Search Documents

By G. Derge

The chemical and physical propertties of slag systems are of special interest to metallurgists, for nearly all metals are in contact with molten slags during the primary reduction from their ores and then during the subsequent refining and alloying processes that determine their ultimate use. These processes are carried out at high temperatures and involve such complex chemical systems that funda-mental scientific knowledge of the Properties and behavior of these slags is inadequate. Various hypotheses have been Proposed to explain known slag characteristics. The commonest of these regard the molten slag as constituted of compounds that are dissociated in varying degrees into their constituent oxides, as illustrated by Schenckl and the recent Papers of Chipman and co-authors. Another proposal is that these compounds dissociate by com-plete6 or partial ionization, the evidence for which has been reviewed by Martin and Derge.? whatever hypothesis is favored, the exact formulation of these compounds is incomplete. It is based on three principal types of information: 1. Studies of solidified 51% samples by X ray diffraction, petrography, and similar methods that can be used at room temperature. The correlation of this information with the high-temperature properties of the molten slag is uncertain. 2. Studies of slag-metal equilibria, which have the advantage of providing observations on the molten slag at high temperature. However, even these data present problems of interpretation because they require a complete knowledge of the metal phase. 3. Direct measurements of properties of molten slag at the temperature of greatest metallurgical interest. Viscosity, electrical conductivity, specific heats, and similar properties have been measured, but the data of this type are widely scattered and frequently difficult to interpret. Additional direct measurements of properties of molten slag that can be interpreted in terms of chemical behavior are required, and this paper shows that the standard physical-chemical measurement of reversible electrode potentials, which measure the activity of specific constituents, is a fruitful source of such information. The purpose of this investigation, therefore, was to find an electrode combination that would yield reversible electromotive force measurements when dipped into the molten slag to be studied. Slags of the systems cao-sio2 and cao-120,-SiO2 were chosen for study because graphite containers could be used and the data could be correlated with those for viscosity, conductivity, and other proper-

Jan 1, 1948

By Michael B. Bever, Carl F. Floe

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By Carl F. Floe, Michael B. Bever

The solubility of hydrogen in molten copper-tin alloys is of both practical and theoretical interest. From a practical standpoint, data on the equilibrium solubility as a function of temperature, pressure and alloy composition are valuable for a better understanding of porosity problems in bronze castings. From the theoretical point of view the determination of the hydrogen-copper-tin equilibrium is of interest since it extends the laws governing the solution of gases in metals. This paper presents the results of an investigation of the solubility of hydrogen in representative compositions of the copper-tin system at temperatures ranging from above the liquidus to I300°C. and at pressures from less than 50 mm. of mercury to about atmospheric. Review of Previous Work The solubility of hydrogen in copper was determined by Sieverts and Krumbhaarl in 1910 and by Roentgen and Moeller2 in 1934. Their values are in fair agreement. In 1926 Iwasé3 reported results that were very much higher. The published data on the solubility of hydrogen in tin do not agree. Smithells4 states that no reliable data are available According to Sieverts and Krumbhaar,5 hydrogen is insoluble in tin. Bircumshaw,6 on the other hand, found a definite solubility at 800°C. The latter's experimental procedure did not provide for stirring of the metal and in his opinion he failed to reach equilibrium. Iwasé3 again reported large solubility values. For copper alloys, Sieverts and Krumbhaar5 distinguished between alloying elements that do not markedly affect the solubility of hydrogen, elements that increase the solubility, and elements that reduce it. They named gold, tin, and aluminum as examples of this last group and reported hydrogen solubility data at 1225°C. for the copper-rich side of these alloy systems at atmospheric pressure. Without giving experimental results, they stated that the amount of hydrogen dissolved by liquid copper alloys is proportional to the square root of the pressure as in pure metals. These authors suggested that in a limited way the effect of an alloying element on the solubility of a gas is related to the constitution diagram for the alloy system. Sieverts7 also called attention to the fact that the curve of hydrogen solubility versus composition of copper-tin alloys shows a sharp change of direction at the composition of Cu3Sn and suggested that this compound persists at least to some extent in the molten state. Iwasé3 reported large hydrogen solubility values for several compositions of copper-tin alloys, which appear to be in error.

Jan 1, 1944

By Murray F. Hawkins

Horner1 and van Everdingen8 ave shown that the pressure drop within the wellbore, as a result of having produced the well at a constant rate q for time t, where t is sufficiently large, is: van Everdingen observed that better agreement between theory and well performance can be obtained if, instead of assuming the permeability is kc everywhere about the well, it is assumed the permeability near the well-bore is substantially reduced as a result of drilling, completion and/or production practices. In order to account for the additional pressure drop he introduced the dimensionless quantity S, the skin effect factor, so that Eq. 1 becomes: Eq. 2 might have also been obtained as follows. Assume a zone of altered permeability k, exists about the well out to a radius r and beyond that the unaltered, external permeability k. The additional pressure drop required to overcome this skin of reduced permeability may be calculated with sufficient accuracy using the incompressible flow equation; for Browns-combe and Collins1 have shown almost no difference between compressible and incompressible steady-state flow, in the vicinity of the wellbore, and the small volume of fluid in the vicinity of the wellbore makes unsteady-state mechanics unnecessary. Then. The sign of this skin pressure drop will be positive or negative depending upon whether the altered permeability k, is smaller or larger, respectively, than the external permeability k... Adding the pressure drop of Eq. 3 to Eq. 1 to find the total pressure drop: Comparing Eq. 4 with Eq. 3 it is seen that the skin effect may be defined by: be determined from pressure build-up tests1,3,4,5,6,7,8 The average permeability kavg including the altered and external permeabilities, can be determined from PI tests, and may be defined approximately on the basis of steady-state flow, as was done by Thomas' in defining the damage factor, by: The productivity ratio is the ratio of the average to the external permeability, kavg/ke or This equation shows that the productivity ratio and the skin effect are not uniquely related, because of the uncertainty in the drainage radius, and also, in many instances, the wellbore radius. Fortunately, they enter in the logarithm. The curves of Fig. I are plots of Eq. 8 for values from 100 to 50,000. The points represent the skin effects and corresponding productivity ratios from a large number of well tests, taken from Fig. 15 of Ref. 5 or Fig. 13 of Ref. 9. While some of the data

Jan 1, 1957

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale); Condition C (Rolling Sandstone with Shale in Pockets); and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were wed to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 12, 1978

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for Predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale); Condition C (Rolling Sandstone with Shale in Pockets); and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1979

By Kendall E. Born

Production of crude oil in Tennessee during 1942 was approximately 8600 bbl., a decrease of 6500 bbl. from the production of 1941, and the lowest since 1934. As usual, the greater part of the production was from the Mississippian limestone pools in Scott and Morgan Counties. Some half dozen wells in Fentress and Clay Counties pumped intermittently produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas respectively. Figures are not available for the Morgan County production but 7,378,000 cu. ft. of natural gas was produced in the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Developments Drilling activities reached the lowest ebb since 1933. Only 10 wells were spudded during the year, one of which was drilling on Dec. 31, 1942. Of the nine completions, two were gas wells in the proven area south of Jamestown in Fentress County and seven were dry holes. The total footage drilled during the year was 14,198 ft.; the average depth of wells was 1578 ft. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 4219 ft., the second deepest well in the state, in Campbell County. The test was in the highly disturbed Valley and Ridge Province, an area long considered the most unfavorable in the state for the accumulation of oil and gas. Cumberland Plateau.-—There were no completions in the Cumberland Plateau area, although an old well drilled deeper found oil from 935 to 965 ft. in the Mississippi lime. This test has created a considerable amount of interest in the area and an active leasing campaign was underway early in 1943. Eastern Highland Rim.—Five completions on the Eastern Highland Rim brought in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area were drilled to the upper part of the Knox dolomite group. The most significant test during the year was the Stanolind Oil and Gas Company's test in Putnam County. This well, on a well-defined surface structure, was abandoned in the upper Knox dolomite group at 2130 ft. A show of oil was logged in the Knox at 1653 to 1661 ft. Northern Highland Rim.—Three tests widely separated in the Northern Highland Rim were dry.

Jan 1, 1943

By Kendall E. Born

Production of crude oil in Tennessee during 1942 was approximately 8600 bbl., a decrease of 6500 bbl. from the production of 1941, and the lowest since 1934. As usual, the greater part of the production was from the Mississippian limestone pools in Scott and Morgan Counties. Some half dozen wells in Fentress and Clay Counties pumped intermittently produced about 1000 barrels. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas respectively. Figures are not available for the Morgan County production but 7,378,000 cu. ft. of natural gas was produced in the Jamestown gas field from six wells. The production of oil by counties is shown in Table I. Developments Drilling activities reached the lowest ebb since 1933. Only 10 wells were spudded during the year, one of which was drilling on Dec. 31, 1942. Of the nine completions, two were gas wells in the proven area south of Jamestown in Fentress County and seven were dry holes. The total footage drilled during the year was 14,198 ft.; the average depth of wells was 1578 ft. The completions are listed in Table 2. The distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 4219 ft., the second deepest well in the state, in Campbell County. The test was in the highly disturbed Valley and Ridge Province, an area long considered the most unfavorable in the state for the accumulation of oil and gas. Cumberland Plateau.-—There were no completions in the Cumberland Plateau area, although an old well drilled deeper found oil from 935 to 965 ft. in the Mississippi lime. This test has created a considerable amount of interest in the area and an active leasing campaign was underway early in 1943. Eastern Highland Rim.—Five completions on the Eastern Highland Rim brought in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area were drilled to the upper part of the Knox dolomite group. The most significant test during the year was the Stanolind Oil and Gas Company's test in Putnam County. This well, on a well-defined surface structure, was abandoned in the upper Knox dolomite group at 2130 ft. A show of oil was logged in the Knox at 1653 to 1661 ft. Northern Highland Rim.—Three tests widely separated in the Northern Highland Rim were dry.

Jan 1, 1943

By Nicholas J. Grant, Olaf Troili, John Chipman

IN recent studies of the factors which affect the rate of desulphurization and its equilibrium, it became apparent that certain concurrent reactions were operative which had a significant effect on desulphurization. This is emphasized in the experiments of Hatch and Chipman1 and of Grant, Kalling, and Chipman' by the slow approach to a final state of equilibrium which is in marked contrast to the initial rapid transfer of sulphur from metal to slag. Since the removal of sulphur is of such profound importance in iron and steelmaking, it appeared necessary to investigate the reactions responsible for this behavior. It is now known that the presence of iron oxide in the slag interferes seriously with the principal reaction of blast-furnace desulphurization: CaO (slag) +-S + C - CaS (slag) + CO [l] The interfering reaction is most simply expressed as: CaS (slag) + 0 = CaO (slag) +-S 121 and a small concentration of oxygen (or FeO) is sufficient to hold a considerable amount of sulphur in the metal. It has been shown by Grant, Kalling, and Chipman2 that the addition of MnO to blast-furnace slag slows the removal of sulphur from the metal. This effect overshadows the contribution of MnO to basicity and is ascribed to its oxidizing power. It will be shown in this paper that SiO, also has sufficient oxidizing power to interfere with blastfurnace desulphurization. This is, of course, only one of its several effects. Primarily it is an acid and therefore reduces the concentration of excess lime. But when silicon is reduced to the metal the oxygen to which it was previously bonded becomes in part available for reaction 2. The proof of this statement is found in the following experiments. Experimental Procedure and Results Utilizing the same procedure and apparatus described by Grant, Kalling, and Chipman' five additional heats were made using slags IV and 11, the starting compositions of which were: slag IV—40 CaO, 10 MgO, 35 SiO,, 15 A1,0,; and slag 11—50 CaO, 10 MgO, 25 SiO,, 15 Al3O3. An important difference between these heats and those previously reported was that silicon to the extent of 1 to 4 pct was added to the present heats whereas the starting silicon content was formerly about 0.2 pct. Table I shows the slag and metal analyses for heats 82 to 87, and Table I1 shows the silicon addi- tions made to the charge. These additions are based on 400 g of metal and 400 g of slag. All heats had 1.65 400pct S charged before the cold slagadditions. The temperature was maintained at 1525°C. Rate of SiO, Reduction: Fig. 1 shows the silicon content of the metal in contact with slag IV at 1525°C as a function of time. Heat 70 from the work of Grant, afunctionKalling,of and Chipman is included as the lowest starting silicon. It will be noted that eeven with 4 pct Si in the starting metal, there is an increase in silicon content with time. Heat 84 is apparently approaching silicon equilibrium very slowly. Heats 70 and 82 with very much lower slowly.starting silicon show a more rapid initial rise in startingsilicon content but do not reach equilibrium during a long holding period. Fig. 2 shows 3 different initial silicon contents for Fig.2shows3differentheats 73 (from Grant, Kalling, and Chipman) 86 and 87, in contact with slag II, the most basic slag. Heat 73 is increasing in silicon with time, whereas heat 87 with an initial silicon content of 3.7 pct shows a decrease with time. Heat 86 shows a very close approach to equilibrium. The rate of transfer of silicon from slag to equilibrium.metal is very slow in all of those heats, even those which are initially far from equilibrium. ____

Jan 1, 1952

H. M. HOWE, Bedford Hills, N. Y.-We may clear the matter very easily, at least to a very great extent, if we look at these islands of ferrite that occur in steel castings as simply corresponding to the ferrite ghosts in steel forgings, representing the differentiation that takes place in the solidification off the molten mass. In that solidification you have dendritic crystals forming and in between those dendrites you have con-

Jan 12, 1919

By Carville E. Sparks, Rollin Farmin

TRIAL installations of rock bolts, of the slit-rod- and-wedge type, were under way at several units of Day Mines, Inc., when Korean hostilities interrupted the already slow deliveries of steel bars to the Coeur d'Alene district. Factory-made bolts had not yet been put on the local market, so the program was halted for lack of supplies. Interest was revived by a visitor's description of wooden roof bolts. These were said to have been used briefly with apparent success in a coal mine, until apprehension voiced by the U. S. Bureau of Mines caused the practice to be suspended

Jan 9, 1953

The Nominating Committee desire to submit the following nominations. President and Director: SIDNEY J. JENNINGS District 0 Vice-President and Director: H. S. DRINKER District 2 R. M. RAYMOND District 0 Directors: G. C. STONE District 0 HENNEN JENNINGS District 9 S. A. TAYLOR District 2 F. G. COTTRELL District 6 ARTHUR THACHER District 3 These nominations were unanimous. By order of the Committee J. V. N. DORR, Chairman. Oct. 10. 1917.

Jan 12, 1917

By D. M. Buck

D. M. Buck, * Pittsburg, Pa.-During the first 5 months of 1918, approximately 11,000,000 lb. per month of pig tin were consumed in the United States. Solder, hearing metals, bronzes, etc. used about 5,500,000 lb.; collapsible tubes a little more than 250,000 lb.; tin-foil about 500,000 lb.; and the tin- and terne-plate industry somewhat less than 5,000,000 lb. In an effort to reduce this consumption and thus conserve our tin supplies, several methods of procedure suggest themselves: 1. Salvage. The most careful and systematic collection and re-use

Jan 12, 1918

By H. Foster Bain

Jan 1, 1910

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By Gray L. L., Max Littlefield, Godbold A. C.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948

By Max Littlefield, Godbold A. C., Gray L. L.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948