Search Documents

By W. F. Carew, F. A. Crossley

Tensile, creep-rupture, and stability tests were employed to evaluate the effect of a-strengthening and ß-complexing additions on the base composition Ti-6Al-3Mo. The ultimate objective was to produce an alloy of greater strength than the Ti-7A1-3Mo alloy. Strengthening of a was accomplished by additions of 2 and 4 pct Ge, 4 pct Sn, 4 pct Zr, and 2 pct Sn-2 pct Zr. Making the ß more complex while keeping the total of ß-stabilizing additions constant at 3 pct resulted in higher tensile strengths but lower creep and rwpture strengths, especially at 1000°F. None of the more complex versions of the base alloy offers greater promise than the Ti-7A1-3Mo alloy. However, some improvement in the strength of the latter may follow from additions of zirconium perhaps up to 4 pct. PREVIOUS work directed at the development of titanium-base alloys with: 1) minimum room-temperature tensile elongation of 10 pct in 1 in., 2) high creep resistance at elevated temperature, and 3) the ability to retain original room temperature tensile ductility following exposure to creep conditions at elevated temperatures, demonstrated Ti-Al-Mo ternary compositions in the range 5 to 7 pct Al-3 to 6 pct Mo to be the most promising. Of this group the Ti-7Al-3Mo alloy was the strongest.'-= The objective of the present work was to determine if alloys of this type could be further strengthened by making additions which dissolve preferentially in the a-phase and by making the ß-phase more complex. For this study the base composition Ti-6Al-3Mo was selected rather than Ti-7Al-3Mo in order to minimize the possibility that in a more complex alloy with a-strengthening additions, low ductility might obscure the strength contribution. The metals

Jan 1, 1959

By Leendert de Witte

Conventional resistivity logs consisting of a short normal, a long normal, and one or more long lateral curves do not give data that allow a complete quantitative interpretation in beds thinner than 20 ft. Reservoir rocks usually exhibit zones of continuous homogeneity of quite limited thickness where the long lateral curves become useless because of adjacent bed effects and boundary phenomena. If the beds are 12 ft or thicker, the short and long normals may be used for qualitative interpretation, which can be streamlined by the application of simplified departure curves. For beds of a thickness less than twice the long normal spacing, this procedure breaks down. The combination of the limestone curve, the later-olog or guard electrode log, and the microlaterolog permit quantitative interpretation for beds that are at least 10 ft thick, provided the mud resistivity and the hole diameter are known with sufficient accuracy. For beds thinner than 10 ft, combinations of the microlaterolog with short spaced laterologs and pseudo laterologs appear to be promising. Interpretation of these curves again requires the application of simplified departure curves. Resolution of various possible combinations was analyzed using departure curve data calculated on the Whirlwind I computer at the Massachusetts Institute of Technology. A field example is shown using the microlaterolog-microlog combination, and the combination of a 6-in. modified laterolog plus a 6-in. pseudo laterolog. INTRODUCTION For the purpose of quantitative interpretation of resistivity logs in porous formations, we want to obtain two essential quantities from the logs, namely, the true resistivity of the undisturbed formation, Rt, and the resistivity of the part of the formation invaded by mud filtrate, Rt. The apparent resistivities of all conventional logging devices are functions of these two parameters and are also influenced by a third unknown parameter, the diameter of the invaded zone, d. It has been shown' that from the normal curves alone it is impossible to arrive at a unique solution for the three unknowns, Rt, R1, and d1. In very thick homogeneous beds, if invasion is not too deep, we can obtain a fair approximation to Rt from the long lateral curves and then use the two normal curves to find Rt and d1 Even under the most favorable conditions, the resolution of this system is not very good. The short normal does not give a reasonable approximation to R1 unless invasion is very deep (dl>16 hole diameters). For very deep invasion, however, the long laterals no longer approximate Rt. For bed thickness between 20 and 40 ft, the long laterals are affected appreciably by the adjacent beds; and the curves are distorted by boundary anomalies to the extent that they lose their quantitative usefulness in most cases. For the same bed thicknesses, the normal curves still function reasonably well. Although it is impossible to find unique solutions Lor R1 and Rt using the normal curves alone, we can obtain a reasonable approximation for the ratio R1/Rt through the use of simplified departure curves. This fact was brought to our attention by A. J. de Witte, geologist with Continental Oil Co. As the magnitude of Rl/Rt is a major clue to the presence of oil in formations, this method can be used to good advantage for qualitative analysis and will be discussed in somewhat greater detail. With the aid of suitable bed thickness corrections, the analysis of the normal curves may be used for bed thicknesses larger than 12 ft. For thinner beds, the method rapidly loses its resolution; and we have to resort to different types of resistivity logs if we want to attempt to analyze the curves quantitatively. The inadequacy of conventional resistivity curves in thin beds is far more serious than generally realized. Fig. 1 shows a conventional E. S. with a 16-in. and 64-in. normal and a 16-ft lateral through a section of Lansing-Kansas City lime, in comparison to a guard electrode survey through the same section in a neighboring well. The porous zones, which show up as low resistivity breaks on the guard electrode log, are completely masked by adjacent bed effects and boundary anomalies on the conventional curves. Even the short normal shows most of the porous Zones only as Vague deflections and in many cases fails to register Their

Jan 1, 1955

By E. Parthe, J. P. Pemsler

TWO references can be found in the literature concerning the ternary system uranium-tantalum -carbon. C. H. Schramm, P. Gordon, and A. R. Kaufmam reported in this Journal1 on the existence of the ternary carbide "UTa10C4." They also report a second face-centered-cubic carbide phase in the system U-Ta-C, which they denote as "white" phase. The publication includes a reproduction of a Debye-Scherrer powder photograph of "UTa10C4" and a list of the sin2 0 values of this compound. H. Nowotny, R. Kieffer, F. Benesovsky, and E. Laube2 report the complete solid solubility between TaC and UC with a B1 structure. Since the ternary phase "UTa10C4" lies very close to the binary system Ta-C, and the established phase Ta2C with a C27 structure had not been mentioned by Schramm et al., it was thought worthwhile to compare the patterns of "UTa10C4" with Ta2C. The strong lines of the given pattern were indexed on a hexagonal unit cell with the approximate cell parameters a = 3.09A and c = 4.93A. These are the values reported for Ta2C in the literature.3 The correspondence between reported and calculated sin2 8 values may be studied in columns 4 and 5 of Table I. The agreement is fair, but there remain weak lines which cannot be assigned to the hexagonal unit cell. The extinctions correspond to those of Ta2C, but a comparison of the calculated and observed intensities of the Ta2C lines (columns 2 and 3) with those of the corresponding lines of "UTa10C4" (column 6) show occasional deviations. To clarify this situation, four new samples were prepared. The compositions of these samples were chosen in such a way as to observe any existing ternary phase in the system TaC-UC-U-Ta. The samples were arc melted in an inert atmosphere and annealed at 1100°C for 36 to 72 hr. Compositions of the samples determined by chemical analysis are given along with the results of X-ray investigations in Table 11. The following conclusions may be drawn from these data: a) No ternary compounds occur in the section TaC-UC-U-Ta of the ternary system Ta-U-C. The "white" phase reported by Schramm et al. corresponds to a solid solution between TaC and UC. Only one three-phase field exists: C27-B1-A2. (Both tantalum and ? uranium have body-centered-cubic A2 structures.) The a uranium observed in sample 4 transformed from the high-temperature ? phase on cooling. b) The phase Ta2C with a C27 structure extends into the ternary system. "UTa10C4" is, therefore, a uranium-enriched Ta2C. Good agreement is ob-

Jan 1, 1960

By Joseph L. Gillson

IT is a somewhat curious circumstance that the newest of the Institute's several awards should be conferred in the oldest of our several professional fields—for there is little question that geology and mining have antedated metallurgy and petroleum. Perhaps so did geophysics. After all, one geophysical instrument, the magnetic compass, has been successfully employed for many centuries. Young in years the Jackling Award may be, but in distinction—whether in terms of the title it bears or in terms of the first three medalists (Reno Sales, E. D. Gardner, and the late Father MaceIwane)—the Jackling Award is already one of the ranking awards of the Institute. The name of the 1957 medalist will bring added luster to an already illustrious roll. J. L. Gillson was born and brought up in Evan-ston, Ill., in an area characterized by singularly flat and uninspiring topography, and devoid of ore deposits and even of bedrock—a most unlikely environment from which to expect a future Jackling medalist to emerge! On graduating from high school he enrolled as a chemistry major at Northwestern University. At the end of his frkshman year his scholastic prowess had won him a prize of two chemistry books. But these went unread, for about this time he came under the spell of U. S. Grant, that distinguished and enthusiastic geologist who for many years was head of Northwestern's geology department. From thence forward Joe was a dedicated geologist. After a Navy interlude in World War I, he went to MIT for graduate work, substituted for the late Professor Palache for one year at Harvard in mineralogy, received his doctorate at MIT and stayed on as a meniber of the MIT faculty, where the geology department was headed by that great dean of all economic geologists, Waldemar Lindgren. In 1926 Joe spent a summer looking into barite deposits for the du Pont Co., and since 1928 he has been du Pont's chief geologist. Do men who lead such active lives in our exploration organizations generally have permission to publish their observations? Do they generally find time to publish, even if they have permission? Alas, no. But in Joe Gillson's case, yes. His bibliography runs to well over two score papers, including one of the very first papers in this country on the applications of petrography to problems of Portland cement. He has written on such topics as the origin of talc and the genesis of ilmenite, fluorspar, and alkaline rocks. Each year for a number of years his annual reviews of industrial minerals in the Mining Congress Journal have been eagerly awaited. - Do men who do so much to advance their science have anything left to give to the advancement of their profession? In Joe Gillson's case, yes. He has been a vice president of the Mineralogical Society of America and has been active in the councils of the Society of Economic Geology, particularly in their research programs. This year he is president of the American Geological Institute, currently perhaps the most challenging post to which a geologist may be elected. His contributions to AIME scarcely need documentation, so I shall mention only three—his chairmanship of the Committee on Democratization of the Institute, a committee whose work and recommendations brought a new and hopeful leaven to AIME at a time when this was sorely needed; his chairmanship, a few years ago, of the Industrial Minerals Division; and his current place on the Board of Directors as Vice President of the Institute. Such' a catalogue of contributions and achievement, even as condensed as I have had to make it, certainly merits the Jackling Award. Yet, implicit although not often expressed in the conferring of most awards is the hope that besides recognizing a distinguished career, it will provide stimulus for further effort. In the present instance, such an expectation is already well on the way to fulfillment. Only recently Joe Gillson has undertaken the editorship of a new and greatly revised edition of the Institute's Seeley Mudd volume, Industrial Minerals and Rocks. And so, Mr. Chairman, it is with pleasure and enthusiasm that I present Dr. J. L. Gillson for the 1957 Jackling Award.

Jan 1, 1958

By K. A. Natarajan, I. Iwasaki

The meaning and the utility of redox potential (Eh) measurements in sulfide flotation systems are examined. Since some preliminary plant Eh and laboratory flotation data were available, experiments were made to establish the pH range at which a platinum electrode might be used for such measurements without much difficulty in aerated systems. Triangular wave voltammetry was used to study the surface conditions of the electrode immersed in pyrrhotite suspensions at different pH. The measured Eh both at the plant and the laboratory is interpreted in terms of the experimental water-oxygen line.

Jan 1, 1974

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By Martti E. Maliniemi

The Svappavaara mine is located 47 km southeast of Kiruna C. The ore deposit now being worked, Leveäniemi, belongs to Luossavaara- Kiirunavaara AB (LKAB) and is the company's, and also Sweden's, third biggest mine after Kiirunavaara and Malmberget. The distance by rail to the Norwegian port of Narvik is 214 km and to Lulei on the Gulf of Bothnia 340 km (Fig. 1). The village of Svappavaara has about 800 inhabitants. The climate is arctic in character. The temperature during the months of December to February is about -20º to -35ºC, and the ground is covered by a blanket of snow for about eight months of the year. The brief, intensive summer often arrives with startling speed, bringing both sunshine and warmth. HISTORICAL BACKGROUND Mining operations took place in Svappavaara as far back as 300 years ago. During the period 1655-1684, copper ore was taken from the deposit called Gruvberget in the vicinity of the village. The total production of raw copper was probably about 1,045 tons. During the 18th and 19th centuries, several attempts were made to extract iron ore from the numerous deposits found within the district. These brave attempts, however, were foiled by the high phosphorus contents and the enormous transport difficulties. The present-day mine fields in Leveäniemi were discovered in 1897. At that time, it was difficult to determine the size and value of the deposit because of the thickness of the soil cover (3 to 15 m) and the

Jan 1, 1969

By B. B. Cox

Iraq, formerly called Mesopotamia in Asiatic Turkey, became a kingdom under British Mandate after the world war and is expected to gain its independence in 1932 when it enters the League of Nations. The kingdom is shown on Fig. 1 in its relations to neighboring countries, to the Mediterranean Sea and to the Persian Gulf. It is slightly smaller than the State of Texas with its capitol, Baghdad, inland about as far from the Persian Gulf as Breckinridge, Tex., is from the Houston Shipping Channel. The oil fields lie 180 to 225 miles north of Baghdad, or about as far as from Breckinridge to Oklahoma City, and about as far from the Mediterranean as Fort Worth is from Hobbs, N. M. A narrow-gage railway runs from Basra, the Persian Gulf port, to Baghdad. From there another narrow-gage runs into the Kurdish hills east of the Tigris to Kirkuk. A standard-gage, part of the old Berlin-Baghdad system, follows the west bank of the Tigris northward from Baghdad to Baiji, a village about 100 miles south of Mosul. No railway exists between Iraq and the Mediterranean, though the Anatolian Railways in southern Turkey come to within 50 miles of the Iraq frontier and 120 miles of Mosul. Surveys have been completed for a railway through British Mandates from Haifa to Baghdad as well as for a railway through French Mandated Syria from Tripoli to Abu Kemal near the Iraq border. Wagon roads, excepting those constructed by the oil companies, are few and indifferent in Iraq and no road exists across the desert to the Mediterranean, but contrary to prevalent beliefs the surface is firm and free from sand dunes so that motor cars can go almost anywhere in dry weather, with ease. Frequent motor car and airplane service exists between Baghdad and the Mediterranean ports and motor car service may be had between Kirkuk and Nisibin, Turkey, where on two days each week through Wagons Lits service is available to Paris. Baghdad is about 21 days distant from New York City with present transport facilities. The climate is semiarid, similar to Imperial Valley, California, the average rainfall outside the mountainous parts amounting generally to

Jan 1, 1932

By P. Dayal, L. S. Darken

THE migration of carbon in austenite under the influence of an electric current has been observed qualitatively several times.14 Lebedev and Guterman5 recently have reported quantitative measurements; their method consisted of welding a low-carbon to a high-carbon wire, passing current, and later estimating the carbon distribution metal-lographically. We believe the method reported in this paper is superior in principle since electrolytic migration and ordinary diffusion are not necessarily coupled as in the weld method; also for the first time the extent of migration is determined by combustion analysis for carbon. A uniform tubular specimen (S.A.E. 1045 or 1095) was mounted as illustrated in the figures. the whole assembly being in an atmosphere of purified nitrogen. Direct current (129 to 226 amp at 0.65 to 1.0 v) served as source both of heat and of potential gradient for carbon migration. The duration of experiment was 7.5 to 12 hr, during which time the temperature was controlled (±10°C) manually. The experimental conditions are indicated in the first five columns of table I. With this experimental arrangement, the temperature initially has a maximum value at the central plane. Also, in this vicinity (by virtue of the symmetry), the carbon entering any volume element is equal in quantity to that leaving; the loss or accumulation of carbon occurs near the electrodes since the carbon moves uniformly near the center and is "frozen" at the cold ends. Hence, providing the time of experiment is not sufficiently long to seriously influence the conditions at the central plane, carbon crosses this plane only under the influence of the electrical potential gradient and not under the influence of temperature or concentration gradient. The amount of carbon which has crossed this plane was determined by combustion analysis of the two halves of the specimen. The results of these analyses are shown in the sixth and seventh columns of table I. It will be noted that substantial amounts of carbon migrated from the anode portion to the cathode portion (except at 920°C, which temperature was too low to exhibit the effect in the allotted time). In spite of precau-tions taken, considerable decarburization occurred as may be seen by comparing cols. 8 and 5. In three cases (indicated by asterisks in table I) the specimen was ground on one side, polished, and examined metallographically before analysis. One specimen was normalized and re-examined. Micrographs of selected areas in specimens 4 and 6 are shown in figs. 1 and 2, respectively. Evidence of carbon migration from the anode toward the cathode is quite apparent. Fig. 2 shows abundant graphite as well as cementite in a region near the cathode. The temperature of this zone is estimated at about 800°C. In fig. 1, particularly in the micrograph on the extreme right (the right side of which is of unaltered carbon content), there is evidence of slight depletion of carbon in the immediate vicinity of the cathode as contrasted to the general increase in carbon of the cathode half of the specimen. Although this may be attributed in part to decarbur-ization, it is believed that it is occasioned also by thermal diffusion—migration (of carbon) from a cool to a hot zone4—a phenomenon superimposed upon the electrical migration. Evidence of carbon migration was visible particu-larly during the course of the high-temperature,

Jan 1, 1951

By David B. Reger

Oil and gas and their derivatives continue to be stable products in West Virginia. In the midst of the cataclysmic happenings of 1930 to 1934, which have swept away banks and practically destroyed many other enterprises of presumably nonspeculative character, the possession of a royalty or working interest in a few old oil or gas wells has prevented disaster in literally thousands of homes. These old wells yield their daily quotas of basic commodities, which the public must have. Fortunately, the facilities of disposal in the Appalachian Province are so ample and well managed that the owner of such equities may be reasonably certain that his proportionate share of existing markets will be afforded him without much effort on his part. In most cases these investments are free from encumbrance or hypothecation, therefore the main uncertainty is the date of ultimate exhaustion at the source. Generally, this is known to be fairly remote. The net result has been that individual owners part with such investments only as a last resort. In sharp contrast to the action of the small owner of wells or royalties who has prudently refrained from jeopardizing his rather certain income by drilling new wells that may be failures, or of which the product may not be needed for the moment, has been the plight of various promotional enterprises in natural gas. Many of these ventures have been operated by amateurish remote control and practically all have been overloaded from the start with bonds and debentures, which could only be satisfied in a rising and expanding market; and with operating costs that have been exceedingly high because of widely scattered producing units and large overheads. Many of these promotions are now in receivership or bankruptcy and in various instances the original units have been recaptured by former owners and have again become profitable by reason of personal operation and elimination of all forms of overhead expense. New Development In 1934, the State issued 524 permits for drilling. According to the trade journals, 553 wells were completed, with 184 oil wells, 274 gas wells and 95 dry holes (Table 3).

Jan 1, 1935

By Charles R. Cavanaugh, John F. Elliott

The activity of nickel in liquid Pb-iVi alloys which are rich in lead was measured in the temperature region of 700° to 1100°C by means of the galvanic cell: The electrolyte used was stabilized zirconia. Tlze data were correlated using the a function, and a plot of the temperature coefficient aE/aT All subsequent calculations of the thermodynamic properties are based on these two functions. The activity, activity coefficient, and molar properties of mixing of nickel are reported. Nicke1 shows extreme positive deviations frorn ideality while lead shows a very slight positive deviation in the composition range studied The study of the activity of nickel in liquid Pb-Ni alloys reported herein was undertaken to explore the use of stabilized zirconia, an oxygen-ion electrolyte, with liquid-metal electrodes, and to obtain further information on the thermodynamic properties of the liquid binary Pb-Ni system. The cell The reversible electromotive force of the cell results from the difference in the chemical potential of the oxygen at the two electrodes: po, (left) - p~ (right) = -4E5 [I] The chemical potential of oxygen on the right is fixed by the activity of nickel in the solution and pure solid nickel oxide. That on the left is set by pure solid nickel in equilibrium with pure solid NiO. By definition: Since the chemical potential of nickel is related to the chemical potential of oxygen through the equilibrium constant for the formation of NiO from nickel and oxygen gas, the electromotive force of the cell is also expressed In this case, n is 2, E is the reversible potential of the cell, and 5 is Faraday's constant. The work of Kuikkola and wagnerl and Schmalz-reid2 has shown that the stabilized zirconia electrolyte is essentially an ionic conductor at the oxygen levels encountered in the experimental arrangement of the work, i .e., PG > 10-l7 atm. THE EXPERIMENTS The advantage of this type of reversible cell over those using a liquid electrolyte is the simplicity arising because the electrolyte also functions as one of the containing crucibles. A further simplification was the choice of the Ni (sat.)-NiO electrode as the standard. This permitted a ready check on the behavior of the electrolyte, as the potential of the cell must become zero when the right electrode becomes saturated with nickel, either because of a change of temperature or because of the addition of nickel to the electrode. It also permitted the potentials being measured to lie in the most satisfactory experimental range of 0 to 100 mv. Although it was not theoretically necessary, lead was included in the standard electrode as it assured good contact between the electrode and electrolyte. Cell Design. The general arrangement of the experimental cell assembly is shown in Fig. l(a) and the details of the cell itself are contained in Fig. l(b). The anode lead wire on the interior of the cell was connected to a coil of perforated sheet nickel. Within this coil were nickel oxide pellets which were held beneath the surface of the liquid Pb-Ni alloy. A disc of nickel oxide was held at the bottom of the external crucible (alumina) by means of the thermocouple protection tube. The nickel oxide disc and pellets were compressed dry at 10,000 psi and sintered at approximately 1000°C for an hour in air. A major experimental difficulty of reversible electromotive force cells with liquid electrodes is the selection of suitable materials for connecting

Jan 1, 1964

By Geo. H. Ashley

The following paper is intended to be suggestive only, and to open the way for discussion and further observation. Its preparation was requested only two days before the time limit set for the submission of the papers comprising this symposium. Thus no time existed for detailed studies, so it is largely a memorandum of such facts as have come incidentally to the notice of the writer in the study of coal in the field. The field study of sulfur in coal has received very little special attention or description from coal student's. The presence of sulfur concretions is noted in hundreds of descriptions, and certain benches of a coal bed may be described as "sulfury" or the presence and position of sulfur bands may be noted in coal sections in connection with sampling. It may be accepted that some sulfur is present in all coal. The amount varies greatly in different regions, in different beds, and in the same bed in different areas. The anthracite of Rhode Island comes the nearest of any coal known to the writer of being free from sulfur, several analyses of that coal showing less than 0.1 per cent. Subbitumi-nous coals in Colorado in a few places have close to 0.2 per cent. of sulfur on the dry-coal basis and in other states subbituminous coals approach this lower limit. Bituminous coals seldom run under 0.4 per cent. of sulfur on the dry basis, though in a few places dry bituminous coals in Colorado and Washington have between 0.3 and 0.4 per cent. The better known bituminous coals have almost everywhere over 0.4 per cent. The best of the Pocahontas and New River coals run close to 0.4 per cent., but there is very little commercial coal in Pennsylvania, Ohio, Indiana, Illinois, Kentucky, or the other states, that runs under 0.5 per cent. on the dry basis. From these minimum figures, the amount will range up to 5 or 6 per cent. or higher if visible sulfur is not excluded. It must be remembered that the usual analysis of a coal bed is not intended to give the total proportion of sulfur in the bed but the amount in the coal after the removal of the more obvious and larger sulfur masses. Professor Parr has already pointed out that, chemically, sulfur occurs in several forms: as pyrite, organic sulfur, sulfates, and possibly as un-combined sulfur. Sulfur in the form of sulfates is commonly the obvious result of the weathering of pyrite and may be found in the coal within .

Jan 1, 1920

By R. C. Rumble

To /neet the need for a subsurface flowmeter capable of measuring low rates of flow, a new type flowmeter has been built and tested in the field. This instrument is self-contairzed, can be run on a wire measuritzg line, and may be run through 2-in tubing. It consists of a rotameter flow-measuring assembly used in conjuncfion with a conventional subsurface instrument clock and chart. Integral with the tool is an inflatable packer which, by effecting a seal between casing and tool, diverts all fluid through the metering assembly. Packers of different size adapt the tool to different sizes of casing or liner. The flowmeter is capable of measuring rates of flow as low as 4 BID. The flowmeter has been run experimentally in seven wells. It has yielded satisfactory resrrlts in five of the wells, and in the other two it failed to operate because of loose sand in the hole. INTRODUCTION One of the oldest problems facing the producing branch of the petroleum industry is the location of depths of entry of fluid into a wellbore and the determination of the amount of fluid entering at each depth. This problem is often encountered in oil and gas wells completed in single producing horizons as well as in multiple pays; it is a common problem in oil wells which produce excessive volumes of gas. Several subsurface instruments designed to detect and meter flow in the producing interval of wells have been described in the literature.1,2,3,4 Most of these, however, were apparently intended for use in wells producing at relatively high rates of flow, and consequently lack sensitivity to low flow rates. Because of this and of other possible disadvantages inherent in these instruments, development of the subsurface flowmeter described in this report was undertaken. DESIGN OF FLOWME'I'ER Design Requirements In considering the requirements for a flowmeter that would not be subject to the limitations of devices existing at the time work was started, attention was first given to the size of the tool. Such an instrument should be of sufficiently small diameter that it could be lowered readily in 2-in tubing in a producing well. The flowmeter should contain a recording unit so that it might be run on a wire measuring line with conventional reeling equipment. It should not be too long to be accommodated by a portable lubricator of the type used for running conventional subsurface instruments. The metering mechanism of the flowmeter should not be affected appreciably by the viscosity or density of the flowing fluid. Such an instrument should record flow rates in the range from less than 10 B/D to over 100 B/D. To achieve this, a packer should he provided to divert through the instrument all fluid flow in the wellbore. This packer should be of such nature that in the event of excessive flow the fluid would bypass the instrument instead of forcing it up the wellhore. General Description A flowmeter incorporating most of the desired features outlined above was developed and built. The instrument is an elongated tubular device terminated on

Jan 1, 1956

By B. F. Oliver, F. Garofalo

Gas-metal heterogeneous reactions and zone-lrelting were sinultarneously employed to produce several high-purity irons with low interstitial contents in a levitating- zone melter. Successive zone-tneltitzg pusses were made in carious sequences of atmospheves which included prepuvified tank hy-drogeta, water vapor hydrogen, palladiuril-purified hydrogen, and vacuunm of 2 x 10-6 Torr. Different irons ranging in purity from 99.89 to 99.996 pct with residual curbon contents of 17, 8 to 10, and 3 to 5 ppm have been Drepared. No measuvable gradient in the residual carbon content was observed along the entire zone-melted length (6-10 in.) in I-ilz.-diameter bars. The absence of a carbon-concentration gradient in the solid indicates an apparent distvihution coefficient of 1, an unusual condition. Internal friction, solid-state extraction, and hot-hardness results indicate that the level of mobile carbon in a iron depends on the gas-metal heterogeneous reactions employed. Purification under an oxidizing atmosphere resulted in the immobilization of nearly all of the carbon present at leuels of 10 ppm or less. Continuation of purification in a reducing atmosphere veturued the carbon to a state of mobility which was aguin reversed by further purification in all oxidizing atmosphere. The immobilization of curbon at "vesidual levels " is believed to be associated with a strong interaction between carbon and oxygen atoms. frons with low carbon and nitrogen contetzts which did not exhibit a hot-hardness peak were produced after zone ynelting in vacuum. CARBON, nitrogen, and oxygen have strong and well-known effects on many properties of iron. These effects persist even at concentrations of 5 to 20 ppm. The intent of the present investigation was to establish procedures for the preparation of high-purity iron with concentrations of these elements in the range of 5 to 20 ppm and lower. The results reported here deal with the procedures employed to prepare high-purity iron, and with observations on the behavior of certain elements at "residual levels": particularly carbon. The details of the (levitating) zone melter in which the final purification steps are performed and the necessary control of the pertinent solidification variables have been described previously.1,2 MATERIALS AND PROCEDURES Commercial electrolytic iron was induction vacuum-melted and cast into 30-lb ingots. Melt additions and ingot analyses for carbon, oxygen, and nitrogen are noted in Table I. All ingots were melted in stabilized zirconia crucibles conditioned with one iron wash heat. Middle sections of the ingots were forged to 1-1/4-in. rounds, machined to 1-in.-diameter bars, then cut to 36-in. lengths. The zone-melting operations were performed on six iron bars (A to F) at a freezing velocity of 2 in. per hr with the freezing interface rotating2 at 200, 300, or 400 rpm. Liquid zones were passed through the bars in various sequences of atmospheres, Table 11, including prepurified tank H2, palladium-purified Hz, wet H2, and system vacuum of 2 x 1018 Torr. Wet-Hz atmospheres were obtained by bubbling palladium-purified Hz through water exhibiting a resistance of 3 megohms. This water was heated with a platinum-immersion heater and was degassed prior to use. Zone melting in a wet-HZ atmosphere resulted in oxidation of the elements which are oxi-dizable with respect to iron. Fine oxide particles were observed on the surface of the liquid zone, and were encased in the bar surface with the passage of the molten zone. Between each zone pass, the surface of the bar was removed by filing and deep etching; this was continued until the oxide formation ceased. The filings were magnetically separated and the residues analyzed by optical spectroscopy. These were especially high in silicon and manganese. Samples were removed from the iron bars, with few exceptions, following each zone-melting operation. A 0.08-in.-thick disc was cut with an Al2O3 cut-off wheel at a point 1/2 in. above the beginning of freezing. Material from each disc was used for hot-hardness measurements, resistivity-ratio measurements, and carbon, nitrogen, and oxygen analyses. Analyses for most other elements were

Jan 1, 1965

By D. M. Boulin, E. S. Greiner

Single crystals of vanadium were bent at 293" and 77°K to a maximum fiber strain of about 1 pct. Analysis of slip line and etch markings of- crystals deformed at either temperature show the slip planes are {112}. The slip directions at 298° and 77°K, deterwined from the asterism axes of rotation of crystals compressed in a {110} direclion, were (111). Etch pits, associated with dislocations, were observed in the plastically deformed vanadium. There was no evidence of mechanical twinning. THIS paper presents results on single crystals of vanadium plastically deformed by bending and compressing at 298° and 77°K. Bcc metals have been observed to slip on {110}, (1121, and (123) planes while the slip direction has invariably been found to be ( 111) 1 Lindley and smallman2 have studied the deformation intension of polycrystalline vanadium between 298° and 20°K and reported that at and above 77°K the deformation is predominantly by slip, but at 20°K the deformation is associated with twinning. Later, Edington and smallman3 found that single crystals of vanadium compressed in a (111) direction at 77°K deformed by twinning on { 112}( 111) systems. Clough and pavlovic4 have reported that mechanical twins were observed in vanadium loaded by impact at 77°, 173°, and 195°K, respectively. PREPARATION OF SINGLE CRYSTALS The vanadium single crystals were made from commercial vanadium reported to contain 0.03 pct C, 0.03 pct 0, 0.02 pct N, 0.0X* pct Ca, 0.0X pct Si, proximately 0.8 cm diam, 4 cm long and were grown in (100) and (110) directions. A crystal for studies of etch pits was gound to have a face parallel to a {l00} plane by the Bond crystal-orienting technique.7 In order to avoid straining, the crystals were placed on the steel mount with a low-melting organic compound (glycol phthalate) before grinding. Crystals for the bending experiments were ground to have the four side faces parallel to ( 100) planes. The crystals were electropolished8 in 10 pct H2So4 using a current density of about 3 amp per sq cm to remove the strained surface material. The crystals were bent slowly by three-point loading in a stainless-steel jig designed by Sylwestrowicz.9 The end rollers of the jig were 3.8 cm apart. DEFORMATION AT 298°K The bent vanadium crystal, after removal from the jig, had a radius of curvature of 20.4 cm over the 2-cm length close to the center loading roller, where the maximum bending moment occurred. This radius of curvature corresponded to a maximum fiber strain of 0.9 pet. The side faces contained slip bands as shown in Fig. 1. These bands are straight where the strain is high, top and bottom of micrograph, but are curved on either side of the neutral axis in the center. This curvature of the slip bands in the low-stress area may be due to cross slip. The plastically deformed crystal was subsequently electropolished and then electroetched in 10 pct H2SO4 solution, using a current density of 0.25 amp per sq cm. The structure is shown in Fig. 2. The directions of the traces on two adjoining faces were plotted stereo graphically, Fig. 3.* Since there were two sets of

Jan 1, 1968

By Mark J. Klein, A. H. Clauer

The Snoek peak induced by solute nitrogen in chromium was studied. A rapid quenching rate is required to maintain nitvogen in solution in sufficient concentrations to be detectable by internal-friction techniques. An expression for the tertninal solubility, c, of nitrogen in weight pevcent is log,,c = -4130/T + 1.05. The diffusion of nitrogen in zhromium determined by internal friction is SNOEK&apos;S theory1 of the stress-induced ordering of interstitial solute elements in the bcc lattice has been used to deduce information on the behavior of interstitials in a number of bcc metals. Under the proper conditions, internal-friction studies of "Snoek peaks" permit a determination of diffu-sivities, solubilities, and precipitation kinetics of interstitial elements. Internal-friction studies of this type have been reviewed by Nowick,&apos; Wert,= Powers and Doyle,4 and others. The behavior of interstitial atoms in Group V-A metals and iron has been rather extensively studied in this way, and results are reasonably self-consistent. However, the study of interstitial elements using internal friction in the Group VI-A metals—tungsten, molybdenum, and chromium—is much less clear. Thus far, internal-friction studies have revealed a peak in tungsten tentatively attributed to carbon5 and a peak in chromium associated with nitrogen. In chromium, Bungardt and Preisendanz6 observed a peak at 180°C for a frequency of -1 cps which they associated with nitrogen. More recently, de Morton7 determined the diffusivity of nitrogen in chromium from studies of a nitrogen peak at 160°c for a frequency of -1 cps and from elastic aftereffect measurements. The objective of this investigation was to study the nitrogen peak in greater detail, to obtain information on the behavior of nitrogen in chromium. This information is of interest because nitrogen is known to have an embrittling effect on chromium. However, efforts to deduce the role played by nitrogen in influencing the mechanical behavior of chromium are handicapped by lack of information on its behavior and distribution in chromium. EXPERIMENTAL PROCEDURES The chromium wires used in these studies were drawn from arc-melted iodide-chromium stock that had been extruded, swaged, and centerless-ground to 0.25 in.-diameter rods. Internal-friction measurements were made in an evacuated torsional pendulum similar to the one described by Kê,8 utilizing wires 0.048 to 0.030 in. in diameter. A series of analyses of the fabricated wires showed that the major impurities were approximately 100 ppm Fe and a combined interstitial content of 50 to 100 ppm C, O, N, and H. A typical interstitial analysis of the wires after processing is 15 ppm C, 2 ppm H, 50 ppm O, and < 5 ppm N. Interstitial concentrations were determined by vacuum-fusion, combustion-conductimetric, and micro-Kjeldahl analyses. In general, vacuum-fusion analysis yielded a lower nitrogen concentration than did micro-Kjeldahl analysis. For consistency, the nitrogen concentrations reported in this investigation were determined by the former method. Heat treatments were carried out by encapsulating the specimens in quartz tubes containing argon. The fabricated wires were annealed at 1150°C for 1 hr to produce uniform recrystallized grain size of about 0.015 mm. Nitrogen and carbon were added to the fabricated wires by encapsulating them in a quartz tube containing ammonia or methane, and annealing them at 1150°C for 48 hr. In some instances, carbon was also introduced by coating the wires with carbon black prior to annealing.

Jan 1, 1965

By Arthur Winslow

Introductory.—The following paper is based upon a report on the lead- and zinc- deposits of Missouri, prepared for the State Geological Survey, which is now being printed. This report is the outcome of work prosecuted by the writer, assisted by Mr. J. D. Robertson, during the past five years. The studies in the State were supplemented by examinations of the similar ore deposits in Wisconsin and Arkan- sas. The report will contain in all about 800 pages, and the aim has been to make it complete and exhaustive, especially in descriptive matter. Naturally, only a brief outline can be presented here, and the reader is referred to the report itself for further details. Contents. I.—History and Statistics, . . 636 II.—Topography of the Region, . 639 III.—General Geology, . . .639 The Archean, . . .639 The Algonkian, . . 640 The Silurian, . . .640 The Devonian, . . 640 The Lower Carboniferous, 641 Tie Coal Measures, . 641 The Tertiary, . . .641 Structural Geology,. . 642 IV.—The Ore-Deposits, . . .643 Geologic Distribution, . 643 The Forms of the Ore-Bodies, . . .641 The Composition if the Ore-Bodies, . . .645 Gangues, . . . 645 Minerals, . . .618 Paragenesis of Minerals, . . . 651 The Structure of the Ore-Bodies, .... 651 V.—Descriptions of Types, . . 652 The Eagle Mines, . . 652 Shaft No. 23, . . 652 The Western Zinc Company or Oswego Lands, 651 The Gobar and Tomlinson Shaft, . 655 The Alba Company&apos;s Mine, 656 The Victor Mine, . . 658 The Bonne Terre Mines, . 660 General Geology, . 660 The Ore-Bodies, . 661 The Vallé Mines, . . 664 The Garatee Mines, . 664 The Corn-Stalk Diggings, . . .665 The Virginia Mine, . 666 The Conlogue Mine, . 667 VI.—The Mode of Formation of the Ore-Bodies, . . 670 The Formation of the Cavities. . . . 670 The Filling of the Cavities, . . . .675 The Formation of the Breccia Deposits, . . 673 The Formation of Circle Deposits, . . .674 The Impregnated Deposits of the Southeast, . 676 VII.—The Origin of the Metalliferous and Other Minerals, 676 1. Originally Deposited in Concentrated Condition, 676 2. Derived from Great Depths, . . .677 3. Original Diffusion, Supplemented by Lateral Secretion, . . . 678 4. Concentrated Through Surface Decomposition, 681

Jan 1, 1895

By Aug. J. Jr. Bowie

(Read at the Wilkes-Barre Meeting, May, 1877.) Brief Outline of the General Topography of the Gold Regions of California. THE topographical features of California, as demonstrated by the explorations of the State Geological Survey, are found to be exceedingly simple. Three equidistant parallel lines can be used in conveying a general idea of the physical geography of Central California. A straight or " main axial line," whose course would be north 31° west, passing through the culminating peaks of the Sierra for a distance of five hundred miles, can be assumed as the eastern boundary of the State. A second parallel drawn fifty-five miles west of the " main axial line" will skirt the western base of the Sierra Nevada, along the edge of the foot-hills. A third parallel run equidistant from the second will represent "as nearly as possible the western base of the Coast Ranges." These parallel lines divide the State into three belts, namely, the Sierra, the Great Valley of California, and the Coast Ranges. " This arrangement of the physical features holds good for a length of four hundred miles in the direction of the main axial line, comprising almost the whole of the agricultural and the greater part of the mining districts."* The section of the country which is of immediate interest to the miner is the western slope of the Sierras. These mountains, rising in a short distance from the Sacramento plains to elevations of over seven thousand feet, with occasional peaks ten and twelve thousand feet high, are cut by numerous deep and precipitous gorges or capons, through which drains the immense watershed of the Sierra, supplying the main rivers of the State and ultimately emptying into the Pacific Ocean. Between these capons, ridges or divides are formed, on top of * See vol. i, p. 5, Geological Survey of California. J. D. Whitney, State Geologist.

Jan 1, 1878

By John B. Myers

Vermiculite is the commercial name used to describe a micaceous mineral that expands appreciably when heated. This process, called exfoliation, results in a light weight material. The light weight material is also called vermiculite, or more exactly, expanded vermiculite. Practically all uses of vermiculite are for the expanded material. Composition and Properties Vermiculite, in its natural state, has the characteristic micaceous habit and a perfect basal cleavage and readily splits into thin laminae, which are soft, pliable, and inelastic. The monoclinic crystal faces are often marked by triangular lines at 60° and 120°. The hardness varies from 1.5 to 2 or more, depending on the composition. The specific gravity varies from 2.2 to 2.7; specific heat 0.2; fusion temperature 2,000° to 2,500°F; luster pearly to greasy; color amber, bronze, brown, dark green, and black. Feel is like talc and sometimes soapy when wet. When heated quickly at elevated temperatures, vermiculite exfoliates by expanding at right angles to the cleavage into long wormlike pieces (the name vermiculite is from the Latin vermiculari, to breed worms). This important characteristic of expansion is believed to be a mechanical separation of the layers when the contained water is converted to steam. The increase in bulk volume of commercially prepared material is 8 to 12 times, but individual flakes may expand as much as 30 times. There is no expansion parallel to the cleavage. Vermiculite may also be expanded by several chemical processes such as soaking in hydrogen peroxide, weak acids and other electrolytes. The color changes during expansion. Heat-treated material changes to a light golden bronze or cream color depending on composition. The conditions of heating affect color. Heating in an oxidizing atmosphere produces reddish colors and heating in a reducing atmosphere produces dull gray colors. The iron is generally not oxidized during chemical expansion. Vermiculite is hydrated magnesium-aluminum silicate. Although there has been much research on the chemical and structural composition, there is not yet complete agreement on the exact formula and composition. This is to be expected since vermiculite is not a mineral of fixed composition and different workers have examined different varieties. It has been proposed that vermiculite is not a single species but a family of related minerals. This has also resulted in many names for the particular vermiculite found in a certain deposit. All of this difficulty arises from the very nature of its crystal chemistry. Unlike most minerals, certain crystal structure properties and the chemical composition can be changed by the ordinary forces of nature or in the laboratory. This would suggest that vermiculite be thought of more as a variable mineral rather than a group of related species. It was stated on page 261 of this volume in the chapter on Clay Minerals by H. H. Murray of the Georgia Clay Co., that vermiculite is an equidimensional, expandable clay mineral. Gruner (ref. 14, Chap. 12) showed that the structure consists of a layer made up of two silica tetrahedral sheets with a central magnesium, iron octahedral sheet separated by two layers of water molecules and adsorbed magnesium and calcium ions. Mathieson and Walker,2a in a recent publication, agree that vermiculite must be regarded as a true clay mineral. The characteristic properties of the mineral, such as high cation ex-

Jan 1, 1960

By James F. Kemp

Discussion of the paper of D. Foster Hewett, Bulletin To. 27, March, 1909, pp. 291 to 310. JAMES F. KEMP, New York, N. Y.:-Mr. Hewett&apos;s paper is one of exceptional interest, because it not only adds an important contribution regarding one of the rarer, valuable elements, but also because it introduces compounds hitherto unknown and in associations no less novel. While we have occasionally dis¬covered and recorded asphaltite in metalliferous deposits, for example in the Joplin and Granby districts, we have not seen a metallic ore in a deposit essentially asphaltite. The source and method of introduction afford a subject well worth serious reflection. Vanadium was first discovered and recognized as a distinct element in the slags obtained in smelting the titaniferous magnetites at Taberg, Sweden. For a long time, therefore, we looked upon the titaniferous magnetites as its hone. Analyses proved, years ago, that it was present in the ores of this type in New Jersey and in the Adirondacks. It was quite rarely determined, but when looked for it was, I think, invariably found, although the Amount seldom exceeded 0.5 per cent. of V,05., In just what combination it exists in the titaniferous ores is uncertain. One might imagine V2O3 replacing some of the Fe2O3 of magnetite; or, since in the lead series vanadates and phosphates are closely akin, one might wonder if a lime-vanadate could take the place of apatite. Yet no lime-vanadate has been found in nature, and apatite itself is usually rare in the titaniferous ores. When percentage-curves are plotted for a series of analyses of the ores, the line of vanadic oxide shows a curious sympathetic behavior with the line of chromic oxide;&apos; but the data are somewhat limited, and no compound has sug¬gested itself which throws light on the matter. Dr. W. F. Hillebrand has discussed the occurrence and dis-

Oct 1, 1909