Search Documents

By E. P. Whelan

A recent investigation1 into the origin of "ghost boundaries" in dilute Cd-Mg alloys has indicated the persistence of a segregated solidification substructure in spite of a homogenizing treatment designed to remove such segregation. Although no grain growth experiments have been reported on these segregated alloys, the homogenizing treatment used in grain growth studies on other dilute alloys2-7 is similar in

Jan 1, 1968

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By G. E. McElroy

MUCH attention has been directed to mine-air flow in recent years, more especially in Great Britian where there is frequent reference to a theory of fluid flow developed by English engineers. Briefly stated, this theory is that for similar passages of the same relative roughness, in which fluid flow occurs, the conditions of flow are exactly the same for equal values of the product W D V/ µ, where W = density of the fluid, D = diameter of the passage through which flow occurs, V = mean velocity of flow, and µ = absolute viscosity of the fluid flowing. This, the "Reynolds Criterion" of fluid flow, had its origin in the work of Prof. Osborne Reynolds&apos; more than 40 years ago. Later, Lord Rayleigh amplified the theory2 which has been conclusively proved for small pipes by the experiments of Stanton and Pannel3 over a large flow range, and by Lacey4 over a somewhat more limited range. Concordant results on small pipes have also been obtained by numerous other investigators with single fluids over more or less limited ranges of flow. According to this theory results in one medium, such as water, are immediately applicable to another, such as air; and experimental results on models are (theoretically, at least) applicable to full-scale designs. This is of great importance in aeronautics and can be of considerable value in mine ventilation research. Hodgson, in a recent paper,5 has outlined the application of this theory to mine-air flow and recent English experiments" on the resistance of a timbered mine airway have been expressed in this form.

Jan 10, 1926

By John Johnston

WHEN I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe&apos;s book, "The Metallography of Steel and Cast Iron," published in 1916-that is, about 25 years ago-in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father Dr. Samuel Gridley Howe, his mother Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe&apos;s writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-carbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand&apos; truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable, tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half¬initiated from misusing it and the uninitiated from being misled by these misuses," he writes-and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. It tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to decipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By Marston G. Fleming

E. C. Peterson (Anaconda Copper Mining CO., Darwin, Calif.)—A study of this quite comprehensible and interesting paper by Dr. Fleming brings to mind several observations in the practical application of alkalinity and related factors to the actual practice of lead mineral flotation. Soda ash has long been a widely used and a very helpful alkaline conditioning agent in the flotation of galena from the usual run of lead-zinc ores. Soda ash is one of the common "standard" conditioning agents tried in any laboratory investigation of lead-zinc ores because it has so often proved helpful to galena flotation. However, the use of soda ash in the actual flotation of oxidized lead ores is certainly not widespread. In the flotation of certain lead-zinc ores from the Park City district of Utah, it was found in the usual cyanide-zinc sulphate-xanthate circuit that soda ash had an effect of producing a very condensed and flat froth regardless of the many frothers tried and that substitution of lime for soda ash to produce the same pH (8.0 to 8.4) improved the froth condition. However, the flotation of coarse particles of galena became so critical that some would pass through into the tailing, but caustic soda as a substitute for either soda ash or lime produced a very desirable froth condition in the same pH range and greatly improved the metallurgical outcome. Milling was carried out in typically "hard water" from watersheds of limestone and other calcareous rocks and the ore also apparently contributed magnesium and calcium salts to the pulp. Certain lead-zinc ores of Mexico have shown their greatest flotation response in circuits conditioned with sodium bicarbonate, and such actual mill use was also believed to be related to the water necessarily used in milling. On other lead-zinc ores the optimum has been obtained in actual milling treatment by use of caustic soda in both circuits of the operation. In flotation of oxidized lead ores in which sulphidi-zation is employed by addition of sodium sulphide, very high pH&apos;s exist in the flotation circuit. With the usual oxide lead ores, demanding 5 to 15 lb of sodium sulphide per ton of ore, pH&apos;s in the circuit (closed and open water-circuits) may range from 9.5 to 12, and for ores that contain much anglesite or a high percentage of iron oxide minerals, sodium sulphide consumption may reach as much as 30 lb per ton of ore and the resultant pH will be correspondingly higher. Yet in such flotation treatment employing either xanthate or oil (high-sulphur crude oil or diesel oils) as the collector, satisfactory to excellent grades of concentrate and lead recovery are obtained. Although there have been great studies and accomplishments in the investigations of flotation fundamentals and flotation theory, and although an investigation to determine the effect of all factors entering into the actual plant flotation of sulphide and oxide ores must become very complicated, as Mr. Fleming has mentioned in his caution regarding the drawing of general conclusions for other ores, it seems that it would be of greater interest if the techniques and investigations could, with time, approach the conditions of actual practice and lead the way to improved and more efficient flotation plant performance. Marston G. Fleming (author&apos;s reply)—The gulf between fundamental flotation research and plant operation is, perhaps, less wide than Mr. Peterson suggests. For example, the work described in my paper developed from an extensive investigation of a complex lead-vanadium ore from southwest Africa. This investigation started as a standard ore-testing problem but, at almost every stage, results were obtained which could not be interpreted in terms of previous experience. A program of fundamental research was therefore undertaken and was closely interlocked with the ore testing. This coordinated investigation resulted in a flotation process which has now been proved by two years of successful plant operation, and although the grade and mineralogical constitution of ore as well as smelter requirements have altered more than could have been anticipated, our knowledge of the fundamental character of the problem has made it possible to meet each change in conditions with much more confidence than would have been the case had we neglected this aspect of the investigation.

Jan 1, 1954

By Russell G. Wayland

SINCE the installation at Kropfmuehl, Bavaria, of a modern flotation concentrator in 1938, the flake and fine graphite from the Passau area can now be delivered in about any normal specified carbon content of any size range up to a flake averaging about 0.7 mm. The graphite finds a wide German and export market for crucible manufacture, pencil leads, dry cells and other uses.

Jan 2, 1951

By John Johnston

WHEN I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe&apos;s book, "The Metallography of Steel and Cast Iron," published in 1916-that is, about 25 years ago-in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father ¬Dr. Samuel Gridley Howe, his mother-Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe&apos;s writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature. is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-carbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable, tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass . . . by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes-and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. It tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works "f the watch was the best butter. If the reader learns no more than to beware of attempts to decipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By M. Bevis, A. G. Crocker

A. G. Crocker and M. Bevis (Battersea College of Technology)— Richman and Richman and conard17 have recently published the very interesting results of their studies on the plastic deformation of Fe-Ni-C martensites and of an Fe-5 wt pct Be alloy. Other work on the range of Fe-Be alloys containing between 16 and 27 at. pct Be has also been reported by Richman." One of the fascinating features of this work is that the materials investigated deform primarily by means of twinning and that several twinning modes are operative in addition to the well-established (112 ) mode of bcc materials The composition planes of these unusual twins were determined using a single-surface analysis and reported as (0131, "{045)" or "{089)", and It is now thought1&apos; that the "{0,1,13)" habit reported for the Fe-Ni-C alloys&apos;&apos; is more likely to be near "{127)". Although the full twinning elements of these unusual twinning modes could not be determined directly from the experimental results, the authors attempt to deduce the elements by considering twin intersectionslQ and by using the projection technique of Jaswon and Dove. The basic assumption of their approach is that the (013) habits are truly rational planes but that the other habits are irrational and merely approximated to by the indices quoted above. They thus deduce that the twinning mode describing the (013) habit is either Type I or compound and that the modes describing the other habits are Type 11. This deduction must however be false as all twinning modes in cubic structures obeying the classical orientation relationships of deformation twinning must be compound. Type-I and Type-I1 modes can occur in all of the other crystal systems (indeed in the triclinic system compound modes are not allowed), but in the cubic system only compound modes can arise. This fact, which does not appear to be well-known, fol- lows immediately from the relations between the four twinning elements defining a twinning mode. Thus for a Type-I mode which is uniquely defined by the rational twinning elements K1 = hi and given by: where the summation convention of the tensor calculus has been adopted. For cubic materials the metrics and reduce to the unit tensors and j so that we have It is clear from these equations that both ki and ui must take on integral values; i.e., Kz, and ql must be rational, if hi and vi are integers, i.e., if K1 and are rational. Thus for cubic materials a Type-I mode must degenerate into a compound mode and the same result also arises for Type-II modes. The apparently irrational habits observed by the authors can thus not be explained in terms of Type-I1 twinning if the classical laws of deformation twinning are to be obeyed. An alternative explanation of the irrational habits is that they may arise from twinning modes with four irrational twinning elements. These modes, which do not obey the classical orientation relationships associated with deformation twinning, have been shown to arise as the result of double twinning processes in magnesium,22 but may also describe a simple shear on an irrational plane in an irrational direction. Indeed double twinning processes in bcc

Jan 1, 1963

By John Greenawalt

IN view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by com-bustion within the mass itself. Its first successful application, in connec-tion with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremen-dous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blown off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for ignit-ing purposes.

Jan 1, 1938

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

In the special number of the magazine Ocl und Kohle (Oct. 22, 1940) dedicated to the petroleum industry of southeastern Europe, there appeared several articles relating to Yugos1avia.t In the first article the author calls attention to the fact that there are two fields in Yugoslavia that have been explored and exploited by more than 100 wells at variable depths during the last 50 years. These are on the Island of Mura, at the confluence of the Mura and the Drave. Additional exploration drilling in various other parts of the country has been without result, but certain ones of these explorations have revealed the existence of gas horizons that have some value, which are being used for industrial purposes. Table I shows the production of oil and gas between the years 1900 and 1939. TaBle —Production of Oil ad Gas in Yugoslavia . n,i Natural Natural Years oil Years Gas, Cu. Years Gas, Cu. Meters Meters T900-1929 10,000 1923 507,000 1934 1,388,000 1930 277 1924 567,000 1935 1,401,000 1931 202 I92S 691,000 I936 1,483,000 t932 289 19261 1.472,000 1937 1,841,000 1933 629 1927! 1,732,000 193s 2,431,000 1934 324 1928 2,515,000 1939 2,628,000 1935 260 1929 4,700,000 1936 137 I93O 5.345,200 1937 463 1931 6,376,153 1938 1,091 1932 1,661,737 1939 1,114 1933 959,574 The number of wells drilled from 1884 to the present time was in the neighborhood of zoo and the total footage drilled was 65,000 m. up to July I940 They may be divided roughly as follows: 12 wells in the region produce natural gas; 134 wells in the two old fields of the Island of Mura and about zo wells for the exploration of the zone of the Flysch, in Bosnia. The depths of 50 of these wells was roo to 200 m.; the depths of 50 wells oil the Island of Mura ran from zoo to 500 m.; of 2 ; wells, 500 to I000 m.; of ro wells from rooo to 2000 meters. The deepest well drilling in Yugoslavia has reached 2000 in. In the Valley of Morave, in the region of Selnica, I00 km. south of Nish, there have been discovered asphalt-bearing limestones, which contain about 15 per cent asphalt and are associated with bituminous clays. Later, at Paclenica, important deposits of natural gas were found. A zone rich in gas and oil seepages runs through Pracec, Miklenska, Bujavica, etc. The author studied these regions from the point of view of stratigraphy and tectonics. The anticlines and gas-bearing domes are concentrated in two zones: the region of the Drave (Island of Mura) and the region of the Save, southeast of zagreb, which contains the gas field in exploitation in the region of Bujavica. A full description of the productive region of the Island of Mura has been given by Egon Bohm, a geologist, in the second article mentioned. This includes a history of the exploration and exploitation that took place under Hungarian rule in this region. The most important exploration was effected between 1884 and 1885 by Stavenov and Stinger, of Vienna. In 1927 work was done in the same region by Anton Raky, a well-known explorer who makes work of this kind his specialty.

Jan 1, 1941

By Homer Griffield Turner

The nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.&apos; Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties. Structure of Anthracite and Bituminous Coals A lump of bituminous coal (Fig. 1) is readily seen to be composed of layers differing from one another in texture, luster and thickness. There are, in general, three kinds of layers, although only two are usually seen. One is deep black, very compact, and has a bright luster; another is grayish black, has a duller luster and is less compact; the third is black, dull and porous in appearance, but because of its thinness is not often seen except on parting surfaces. This last material is charcoal. American students of coal morphology use the names anthraxylon, attritus, and fusain to designate these three constituents of laminated coal. Anthraxylon refers to the brightest bands, attritus to the duller layers, and fusain to the charcoal. Close examination of a lump of bituminous coal shows the brightest deep black layers to be embedded in the duller grayish black laminae. These deep black layers are lens-shaped and vary in thickness from thin sheets to over half an inch. They are often so continuous through the lump that their tapering terminae are not noticeable. On careful examination the duller grayish black laminae (Fig. 7) are seen to contain many very thin sheets of this very bright black material. The charcoal

Jan 1, 1930

By AIME AIME

WITHOUT frills, but with an admirable program of technical papers and discussion, many opportunities for social contact, and all New York for a playground, the 142d Meeting of the Institute will make the Engineering Societies Building a lively place from Feb. 20 to 23. Prices are down, even in New York. Come and forget the depression listening to the stories of old friends. Hear at first hand what is going on in your professional world. The fare is varied, of wide appeal. The program on the opposite page has been arranged carefully to minimize conflicts between the subjects in which you are interested. If it is not possible to come for all four days, check over the sessions that are most important to you. No changes in the scheduling are likely.

Jan 1, 1933

By C. R. Dale

IT IS the purpose of this paper to point out a number of the most common causes of crooked holes; to outline methods of drilling and straightening which to my personal knowledge have proved successful in numerous cases; to describe some of the characteristics of holes which, though not crooked in an exaggerated sense, may still cause serious mechanical trouble if not recognized and properly remedied; and to define clearly the part of oil-well surveying in the concerted effort operators generally are making to keep their wells straight from spudding to completion

Jan 1, 1931

The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as com- pared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams. Coal at Wales, in Sanpete county, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it "rock that would burn." In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the old Spanish Trail from Santa Fe. New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.

Jan 1, 1925

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.&apos; In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers&apos; loss because of break- age in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

At the request of representatives of the Treasury Department, President Winchell appointed the following committee, which .held a two-day conference with the Treasury representatives in Washington Oil Oct. 6 and 7 to aid in deciding upon the principles of mine taxation to he adopted by the Government. The results of this conference, which is not yet concluded, will be published in a future Bulletin.

Jan 11, 1919

By C. R. Sandberg, L. S. Gournay, R. F. Sippel

The effect of fluid-flow rate and fluid viscosity on oil-water relative permeability determinations was studied using the "dynamic flow technique." In this work relative per-nleability curves were obtained for homogeneous small core .samples from several sandstorle outcrop form-utions. Radio-tracers were used for the determination of fluid saturation and for the detection of saturation gradients. Cobalt-60 in the form of cobaltous chloride was used as a water-phase tracer in some of the experiments. Iodine-131 in the form of iodobenzene and Mercury-20-3 in the form of mercury diphenyl were used as oil-phase tracers in other experiments. Flow rates for each phase were varied within a range of 2.5 to 140.6 ml/hr. Oil-phase vis-cosities under flowing condition,> were varied from 0.398 to 1.683 cp. The relative permbilities ob-tained were found to he solely a function of saturation and independent of flow rare, provided there was no .Saturation gradient induced in the core sample by "boundary effect." Even though equilibrium with re-sped to flowing conditions was obtained at the lower flow rates, where a saturation gradient exists, this equilibrium is of a "contingent"-type rather than the "steady-state" equi-librium implicit in the relative per-meability concept. The only effect of increasing the oil or non-wetting phase viscosity was to decrease the flow rate required for the elimina-tion of the boundary effect. Fairly good agreement between experimentally determined and calculated values of the boundary effect was obtained when the non-wet-ring oil phase was the only Flowing phase. INTRODUCTION In the characterization of reservoir rock, as well as in the solution of reservoir production problems, it is most desirable to have reliablc rela-tive permeability measurements for the rock and fluids of interest. Many techniques have been developed for the laboratory determination of the relative permeability of both large and small core samples. In varying degree, difficulties attend the use of all of the methods. Each of the methods requires the metered flow of fluids of known viscosity through the core sample under conditions wherein the pressure drop in the individual flowing phases can be measured or closely approximated. Since the relative permeability is a function of the saturation and distribution of the flowing fluids, some means of obtaining such information is also required. The laboratory determination of the relative permeability of a sample should give the same relative permeability saturation relationship that would exist if the sample were in place in the oil reservoir. The attainment of this objective is complicated by the fact that the use of small core samples for laboratory measurements is usually necessary. As a result, errors in measuring the relative permeability arise from boundary effects at either the fluid input or output ends of the sample; no significant boundary effect is anticipated at the sides of the sample normal to direction of fluid flow. At the input end of the sample a boundary effect exists if the flow fluids are not com- mingled as they would be in the reservoir. At the output end of the sample a boundary effect exists as a result of discontinuity of the capillary properties of the system. Here the flowing fluids leave the small flow channels and enter a collecting system having much enlarged flow channels. Thus, there is a tendency for the wetting phase to be retained by the core sample because of the attraction of the core sample for the wetting fluid. No reference is made to these boundary effects in either Darcy&apos;s equation or in the relative permeability concept. As a consequence the saturation effect peculiar to the input end of the core sample may cause an error in the effective permeability measurement, since some portion of the core sample must be utilized for commingling of the flow fluids. At the output portion of the core sample a saturation gradient or a saturation change along the axis of flow results. Since relative permeability is a function of fluid saturation, this saturation gradient may cause a variable permeability measurement, especially since extent and character of the saturation gradient can vary with fluid-flow rate. The most convenient method of minimizing the boundary effect, especially at the output end of the sample, is to flow the fluids of interest through the core sample at such high rates that the capillary forces arc insignificant as compared to the viscous forces involved in the fluid flow. Since recent work of a preliminary nature has indicated that fluid dispersion in the porous medium increases with the flow rate, the high flow minimizes the boundary effect at the input end of the core sample by enhancing the mixing of the fluids.

Discussion of the paper of DORSET A. LYON and ROBERT M. KEENEY, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin. No. 92, August, 1914, pp. 1791 to 1800. LAWRENCE ADDICKS, Chrome, N. J.-I read this paper for the first time this afternoon, and it is really worthy of a much more careful reply than I can make with such a short time to consider it, but I just want to say that I differ with Dr. Lyon in his premises and conception of what happens in a refining furnace. He cites steel as an instance where the production of special grades justifies the high cost of power in an electric furnace, and goes on to say the same will be true in the case of copper, for the reason that you will get a better quality of product. I don&apos;t think you will get a higher grade of copper,. or a better conductivity, as I will explain in a moment. The cost of fuel in the Eastern plants is somewhere between 30c. and 40c. per ton of copper refined, and, if my memory serves me correctly, in an open-hearth steel furnace it is something like $1.25, so it is evident that steel could be handled to better advantage than copper on the basis of fuel. Now, taking the Great Falls plant to compare with is not quite fair, because that plant operates under peculiar conditions. The furnaces are relatively small; the coal is very bad and is very high in sulphur. No one would think of using a coal with 3.6 per cent. sulphur were anything better available. Due to these conditions, the amount of slag is inordinate, it being quoted as 3.5 per cent., and it is necessary to use lime, as there is a tendency to have troubles from arsenic owing to the very high current density used. I think he has taken about as hard a case as he could pick out. Now as to the conductivity of copper, my own idea about the reason that melted copper does not give as high a conductivity as pieces drawn directly from a cathode, or native copper, is that in the latter case the impurities are present as a mechanical mixture, while after melting they are chemically combined with the copper, which is a very different condition. Further, it is necessary to take the sample from a relatively smooth and consequently pure part of the cathode, as otherwise it would not draw. The same with the mass of copper; you pick out a good solid part of the copper, which is not representative. In fact, the refiners have all found they could not take fair samples of cathodes for a chemical analysis. It is always customary to use wire-bar copper -for the purpose of sampling, and the impurities are several times as great as shown by samples taken from .the cathodes. I think if we examine all of the examples he has given of cases where copper is higher in conductivity, it will fit with that explanation. For example, the Elmore process is a direct electrolytic deposit. Incidentally, at the present time there are a number of ex-

Jan 12, 1914