Search Documents

By H. J. Tschirner, L. P. Davidson, R. K. Carpenter

HE electrolytic zinc plant of the American Zinc Co. of Illinois, at Monsanto, was expanded in 1943 to a capacity of 100 tons of slab zinc daily. This capacity was not attained because of inability of the leaching plant to deliver an adequate amount of solution for electrolysis. Changing the leaching method so that the acid was added to the roasted zinc material reversed the usual procedure and made it possible to attain the desired capacity. The conditions which prevented satisfactory work before this change and the difficulties which arose in reversing the usual leaching procedure are described. The "reverse" leach operation as now practiced is carried out as follows: All the calcine to be leached is fed continuously to a slurry mixing tank. About one third of the acid to be used is fed to the tank with the calcine. The slurry is discharged continuously to a Dorr duplex classifier in closed circuit with a Hardinge mill. The classifier overflow is pumped to any of six leaching tanks where the leach is completed. A finished leach is discharged through Allen-Sherman-Hoff pumps to Dorr thickeners, from which the overflow goes to the zinc dust purification and the underflow to vacuum filters. This change in leaching procedure from the usual one of adding calcine to a large amount of acid made it possible to provide an adequate amount of purified solution to the electrolyzing division and at the same time filter and dry all the residue produced. Operating savings in reagents and better metallurgical recoveries were also important benefits. The original flowsheet of the leaching plant provided leaching, sedimentation of the insoluble residue, and purification of the neutral zinc sulphate solution with zinc dust. The thickened residue was filtered and washed. The purification cake of excess zinc dust, precipitated copper and cadmium, and any insoluble residue was filtered off on plate-and-frame duplex classifier. Settlement in the thickeners was inadequate and the suspended solids in the thickener overflow gave rise to filtration difficulties after the zinc dust purification. Further, the filtration and washing of the leach residue was poor, and it became necessary to pump a large amount of unwashed or poorly washed residue to storage ponds outside the plant building. Two causes of the poor settling and filtration were determined: Soluble silica and ferrous iron in the calcine treated. The latter was a result of poor roasting and with more experience ceased to be a major problem. The silica was a normal constituent of the feed and the working out of the problem became a matter of controlling its solubility. The obvious method to render the silica insoluble was by intensive roasting. This, however, met with total failure as such roasting resulted in silicates, probably zinc, soluble in the 13 pct acid used for leaching. Attempts were made to coagulate the fine gelatinous slime with addition agents. Glue, lime, starch, beef-blood serum and others were tried without success. All the suggested tried-and-tested means of operating the thickeners gave no consistently good results. Variations in leaching time, in addition of calcine to the leaching tanks, "conditioning" of the pulp by prolonged agitation, immediate discharge of the leach upon completion to avoid breaking up flocs were all tried and given up as ineffective. Byron Marquis, of Singmaster and Breyer, worked with the plant staff on a beaker scale until a leaching procedure was developed which gave consistent results and a promise of overcoming the difficulties which had plagued the plant operation. It was suggested that the difference in solubility of silicates and zinc oxide in sulphuric acid could be made use of in a leaching method where the acidity was controlled carefully. Such control is possible when acid is added to a slurry of calcine. This process reverses the normal procedure of adding calcine to a vessel of acid, hence the term "reverse leach" was applied. In this way, the overall acid concentration can be kept very low. In the tests made, it did not exceed 0.05 g per liter free sulphuric acid. Numerous advantages were realized when no silicates were taken into solution and later precipitated as a bulky gel. The gel had made reasonable thickening and filtration of the leach pulp and practical drying of the residue impossible. When the gel was eliminated, thickening rates were increased as much as five times. The volume of residue after thickening represented about 10 pct of the total leach pulp and had been as high as 95 pct when the gel was present. The thickened pulp was filterable and the filtered cake was dried readily after washing. The zinc extraction from the calcine was slightly lower. This was more than compensated for by the increase in zinc recovered in solution from zinc which had been trapped in the gelatinous residue. The amount of copper recovered was lower. However, the amounts of other impurities, such as arsenic, antimony, and germanium, taken into solution were lower. This was particularly true of antimony. Since the inception of reverse leaching, no concentrates have failed to yield solutions free of antimony even when present in the calcine to the extent of 0.2 to 0.3 pct. Oxidation of ferrous iron is a problem of reverse leaching. Ferrous hydrate does not precipitate at pH 5.3 to 5.4 where a leach is finished. The usual oxida-

Jan 1, 1952

By Frank W. Reinmiller, Edward S. Hsia

Earth bottom thickeners are generally considered to be the lowest cost solution for thickener bottom construction presently available to the mining industry. In addition to the capital cost advantage, these basins have proven to be watertight structures providing trouble-free operation for indefinite periods of time. During the past 15 years, some 18 of these thickeners have entered service with no particular problems encountered in porphyry copper operations, counter-current decantation in a gold cyanide plant, and other similar applications in mineral processing. In the course of this work, technological advances have been realized in the procedures for engineering and construction of these units to assure watertight basins and achieve all possible economies in construction.

Jan 8, 1977

By M. R. Moharam

The well-known formulae of screening efficiency and circulating load calculations in closed crushing circuits were exploited to achieve graphical estimation of these parameters. Three basic charts were proposed and constructed. The first one is for the regular closed circuits where the new feed goes to the crusher. The second is for the reverse closed circuits in which the new feed reported to the screen is free of screen undersize particles. The third chart controls the reverse circuits when they are receiving new incoming feeds containing undersize material. Compound circuits were also reanalyzed and a concept of equivalent simple circuit was introduced to enable graphical manipulation of these complex circuits with the help of the aforementioned charts

Jan 1, 1982

By K. Koneko, T. Nokoyama, S. Shibato

SEYBOLT et al.' have detected various silica films formed on a 3 pct Si-Fe alloy after heating at low oxygen potentials with the electron diffraction method, and they have made some observations on the H,0/H2 ratios required to form them. The purpose of this note is to describe the structure of the oxide film formed on either mechanically or electrolytically polished surfaces of a 3 pct Si-Fe alloy containing small amounts of manganese after heating at low oxygen potential. The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron, 76 pct ferrosilicon, and 76 pct ferromanganese, vacuum-in-

Jan 1, 1969

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

By C. C. Henning

In any line of human activity logical handling requires an amount of attention to each phase that is in keeping with the importance of that phase. In the complex and rapidly changing field of modern ferrous metallurgy it is difficult to allot the proper degree of attention to the various subjects, and it is not surprising that one or more subjects of major importance should for a time be neglected. Bessemer steel is a good example of a neglected subject. It is largely taken for granted, inferior physical quality is assumed for it, and there is a • lack of interest in its technical development and commercial application. Availability of supply is limited. In spite of this technical indifference, limited source and lack of commercial exploitation, bessemer steel constitutes a large volume of tonnage in daily use. There is a fairly prevalent idea even among technical people that bessemer steel survives mostly because of low cost and by reason of a dwindling residue of applications sufficiently common to permit of its use. The difference in cost between bessemer and open-hearth steel is governed largely by the relative cost of manufacture of pig iron and the market price of steel scrap. During the past four years there have been long periods of time during which the price of steel scrap was low enough so that open-hearth steel was considerably lower in manufacturing cost than bessemer. As to application, it may be pointed out that thousands of tons of this material in the form of bessemer screw steel are applied for moving parts in automotive and other equipment. Some forging work and considerable heat-treating, particularly carburizing, is performed on this grade. From an economic standpoint the most effective contribution of bessemer steel lies in its free machining qualities. It is by far the freest

Jan 1, 1935

Page Foreword—H. Foster Bain........................ 9 Letter of Transmittal—F. Julius Fohs...................11

Jan 1, 1927

By Reaves. M. J.

The title of my talk, "What Happened to the Uranium Boom?" is old news. Certainly it is for this group. All of us that make our living in uranium know that the boom of the last half of the 1970's is over. U.S. production has been exceeding consumption by more than two to one. Mines and mills are closing and yellowcake prices have been dropping for over 20 months. The gloomy outlook for the industry in the near term has been well documented by soothsayers of various descriptions, your daily newspapers, and in the Nuexco Monthly Reports. I'd like to attempt to describe the next upturn in the market (speculate, really) based upon the clues we're seeing now. In order to do that, I'd first like to go over briefly, some of the market factors that contributed to the recent price drop and resultant production cutbacks, and then hypothesize on the way these factors are changing and will change. Market prices are greatly affected (maybe even entirely determined) by buyer perceptions. This is particularly true with uranium, because of the long lead times associated with nuclear plant construction and also with conventional mine/mill development. Before the price rise (say, 1975) utility uranium buyers believed that: 1) U.S. producers would have difficulty expanding to meet U.S. demand. 2) Australian and Canadian production was essential to avoid shortages in the early 1980's. 3) Uranlum prices would continue to rise as demand exceeded supply. 4) Enrichment capacity would become inadequate. It was thought necessary, therefore, to build enriched inventory in the early 1980's for use in the late 1980's. Artificially accelerated expansion of the uranium producer industry was necessary to accommodate anticipated enrichment demand. Current perceptions are largely the opposite. These are the beliefs that were held most of this year and late last year as prices dropped. 1) U.S. production is far in excess of domestic need. Contraction of the U.S. production lndustry is necessary. 2) Canadian and Australian supply is optional and not essential. Producers in those countries are expanding mainly by displacing higher cost production and not because they fill a void, 3) Prices may be essentially stable for some time. 4) Enriched uranium is in excess supply. That is 1981. 1982 is shaping up to look like this: 1) Prices will have bottomed out. (That is not Nuexco's opinion necessarily, by the way, but it is my opinion.) 2) There will still be substantial utility inventories, but fewer spot sales. 3) Canadian and perhaps Australian sellers will have made substantial sales in the U.S. and will be aggressively seeking more. 4) U.S. production will have been dramatically curtailed. U.S. utilities that wish to con- tract long term will have difficulty in finding domestic sellers. Concern will develop about the availability of U.S. production capability. Virtually all long term con- tracts signed will be with non-U.S. sellers. 5) An awareness will begin to develop among U.S. buyers that we are approaching a period of dependence upon foreign uranium (which will be true). The history of the uranium market has been one of dramatic changes and overreaction to those changes. The rapid price rise of a few years ago generated excess U.S. production capacity and the rapid price drop of the last two years will almost certainly result in too little capacity. It will soon be difficult for U.S. buyers to buy domestic material except on the spot market. The question is, "will they care?" The lack of demand, of course, is the underlying reason for the current poor health of the uranium industry. In 1972, 1973 and 1974 collectively, there were 105 nuclear reactors ordered in the U.S. That ordering rate was expected to continue and accelerate throughout this century. In 1975, 1976, 1977, 1978, 1979, and 1980 altogether, there were 56 more reactors cancelled than ordered. The net growth of our only customer since 1974 has been a negative 56. TO put this in perspective, if these 56 reactors were operating now it would more than double present U.S. uranium consumption. Underlying lack of demand is something that is simply not going to change in this decade. Time is going to be required. The NRC indicates that the maximum feasible number of new reactors that can be licensed each year is six. That would increase uranium consumption by only 10% per year. New reactors, if ordered tomorrow, would not generate new uranium demand until after 1990. Even so, United States' consumption of uranium will rise from the 1980 level of 18 million pounds per year, to

Jan 1, 1982

NEW MEMBERS The following list comprises the names of those persons Who became members during the period July 10, 1918, to Aug. 10, 1918. ARCHER, EUGENE G., assayer and Chem., Granby Cons. Min. Smelt. & Power Co.,Anyox, B. C., Canada. BAKER, ROBERT C Mech. Engr. and Draftsman, Moctezuma Copper Co., Nacozari, Son., Mexico. BARNES, EDWARD A Supt., Fort Wayne Works, General Electric Co., Fort Wayne, Ind. BARNHART, EDWIN Engr. of Tests, Bethlehem Steel Co., Sparrow's Point, Md. BENSLEY, MAURICE D Pres. and Mgr., Frontier Brass Foundry, Inc., Niagara Falls, N. Y. BRADLEY, JOHN C Met., The American Brass Co., Waterbury, Conn. BRAGG, C. T Works Mgr., Michigan Smelt. & Refin. Co., Detroit, Mich. BRYMER, GEORGE W Min. Engr., 922 Union National Bank Bldg., Scranton, Pa. CHIVVIS, NORMAN Met. Engr., More-Jones Brass & Metal Co., 3144 North Broadway, St. Louis, Mo. CRAWFORD, R. D Prof. of Mineralogy & Petrology, Univ. of Colorado, Boulder, Colo.

Jan 9, 1918

By K. P. Mukherjee, K. P. Gupta, J. Bandyopadhyaya

Even though a lot of work has been done in the past to establish phase equilibrium in the Cu-Si system a re cent investigation casts some doubt about the existence and crystal structure of some of the phases that form in the composition range of 15 to 25 at. pct Si in Cu. The present investigation was carried out using high temperature X-ray diffraction technique along with other standard techniques to study the phases in this composition range. The high temperature 6 phase appears to be tetragonal with parameters a,, = 8.815A, c, = 7.903A, and co/ao = 0.896. The reported bcc E phase exists at room temperature and at least up to 780°C and appears to undergo a transformation near 600°C. The phase appears to be cubic but not of the bcc type. The ? phase appears to undergo a transformation, as has been indicated by earlier investigators, and the low temperature form of .? phase is tetragonal with parameters a, = 7.267A, co = 7.8924, and co/ao = 1.086. THE Cu-Si binary system has been investigated by several investigators1" and several intermediate phases,?,e,?' at lower temperatures and ?,ß,0,e, and ? at higher temperatures, were observed between terminal solid solutions of copper and silicon. Even though the existence of the e phase and the transformation in the ? phase were reported in many early works, in a recent study of this system Nowotny and Bittner6 doubted the existence of the e phase and phase at 550°C. Among the high temperature phases, the 6 phase was reported to have a complex cubic structure with parameter a, = 8.805A.7 Nowotny and Bittner, however, suggested that the structure of the 6 phase might be of CsCl type. In order to check these contradictory reports the present study was taken up to investigate the Cu-Si binary system in the composition range of 17 to 25 at. pct Si. EXPERIMENTAL PROCEDURE Weighed amounts of copper (99.99 pct) and silicon (99.9 pct) were induction melted in recrystallized alumina crucibles under argon gas atmosphere. The alloys containing 17, 18, 20, 21, 21.2, 22, and 24 at. pct Si were annealed in evacuated and sealed quartz capsules at 700°C for 3 days and subsequently water quenched. Other than this annealing, the 21.2 at. pct Si and 24 at. pct Si alloys were annealed at 550°C for 10 days, the 17 at. pct Si alloy was annealed at 750°C for 3 days, and the 22 and 24 at. pct Si alloys were annealed at 780°C for 2 days. All annealing temperatures were controlled to within *l°C. Alloys after quenching were subjected to metallographic and X-ray diffraction investigation. A solution containing 5 g FeC13 + 10 cc HCl + 120 cc H2O diluted with six times its volume with water was used as etching reagent. A 114.6 mm diam Debye Scherrer camera was used for obtaining diffraction patterns. The 17, 21.2, and 24 at. pct Si alloys were subjected to high temperature diffractometry using a Tempress Research High temperature attachment and a GEXRD VI diffractometer. For the 6 phase (17 at. pct Si alloy) powder specimen from a 750°C annealed alloy was reheated to 750°C in the high temperature attachment for 1½ hr before taking a diffraction trace. A 550°C annealed and slowly cooled phase (24 at. pct Si) alloy was first reheated to 550°C. a diffraction trace was made after annealing it for 2 hr, and subsequently it was heated to 716OC and kept at this temperature for 2 hr before taking a diffraction trace. For the e phase (21.2 at. pct Si alloy) a 550°C annealed and slowly cooled specimen was heated first to 425°C and annealed at this temperature for 2 hr before taking a diffraction trace. Subsequently, the specimen temperature was raised to 495", 540°, 603", 635", 682", 720°, and 748°C and homogenized at each temperature for 1 hr before taking diffraction traces. The powder specimen temperature was controlled to within +2oC at each temperature and argon gas, purified by passing it at slow rate through a fused CaC12 column, hot (800°C) copper and titanium chips and finally through a P2O5 column, was used to prevent oxidation of the powder. For all X-ray work copper-radiations at 25 kv, 15 ma (for Debye Scherrer technique), and 40 kv, 20 ma (for diffractometer tech-nique) were used. RESULTS AND DISCUSSION At 700°C the alloys containing 17 to 21 at. pct Si showed two phases while the 21.2 at. pct Si alloy was found to be single phase. The X-ray diffraction patterns of the two-phase alloys were consistent with the phase (ßP-Mn type structure) and the phase (21.2 at. pct Si) patterns. The diffraction patterns of the 17 at. pct Si alloy quenched from 750" and 700°C were identical. According to the accepted Cu-Si phase dia-gram4,5,10 the 17 at. pct Si alloy at 750°C should be in the (k + 6) two-phase region and very close to the -phase boundary. The identical patterns possibly resulted from the decomposition of the 6 phase on

Jan 1, 1970

By Douglas A. Anderson

We have instrumented well-controlled free-face blasts with six- component borehole strain gages, in order to determine the complete strain tensor as a function of time due to explosive loading. The strain tensors have been diagonalized to determine the principal strain time-histories, and further processed to determine the octahedral shear strains as a function of time. Principal strain time-histories, when compared with a computer model, indicate the arrival of various direct and reflected phases. Strong shear strains coincide with the expected arrival time of shear waves. These shear waves are probably instrumental in the fragmentation of confined rock due to explosive loading, and should be incorporated in models of the fragmentation process.

Jan 1, 1984

Page Foreword—H. Foster Bain........................ 9 Letter of Transmittal—F. Julius Fohs...................11

Jan 1, 1927

The Institute maintains for the use of members (and especially for the use of out-of-town members) a reading and writing room, where all usual office facilities are available, including telephone, telegraph, receipt, forwarding and care of mail and express packages, etc. A file of current magazines is also maintained in this room, and the Institute's staff will lend its best efforts to serving the members in connection therewith. The Institute also maintains for the use of its members free dressing rooms, library research department, etc. Attention is called to these facilities at the present time in the belief. that they may be especially useful to out-of-town members in connection with the Meeting.

Jan 5, 1918

By Raymond E. Funderburk

Today, there are four alternatives available for disposal of highly toxic, non-radioactive hazardous waste: deep well injection, chemical processing, landfill and incineration. However, based upon research conducted by the author, a fifth alternative now exists. Disposal in salt. Salt, because of its chemical characteristics, is an ideal medium for retention of inorganic hazardous waste. Except for a few elemental compounds such as lithium and potassium, there is no reaction with sodium chloride. In the family of inorganic wastes, there are basically seven suites of waste that may be mixed together without any chemical reaction. The process developed by the author would be to take a suite of waste, either dewater or add moisture, add a solidification agent to the mix and slurry pipeline the mass into a cavern. Residence time before hardening can be adjusted, but the nominal time until full solidification is 48 hours. Once solidified, the mass will reach compressive strengths exceeding 3000 psi. The slurry can be introduced into an evacuated cavern pumped free of brine, or it can be placed beneath the brine and the waste will force the brine to the surface. The latter technique requires a high degree of engineering control to prevent contamination of the brine leaving the cavern-thus creating more hazardous waste and additional problems. The Environmental Protection Agency endorses the concept both at the research level and within EPA Headquarters. The technology will soon be utilized in a salt formation in Texas.

Jan 1, 1985

By Charles W. Goodale

The attention of the Institute has been called by Prof. John A. Church* and Mr. W. Lawrence Austin? to the free-milling ores of the Tombstone mines and their treatment, but the silver-bearing man ganese ores of the district have received only a passing notice. As these ores show some interesting peculiarities, and have yielded not less than 750,000 ounces of silver, they are worthy of some study. The Knoxville, Lucky Cuss, Luck Sure, and Wedge mines (named in the order of their importance) are situated along the northern border of the district. They have been the leading producers of this manganese ore, and possess the same general characteristics. Special attention will be given to the Knoxville, as it has been the one most extensively developed. The limestone belt, in which the Knoxville ore bodies occur, has an easterly and westerly trend, is about 1680 feet wide, and rests on granite on the north, the plane of contact being nearly vertical. It is overlain by quartzite, the contact-plane having a dip of 82°. Some mining has been done along these contacts, and a considerable amount of pay ore has been extracted, but development has been very superficial. The ore found along these contact planes contains very little manganese, and differs entirely from the ore in the lime stones. No attempt will he made to assign this limestone country-rock to a particular geological horizon, as no fossils have been found in it. Prof. Blake, in a paper on "The Geology and Veins of Tombstone, Arizona" (Trans., x., 334), speaks of the middle and upper strati-

Jan 1, 1889

By H. M. Chance

Recent research work has shown that coal can be produced, at reasonable cost, from almost all coal-mining districts containing not more than 3 to 8 per cent. of ash. From coal so produced, an abundant supply of coke, suitable for blast-furnace operation, can be made containing from 12 down to 6 per cent. or less of ash. These statements apply broadly to the Appalachian coal belt, including most of the mining districts in Pennsylvania, Ohio, West Virginia, Kentucky, Tennessee, and Alabama. The exceptions will generally be found among those coals carrying a prohibitive percentage of sulfur. Any gravimetric heavy fluid method of separation will effect a reduction in the percentage of sulfur, but this reduction may not be sufficient to produce, from coal unfit for metallurgic use, a product that can be so used. When a large part of the sulfur is in the form known as "organic sulfur, "or is present as very finely disseminated and homogeneously distributed pyrite, possibly it cannot be eliminated from the low-ash coal produced. When the sulfur exists as pyrite in distinct layers, bands, or nodules, or when it is finely disseminated but is irregularly distributed, often a low-ash coal low enough in sulfur to make good metallurgic coke can be produced from relatively impure coals. It has generally been assumed that the quality of coke on which blast furnaces must be operated depends on the geographic location of the furnace, and that the grade of coke on which a blast furnace must operate is that produced from the best coal obtainable by careful mining; or if the coal is prepared by washing, hand picking, or other means by which the foreign impurities are removed, that the grade of coke on which the furnace must operate depends on what has been termed the "inherent ash" of the particular coal. The term "inherent ash " is generally understood to mean the percentage of ash present after all removable (free) impurities, slate, fireclay, high-ash bony coal, and pyrite have been removed, and is usually applied to the percentage of ash present in run-of-mine coal from any mine after these impurities have been removed. Perfect washing, or perfect preparation, is understood to be attained when the percentage of ash in the washed coal is reduced to the percentage of inherent ash; that is, of ash that cannot be removed by the washing processes in common use. Wash-

Jan 1, 1924

PAGE Problems of American Railroads Early in 1936, by J. J. Pelley 3 The Heavier Nonferrous Metals in Transportation, by C. H. Mathewson... 9 Light-weight Metals in the Transportation Industry, by Zay Jeffries 21 Trends in the Metallurgy of Low-alloy, High-yield-strength Structural Steels, by H. W. Gillett 40 Structural Steels and Light-weight Metals in the Transportation Industry, by Horace C. Knerr 62 Proposed Use of Alloys in Merchant Shipbuilding, by Edgar P. Trask 66 Mutual Effects of Metallurgy and Speed in the Automotive Industry, by Merrill C. Horine 84 The Railroads and Light-weight Equipment, by W. W. Colpitts 93

Jan 1, 1936

Dr. George Ferdinand Becker, a prominent geologist, connected with the United States Geological Survey since 1879, died at his home in Washington, D. C., Apr. 21, at the age of seventy-two.

Jan 5, 1919

By Robert B. McCormick

World War II has developed a use for the nonmetal mineral quartz crystal that was unknown in World War I. During the interim period of peace, experimental work in the radio field with the piezoelectric properties of quartz crystal resulted in the almost universal adoption of quartz-crystal radio oscillator plates to control frequency in radio broadcasting, police, commercial and amateur communications equipment. Telephone resonators and filters made from quartz crystal also were developed, which vastly improved the frequency control of long distance telephone circuits. Expansion of the Industry The sudden war demands of the armed services for radio equipment using quartz crystal for frequency control led to an unprecedented expansion of the manufacturing industry. It is estimated that the 1940 peacetime volume amounted to approximately $1,500,000, while today a vast new quartz-crystal industry supplies more than $150,000,000 worth of quartz oscillator plates to the Army and Navy each year. This demand has caused an enormous expansion not only of American manufacturing facilities but also of Brazilian mining output, virtually our only source of raw quartz crystal. Actual figures of imports and consumption cannot be cited, for security reasons, but certain comparisons have been made, which indicate the transformation of quartz crystal from a minor to a major nonmetal. Lundl has shown that the value of quartz-crystal exports from Brazil is now about equal to that of phosphate rock produced domestically in 1941 and actually exceeds the combined value of crude feldspar, gypsum and fluorspar production in the United States in the same year. This great expansion under wartime pressure was not accomplished without some anxious moments, but all the demands of industry have been met and the Government has been able also to accumulate a substantial stock pile of material against future contingencies. Inspection and Grading of Quartz Crystal The swift growth of the quartz-oscillator industry necessitated the simultaneous evolution of methods and criteria for inspecting and grading quartz crystal. It has been found that, generally speaking, it is economically feasible to cut only crystals that are at least 30 per cent by volume free from major defects such as optical and electrical twinning, cracks and fractures. Blue needles, bubbles, "chuva" and other minor imperfections can be tolerated in the usable portion unless present in great excess. The present marketing system in use in both Brazil and the United States, as far as quality is concerned, depends solely on the "usability" of a crystal, which is defined in the Brazilian-American agreement2

Jan 1, 1948

By Robert B. McCormick

World War II has developed a use for the nonmetal mineral quartz crystal that was unknown in World War I. During the interim period of peace, experimental work in the radio field with the piezoelectric properties of quartz crystal resulted in the almost universal adoption of quartz-crystal radio oscillator plates to control frequency in radio broadcasting, police, commercial and amateur communications equipment. Telephone resonators and filters made from quartz crystal also were developed, which vastly improved the frequency control of long distance telephone circuits. Expansion of the Industry The sudden war demands of the armed services for radio equipment using quartz crystal for frequency control led to an unprecedented expansion of the manufacturing industry. It is estimated that the 1940 peacetime volume amounted to approximately $1,500,000, while today a vast new quartz-crystal industry supplies more than $150,000,000 worth of quartz oscillator plates to the Army and Navy each year. This demand has caused an enormous expansion not only of American manufacturing facilities but also of Brazilian mining output, virtually our only source of raw quartz crystal. Actual figures of imports and consumption cannot be cited, for security reasons, but certain comparisons have been made, which indicate the transformation of quartz crystal from a minor to a major nonmetal. Lundl has shown that the value of quartz-crystal exports from Brazil is now about equal to that of phosphate rock produced domestically in 1941 and actually exceeds the combined value of crude feldspar, gypsum and fluorspar production in the United States in the same year. This great expansion under wartime pressure was not accomplished without some anxious moments, but all the demands of industry have been met and the Government has been able also to accumulate a substantial stock pile of material against future contingencies. Inspection and Grading of Quartz Crystal The swift growth of the quartz-oscillator industry necessitated the simultaneous evolution of methods and criteria for inspecting and grading quartz crystal. It has been found that, generally speaking, it is economically feasible to cut only crystals that are at least 30 per cent by volume free from major defects such as optical and electrical twinning, cracks and fractures. Blue needles, bubbles, "chuva" and other minor imperfections can be tolerated in the usable portion unless present in great excess. The present marketing system in use in both Brazil and the United States, as far as quality is concerned, depends solely on the "usability" of a crystal, which is defined in the Brazilian-American agreement2

Jan 1, 1948