Search Documents

By Robert W. Hunt

In 1888 the writer had the honor of submitting to the Institute a paper on " Steel Rails and Specifications for their Manufacture."* In his judgment the specifications were sufficient for "that day and generation." In that paper I said: '' The first duty falls upon the railroad engineer in designing his section. If that is bad, the steel-maker will be heavily handicapped in trying to furnish a satisfactory rail. I suppose it is hopeless to expect the adoption of standard sections."

Jan 1, 1896

By R. E. Hucko

Introduction The principal thrust of the US Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce ash and sulfur content of US coals to levels where the resultant product can be formulated into a high quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The coal preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in house and by a cross section of industrial organizations, universities, and national laboratories. Research is subdivided into three areas - coal characterization, beneficiation, and ancillary unit operations.

Jan 1, 1985

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 12, 1979

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1980

By Paul R. Bluekamp

The Mather Mine property is composed of a 5.2 sq km (2 sq mile) area within the Cities of Ishpeming and Negaunee which are located in the Upper Peninsula of Michigan. Production in this mine started in 1943; it ran continuously until its closing in 1979, having produced slightly over 55 million tons of iron ore. This mine was a joint venture between several steel companies and The Cleveland- Cliffs Iron Company (CCI), with CCI being the fee holder and operator. For the first 17 years of operation, the ore was shipped in its natural state directly from the mine to the steel mill. By 1960, iron ore pellets were on the market and they proved so superior to the natural soft Mather ore that the latter became difficult to sell except for the coarser portions. It was decided to develop a pelletizing process for the Mather ore, and this was accomplished by 1965 when the first Mather pellets were produced. From this date, all but the coarse fraction of the Mather ore was shipped as pellets. The geological setting is that of a large east-west trending synclinorium which plunges to the west. The lowest member of this trough-like structure is, for the most part, a quartzite-like graywacke, the upper 20 m of which grades into a softer, fine grained slate. Lying conformably on this graywacke footwall member is an iron- formation member which is over 1,300 m in thickness. This iron-formation is cow posed of thin alternate bands of iron oxides and chert and is intruded by a number of diorite sills - some up to 122 rn (400 ft) in thickness. The north limb of this synclinorium dips at approximately 45' and bottoms out at about 1,000 m from surface in the central part of the mine. There are two sets of faults, many of which are intruded by diorite dikes, which trend east-west and southeast-northwest. Displacements are varied, reaching a maximum displacement of 243 m (800 ft). The ore is found lying directly on the slatey footwall and its position is largely controlled by the faults and dikes, with the bulk of the ore being on the upper side of these structures. The ore is composed of soft earthy hematite and martite with vertical thicknesses up to 122 m (400 ft) although the average thickness would be closer to 46 m (150 ft). The ore averaged 60% iron and 7% silica on a dried analysis. The Mather Mine is located on the north limb of the syncline and was worked from two shafts, the deepest of which. was 1,09 7 m. These two shafts are about 2 km apart and serviced a total of 8 working levels between them during the life of the mine. The level spacing was about 61 m (200 ft). The main haulageways were driven parallel to the ore/footwall contact in the hard cow petent graywacke wherever possible. On the lower levels, deeper into the footwall, naked development was common. This material graded into roof bolting ground towards the upper stratigraphic portion. As drifting progressed further into the upper stratigraphic portion of the footwall, progressively stronger steel sets had to be used. From the main haulageway, cross-cuts were turned into the orebody on 61 m (200 ft) centers and extended as far as needed to recover the ore available to that particular cross-cut. The main haulageways and cross-cuts were driven 3 m (10 ft) high, 3 m (10 ft) wide at the top and 4.6 m (15 ft) wide at the bottom. This configuration would accomodate a set composed of a 2.7 m (9 ft) cap on top of two 2.7 m (9 ft) legs angled out at 18'. A sill plate was used under each leg to prevent its sinking into the ore below. The type of steel used was dependent on the expected weight to be experienced. Sets were placed on 1.63 m (5 ft 4 in.) centers; however, in extremely heavy areas, it was sometimes necessary to install sets on 0.8 m (2 ft 8 in.) centers. On the top two levels (5th and 6th), the ore was considerably hard-er and was mined by sub-level stoping and long hole drilling. Very light steel sets were used in the main haulageways and cross-cuts and timber was used in the production drifts. Some con- crete production drifts were installed on 6th level, but proved to be uneconomical. However, as mining reached greater depths, the ore became softer and more massive, reaching its maximum vertical heights on 11th and 12th levels. On levels 7 through 10, yielding steel sets were used extensively in the slusher drifts. While they were satisfactory on 7th and 8th levels, their success diminished with depth and they were

Jan 1, 1981

By Henry Louis

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).—In this paper Mr. Simons derives the various forms of revolving slime tables, of which the Harz and the Linkenbach tables are typical examples, from the old rectangular or box buddle. This I believe to be an error, at any rate if Mr. Simons attaches the same meaning as I do to the ((evolution" of a dressing appliance. By the '(evolution" of such an appliance I understand the progressive development and improvement of an appliance acting on a definite principle, such improvements having usually for their object the economy of labor in working the same, or the increase of its capacity; when an entirely new principle is introduced, I no longer look upon this as evolution from the old type, but as the origination of an independent type of appliance. The box buddle was no doubt the predecessor of the old Cornish round buddle, which was evolved from it with the object of saving the labor required to work the box buddle; both machines are horizontal-current separators, in which the separation of sands of different densities is effected by their differential rates of fall in a horizontal current of water of considerable depth. These appliances, though well suited to sands, are for obvious reasons not adapted to the treatment of slimes. The revolving tables of the Harz and similar types, on the other hand, act on the principle which I have called separation in thin films of water, and which Mr. Simons calls the film sizing principle, in which the resistance of the surface over which the pulp flows plays an essential part in determining the separation of the particles, and which is well suited to the treatment of slimes. Unlike the last principle, it will not work in deep bodies of water and cannot be used where considerable depth of material accumulates in the appliance, as in the box buddle and round buddle. As I have shown in my book, The Dressing of Minerals, p. 326, these revolving tables are a development of the appliance known variously as the flat buddle, flat table, or frame, the last name, which is the old Cornish one, being the one that I personally prefer. These primitive appliances, as well as the continuous-acting round tables described by Mr. Simons (his Figs. 10 et seq.) all work on the principle of separation in thin films, and are all adapted for the treatment of slimes; his buddles and round tables (Figs. 1 to 9) do not work upon this principle, and should therefore be sharply differentiated from the former. The evolution in each case of the continuous acting, more or less automatic, circular appliance from the primitive, intermittent, hand-worked, rectangular appliance has proceeded upon strictly parallel lines. The question of the evolution of the respective types involves a point of some importance as regards the principles of ore dressing.

Jan 1, 1915

By C. R. Whitney, G. N. Maniar, D. R. Muzyka

Previous results have shown that Pyromet 860, an Fe-Ni-base heat-resistant alloy, is stable at temperatures as high as 1500°F for aging times as long as 100 hr. This Paper describes the results of long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Times as long as 37,660 hr were employed. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffraction, and microprobe techniques. phase, containing cobalt, nickel, and molybdenum, was detected after extended exposures from 1200" to 1400°F and careful study was performed to describe the kinetics of its formation in this alloy. µ phase formation apparently has little effect on the elevated-tem-perature properties of Pyromet 860. For times as long as 500 hr at 1300°F and below, with µ phase present, m significant effects on ambient temperature properties were noted. For longer times at 1300°F and after 1400°F exposure, the effects of u phase on ambient temperature tensile strength properties are not clear due to y' effects and grain boundary reactions. Electron-vacancy, N,, numbers were calculated using different methods described in literature and correlated with the present findings. In the selection of alloys for use in gas turbine applications, structural stability ranks as a primary criterion. High-temperature strength and cost are also of major concern. With these factors in mind, Pyromet 860 alloy, an Fe-Ni-base superalloy was designed. This alloy combines the cost advantages of Fe-Ni-base alloys such as A-286, 901, and V-57 with improved strength and structural stability'1,2 and no tendency to form the embrittling cellular 77 phase. A previous study3 reported on the stability of Pyro-met 860 at temperatures from 1375" to 157 5°F and times up to 100 hr. That study showed that the y' precipitates increased in size and separation and decreased in number with an increase in time or aging temperature. No deleterious phases were found to occur. In the present work, samples from four production heats were subjected to long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Various heat treatments were used on the starting samples and tests were run up to 37,660 hr. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffrac- tion, and microprobe techniques. Electron vacancy numbers, Nv , calculations were made by TRW.4 Experimental results are correlated with the Nv data used to predict occurrence of intermetallic phases such as a phase. EXPERIMENTAL PROCEDURE Mechanical Tests. Material for the present study came from four production size heats of Pyromet 860 alloy, weighing from about 3000 to about 10,000 lb. All of these heats were made by vacuum induction melting plus consumable electrode vacuum remelting. The nominal analysis for this alloy is compared with the actual analysis of the four heats in Table I. Sections of these heats were forged to 9/16-in. round bar,3/4-in. square bar, 3-in. round bar, 4-in. square bar, and a gas turbine blade forging about 16 in, long, about 6 in. wide, and weighing about 20 lb. In general, all forging of this alloy is done from a 2050°F furnace temperature. Longitudinal test blanks were cut from the centers of the smaller bars, from mid-radius positions for the 3- and 4-in. bars, and from the air foil of the gas turbine blade and heat-treated according to the procedures outlined in Table 11. Heat treatment A is the "standard treatment" recommended for this alloy for best all-around strength and ductility. Heat treatment B is a modification of treatment A for improved tensile strength at moderate temperatures. The treatment coded C was designed for treating large sections according to a procedure previously described.' Heat treatment D was developed to yield optimum stress relaxation characteristics at 1050°F for a steam turbine bolting application. After heat treatment, the test blanks were machined either to plain bar creep specimens with a gage diameter of 0.252 in., to combination smooth-notched stress-rupture bars with a plain bar diameter of 0.178 in. and a concentration factor of Kt 3.8' at the notched section, or to notch-only specimens. All specimens conformed to ASTM requirements. Metallography. Most of the creep-rupture tests were continued to failure. A few bars were fractured as smooth or notch tensiles after creep-rupture exposures. After fracturing, ordinary metallographic sections were made primarily in gage areas adjacent to fractures to represent a "high-stress" region and through specimen threads to represent a "low-stress" region. All metallographic sections were made in a longitudinal direction with respect to the test specimen axes. For optical microscopy, the samples were etched in glyceregia (15 ml HC1, 5 ml HNO,, 10 ml glycerol). For XRD analysis, the phases were extracted electrolytically in two media: 20 pct &Po4 in H20 for selective extraction of y' and 10 pct HC1 in methanol for carbides and other phases.

Jan 1, 1970

By F. J. Plecity, W. C. Leslie, F. W. Aul

During isothermal recrystallization, the rate of grain growth in dilute Fe-hlo alloys decreased rapidly with increasing Mo content, up to -0.04 at pct, and less rapidly therea-fter. Rate of growth also decreased sharply with time at constant temperature. The observed rates of boundary migration did not cor,espond to predictions of the Lucke-Detert theory. It is proposed that the growth of recrystallized grains is inhibited by clustering of solute atoms at inzperfections in the unrecrystallized matrix. It is now firmly etablished" that the rate of re-crystallization of cold-worked metals, i.e., the rate of growth of recrystallized grains into the deformed matrix, is greatly inhibited by the presence of alloying elements in solid solution. The effect is greatest with the first very small quantity of alloying elements, and additional increments cause much less pronounced retardation of growth. The early papers on this subject were reviewed in Ref. 6. The mechanism of retardation of growth is not clear; only one theory, due to Lucke and Detert? has been advanced. This assumes an elastic interaction between grain boundaries and solute atoms which tends to increase the concentration of the latter in the grain boundaries. Except at very low solute concentrations or at high temperatures, the mobility of the boundary is assumed to be controlled by the rate of diffusion of the accompanying solute atoms. Abrahamson and Blakeney2 have noted a correlation between "recrystallization temperature of binary alloys of iron and the number of d-shell electrons in the solute atoms. There is need for considerably more experimental data on the effect of solute elements on the rate of migration of grain boundaries into the deformed matrix, to provide the basis for an understanding of the annealing process in metallic solid solutions. Only a start has been made in this direction. To avoid unnecessary complications, alloys in which precipitation does not occur should be used, but to produce the maximum effects it is desirable to select alloys with a large difference between the sizes of the atoms of the solvent and solute. For these reasons, alloys of iron and molybdenum sen for this study. MATERIALS AND PROCEDURES A 30-lb. ingot of iron and four similar ingots of Fe-Mo alloys were vacuum melted in magnesia crucibles and poured into cast-iron molds. The molybdenum contents were planned according to the results of Abrahamson and Blakeney2 sothattwoalloyswould fall in the region of rapid change of recrystallization kinetics with change in composition (0.006 to 0.015 and 0.030 to 0.045 at. pct Mo) and two alloys would fall in the region of gradual change (0.18 to 0.24 and

Jan 1, 1962

By J. J. Thomas

THIS investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. FIG. 1.-STRESS-STRAIN DIAGRAM. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 2, 1921

By M. J. Marcinkowski, D. Koskimaki, A. S. Sastri

THIS is the second in a trilogy of investigations carried out in order to understand the solid state transformations and their accompanying effects on the deformation behavior of near-equiatomic Ni-Ti alloys. The first stage of this effort has dealt with the strictly martensitic structures obtainable in these alloys, i.e., those in which diffusion processes were not involved.1,2 These martensites could be produced either by rapid quenching or by plastic deformation of the originally B2 type phase. The present investigation, on the other hand, will deal with those transformations in Ni-Ti which do involve diffusion. A majority of investigators3-10 have shown that the B2 modification of TiNi, which is stable at elevated temperatures, decomposes into one or both of the intermetallic compounds NiTi2 and Ni3Ti below about 650°C. On the other hand, this has been disputed by several Workers was undertaken in order to resolve this discrepancy, as well as to shed more light on the nonmar-tensitic decomposition of B2 NiTi. EXPERIMENTAL PROCEDURE Sample preparation, fabrication, and examination were the same as those described previously in Ref. 2. In addition to the 50 at. pct Ni (55.06 wt pct) hypoeu-tectoid alloy used previously, a second hypereutectoid alloy containing 54.4 at. pct Ni (60 wt pct) was also prepared for this study. RESULTS AND DISCUSSION The equilibrium diagram for the Ni-Ti alloy system in the vicinity of Ni-Ti is shown in Fig. 1. The solid lines have been established by the work of Poole and ~ume-Ftothery4 whereas the dotted lines are based on findings obtained in the present investigation as described below. Structure and Morphology. Fig. 2(a) shows a bright field transmission electron micrograph of a two-phase structure obtained in a polycrystalline Ni-Ti alloy that was furnace cooled (approx 200°C per hr) from 1050' to about 300°C. Large plate-shaped precipitates can be observed in a matrix which was found by electron diffraction to possess the high temperature B2 structure. A selected area diffraction pattern of the region covered by Fig. 2(a) is shown in Fig. 2(b), while Fig. 2(c) is a detailed schematic interpretation of Fig. 2(b). The B2 matrix reflections are illustrated by squares while those of the precipitate are shown as circles. The d values associated with the precipitate reflections could be determined quite accurately since the reflections from the B2 matrix, for which the lattice constant is known precisely, were simultaneously present in the diffraction patterns. All of the reflections

Jan 1, 1970

E. Hill, South Norwalk, Conn. (communication to the Secretary*) :—The phenomenon described by Dr. Ledoux, involving an apparently abnormal high temperature in the air-cylinders of compressors, has not been, so far as I know, discussed in technical literature. The common formula for the adiabatic compression of dry air does not account for heat suficient to flash ordinarily decent cylinder-oils, nor do the text-books include in their theoretical statements any quantitative consideration of the effect of leaks in the ideal machines which they contemplate. This lack I have endeavored to supply by preparing, in the form of a circular, for the use of the customers and correspondents of the Norwalk Iron-Works, a brief mathematical

Jan 1, 1904

By K. K. Rao, M. E. Nicholson

IN a recent paper on the solubility of carbon in Ni-Cu alloys,' Nicholson reported that the carbon solubility appeared to be limited by the electronic structure of the alloys and that the solubility was propor- tional to the density of states at the Fermi surface of the "3d" band. In order to determine whether or not this relationship is a general one, the study has been extended to other systems. One of these is the CO-Ni system. This system was chosen for study because 1) it is adjacent to Ni-Cu system in the periodic table, 2) the alloys of cobalt and nickel do not form stable carbides at 1000°C, and 3) the system exhibits no pronounced change (less than 1 pct) in lattice parameter from cobalt to nickel,' see Fig. 1. The alloys were prepared from -200-mesh 99.92 pct Ni furnished by the International Nickel Co. and spectroscopically pure -200-mesh cobalt sponge obtained from Johns on-Matthey and Co. The powders were weighed, mixed, and pressed using a pressure of 40,000 psi. The samples were sintered for 24 hr at 900° C in dry hydrogen and then cold rolled to a thickness of 0.010 in. (Samples containing more than 70 wt pct Co had to be annealed after cold reductions of about 20 pct to avoid cracking.) The alloys were carburized at 1000°C in an alun-durn boat containing Acheson AUC powdered graphite in an atmosphere of carbon monoxide cylinder gas which had been passed through Ascarite to remove carbon dioxide. After carburizing for either 12 or 24 hr the samples were moved to a cool zone of the furnace to cool. Cooling required about 5 min. The samples were filed to remove about 0.005 in. from the surface and then analyzed using a conventional combustion-gravimetric analytic method. The results of this investigation are shown in the lower portion of Fig. 1 and Tabulated in Table I. The nickel percentages for these alloys were determined from the weights of the powders from which the alloys were made. The solubility of carbon in pure cobalt at 1000°C (fcc) is 0.25 wt pct. This is somewhat less than the 0.33 wt pct measured by Boecker.3 From his data, it would appear Boecker's samples were supersaturated before the equilibrating treatment and that a 20-min treatment was not long enough to achieve equilibrium. Since in the present investigation the 12 and 24 treatments produced essentially equal carbon contents, our figure is presumed to represent more nearly the equilibrium value. The solubility of carbon in nickel of 0.19 wt pct agrees quite well with the value of 0.21 wt pct

Jan 1, 1963

By C. E. Siebenthal

produce attractive and consequently more salable products. It would seem, however, that if solder and babbitt were cast in closed molds, just as good practical results would be obtained by the user, without his being able to give preference to solders of unnecessarily higher grade on account of their appearance. It would be hopeless for any one. manufacturer of solder to undertake a change of this kind, but if all manufacturers of solder agreed upon it, they would be able, in my opinion, to get the users of solder to take, and to approve by their practical tests, metals containing less tin than they have been accustomed to. The same is true with regard to babbitt metals. An illustration of how, in the use of an alloy, appearance sometimes is deceptive, is to be found in the case of what may be called intermediate grades of babbitt. I am thoroughly convinced that high-tin or high-lead babbitts are better than those containing both lead and tin with relatively high percentages of each. A high-tin babbitt should not contain more than about 10 per cent. of lead, and a high-lead babbitt should not contain more than 10 per cent. of tin, unless the percentage of antimony can be correspondingly increased. The intermediate babbitts, such as those that contain from 30 to 70 per cent. of lead or tin, may give nice appearing castings that flow easily, but they have not the serviceability of the high-lead or high-tin babbitts. Their hardness diminishes very rapidly as the temperature rises, and they have a relatively low softening point due to the eutectic components present. The Cadmium Supply of the united States* C. E. Siebenthal, † Washington., D. C.—From being one of the most maligned of metals—a veritable bugaboo—cadmium has almost overnight become respectable, though its slender claim to respectability rests almost wholly on the possibility of its substitution for tin. Preliminary to any campaign for such substitution, particularly for enforced substitution, the possible supply of cadmium should be determined as closely as possible; for that reason the statistical inquiry of which this paper embodies the results was undertaken. Production Cadmium is marketed in two forms, as metallic cadmium, in sticks or bars, and as cadmium sulfide, the pigment. The metal has found its greatest field of use in this country as a component of an easily fusible alloy that is used in automatic fire extinguishers. The sulfide is used to some extent in paints but chiefly to give color and luster to glass and porcelain. The metal was first made in this country by the Grasselli Chemical

Jan 1, 1919

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler's saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By L. Grånäs, B. Aronsson

In a recent study of Fe-Si alloys Walter and Koch' observed pairs of dislocations in Fe-6.25 pct Si crystals rolled to reductions of 10 pct and subsequently annealed for 1 hr at 650°C. They interpreted these pairs as being due to stacking faults. From the spacing of the dislocations a stacking-fault energy of 15 to 19 ergs per sq cm was calculated. These authors did not pay any attention to the order -disorder phenomena in Fe-Si alloys. It is the purpose of this communication to report some preliminary results from a study of ordering and its influence on the plastic deformation of Fe-6.0 pct Si alloys. Our results suggest that the dislocation pairs observed by Walter and Koch may have been due to long-range order rather than to stacking faults. The alloys used in this investigation were prepared from pure electrolytic iron and silicon and were melted in argon. After hot working, strip tensile specimens were machined to a gage length of 70 mm and a thickness of 1 mm. The specimens were heat- treated for 2 hr at 1000°C, furnace-cooled, and subsequently deformed 2 pct in tension at 400°C. The strain rate was 5.6 X lo-' sec-'. Thin foils of the deformed specimens were prepared by means of the Bollman technique and examined in a Siemens Elmis-kop I at an accelerating voltage of 100 kv. In the Fe-Si system long-range ordering occurs at a silicon content of about 6 pct Si. In our alloys evidence for ordering is given by selected-area diffraction patterns which show extra reflections consistent with a super lattice of the D0 9 type. In addition, the dislocation arrangement in deformed specimens indicates that long-range order is present. A typical mi-crophotograph of a thin foil is shown in Fig. l. The dislocations are usually straight and parallel and laying in distinct directions. In the commonly observed (111) zone the projections of the dislocations are close to (113) and (oil). Observation of the image position indicates that the two dislocations in a pair have the same Burgers vector and hence constitute a superlattice dislocation.~ According to theory3 a superlattice dislocation in the DO3 structure consists of four ordinary dislocations connected by two types of antiphase boundaries as shown in Fig. 2. In our specimens only two dislocations in each pair have been observed, Fig. 1. The problem is to decide whether the area between these is a NN or a NNN antiphase boundary. Dark-field images using the (200) reflexion (the indices are defined with respect to the DO3-type superlattice) can

Jan 1, 1968

By H. B. FERNALD

THE interesting and carefully developed formula which Professor Bucky presents for answering the question of whether proposed new equipment will give a net return on investment equal to or greater than that on present equipment starts with an assumption that the management may make this relative return a determining factor in its decision whether or not the new equipment should be provided. I do not question that in some cases the management may take this position, but I would point out the error involved in so doing. The proper test is not a comparison of the return on new as compared with the return on old investment, but is rather a comparison of the return on a particular new investment as compared with the return which would be obtainable from some other new investment which now might be made. Then I would point out that I believe Professor Bucky is in error in using as a factor in his computations the item of unamortized cost of old investment. The financial advantage to be derived from a new investment does not depend on the extent to which we may in the past have written off the cost of old equipment, nor does it even depend upon what was the original cost of that old equipment. Even the salvage or resale value of the old equipment will only enter into the picture to the extent that the present salvage or resale value differs from the ultimate salvage or resale value otherwise to be obtained, after due allowance for the interest factor.

Jan 1, 1930

By Sherwin F. Kelly

GEOPHYSICS may be considered a vice (albeit, I submit, a comparatively harmless one) whose career is aptly described by Pope's lines: Vice is a monster of so frightful mien, As to be hated needs but to be seen; Yet too oft, familiar with her face, We first endure, then pity, then embrace. Although there may be some that have not yet succeeded in emancipating themselves from the first stage of horrified contemplation, geophysicists may be duly thankful that there are mining men and geologists that have arrived at a state of apparently irretrievable damnation.

Jan 1, 1936

By ANDREW McVILLIAM, WILLIAM H. HATFIELD

AT the 1902 May meeting of the Iron and Steel Institute, the, authors presented a paper on " The Elimination of Silicon in The Acid Open-Hearth," wherein they recorded a few typical examples of certain Siemens charges out of a very large number specially watched for the purposes of that research. The main deductions drawn from those experiments have been accepted in all the intelligent criticism during or after the discussion on the paper. One opinion, however, was rigidly held by all who mentioned the matter, with the single exception, perhaps, of Mr. Lange, and that was the necessity for the attainment and the maintenance of an abnormally high temperature in order that the percentage of silicon in the metallic bath might increase, or that an unusually large proportion of silicon might be retained in the metal. The original decision was ar-rived at on the results of scores of trials, and has since been the subject of frequent experiment. The authors still retain their opinion that although, naturally, a higher temperature will accelerate the (probable) action between the carbon of the steel and the excess silica of the slag, they then fairly proved, and have now abundantly confirmed the fact, that around the temperatures occurring in Siemens steel-making practice the chemical composition of the slag, particularly with regard to its acidity, is the factor which determines whether the percentage of silicon in the molten steel shall increase or decrease. In the discussion in 1902 Mr. Saniter called attention to Mr. H. H. Campbell's work, and in the reply the authors also mentioned that of Messrs. Winder and Brunton of 1892, the two

Mar 1, 1905

By C. C. Harris

This article presents a general equation describing the xYt surface in batch grinding. This equation contains as special cases most of the relationships which have been deduced from kinetic studies. In an earlier paper an analytical solution of the integro-differential equation of batch grinding was proposed1 as a first approximation of the xYt surface.' A more general equation will be presented here, which appears to combine in a single statement many conclusions reached by experiment. A possible underlying mechanism is that the changing product fineness leads to changes in the particle crushing strength and in the probability of encounter with the crushing media.

Jan 1, 1969