow in porous media has evolved from previous heat conduction knowledge. An analogy between the flow of fluid in an unsymmetrical reservoir and con-duct ion of heat in a similarly shaped unsymmetrical metal plate is made to show adaptability of the hear conduction principle to transient reservoir cases. A description of the model and necessary instrumenrarion is included. Data show influence of well location on pressure distribution during unsteady-state deple[ion. Application of results is made to a hypothetical reservoir and to a reservoir located in an irregular aquifer. INTRODUCTION Development of methods for predicting behavior of petroleum reservoirs has resulted partially from adaptation of electrical and thermal flow concepts to the flow of fluids through porous media. Extensive investigation of electrical and thermal flow problems has resulted in mathematical solutions applicable to many reservoir problems. The relative ease of measuring electrical flow has brought wide acceptance of the use of the potentiometric model to study certain field problems. Potentiometric models are restricted to the study of steady-state conditions because of the instantaneous response of electrical flow to changes in the applied potential. The electrical reservoir analyzer has been one of our most useful instruments for studying certain phases of unsteady-state behavior1. Other than approximation techniques, no method exists for determining pressure distribution in an irregular reservoir during primary depletion. Heat flow, like fluid flow, is inherently transient. The model described here was developed to use this transient nature of heat flow, measurable in the laboratory, to simulate transient flow of fluids in the porous medium of the reservoir above the bubble point. A metal plate shaped like the reservoir to be studied was heated by a "well" source. Temperature increase in the plate is analogous to pressure decline in the field if the field is being depleted, or pressure increase if fluid is being injected. This study is intended to determine the feasibility of using the transient nature of the heat flow to study the transient behavior of fluid flow. It is hoped that this new technique will aid in the understanding of one of the more complex phases of reservoir engineering. THE FLUID FLOW-HEAT CONDUCTION ANALOGY The similarity of the equations which describe the flow of fluids through a porous medium and the conduction of heat through a solid is well known2. Rate of flow of fluids is given by Darcy's law3. while the rate of flow of heat is given by Fourier', (I,, - KA 4T........(2) Combining Eq. 1 with the equation of continuity for a compressible liquid", i.e.,results in Expressing y in terms of the compressibility, i.e., pr = peey ,..........(5) and by expanding the exponential and neglecting higher orders of cp one can obtain

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan' obtained kinetic data for the reduction of hematite spheres sintered at 13'70°C (2498'F'). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph' and Edstrom' that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By R. H. Hiltz

Three titanium alloys, known to provide a mechanically unstable p structure after quenching, were selected as material for a study of the Origin and nature of stress-induced transformation. Data from hardness and tensile tests were used to study the initiation of marten site and the effect of the transfornation and transformation products on the mechanical properties of B titanium, particularly the stress-strain relationships. With the exception that the materials investigated showed a natural aging reaction in the P condition, their behavior is analogous to that of' stress-transforming stainless steels. The transformation starts after initial yielding and is essentially complete just prior to .maximum loading. Once initiated, the martensite itself is capable of propagating the transformation. The deforn-ing materials show low strength, high ductility, and a high strain-hardening exponent. In metallic systems which undergo a diffusionless transformation on cooling, it is possible to produce a similar transformatiorl by plastic deformation under special conditions. Dewez' in delineating Ms temperatures for the titanium-rich end of most titanium binary systems:, established the point of intersection of Ms with room temperature for those particular alloys. Alloy compositions which would quench to mechanically unstable p were established from these data. The first investigation into the possibility of stress-induced transformation occurring in titanium met with little success. It was concluded that such a transformation in titanium was possible only under very special conditions. Continued effort in this direction, however, showed certain Ti-Mo binaries to be highly susceptible to this phenomenon. This fact was utilized by Liu to study the habit planes of martensite and by Machlin and wenig5 to study the effects of stress and plastic deformation on the P to a prime transformation in titanium alloys. The first investigation of the mechanical properties of these alloys was conducted by Holden and his coworkers at Battelle Memorial Institute.' The potentiality of the alloys i3s sheet-forming material was recognized, and the data reappeared in a survey of this type of titanium material.? The initial optimism was tempered by the difficulties in obtaining homogeneous 2i-Mo alloys in commercial-size ingots. The increasing need for good sheet-forming material kept investigation in this direction active, resulting in the development of a commercial alloy of this type.' This study was undertaken to obtain a clearer picture of the mechanism of stress-induced transformation in titanium. MATERIALS AND TEST PROCEDURE Three alloys were selected for this investigation: one a Ti-Mo alloy; another a Ti-Cr-Mo alloy, known to deform martensitically; and the third, a Ti-V alloy with an Ms below room temperature and an Md above room temperature, but known to contain w phase in the quenched condition. The compositions of these alloys are given in Table I. These alloys were cast as 5-lb experimental ingots, employing skull melting. The ingots were hot-forged into 1-in.-round bars. Two 72-in.-thick slices were cut from each bar for hardness testing; the remainder was cut into 0.252-in. tensile blanks. The tensile blanks and one hardness disc from each bar were heated in salt to a temperature 100°F above the 0 transus, held 2/2 hr, and brine quenched. X-ray analysis showed the pieces to be 100 pct 8.* *Omega cannot be distinguished from p by the technique employed. Tensile blanks were machined to size after this treatment. TO prevent transformation due to machining stresses, the shoulders and gage length were ground. True stress-true strain curves were

Jan 1, 1960

By R. M. Waterstrat, B. N. Das, Paul A. Beck

The central region of the Ti-Mn system was studied by means of x-ray diffraction and metallography. The following intermediate phases were found: an MgZn2-type Laves phase having a wide range of homogeneity, the p-phase of unknozvn structure, and the + -phase with a large tetragonal unit cell, stable at 930°C and lower temperatuves. MaYKUTH, Ogden, and jaffee1 determined the soh-inh bility limits of manganese in and titanium. They also confirmed the structure of the intermediate phase TiMn2 which was previously identified as a Laves phase of the MgZn2 type.2 In the equiatomic region they found an additional intermediate phase, y, which presumably formed by a peritectic reaction at approximately 1200°C. This last observation was disputed by Rostoker, Elliott, and McPhers0n,3 who reported the formation of TiMn by a peritectoid reaction between 900" and 1000° C, but found no evidence of any intermediate phase other than the Laves phase at higher temperatures. Elliott and Rostoker4 reported furthermore that the X-ray diffraction pattern of TiMn could be identified as that of a o phase, although their data were not consistent with this inter~retation. Margolin and Ence6 presented X-ray diffraction data for the and TiMn, phases, and obtained metallographic indications for the existence of additional intermediate phases. They concluded from metallographic observations that two Laves phases are formed, separated by another phase, designated as &. A phase diagram for the Mn-Ti system has recently been published by Savitskii and Kopetskii,' which shows considerable disagreement with the work of Hellawell and Hume-Rothery,' in particular with regard to the terminal solid solutions based on the allotropes of manganese. The present investigation was undertaken primarily to clarify the phase relationships in the equiatomic region of the Ti-Mn system. The metals used in preparing the alloy specimens Were iodide titanium and electrolytic manganese, the latter having a nominal purity of approximately 99.9 pet. The electrolytic manganese was covered with a thick coating of a brown manganese oxide which was reduced by heating the manganese flakes for several hours at a temperature of 1100°C in an atmosphere of dry hydrogen. Three alloys, see Table I, were made using sponge titanium and manganese not treated in hydrogen. The alloys were prepared by arc-melting in an atmosphere of helium or argon. The composition of each alloy was calculated by assuming that the entire weight loss during melting was due to evaporation of manganese. Subsequent chemical analysis of certain alloys indicated that the compositions calculated in this manner were usually correct within 1.4 pct, as shown in Table I. All alloy specimens were wrapped in molybdenum foil before sealing them in silica tubes containing argon at a pressure of 1 atm at the annealing temperature. After quenching in cold water, the alloy specimens were bright and clean, with no evidence of any surface reaction. The alloys listed in Table I were examined metallographically, using an etchant consisting of 20 pet HNO3, 20 pet HF, and 60 pet Glycerine. powder for X-ray diffraction examination was prepared by crushing a portion of each annealed alloy

Jan 1, 1962

By B. Ehgartner, M. Karmis, C. Haycocks

INTRODUCTION Interaction effects between mining operations developed on different levels of contiguously placed bedded deposits are a major problem in many parts of the United States. Efficient design criteria, derived from careful analysis of field studies as well as theoretical and model analysis, have shown that many problems that may result from seam interaction can be avoided, minimized, or on occasion used with beneficial results. Selection of seam mining sequence is rarely based only on ground control considerations, but rather on factors such as seam ownership, characteristics and accessibility. Therefore all possible mining sequences and methods must be considered in the development of multi-seam design criteria. Increased utilization of the longwall method of mining creates special problems in multi-seam mining due to the inevitability of caving and, therefore, subsidence. Considerable valuable experience has been gained in this direction from British mining operations where interaction problems are extremely common and the longwall method is the primary method used. However, limitations persist in the application of much of this information to U.S. conditions due to variation in layouts between advancing and retreating longwall systems and the inherent difference in the geologic environment. Considerable field data is available for U.S. room and pillar operations, and where successful pillaring operations have been carried out close parallels may be drawn with ground control mechanisms in longwall operations. VARIABLES AFFECTING INTERACTION Analysis of ground control multi-seam problems shows that factors contributing to interaction may be classified into variables that are fixed by the geo- logic environment and those that depend on engineering design. These may be described as follows (Haycocks et al, 1982): Fixed: (i) Depth*, (ii) Innerburden thickness*, (iii) Innerburden physical characteristics*, (iv) Stress field, (v) Seam thickness, (vi) Coal characteristics, (vii) Completed mining operations either above or below the seam to ve mined, and (viii) Age of workings. Mining: (i) Height, (ii) Dimensions and geometry*, (iii) Method*, and (iv) Spatial location of entries* *These variables are regarded as being critical effects. Few attempts have been made to quantify the variables controlling interaction. Dunham's (1978) linear regression analysis, combined with the National Coal Board's MRDE Roadway Monogram, is probably the most noteworthy. This study involved eighteen multi- seam longwall mines in the United Kingdom. The following variables were taken into account: seam depth, pillar width, opening shape, floor and roof conditions, rate of face advance, vertical seam interval, and age and geometry of overlying workings. A multi-linear regression analysis of these variables fitted by appropriate field values developed a prediction equation for lower seam stability. Although the study included many variables, it neglected the nature or geology of the innerburden. The prediction equation was found unreliable, but it did show the significance of geometry as a factor controlling lower seam stability. MINING SEQUENCES Irrespective of the type of mining method selected only four possible mining sequences are possible for two seams. Finlay and Winstanley wrote in 1934. .. "Experience has shown that whether the upper or lower seam was worked first, the subsequent working of the other seam in the same area seriously affected the roads in the seam first worked." Those effects depended upon the four basic mining sequences: 1) The upper seam is mined out prior to mining the underlying seam; i.e., the seams are mined sequentially downward and mining of the underlying seam is not commenced until operations above are completed and have ceased.

Jan 1, 1982

MEMBERS-QUALIFICATIONS AND ELECTION SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall he entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which be must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, however, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which be may belong.

Jan 1, 1938

By Frank Firmstone, Kenneth Robertson

Peculiar crusts having appeared on certain irons made at Glendon and Pequest, which, in our experience, were entirely new, some analyses of them were made; and these analyses, together with an account of the manner of appearance of the crusts, are herewith submitted to the Institute. At Pequest the ores mere: & Peters, from Ringwood, N. J.; + roasted sulphurous ore, from Charlotteburgh, N. J.; and + red ore (decomposed magnetite), from Chester, N. J. The fuel was 7/8 Lehigh anthracite and + Connellsville coke, and the limestone a dolomite from Andover, N. J. The resulting iron varied in silicon from 0 84 per cent. in No. 1 foundry to 0.51 per cent. in gray forge; in phosphorus, from 0.81 per cent. to 0.55 per cent.; sulphur, 0.035 per cent.; manganese, 0.375 per cent. It was highly "chilling" in its properties, and very strong. In running, it invariably appeared to be of a lower grade than it really was; the higher grades scintillating as much as hard iron usually does. After getting into the moulds, and beginning to cool, a black crust began to show itself, seeming to exude from the pigs, till finally, when the iron was cold enough to break, it completely covered the face of the pigs. At this time it was dense black, but after some exposure to the air it ac .

Jan 1, 1884