Search Documents

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By J. T. Norton, Pekka Rautala

The phases and equilibria in the W-Co-C system have been studied by X-ray diffraction methods, metallographic technique, and thermal analysis. In addition to the 7 phase, two double carbides, called 8 and have been revealed. The compositions correspond to CO3 W6C2 and Co3-W10C4. The reactions leading to these phases have been explained and tentative diagrams of stable and metastable equilibria proposed. The basic reactions in sintering cobalt cemented tungsten carbides are discussed. THE W-Co-C system is of fundamental importance in practical carbide manufacturing as well as for the understanding of the sintering mechanism. Surprisingly little is known about this system, for the probable reason that all the important alloys are of two-phase structure and that the diagram Co-WC has been treated as a quasi-binary. This obviously is incorrect, because WC decomposes before melting. One ternary phase, 7, of composition Co3W3C has long been known. It was first studied by Adelskold, Sundelin, and Westgren,1 although the isomorphous iron-tungsten carbide was known earlier. There have been in the literature several reports of two 7 phases.' " Also the 7 phase has been considered unstable by Takeda4 and Westgren.1 The Co-WC diagram has been studied by Wyman and Kelley5 and a quasi-binary diagram has been published by Sandford and Trent.2 Takeda has published a tentative Co-W-C diagram, considering both metastable and stable equilibria. However, the lines of two-fold saturation are shown only partially and it seems impossible to complete the diagram without violating the phase theory. Therefore it seemed desirable to examine the system in more detail. Experimental Procedure The alloys used in the present investigation were made of powders of tungsten, tungsten monocarbide, cobalt, and carbon and were of the grade used in manufacture of commercial cemented carbides. The powders were ground and mixed in small stainless steel ball mills, using balls of the same material. Benzene was used as a dispersing agent. The mixing period was 1 hr, since this was shown to give suffi- ciently good mixing of the powders without too great a contamination from the mill. After ball milling, the specimens were pressed in cylindrical or rectangular dies. No paraffin or other lubricant was used and the small compacts had sufficient green strength to be handled without difficulty. Several sintering furnaces were employed. The most satisfactory arrangement was a vacuum furnace based on the Arsem principle which employed a graphite helix as the resistance heating element. Specimens were placed on graphite stands and there was generally a slight carburization or decarburiza-tion of the specimen surface, depending on the carbon content of the alloy. The evaporation of the cobalt at a sintering temperature of 1400°C was not significant, but became severe at 1500°C and higher. The sintering time was 1 hr at 2000°C and 2 to 4 hr at lower temperatures. It was not possible to quench the specimens, but the cooling rates were rather fast, greater than 300°C in the first minute. In the system under investigation, the reactions are sluggish, and it is believed that the high temperature structures are satisfactorily retained. The principal method of investigating the sintered specimens was X-ray diffraction by the Norelco recording spectrometer. Approximate determinations of the phase boundaries were made by the disappearing phase method. Ternary Phases To study the phase formation in W-Co-C system, a series of specimens was sintered at 1400°C. In this experiment two ternary phases, called here ? and k were formed in addition to the well-known 7 phase. The 7 phase, which has been completely described by Westgren: showed a range of homogeneity from 7 to 20 pct C and from 38 to 48 pct Co. At 1400°C the 7 phase was found to be in equilibrium with monotungsten carbide, 8, tungsten, 8, #?, and liquid. The boundaries toward #? and liquid were difficult to determine and appeared to be very temperature sensitive. The other boundaries are believed to be well fixed. The homogeneity range of 7, as measured in this work, is considerably smaller than the one

Jan 1, 1953

By G. Bruggeman, K. G. Kreider

Grain boundary dij]usion coefficienls were measured in tungsten between 1400° and 2200° C and can be expressed by the equation sq cm per sec This activation energy confirms some eavlier estimates made .from tungsten sintering experiments. Grain boundary diffusion was found to occur in sub-bozrndavies having -misorientations of less than 10 deg. The actiuation energy for this subboundavy diffusion is equal to that for dijjusion in incoherent grain boundaries with in the limits of error. This is shown to be consistent with the dislocation model of Low-angle boundaries wheve diffusion occlcvs along- the dislocation 'YPipes" comprising -tile boundary. RECENT investigations of the sintering of tungsten powders all report activation energies which are considerably less than the activation energy for tungsten volume diffusion. Kothari' reports a value of 100 * 5 kcal per mole, Hayden and Brophy' obtained 90 kcal per mole, and Vasilos and smith3 found 110.7 kcal per mole from their sintering studies. Since most determinations of the activation energy for volume diffu-sion4-' fall between 120 and 160 kcal per mole (the true value seems most likely to be nearer 150 kcal per mole), the conclusion is drawn that the mass transport leading to densification during sintering is accomplished by grain boundary diffusion. This interpretation is consistent with various diffusion models of the sintering process. 10-12 Vasilos and Smith calculate diffusion coefficients from their data which fit the equation D * 1.36 x 10* exp(-llO,700/HD However, no direct measurements of tungsten grain boundary diffusion have been made. Furthermore, considerable disagreement exists between the directly measured values of tungsten volume diffusion.'-' In order to corroborate the inferred results of the sintering experiments concerning grain boundary diffusion and to provide accurate diffusion data essential to the analysis of the kinetics of creep, oxidation, precipitation, and so forth, the present work was undertaken to measure self-diffusion in single-crystal and polycrystalline tungsten between 1400" and 2200°C. It is within this temperature range that tungsten sintering is done, the re crystallization of tungsten occurs, and the widest application of tungsten as a high-temperature material will probably be made. EXPERIMENTAL PROCEDURE Radioactive WlE5 was produced by irradiating tungstic acid in a neutron flux of 1.2 x 1012 neutrons per sq cm per sec for 36 hr. A 2-week waiting period was allowed for the decay of w"~ also produced by the irradiation. (w"~ has a half-life of 24 hr.) The half-life of the remaining isotope was determined to be 75 days confirming the presence of w lE5 and the absence of any undesired radionuclide. Specimens 4 in. in diam and $ in. thick were cut from polycrystalline swaged tungsten rods (recrystal-lized) and from Linde single-crystal rods. Chemical analyses of these materials appear in Table I. Actually upon closer examination, the single-crystal specimens were found to consist of several subgrains separated primarily by tilt boundaries in which the misor-ientation ranged from 3 to 10 deg. Thus, it was possible to measure boundary diffusion coefficients in these low-angle subboundaries as well as in the incoherent boundaries of the polycrystalline specimens. The two faces of each specimen were ground flat and parallel within 0.0001 in. The radioactive tungstic acid was dissolved in concentrated ammonium hydroxide, placed on the ground flat of the specimen, and evaporated to dryness. The oxide was then reduced in hydrogen at 1000°C resulting in a layer of wlE5 approximately 1 p thick. The diffusion anneals were performed in vacuum in a tantalum resistance furnace. Time at temperature ranged from 10 hr at 1400°C to 2 hr at 2200°C. The penetration profile was determined by measuring the residual activity after successive removal of surface layers by grinding on metallographic polishing paper. Extreme care was exercised to insure that sections were always taken normal to the diffusion direction; this was verified repeatedly by checking that front and back surfaces of the specimen remained parallel. The activity was measured with an end-window Geiger-Mueller counter. The sides and edges of the specimen were well-shielded to eliminate possible effects due to surface diffusion. The weight of the

Jan 1, 1968

By Donald F. Kennedy

During the past several years Climax Molybdenum Co. has been engaged in testing various types and sizes of hollow drill steel. The majority of tests have been on 7/8-in. hexagon st.ee1, inasmuch as it represents approximately 70% of total drill steel consumption at the Climax operation. Prior to December 1960, tests on 7/8-in. hexagon drill steel were conducted on steel with a forged collar and, in most cases, with a threaded bit connection. Through these tests and research, some improvement in steel life was achieved by making changes in heat treatment, design and alloying constituents. However, during that month, research and testing commenced on a rubber collar which was designed to replace the forged collar on 7/8-in. hexagon drill steel. Manufactured by the LeRoi Div. of Westinghouse Air Brake Co.. the collar. is very simple in design, consisting of a 1 ½ -in. diam steel cylindrical sleeve 2 in. long, containing a bonded rubber insert and attached to the steel with an epoxy cement

Jan 8, 1962

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10 to Nov. 10, 1915: Members BECK, WESLEY HUDSON, Civ. and Min. Engr., Ellsworth Collieries Co., Ellsworth, Pa. BRADSHAW, GRANT D., Pres., Andrews-Bradshaw Co, 409 Diamond Bank Bldg., Pittsburgh, Pa. BUTLER, BERT S., Geol U. S. Geological Survey, Washington, D. C. CAMERON, FRANK, Asst. Mine Foreman, Braden Copper Co., Rancagua, Chile, So. Amer. CHEN, YEFAH FRANCIS, Asst. Min. Engr., Pinghsiang Colliery, Pinghsiang-Ki, via Changsha, China. CLAGHORN, DAVID MONTGOMERY, Mining Engr., Timekeeper, Wilkeson Coal & Coke Co., Wilkeson, Wash. DAVIS, REUBEN WALDO, Min. Engr., Supt., Cannel Coal Co., Dolores, Webb Co., Tex. DOUTHETT, GEORGE M., Supt Crescent Metals Co., Glenwillard, Pa. DUNSFORD, ENSOR R., Min. Engr., Asst. Supt., Victoria Gypsum Min. & Mfg. Co., Ltd., Quarry, St. Alms. C. B.. Nova Scotia. Canada.

Jan 12, 1915

By Robert D. Gunn, John E. Boysen, Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyo., was completed on Jul. 30, 1976. During the experiment production reached 0.32 blm3/d (12 M cu ft/d) of 6.9 w/m3 gas (175 Btu per cu ft). Approximately 6100 tonnes (6700 tons) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, coal gas thermal efficiencies of 76 to 89%, and overall process efficiencies of 65 to 74% were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-74.

Jan 1, 1978

[University of Alaska College, Alaska Mining Society TOM CHRISTENSON, President MARY ANN KISER, Secretary H. G. WILCOX, Faculty Sponsor WM. FACKLER, Counselor University of California Berkeley, California Mining Association JOHN W. COOK, President LORETTA A. RICHTER, Secretary W. S. WEEKS, Faculty Sponsor]

Jan 1, 1946

(This list includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. The last complete list was printed in Bulletin No. 131, November, 1917. A complete Honor List is maintained in the reception room at the office of the Institute:) AARONS, J. BOYD, Captain, 4th Reinforcements, 11th Infantry, Australian Imperial Force. AHBE, F. R., Captain, 33d Engineers. AMBLER, HARRY A., 30th Infantry, Camp Greene, Charlotte, N. C. ALFORD, NEWELL G., Sergeant, Headquarters 84th, 9th Division, Camp Zachary Taylor, Ky. ANDERSON, ALEXANDER, Lieutenant, Royal Garrison Artillery. ANDREWS, CLARENCE W., 1st Infantry Co., Officers' Training Camp, 83d Div., Camp Sherman.

Jan 2, 1918

All the Affiliated Student Societies report that the present college year promises to be a most successful one. The officers for this year, so far as reported, are as follows: TUFTS COLLEGE CHEMICAL SOCIETY President, CHESTER B. PIERCE Vice-president, JOHN H. SCHMUCK Secretary-treasurer, DANIEL A. PRESCOTT President, R. G. SATTERLEY Third vice-president, H. E. BLAKE First vice-president, LESTER VOCKE Secretary,-J. E. FLANIGAN Second vice-president, `V. J. KLINE Treasurer, PROF. JAMES FISHER, JR About 75 per cent. of the students are ex-service men, and most of them saw service in France.

Jan 12, 1919

Committee. ROBERT H. RICHARDS, Chairman. ALBERT SAUVEURr Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE. HENRY A. WENTWORTH. The thirteenth meeting of the Boston Local Section was held at the Engineers' Club, 2 Commonwealth Avenue, Boston, on Monday evening, Oct. 6, 1913. Fourteen members and three guests were present at the dinner, at which Chairman Robert H. Richards presided. After the dinner, the Chairman expressed his pleasure in welcoming the members at the first dinner following the vacation. He said that lie had attended a meeting of the Directors of the parent society in New York ; that they had asked what the Boston Section were doing, and expressed their hope that we would be able to make some of our papers formal and offer them for publication. The Chairman then said that lie realized the objection to this; that members were less willing to speak for publication than informally, but that lie hoped, nevertheless, that some of the speakers this year would see their way to write up a formal paper at some later date, along the general lines of their informal ,addresses.

Jan 11, 1913

As is known to representatives on Engineering Council, the Patents Committee of Council has collaborated with the similar committee of National Research Council in developing a scheme for the improvement of the method of dealing with patents in this country. The staff of the Patent Office is itself actively engaged in this effort. Out of the report prepared by the National Research Council, and approved and adopted by Engineering Council as the report also of its Patents Committee, remedial legislation has taken form. Three hills have been introduced, known as H.R. 5011, a bill to make the Patent Office independent of the Department of the Interior or any other department, and to simplify the procedure of the Courts with reference to assessment of damages or profits for infringement of patents; H.R. 5012, a bill to establish a single Court of Patent Appeals; and H.R. 7010, a bill to increase the force and salaries in the Patent Office. Chairman Charles A. Terry, of the Patents Committee, requests that representatives of Engineering Council write to their congressmen, urging the passage of these hills and so far as convenient, request their friends to do likewise.

Jan 9, 1919

By S. A. LoPilato, J. T. Smith

SEVERAL techniques have been evaluated for cooling the throat area of rocket-nozzle inserts to prevent erosion or fracture of the inserts during exposure to high operating temperatures and pressures. Self-cooled composites, such as infiltrated tungsten, have shown considerable promise for these applications. These composites can be fabricated by infiltrating the refractory matrix with a lower-melting metal or non-metal which is insoluable in tungsten. During firing, the lower-melting substance undergoes a series of continuous endothermic phase changes which absorb sufficient heat to maintain the nozzle matrix material at or below a safe operating temperature. At present, the state-of-the-art has reached a point where the refractory matrix density and microstruc-ture have been established as the critical parameters to be controlled for optimum self-cooled performance.'" Nondestructive testing has been utilized to ensure that porous tungsten billets were of uniform density and free from cracks or other defects prior to fabrication into rocket nozzle inserts. Ultrasonic-velocity techniques have been employed because of their reliability and reproducibility. The purpose of this note is to present and interpret the test data developed for porous tungsten matrices. For evaluation purposes, tungsten powders with Fisher subsieve sizes of approximately 4 and 18 p have been obtained for study from four commercial sources: the General Electric Co., Wah Chang Corp., Fansteel Metallurgical Corp., and Kennametal, Inc. Porous tungsten matrices were fabricated from the powders by hot pressing in induction-heated graphite die assemblies. Typical billets ranged from 3 in. diam, 2 in, high to 5 in. diam, 5 in. high. The ultrasonic-velocity measurement technique employed was through transmission, pulse echo at a frequency of 1.0 mc using matched barium titanate crystal transducers. The testing equipment included a pulsed ultrasonic generator, an amplifier, a specimen holder, and an oscilloscope, as shown in Fig. 1. The porous tungsten thickness was measured to i 0.0005 in, with precision micrometers while the oscilloscope achieved 0.02 psec time measurement accuracy. The time for a sound wave to pass through the billet, the bulk wave velocity, was calculated to 0.5 pct using Eq. [l]: V-} where V = bulk wave velocity, in. per psec, T = specimen thickness, in., and / = time, psec. To develop inspection standards, the bulk density of a porous tungsten billet was determined by the ASTM water-immersion technique.3 The ultrasonic-velocity measurements were completed at seventeen positions for each billet and averaged to develop a characteristic standard velocity for a particular tungsten powder at several density levels. A plot of ultrasonic velocity vs density is presented in Fig. 2 for six different tungsten powders. This graph has been established as

Jan 1, 1967

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By David L. Holt, Walter A. Backofen, Anwar-uI Karim

Specimens of a hydrided Mg-0.5 Zr alloy were strained in tension at 500°C and constant rates of 2 x10-3 5 x 10-3, and 2 X 10" min-1. Hydride-denuded zones formed at grain boundaries normal to the tensile-stress direction as a result of magnesium transport during difusional flow. The width of the zones could be measured and the measurement used for calculating the diffusional component of the imposed tensile strain. The strain from diffusional flow was found to increase with imposed strain at a diminishing rate, tending to saturate at approximately 12 pct. Strain rate sensitivity of flow stress was low. The apparent non Newtonian character of the diffusional flow is attributed to a non Newtonian process acting in parallel with it which could be boundary shear. Fracture grows out of voids that form in the denuded zones. DEFORMATION of a grain by diffusion of atoms from boundaries stressed in compression to boundaries stressed in tension is Newtonian viscous,1-3 and evidence has accumulated in recent years that such a process may be responsible for the high strain-rate sensitivity of the flow stress of super-plastic alloys.4"7 One piece of evidence is that experimental stress: strain-rate relationships can be quantitatively explained.5-7 There is also metallo-graphic evidence of diffusional flow in superplas-ticity, but in a limited amount. The formation of striated bands on the surface of superplastically deformed specimens has been attributed to diffusional flow.5"7 The basis of that attribution came from experiments on a coarse-grained, nonsuperplastic and hydrided Mg-½ wt pct Zr alloy which formed hydride-denuded, light etching zones at tension-stressed boundaries when strained in tension at 270?C.6 The origin of these zones had already been traced to the diffusional flow of magnesium atoms to the boundaries.' The particular observations in the more recent work were of striated-band formation on the surface and denuded-zone formation internally, with both the bands and zones having the same width and appearing at tension-stressed boundaries. It was argued that the bands were a surface manifestation of the zones and hence of diffusional flow. Of course in superplastic alloys which do not contain internal metallographic "markers", the surface bands can be the only metallographic indication. In the present work, denuded-zone formation was utilized, as it has been by others,9-11 to extend the observations of diffusional flow and to measure the strain, ed, resulting from it. Grain size had to be large to measure ed with accuracy. The grain size chosen for this study was -30 , and with that a strain of 10 pct from diffusional flow produces a denuded zone only 3 µ in width. The large grain size naturally precludes superplasticity. The observations of diffusional flow were complemented by determining the strain from the other operative deformation modes: slip, e,, and grain boundary shear, egb. An incremental specimen extension is the sum of increments from slip, and grain boundary shear as well as diffusional flow. Division by a common length is required to convert to strain. If this length is taken as the initial specimen length, then imposed engineering strain, e, is given in terms of the component engineering strains by e = ed + es + egb [1] Stress:strain-rate relationships are determined by the way in which this "strain balance" is made up. EXPERIMENTAL Material. Zirconium hydride markers were introduced into the Mg-0.5Zr alloy by annealing in hydrogen at 450°C for 30 min. The hydride concentration was particularly high at zirconium rich stringers, which was fortunate in that the transverse boundaries at which denuded zones form lie perpendicular to the stringers. Grain size after annealing was 30 µ. Photomicrographs of unstrained and strained material are shown in Fig. 1. Procedure. Specimens were strained in tension with an Instron machine at crosshead velocities of either 2 x 10"3, 5 x X or 1 x 10-2 in. min-'. Specimen length and diameter were 1.0 and 0.2 in., respectively, so that initial strain rates in tests at constant crosshead speed were 2 x 10"3, 5 x X and 1 X l0-2 min-1. Tests were made at 500°C which is a compromise temperature at which diffusional flow is still measurable but grain growth is not active enough to interfere with metallographic measurements. The tests were made in a hydrogen atmosphere. Strain Balance. An equation additional to [I] is eg = ed + es [2] where eg is strain measured from grain elongation. Measurement was made of ed, eg, and, of course, e, which enabled all the strains in Eq. [I] to be determined. For this purpose, strained specimens were sectioned longitudinally, polished, and etched. The strain from diffusional flow, ed, was computed by measuring on photomicrographs the width in the tensile direction of denuded zones at either end of a grain XI, X2, adding them, and dividing by twice the initial longitudinal grain dimension L0, Fig. 2. Reported values are the results of measurements on seventy randomly selected grains; 95 pct confidence limits on ed were +1.5 pct strain. To measure eg, the maximum length, L, and the maximum width, W,

Jan 1, 1970

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

MONTANA LOCAL SECTION Executive Committee F. M. SMITH, Chairman J. L. BRUCE, Vice-Chairman . D. C. BARD, Secretary, Box 267, Butte, Mont. FREDERICK LAIST W. C. SIDERFIN The semi-annual meeting of the Montana Section was held at the Silver Bow Block, Butte, Mont., on Friday evening, Oct. 8, 1915. An informal, subscription dinner, at $1.50 a plate, was enjoyed inn' the early evening, by 62 members and guests. After dinner a technical session was held, and a paper entitled Preliminary Outline of Paper on Mines in the Boulder Batholith was presented by J. A. Grimes, who is joint author of the paper, with Paul Billingsley. The paper elicited a lively and interesting discussion, in which a score of members took part. After the reading of the paper the rest of the evening was spent socially. D. C. BARD, Secretary.

Jan 12, 1915

By J. K. Edgar

FOR a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the recrystallization of the heavily cold worked metal at room temperature.' Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would be of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth1 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 655°C'. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutectic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653° PREPARATION AND CHEMICAL ANALYSIS OF ALLOYS Electrolytically refined aluminum (99.991 pct aluminum) and a high purity aluminum-iron alloy (11.45 pct iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The analyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1948

By K. M. Fagin, D. W. Carter

Six new oil fields were discovered in the East and East Central Texas district during 1942. The Coke and Quitman fields, in Wood County, at this time appear to be the two most important oil discoveries for the year. The. four other oil fields discovered were Concord, in Anderson County; Kildare, in Cass County; Weiland (ClubLake), in Hunt County; and Larissa, in Cherokee County. The Rodessa lime in the Chapel Hill field, Smith County, provided the only new oil zone in older fields. The Hawkins field, Wood County, was the most active in drilling operations, 125 new wells being completed during the year. The Chapel Hill field tied the Coke field for second place with 30 completions each. The third most active field was Kildare, with 10 completions. Like the other oil-producing districts of the country, wartime restrictions reduced the number of oil and gas-well completions to 265 in 1942, compared with 964 completions in 1941. This represents a drop of 72 per cent and only a little more than one half enough to replace the 437 producing wells abandoned in the district during the year. Tn addition, the number of producing wells temporarily shut down nearly tripled, far two principal reasons: (I) the rule of the Petroleum Administration for War preventing operators from equipping more than, one well on each 10 surface acres with pumping or artificial-lift equipment, and (2) the Railroad Commission's issuance of various orders permitting the transfer of allowable for wells having high water-oil ratios and high gas-oil ratios to other wells capable of producing the same with less waste of reservoir energy. No changes were made in prices of crude oil in the district during 1942. Production and Probation The district produced 158,928,281 bbl. of oil and distillate during 1942, compared with 163,566,695 bbl. during 1941, which represents a decrease of 3 per cent. The East Texas field produced 120,680,595 bbl. of oil, compared with 130,377,793 during 1941; a reduction of 9,697,198 bbl., or 7.4 per cent. The production of this field represents 75.9 per cent of the district total, compared with the 79.7 per cent that it furnished in 1941. The district had an estimated basic daily oil allowable of 623,242 bbl. on Dec. 31, 1942. Approximately 31.8 per cent of the production in Texas during 1942 was supplied by this district, compared with 33 per cent during 1941- Changes in the annual production of newer and flush fields in this district are attributable either to a difference in the number of wells producing during the year or to changes in basic allowable and number of shutdown days due to shifting market dconditions brought on by the war. All regularly prorated fields in the district were shut down 123 days. Major exceptions were the East Texas field, closed128 days; Hawkiis, shut down 106 days; and Cayuga, Sulphur Bluff, Talco, and Rodessa, which

Jan 1, 1943

By D. W. Carter, K. M. Fagin

Six new oil fields were discovered in the East and East Central Texas district during 1942. The Coke and Quitman fields, in Wood County, at this time appear to be the two most important oil discoveries for the year. The. four other oil fields discovered were Concord, in Anderson County; Kildare, in Cass County; Weiland (ClubLake), in Hunt County; and Larissa, in Cherokee County. The Rodessa lime in the Chapel Hill field, Smith County, provided the only new oil zone in older fields. The Hawkins field, Wood County, was the most active in drilling operations, 125 new wells being completed during the year. The Chapel Hill field tied the Coke field for second place with 30 completions each. The third most active field was Kildare, with 10 completions. Like the other oil-producing districts of the country, wartime restrictions reduced the number of oil and gas-well completions to 265 in 1942, compared with 964 completions in 1941. This represents a drop of 72 per cent and only a little more than one half enough to replace the 437 producing wells abandoned in the district during the year. Tn addition, the number of producing wells temporarily shut down nearly tripled, far two principal reasons: (I) the rule of the Petroleum Administration for War preventing operators from equipping more than, one well on each 10 surface acres with pumping or artificial-lift equipment, and (2) the Railroad Commission's issuance of various orders permitting the transfer of allowable for wells having high water-oil ratios and high gas-oil ratios to other wells capable of producing the same with less waste of reservoir energy. No changes were made in prices of crude oil in the district during 1942. Production and Probation The district produced 158,928,281 bbl. of oil and distillate during 1942, compared with 163,566,695 bbl. during 1941, which represents a decrease of 3 per cent. The East Texas field produced 120,680,595 bbl. of oil, compared with 130,377,793 during 1941; a reduction of 9,697,198 bbl., or 7.4 per cent. The production of this field represents 75.9 per cent of the district total, compared with the 79.7 per cent that it furnished in 1941. The district had an estimated basic daily oil allowable of 623,242 bbl. on Dec. 31, 1942. Approximately 31.8 per cent of the production in Texas during 1942 was supplied by this district, compared with 33 per cent during 1941- Changes in the annual production of newer and flush fields in this district are attributable either to a difference in the number of wells producing during the year or to changes in basic allowable and number of shutdown days due to shifting market dconditions brought on by the war. All regularly prorated fields in the district were shut down 123 days. Major exceptions were the East Texas field, closed128 days; Hawkiis, shut down 106 days; and Cayuga, Sulphur Bluff, Talco, and Rodessa, which

Jan 1, 1943

By J. T. Norton, J. G. McMullin

An 1820°C isothermal cross section of the Ti-Ta-C ternary diagram was prepared from X-ray diffraction and metallographic data. No phases other than those appearing in the three binary diagrams were observed. At temperatures above the titanium transition temperature titanium and tantalum form a complete series of solid solutions containing up to 2 atomic pct C. The phases Tic and TaC also form a continuous series of solid solutions extending across the diagram. PREVIOUS work on this alloy system was very limited. Of the three binary constitution diagrams involved, only one, the Ta-C system was available in the literature. Preliminary data on the other two systems was received from the investigators during the course of the investigation and both have been published in recent months. It had been shown that Tic and TaC formed a continuous series of solid solutions, but the range of carbon content in this phase was not known. While Ta2C had been described, its solubility for or reactions with other carbides had not been reported. It was not known whether or not any ternary compounds occurred in the system. The present program was undertaken to determine experimentally the general form of the ternary diagram. It is hoped that the results will be of value in furthering the development of sintered carbide cutting materials and high temperature ceramets, many of which contain combinations of Tic and TaC. The Binary Systems Of the three binary diagrams involved only that of Ta-C was available at the time this project was started. The diagram of Ellinger¹ redrawn in Fig. 1, shows a hexagonal phase Ta2C having a very small composition range and a cubic TaC phase having a composition range of from 40 to 50 atomic pct C. The authors made a separate determination of the composition range of TaC using lattice constant values and found the range to extend from 40 to 49.7 atomic pct C in good agreement with Ellinger's diagram. Two determinations of the Ti-Ta system have appeared recently.2,3 These two diagrams are in good agreement and show that ß titanium and tantalum form a complete series of solid solutions. The Ti-C diagram by Cadoff and Nielsen4 shows a very limited solubility of carbon in both a and ß titanium. The single carbide formed persists over a wide range of carbon contents. Several values for the upper limit of carbon content of this phase have been reported."' The highest value obtained in the M.I.T. Laboratory was 47.5 atomic pct C with a lattice constant of 4.328?.5 Fattinger7 describes a gas carburization method which he claims produces stoichiometric Tic although he does not present any data showing that he actually had 50 atomic pct combined carbon. Several complete analyses on

Jan 1, 1954