Search Documents

By R. H. Richman, II Conard G. P.

AS part of a study of deformation twinning in bcc crystals, solid solutions of beryllium in iron have been found to twin profusely when strained slowly at room temperature. This note reports some crystal-lographic aspects of the operative mechanical twin modes in a quenched Fe-5 wt pct Be alloy. After melting twice under a partial pressure of helium, the alloy was homogenized, cut into pieces 7 to 10 mm on an edge, solution treated at 1130°C,1 and quenched. Debye-Scherrer patterns confirmed

Jan 1, 1963

By S. R. Gilbert, B. W. Burdett, L. B. Hales

INTRODUCTION Grinding control is currently the most publicized control subject in the minerals industry. Flotation control and crushing control have not as yet received the widespread attention that grinding control has. The primary reasons for this center around the high capital costs of grinding equipment and the fact that grinding mills are extremely energy inefficient. In a typical copper concentrator the energy requirements to produce refined copper are: (1) [Total Energy Distribution (Kw-hr/yr)% Mining4.93 x 10817.3 Mineral Processing9.63 x 10833.8 Smelting and Refining13.9 x 10848.9] One-third of the total energy used for copper production is for mineral processing. A breakdown of this energy into process steps yields the following: [Total Energy Distribution (Kw-hr/yr)% Crushing and Grinding 7.16 x 108 73.8 Flotation 0.76 x 108 7.8 Materials Handling1.78 x 10818.4] It is apparent that comminution operations consume the largest proportion of the energy for processing and as such become major targets for improvements in efficiency. Unfortunately, size reduction operations are extremely inefficient. Efficiency calculations for grinding range from less than 0.1% to about 5% depending on the evaluation criteria. Because of these facts, grinding control has been and will continue to be the focus of major process control efforts. OBJECTIVES AND BENEFITS All benefits achieved as the result of grinding control are derived from modifying physical parameters which improve the efficiency of the grinding mill. These parameters include:

Jan 1, 1982

By Mara Kosovac, Sujan K. Kundu

The Iron Ore Co. of Canada (IOC) has developed a computerized plan analysis method for its open-pit iron mining operations which will eliminate much of the tedious manual drafting of pit design plans performed by engineers and geologists at its two major operational areas near Schefferville, Que., and Labrador City, Nfld. The new technique permits analysis of section or bench plans for a specific ore body, based on drillhole information; preparation of a three-dimensional unit profit matrix for pit design purposes, and storage of extensive ore-block information for other applications. Other advantages include enhanced design accuracy through reduction of human errors normally associated with preparation of large data masses, and by elimination of errors inherent in planimeter-prepared ore block diagrams.

Jan 7, 1978

By O. E. Kiessling

Viewed from the standpoint of an economist, the task which faces the petroleum producing industry is one of intelligent adjustment so that technology can perform the job of efficient exploitation, while at the same time the interests of producers and consumers remain adequately protected. The crux in the task of making this adjustment lies in the difficulty of arranging the instrumentalities of production to accord with the physical characteristics of oil. For example, oil is exploited under a competitive economic system based on private ownership and contract, with the hope that profits will attract capital and enterprise, and with competition supposedly acting as the regulative factor. Whether such a scheme of industrial organization works is partially dependent upon the ability of the producer to withold or produce his commodity as he sees fit, in accordance with market demand. But in the oil industry, the enterpriser does not have complete control over the expansion and contraction of production, for, because of the decisions of the courts that ownership in oil depends upon its possession, desire for immediate output becomes the controlling force in production. Consequently, the theoretical commands and restraints of free enterprise are not operative because there is no security of property, and the result is loss due to the following economic maladjustments: (1) Production not completely responsive to price control. (2) Production at excessive cost. (3) Loss of oil, a highly exhaustible natural resource. If economic maladjustments are to be eliminated, there should be a change in the organization of production so as to provide efficient exploitation of the oil and at the same time to insure individual property interests. The latter is necessary if economic considerations are to become primary factors in regulating production. To attain these ends, the entire pool should be developed as one big engineering project and some scheme

Jan 1, 1928

By R. S. Sandhu, L. E. Baker, W. Y. Shieh

The finite element method of analysis was introduced by Clough.1 Within a short period, it has developed into a powerful solution technique in structural and continuum mechanics. It has been used to solve boundary value problems in two and three-dimensional elasticity.2-5 Anisotropy and heterogeneity of materials were allowed for at the earliest stages. 1,4 Its application has been extended to allow for cracks,5 creep and viscoelasticity, 6,7 incremental construction,6-8 nonlinear elasticity3,9 effect of joints in rock,10 and to materials with different behavior in tension and compression.7 Because of its versatility, the finite element method has found increasing application in the field of rock mechanics. In fact, several of the more significant developments have been motivated by problems in this field. Elasto-plastic material behavior based on the incremental or rate-type theory of plasticity rather than the deformation theory was considered by Reyes and Deere11 A material law based on a generalization 12 of the Mohr-Coulomb criterion was used. In this chapter, the formulation of material laws developed by Reyes and Deere 11 is used. An efficient analysis procedure, incorporating recent developments in finite element analysis, is developed for plane-strain conditions. To demonstrate its effectiveness, the procedure is applied to three cases, one for which an exact solution is available, another for which field observations had been made, and a third one for which a parallel study was made, using an accepted limit-equilibrium method.

Jan 1, 1970

By Edward Steidle

THAT veterans are crowding the colleges is no longer news; 78 per cent of the 1916-47 enrollment in mineral industries curricula in the United States were veterans, but the rapid comeback from an estimated 1262 total mineral industries students in 1944-45 to 11,422 in 1946-47 is almost astonishing. The figure, which includes 1008 graduate students, is a substantial increase over the previous top record of 9619 in 1938-39. A small part of the increase is caused by the larger number of women entering the field, of whom there were c 9 in 1916-47. Petroleum leads the curricula with 34.5 % of the enrollment, metallurgy is second with 28%, and mining is third with 18%. Table 1. shows all curricula offered and those accredited by ECPD. Using the Mississippi River as a dividing line, 31 colleges in the East and 27 in the West offer curricula in the mineral industries.

Jan 1, 1948

By Tong Guangxu

INTRODUCTION Throughout the world, the caving mining methods of ore-draw under the overlying waste rock are sublevel caving in Sweden, block caving in U.S.A. and forced block caving and sublevel caving with sill-pillar in U.S.S.R. These caving methods are of high efficiency, low cost and large production (especially the block caving method) when compared to opencast mining. From the ore production of all under- ground mines, the largest annual production of underground metalliferous mines in the world is caving methods. The sublevel caving in Kiruna Iron Mine of Sweden has reached annual ore production over 20 million tons in 1974. The block caving in Climax Molybdenum Mine and San Manuel Copper Mine of U.S.A. both have produced about 40 thou- sand tons of ore per day in 1971. At the same time, the productivity of Kiruna was 12 thousand tons of ore per man-year, Climax 42.8 tons (48.3 short tons) per man-shift and San Manuel 29.01 tons (32.1 short tons) per man-shift. The main feature of this group of mining methods is the underground extraction of ore from beneath overlying caveable waste rock. Since the loss and dilution of ore are inherent (sometimes to a great extent), the control of ore-draw in these methods as com- pared with other methods is very important. Consequently, concerned Universities and Research Institutes have devoted great amounts of research on ore-draw theory and control management which has provided positive results to mine production, and has apparently promoted the development of the caving methods. During 1979 in China, metalliferous underground mines accounted for 15.22% of the total iron ore produced, while also accounting for 56% of total non-ferrous production. According to the mining methods, sub level caving in the principal underground iron mines counted for about 56.74% of total principal underground iron mine production, but only about 1% of total non-ferrous underground mine production. Relative to forced block caving and sublevel caving with sill pillar, the Chinese non-ferrous under- ground mines estimated about 35% of total non-ferrous underground mine production from these two methods, mainly from the latter. From the trend of development of underground metalliferous mines in China, the percentage of production in caving will be increased in the future, especially in block caving and forced block caving which have already been given great attention in the mining circle. In these types of mining methods the ore is drawn from the stope under a large area of overlying waste rock, which complicates the basic regulation and control of ore-draw, but provides lower loss and dilution than sublevel caving. Because of these reasons, the Kiruna Iron Mine in Sweden is intending to change its sublevel caving by testing a sublevel shrinkage caving method and considering a large area of ore-draw beneath the stope as an advantage. Therefore, the basic regulation and control management of ore-draw under a large area, as practiced in China, will be discussed in this paper. BASIC REGULATION OF ORE- DRAW FROM CAVING STOPE The aim of studying ore-draw under a large area of overlying waste rock is to se- cure a planned draw schedule that guarantees a certain plane of interface between ore and waste rock, and controls the change of its shape in spatial position for reducing ore loss and dilution during the draw process. Presently, the ellipsoid theory is comparatively near the actual attitude of ore-draw from the cave. 1. Ore Drawn Out from Single Drawpoint Laboratory testing and practical experience all show that after a certain amount of ore has been drawn out from a drawpoint, its original shape in the stope before drawing is more or less similar to an ellipsoid, hence the name "draw ellipsoid." This draw ellipsoid is cut at the bottom by a horizontal plane corresponding to the raise of the drawpoint, and its volume can be calculated by the following formula:

Jan 1, 1981

By E. G. Banks

THIS paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine-more especially that produced in the upper levels-contains a large proportion of hard, chalcedonic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to ob¬tain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded

Jan 1, 1907

By John Mathews

CERTAIN physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from ;shrink holes, cold sets, .pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to, consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.-The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the "set," or the detail appearance of the surface of the shape (the wave-like struc-

Jan 2, 1920

By Zay Jeffries

OF the new production of non-ferrous metals in 1930 gold will rank first in value. We usually think of copper as the most important non-ferrous metal. The copper industry as a whole, that is, adding copper production to copper fabrication, is the largest non-ferrous metal industry. Prior to the world war; however, gold led in value of new metal produced. During the war copper passed gold in value, but gold regained its position during the 1921 depression. For the past several years copper has again passed gold, but in 1930 gold promises again to regain the lead. The gold producer has at times been called a social parasite, largely because we ' cannot eat or drink gold, or because we cannot use it for clothes or for the construction of buildings. Let us briefly examine this accusation.

Jan 1, 1930

By R. M. Brick, F. L. Vogel

THE elementary mechanism of deformation in the body-centered cubic metals has been a subject of dispute for many years. If the problem were merely that of designating the crystallographic plane or planes of slip, the solution would have appeared long ago. However, there must be greater differences in the deformation behaviors of the body-centered and face-centered types than the differences in their lattices would suggest. The lines of slip formed on the polished surface of a strained face-centered cubic metal conform to glide over a single plane of the crystal. Slip in body-centered cubic iron, however, is frequently observed as curved and forked lines which could not possibly define a single plane of atoms. This alone is sufficient reason to expect different modes of deformation to operate in the two lattice types. The literature in this field now has generally accepted the proposition that {110), {112), or (1231 planes will act as slip planes in iron. It is essential that the experimental evidence supposedly supporting this proposition be critically examined. Taylor and Elam1 in 1926, using relatively small single crystals, determined the operative slip systems by measurements of the distortion of a grid engraved on the specimens prior to deformation. Their results indicated that shearing had taken place in the close-packed direction on a plane adjacent to or coinciding with the plane of maximum shear which contained the slip direction. This led the authors to propose a theory of noncrystallographic or banal slip. The authors considered an alternate rationalization of banal glide. Slip on two (1101 planes or possibly two {112} planes containing the same <1ll> direction could produce the wavy slip lines. By employing plane segments of varying widths, the integrated plane could take any position in the <111> zone. They rejected this explanation, however, feeling that the preponderance of evidence was against it. Taylor&apos; continued the investigation of the plasticity of the body-centered cubic lattice on ß brass. He reasoned that the resistance to shearing of a given plane in the zone of the slip direction was a function of the angle between the glide plane and the closest (110),: P F=—cose sine cos(X —?) [1] where F is the resistance to shear; P, the axial load at yielding; A, the cross sectional area; e, the angle between slip direction and load axis; x, the angle between plane of maximum shear containing the slip direction and the (101) pole; and ?, the angle between observed glide plane and the (101) pole. Differentiating Eq. 1 and rearranging, dF — = tan(x-?) d? [2] F which expresses the variation of the shear resistance with the angle $. Integrating this equation between the limits 0 and ? yields In F/F0 = ?0?tan(x— ?) d? [3] Here, F, is the resistance to shear of the (110) plane and F is the resistance to shear of a plane $ degrees from the (110). Thus, the variation of shear resistance with $ can be calculated from an experimentally measured x vs $ relationship. Fahrenhorst and Schmid8 sed several methods, none of them involving direct observation, to determine the glide system in ferrite. They determined the variation of critical resolved shear stress with

Jan 1, 1954

By Bernard York, John J. Reed

J. P. Zannaras (U.S. Tungsten Corp., Congress, Ariz.) —In the investigation described in the paper by Bernard York and John J. Reed, the 8x8x8-in. square block was subjected to compressive forces from three sides, top, side, and rear. Let us refer to the stresses set up by these forces as Sz due to top pressure, Sy due to side pressure, and Sx due to rear pressure. At the section across the 2-in. hole (when failure occurred at 317 psi) the compressive stress Sy was equal to 317 x 8/6 = —422 psi, the top compressive stress S; is of the same intensity, —422 psi, and the rear compressive stress S, equals —317 psi. The true stress is T = Sy — S — S Taking as 0.2,* Taking the case when the opening was ½ in. and failure occurred at 517 psi, 8 Sy - 517 x -----= —537 psi 7.5 8 Sz = 517 x-----= —537 psi 7.5 Sx = —517 psi The true stress T = Sy — Sz — S, T - —537 + 0.2 x 537 + 0.2 x 517 = —327 psi. It can be shown that the above fundamental formula holds good not only for the above two examples but for all sizes of openings used, because when this formula is expressed in terms of the external pressure and size of the opening it agrees perfectly with the experimental results obtained by the authors and given in Fig. 12 of their paper. General formula: T = Sy — s: — S....

Jan 1, 1955

By A. E. Perkins

fractured ingot will show a complete diagonal structure. If the temperature is lowered, the equi-axed zone is larger and the pine tree growth is less. A small ingot, though, is prone to this columnar structure, even though the casting temperature is kept down. The speed of cooling after solidification is slower in the hollow ingot than in the solid, therefore the granulation, which takes place after the crystals have formed from the liquid metal, is apt to produce larger grains than in the solid ingot. This is not a detriment. The original crystal size is of much more importance. The size of the grains due to this granulation constantly varies in response to mechanical work and subsequent heat treatment. Surface weakness, as shown by seaming and checking on the exterior when working or by cracking in hardening, is in some measure the result of the surface stresses of the ingot when cast. The temperature of the ingot mold or speed of freezing of the exterior of the ingot is of great importance and much seamy and cracked steel is caused by a too quickly cooled skin. Ingots that are turned or milled all over will not seam very much in working, in fact they are practically free from seams, whereas an ingot rolled without a preliminary machining operation is full of seams and cracks, some long and some short. It has been said that these short seams and cracks in the surface of the bar are the result of elongated depressions in the surface of the ingot and that if an ingot is cast very smooth it should give fewer surface defects. This is partly true, but an ingot cast very hot and having a very smooth skin will crack and seam very badly in the mill, as will the surface of an ingot poured very cold, which is very crinkly, because of the low temperature of the metal. The cause of the cracks and seams in one is not the cause of the cracks and seams in the other. The tube method of hollow drill steel manufacture is superior to the older method because of: (1) Greater freedom from external and internal straining; (2) the inherent small crystal size; (3) absence of harmful segregation, resulting in weakness of wall of hole. (4) less liability for steel to crack in inside of hole during forging or hardening; (5) toughening effect, arising from mild steel wall of hole limiting the intense hardening on quenching. Breakage and Heat Treatment or Rock-drill Steel By A. E. Perkins, Pittsburgh, Pa. Actual figures showing the superiority of one section or another are difficult to obtain. In a given size of steel, however, the cruciform sec -tion shows the most breakage; it is inherently a weak section. It contains less steel per foot than any other standard section of the same size and when rolled the wings tend to cool off setting up cooling stresses.

Jan 1, 1922

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By Richard P. E. Hermsdorf

IN the nonferrous sessions this year, magnesium wiggled its way into a dace of prominence such as it has never before enjoyed. This was evidenced not only by the number of papers presented on that metal but by the attendance at the meetings. The atmosphere permeating these magnesium meetings was similar to that which exists in a family with a new baby. Everybody crowded around to see what it looked like and then wondered whether it would be a success and credit to the family. Well. magnesium appeared to be a vigorous youngster, full of life, and raring to go. A close relative of maenesium named " aluminum, although much more grown up, also attracted much attention. From the activity and spirit in these sessions

Jan 1, 1944

By Walter G. Perkins

T SEEMS almost sheer presumption to attempt&apos; to discuss Russia in its present chaotic political and economic condition, and were it not that at least two certain absolute factors are continuously at work, it would be impossible to&apos; even approach the subject with any degree of intelligence. These are the inborn love of peace of the people and the national character of the cooperative movement. The love of peace inborn in the soul of every Russian, the desire to be left alone and to- live his life among his home village surroundings, is probably one of the two greatest factors that will make the continuance of the present conditions of civil war impossible. One army or the other may sweep up and down the country. but the Russian peasant will: remain in his own village if not literally darken out. This love of peace is evidenced by the fact that there is no country where personal safety is greater than in Russia in normal times. I have traveled in many isolated parts, carrying considerable sums of money and persolial equipment that; in itself, would be a fortune to any peasant, and have never even encountered a condition in which the most wildly imaginative person looking for adventure, 01: trouble, could muster up even a suspicion of fear. This statement applies also to Southern Siberia and Northern Turkestan, which are inhabitated by the nomadic tribes of Khirghese origin.

Jan 1, 1920

By Willis Burns

I. INTRODUCTION. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character.

Jan 8, 1913

By S. F. Emmons

In a report upon the geology of Ledville and vicinity, which is till in the hands of the Public Printer, I hare given, at some length, my conclusions as to the genesis of the remarkable silver-lead deposits of that region, and the data, gathered during a long and careful consideration, upon which my views were founded. In the brief abstract of this report, published in 1881, the bare conclusions are given, with but few of the facts upon which they were founded. Since that time, these conclusions have been variously criticized, and it has even beer] assumed that the views I expressed with regard to these deposits were intended as a theory of ore-deposits in general.

Jan 1, 1887

By Alfred H. Bell, George V. Cohee

In 1939 Illinois produced 94,302,000 bbl. of oil—almost three times the amount of oil produced at the peak in 1908, when development in the southeastern Illinois field was at its height (Fig. I). It represents nearly a fourfold increase over the 24,075,000 bbl. produced in 1938 (Table 6). This rapid increase in oil production in Illinois is largely due to development in the Salem and Louden fields (Table I). During 1939 daily production for the state increased from 135,000 to 332,572 bbl. A notable increase in production for 1940 is expected as a result of the drilling of the Devonian limestone in the Salem and Centralia fields,

Jan 1, 1940