Search Documents

By Jamie Deuel

The a ad on Connection" For the purpose of this paper, we will concentrate on the ubquitous radon gas as the principle, low-level radiation effect from uranium tailings piles. Standards are also proposed for gamma radiations but, by most accounts, this is much less of a low level problem than is radon. I am also aware of some just completed research at Oak Ridge National Laboratories that suggest polonium may be a major concern in tailings, but those data are preliminary at this time. What is radon gas? In the first place it is not a gas in the accepted sense in that it has no driving pressure head. It might prove a more convenient description to call it radon vapor. Radon vapor, then, is 7-1/2 times heavier than air. Radiologically, it is an alpha emitter which means it spontaneously gives off high ionizing potential but low penetrating power particles. In fact, the alpha particle has such low penetrating power that this sheet of paper will completely shield a person. The problem, though, is breathing the radon decay products, called radon daughters. If radon daughter products are ingested into the lungs, their alpha emissions may cause cancer. The principle carcinoma associated with breathing radon, or more basically, associated with radiological effects is oat cell car- cinoma of the undifferentiated mall cell type. Radon has a 3.8 day half life which means in less than four days half of its initial radioactivity has decayed away. In less than a month it essentially becomes inert or non-radioactive. The Tailings Situation The NRC, in its April 1979 Generic Environmental Impact Statement

Jan 1, 1983

The Committee on Nominations begs to submit the following names as its nominees for the respective offices indicated: For President, SIDNEY J. JENNINGS, New York. For Vice-Presidents, WALTER H. ALDRIDGE, New York; MARK L. REQUA, San Francisco. For Directors, J. E. JOHNSON, JR., New York; ALLEN H. ROGERS, Boston; HOWARD N. EAVENSON, West Virginia; ROBERT M. RAYMOND New York; WILLET G. MILLER, Canada.

Jan 12, 1916

By P. A. Farrar, M. D. Silver, K. L. Komarek

Thermodynamic properties of Hf-0 alloys have been determined from 0 to 25 at. pct 0 between 1000" and 1200°K by equilibrating specimens with alkaline metal oxide-metal vapor combinations. Partial molar-free energies, enthalpies, and entropies of oxygen have been obtained and are conzpared with similar results for the Ti-0 and ZY-0 In continuation of a thermodynamic investigation of the Ti-O and Zr-O systems1 activities of oxygen and lattice parameters of Hf-0 alloys have been deter- system. The positional entropy in all three systems corresponds to an ideal random interstitial solution with one interstitial site per one metal atom. The lattice parameters of hafnium and Hf-O solid solutions have been determined in the range 0 to 20 at. pct O from measurements of Debye powder patterns. mined. All three metals dissolve large quantities of oxygen to form interstitial solid solutions. The phase diagram of the Hf-O system is shown in Fig. 1.' The maximum solubility of oxygen in the cph a phase is considerable (up to 25 at. pct O). The solubility in the high-temperature phase is much smaller. The only stable compound in the solid state is HfO2 which may exist with a certain oxygen deficiency. The low partial pressure of oxygen of Hf-0 alloys required the application of an indirect method. As the most suitable procedure a method, first applied by Kubaschewski to the V-O system,3 was combined with a principle developed by Herasymenko for the

Jan 1, 1963

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By ERNEST W. ELLIS

MORE or less contradictory findings as to the most satisfactory feed for concentration tables of the Wilfley type is shown by the diversity of opinion among experimenters. Prof. R. H. Richards,l as a result of his work, favors classification. On the other hand the work of Messrs. Cox, Gibbins, and Porter,' of McGill University, points in general to the desirability of screen-sized feed The ore used was obtained from the West mill of the Bunker Hill and Sullivan Mining and Concentrating Co., Kellogg, Idaho, and consisted of argentiferous galena in a gangue of quartzite and siderite. The natural feed was taken from the launder supplying the Fahrenwald classifier. Classified feed was collected from each of the ten spigots of this same classifier. From the natural feed the screen-sized feed was pre- pared in the laboratory. All three types of table feed were therefore derived from the actual mill circuit of a large plant.

Jan 1, 1926

By G. W. Form, W. A. Spitzig

The effects of hydrogen and vacuum shtering treatments on the physical and mechanical properties of arc plasma-sprayed tungsten were inuestigated. Temperatures examined ranged from 3000" to 4000°F in vacuum and 2000" to 3000°F in hydrogen for both single and duplex sintering cycles. Densities of 92 pct of theoretical density were obtained when a long-time hydrogen treatment at 2000°Fpreceded sintering in vacuum at 4000°F for 4 hr. This cycle also produced the highest ualues for modulus of rupture and bend angle. The results of this investigation point out the desirability of using a low-temperature long-time hydrogen treatment prior to a high-temperature vacuum sinter for arc plasma-sprayed tungsten. ADVANCES in the development of arc plasma-generating equipment have provided a high-temperature heat source that makes the fabrication of tungsten shapes possible by a metallizing process. Tungsten in the as-sprayed condition is very brittle. It has a density between 80 and 85 pct of theoretical density, a lamellar structure with elongated pores, and a high interstitial impurity content. To improve these properties, sintering treatments can be applied to the as-sprayed material, similar to those used for the densification of compacted tungsten powder. However, in view of the differences in the density and microstructure of as-sprayed tungsten as compared with compacted tungsten, responses to sintering were expected to be different. EXPERIMENTAL PROCEDURES The tungsten powder used in this investigation had a particle size varying from 3 to 13 p with an average diameter of 8p. The impurity level was less than 0.1 pct. The arc plasma spraying was done with an F-40 Thermal Dynamics Corp. plasma jet. Spraying was performed in air and thus required cooling of the substrate by an air blast in order to minimize oxidation. The spraying parameters employed in the fabrication of all specimens are listed below: Power input, kw 12 Arc-gas flow, cfh 95N2 + 5H2 Powder feed rate, g per min 33 Powder carrier gas flow, cfh ION, Spray distance, in. 3 Traverse rate, in. per min 30 Mandrel speed, rpm 100 Nozzle orifice, in. 7/32 These values of the spraying parameters correspond to optimum conditions ascertained in a previous study. Sintering was conducted at 3000°, 3500, and 4000°F in vacuum (< 0.1 Hg), and at 2000 and 3000°F in hydrogen. Duplex sintering treatments investigated are listed in Table I together with the designations that will be used for reference throughout this paper. The samples were fabricated by spraying onto a copper mandrel which was removed prior to sintering. The specimens used for the sintering analyses had the shape of small hollow truncated cones 1 in. high with an inside diameter varying from 0.500 to 0.125 in. and a wall thickness of 1/8 in. Specimens for bend testing were taken from hollow hexagonal prisms 1-1/2 in. high with a 1-in. diam across the flats and a wall thickness of 1/8 in. The bend-test specimens were ground to the dimensions 0.085 by 0.350 by 1-1/2 in. Prior to bend testing 0.0025 in. of stock was removed from each surface by electro-polishing. Density measurements were made by the water-displacement method. In addition, a porosimeter was used to determine the amount of interconnected porosity for representative samples. Strength and ductility were determined from recorded values in transverse bending using a cross head speed of 0.020 in. per min. The load was applied at the midpoint of a 1-in. span. The deflection data reported herein refer only to the plastic portion of the total deflection. RESULTS AND DISCUSSION The as-sprayed samples had a density corresponding to 83 pct (l pct) of the theoretical density of tungsten. Fig. 1 shows a representative as-sprayed tungsten structure.

Jan 1, 1964

By Gerhard Derge

THE introductory paper1 of this series described the potential behavior of tin in sodium carbonate and bicarbonate solutions whose pH ranged from 8.4 to 11.2 and demonstrated that significant and reproducible results could be obtained by proper attention to experimental technique. In examining the corrosion of tin under such conditions, it is desirable to know the effects of anions, aside from carbonate, that are likely to be present in commercial materials packaged in tin. Therefore, in this paper the potential behavior of tin in carbonate solutions to which sodium fluoride, chloride, bromide, iodide, sulphate, nitrate, monobasic phos-phate, dichromate, perborate and acetate have been added will be described. For most of the additions, solutions containing 0.001 and 0.01 .moles of the added material were studied. The experimental procedure was exactly the same as that described in the first paper; the pH of the electrolyte was controlled by adjusting the ratio of carbonate to bicar-bonate as follows: pH 0.1 M NaHCO3 8.4 2 parts 0.1 M NaHCO3, 1 part 0.1 M Na2CO3 9.5 1 part 0.1 M NaHCO3, 2 parts 0.1 M Na2CO3 10.0 0.1 M Na2CO3 11.2 The reagents used were all of C.P. grade. The anions studied may be divided into three groups: (1) anions that had little or no effect upon the potential curves-sulphate, nitrate, and acetate; (2) those that helped to prevent corrosion at low pH only-fluoride, chloride, bromide, and iodide; (3) those that helped to prevent corrosion at high pH also-phosphate, perborate, and chromate.

Jan 1, 1939

By James A. Barr

PUMICE and pumice are varieties of volcanic ejecta formed from lavas of the more silicic types. Chemical analyses of pumice, pumicite and perlite, from which synthetic pumice is now produced, will generally fall within the limits 65 to 75 pct silica, 9 to 20 pct alumina, less than 8 pct combined alkalies (sodium and potassium oxides), less than 3 pct calcium and magnesium oxide, less than 3 pct iron oxide, with smaller amounts of manganese, titanium, phosphorus and other oxides. Perlite is characterized chemically by having, in addition to the percentages of oxides given above, as high as 6 pct combined water. PROPERTIES Pumice is a natural silicic foam glass produced by volcanic eruptions. The molten glass foam, upon rapid cooling, trapped the steam and volcanic gases that caused it to remain extremely porous and vesicular in structure. Pumice is found in the form of large lumps several cubic feet in volume and also in grains only a few millimeters in diameter. Chemically, pumicite is of the same range of composition as pumice. The distinction between pumice and pumicite is one of particle size; the coarser materials are pumice; the fine particles, an appreciable percentage of which is in the range of 100 to 325-mesh or finer, are pumicite. If the erupting volcano ejects a silicic lava containing much gas and water vapor, the sudden release of pressure tends to free the gas. The viscosity of the lava, its rate of cooling and the amount of gas evolved, all have part in determining the degree of expansion of the glassy particles and the fineness of the vesicle. If the lava is of the correct viscosity and there is not too much gas, a pumice may be formed. Large amounts of gas may cause complete disruption into pumicite.30 In 1916, Barbour gave the name "pumicite" to the volcanic ash of Nebraska and since then the name has been widely used in industrial circles for the finer-grained commercial varieties. The glass of pumice and pumicite is transparent and colorless. It

Jan 1, 1949

By T. H. Alden

A correlation has been found in rock-salt structure single crystals between the latent hardening, measured by the direct stress activation of oblique slip systems, and the stress-strain behavior in simple compression. Materials with high latent hardening, like LiF, strain-harden at a low rate (Stage I) even when severely constrained. KCl, in contrast, shows low latent hardening and a tendency to strain-harden at a high rate (Stage 11). This correlation suggests that oblique slip is essential for Stage II hardening of these materials. THE role of secondary slip in the strain hardening of metal single crystals is a topic of lively controversy. On the one hand are theories in which secondary dislocations participate directly in Stage II hardening in the fcc metals, for example through the production of sessile dislocations,1 forest intersections, or jog formation. Much of the experimental evidence on which these theories are based has been reviewed by Clarebrough and Hargreaves.~ On the other hand, a recent theory5 denies that secondary slip has an essential role in Stage II hardening or in the transition from Stage I to Stage 11. In the latter view, Stage I is not terminated by an increase in the activity of secondary systems but by the exhaustion of undeformed material.6 The experiments reported in this paper will not resolve this controversy since the materials being studied are cubic ionic crystals rather than metals. However, the results do show in an unusual way a direct connection between "secondary" (nonortho-gonal or oblique) slip and strain hardening in these materials. Specifically, a correlation has been found between two independently measured properties, first the latent hardening of oblique (110)(1i0) slip systems as measured by direct stress activation of these systems, and second the stress-strain behavior at small strains. From prior work, it was known that in most cubi-cally oriented rock-salt structure crystals, two orthogonal slip systems operate and exclude the other equally stressed pair, oblique to the first pair.7&apos;8 This observation apparently indicates that a significant interference exists between slip on oblique (110) planes and a relatively small interference between orthogonal (110) planes. The present experiments were begun with the intent of obtaining a quantitative measure of this difference by means of a study of latent hardening in these crystals. I) EXPERIMENTAL METHODS The experiments were basically of two types, first the determination of stress-strain curves by compression along a single (100) axis, and second the measurement of latent hardening by compressive prestrain along one cube axis followed by the determination of the yield stress in a second (latent) cube direction. All tests were done at room temperature in an Instron machine by compression between lapped, parallel steel faces. Three specimen shapes were used. For long crystals (nominal dimensions, 1/8 in. square by 1/2 in. long) the ends were lubricated with an oil-graphite mixture. Superior results with short crystals (about 1/8 in. cube) were obtained using 0.003-in. teflon film.&apos; Thin crystals (1/4 in. square by 3/32 in.) were used for latent-hardening measurements and similar results were obtained with either lubricant. Test specimens were cleaved from Harshaw single crystals which had been irradiated to a dose of lo8 roentgen using a cobalt-60 source. The irradiation raises the yield stress and tends to prevent plastic deformation during sample preparation.10 Prior to testing, the irradiation hardening was removed by an anneal at 400°C. Ideal compression specimens have flat, parallel faces. In short specimens particularly, satisfactory results demand a close approximation to this ideal. In the present work, cleaved surfaces were often used directly as compression faces. The degree of success using this method depends on two factors: 1) the smoothness of cleavage faces, and 2) the extent to which the crystal is deformed or crushed by the chisel during the cutting of a long crystal into short pieces. Unfortunately, only one material of those studied, LiF, was completely satisfactory. NaF, NaC1, KC1, and KBr behaved less well so that

Jan 1, 1964

By J. S. Browning

The U.S. Bureau of Mines has been experimenting with flotation processes to separate the spodumene-beryl ores mined at Kings Mountain, N.C. The success to date as well as the present status of the process is discussed. Further experimentation is underway and studies will be made on the milling costs involved in the flotation process. The pegmatites of the Kings Mountain-Lincoln ton, N.C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li,O(lithia) as spodurnene.&apos; The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,-000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2-7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals. Several years ago, the U.S. Bureau of Mines, recognizing the need for developing a large domestic supply of strategic beryl, undertook studies to develop improved methods of recovering this mineral. Because of the low beryl content of the pegmatites, economic production of the beryl entails its recovery as a byproduct of spodumene flotation. Thus, the development of procedures that would provide for maximum recoveries of the spodumene, as well as the beryl, was a primary objective of the studies. Tests were made on run-of-mine ore and spodumene flotation tailing from the Foote Mineral Co.&apos;s spodumene concentrator at Kings Mountain (Fig. 1). Pet-rographic analyses of the ore and flotation tailing are given in Table I. Detailed analyses and examinations of the ore and tailings revealed that the beryllium was present in the form of a low-alkali beryl. The crystals were small, rarely larger than 14-mesh diam, and were clear and colorless. About 10 pct of the Li20 content of the ore was present in the mica and feldspar components of the pegmatite. In some weathered ores the associated clays also contained small amounts of lithia. This is typical of pegmatites in the Kings Mountain area. LABORATORY TESTS In the past, a vigorous chemical treatment of the spodumene surfaces with acid or caustic soda has been considered essential for satisfactory selective flotation of the spodumene from the other minerals in pegmatites. Many tests were made during this investigation to determine if chemical treatment of the spodumene could be eliminated in favor of a reagent combination that would depress the other minerals while selectively floating the spodumene. A simple reagent combination and process was developed that gave better spodumene recovery and grade of concentrate than the more elaborate acid or caustic treatment methods previously used. The finely ground ore pulps were conditioned with either an ammonium, alkali, or alkaline earth lignin sulfonate and sodium fluoride, and the spodumene was floated and cleaned using oleic acid as the collector. The spodumene tailing was deslimed, conditioned with sulfuric acid and coco amine acetate, and floated to reject mica. The mica tailing was thickened and conditioned with hydrofluoric acid, then washed to remove the acid. The washed pulp was conditioned with sodium hydroxide for pH control, and the beryl was floated and cleaned with oleic acid as the collector. Table II summarizes the results of the laboratory test work. About 77 pct of the spodumene and 75 pct of the beryl were recovered from the pegmatitic material. The spodumene concentrate assayed 6.1 pct Li20 and 0.01 pct BeO, and the beryl product assayed 3.0 pct Li20 and 1.57 pct BeO. Similar results were ob-

Jan 1, 1961

By Robert Lowrie

Nine intermetallic compounds were tested in tension at various temperatures. Seven exhibited extensive plastic deformation at elevated temperatures. Correlations of tensile strength and elongation are attempted with melting (decomposition) temperature, valence electron configurations of the component elements, heat of formation, crystal structure, density, and volume decrease accompanying compound formation. A LTHOUGH intermetallic compounds have been -tX known for many years, the study of their mechanical properties, particularly in tension, is just beginning. The problem has been unattractive because of the well-known, erratic behavior of brittle materials tested in tension. The strong influence of surface or internal flaws as stress raisers in non-ductile materials and the effect of eccentricity of loading in superimposing bending stresses on the state of tension in the specimen are extremely difficult to mitigate and impossible to completely eliminate. Thus, tensile properties determined for brittle materials, such as intermetallic compounds at temperatures low in comparison to their melting points, are at best only general guides to the values to be expected in an ideal test of a perfect specimen of the material. It is, nevertheless, surprising that apparently no attempt was made to follow up the pioneer work of Tammann and Dahl1 in this field. Working with crude apparatus, these investigators succeeded in showing unequivocally that at temperatures sufficiently close to their melting points (from 75" to 400°C for the compounds tested) intermetallic compounds did exhibit plasticity. This was indicated by the appearance of slip lines on the surface of the specimen. No observations of strength were made in these tests, which were of a compressive or indentation type. Rossi2 in 1932 attempted to study the physical and mechanical properties of single crystals of a group of intermetallic compounds. However, he was able to prepare only one material, Cu2Z8,, in the form of large, defect-free, single crystals. Thus, he was able to report only the relative fragility of the compounds at room temperature. He reported one compound, Ag,Zn,, to be somewhat plastic at room temperature and Cu,Si to be friable, the latter in agreement with results reported herein. Although test results are available only in classified literature, it has also been announced that MoSi, possesses some ductility at elevated temperatures." In 1948 and 1949 Savitskii and Savitskii and Baron -ublished their work on the hot extrusion of Mg-Zn, Al-Mg, and Cu-Zn compounds. Under the favorable state of stress existing for this process MgZn, MgZn,, MgZn,, ß (Al-Mg), ? (Al-Mg) and 0 (Cu-Zn) could be reduced by amounts up to 90 pct at elevated temperatures. These authors also report that hardnesses of Mg-Zn compounds decrease from room temperature values of about 300 kg per sq mm to 30 to 50 kg per sq mm at 325°C. They found that alloys consisting solely of one Mg-Zn compound were most resistant to softening on heating, mixtures of a compound and eutectic less resistant, and mixtures of two compounds least resistant. The more rapid softening of mixtures of

Jan 1, 1953

The Tuscarora mining district, which has been highly productive of gold and silver ores in past years, is situated about 50 miles north- west of Elko, Nevada. The town of Tuscarora lies at an altitude of about 6,000 ft on the west side of the Independence Valley. Precipitation, particularly the winter snowfall, is considerably greater than in many other parts of Nevada, and temperatures are lower. From Tuscarora can be seen-across Independence Valley in the mountains to the east, a distance of about 12 miles, the Freeport Minerals Jerritt Canyon mine, which seems to be-destined to become one of the great gold mines in the western hemisphere. Tuscarora, a gold and silver camp, was active from the early 1870s to 1903 and produced about $10 million in those 30 years. Ten major mines and several smaller ones were operated in an area of about 1.45 square kilometers (one-half squaremile). The deepest shafts were only 230 m (750 ft) but most of the ore came from about the 105 m (350 ft) levels. Mineralization above the water table, at about 30 m (100 ft), was mostly native silver and cerargerite with free gold. Below the water table the ore was rich in sulfides including argentite, stephanite, proustite, pyrargyrite, enargite, arsenopyrite, bornite, chalcopyrite, pyrite, sphalerite and galena. A number of the properties contain sizeable dumps of what was con- sidered waste rock when it was mined. These dumps aggregate over 408,000 mt (450,000 st) with one dump, the Navajo, containing over one-third of the total. A few grab samples taken in the summer of 1978 from some of the dumps indicated interesting silver values with minor gold content. AgAu Exploration Ltd., was organized to explore and develop these dumps into a heap leaching operation. In the fall of 1978 a campaign was started to lease, with front money payments on a royalty basis, three groups of claims on which were located a few hundred thousand tons of dumps. In September and October of 1978, a systematic program of sampling was started on the Navajo dump which was most favorably situated in that it was near to an area which would furnish good sites for heap leaching pads. At the time it was fully recognized that sampling of dumps was a most difficult problem. Because of the topography on which they were situated and the manner in which they were formed, each dump required its own special sampling technique.

Jan 1, 1981

By S. S. Shen, M. J. Pool, P. J. Spencer

Heats of solution of silver and copper in dilute Ag-Cu-Sn alloys at 720°K have been determined using a liquid metal-solution calorieter. Values of the se2f-interaction coefficient n AgAghave been calculated at constant copper concentrations and n Cu Cuhas been determined at constant silver contents. The reliability of the experimental data is shown by the very good agreement between nCujAg and ij &$; these interaction coefficients have experimental values of -9100 and - 9590 cal per g-atom, respectively. Certain solution models are shown to be inadequate for prediction of solute interaction coefficients in dilute Ag-Cu-Sn alloys. In a previous publication&apos; the results of a thermody-namic study of dilute Ag-Au-Sn alloys were presented. The present work represents the continuation of a program to investigate dilute alloys of the noble metals with tin and in particular is concerned with solute interactions in the Ag-Cu-Sn system. By determination of the magnitude and sign of the various interaction coefficients in dilute alloys it is possible to gain some understanding of the different types of solute-solute and so lute-solvent bonding changes that occur as the solute concentrations are varied. Hence systematic studies of alloys with similar physical characteristics as regards size, structure, electronegativity, and so forth, of their components can contribute a great deal to present theoretical knowledge of solutions. The recent definition of an enthalpy interaction coefficient, 11, by Lupis and Elliott2 is of particular value in calorimetric studies such as the present one: where j and i are solutes and s is the solvent; Si is the relative partial molar enthalpy of component i and x represents the mole fraction of solute or solvent. Values of ?Hi can be obtained directly by solution calorimetry and data for n are thus easily determined, often with a high degree of accuracy. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hi and to the enthalpy interaction coefficients by the expression: ?Hi?Hi + X;nz+ ... [2] The aim of the present work was to determine the self-interaction coefficients n AgAgand 178: in alloys of different compositions and also to establish values for n Agcg| and ncuAg. Since it is a thermodynamic requirement (resulting from the Maxwell-type relationships which can be applied to partial molar properties) that nAgcu and ncuAg should be equal, a further aim of this study was to demonstrate the agreement between experiment and theory. EXPERIMENTAL A description of the liquid metal-solution calorimeter used in this research has already been published,3 and no further details of its construction and operation will therefore be given here. Copper supplied by the American Smelting and Refining Co. was indicated by them as being 99.999 pct pure, and the silver obtained from A. D. Mackay, Inc., was also quoted as being 99.999 pct pure. A solvent bath consisting of between 70 and 80 g of 99.99 pct pure Sn was used for each series of experimental drops. Its weight was accurately determined and the appropriate amounts of copper or silver were added to give alloys of the desired composition. Approximately 0.00125 g-atom additions were used for determinations of the heat of solution of silver in the bath, while, for copper, specimens consisting of approximately 0.0015 g-atom were used. The heat capacity of the bath was determined at regular intervals during a series of drops using tin or tungsten calibration samples. The heats of solution of silver and copper in pure tin were first determined as a function of their concentration in order to establish the self-interaction coefficients 7AgAg and ncucu Alloys containing a constant 0.01, 0.02, 0.03, and 0.04 mole fraction of copper were then used to study 17:: in alloys of different copper content, while alloys of the same mole fractions of silver were used to determine equivalent data for 178: at constant silver concentrations. The composition of the bath was held at the desired copper or silver concentration by making calculated additions of the appropriate solute throughout the experiment. From the limiting values of ?HAg in the constant copper content alloys it was possible to study ?HAg as a function of xCu and hence to determine 42:. A similar analysis of the re, values permitted calculation of nAgcu. Heat content and heat capacity data from Hultgren et al* were used to calculate heat of solution values from the measured heat effects at the experimental temperature of 720°K. RESULTS AND DISCUSSION Determinations of ?HAg. A preliminary investigation of the heat of solution of silver in pure tin at 720°K was first made in order to establish the value of nAgAg before additions of copper were made and also to compare the value of ?HOAg(l) with that obtained in the previous study of Ag-Au-Sn alloys.&apos; Then the heat of solution of silver in Cu-Sn alloys was investigated as a func-

Jan 1, 1970

By H. Ries

SPECIAL sands are those that are employed for special purposes. They have a limited use, as compared with sands for concrete and plaster. The sands discussed in this chapter are those used for foundry purposes, glass manufacture, filter beds, abrasive purposes, sandblasting, engine sand, sand for sheet asphalt, and furnace sand. These sands are almost invariably high in silica, consisting chiefly of quartz grains. In some-for instance, glass sands-freedom from ingredients other than silica, such as iron oxide, is important. Certain grades, like filter sand, require rather careful sizing, and in foundry sands the bond, usually clay, is important. One deposit may sometimes be used to supply several grades or types of sand by appropriate methods of screening and washing. The special sands discussed here are usually obtained from deposits of unconsolidated material but sands high in silica are derived occasionally from soft sand- stones that can be disintegrated easily. Requirements are not the same for all uses, and, while certain properties may be demanded, there are no officially adopted standard tests except for foundry sands. FOUNDRY SANDS Definition-Foundry sands include those siliceous sands that are used to make the forms for casting metals. If these are employed for making molds, they are known as molding sands; if for the cores that form the hollow spaces in the casting, they are called core sands. Naturally bonded sands are those containing a variable, though not usually large, amount of clay, which serves as a bond. Synthetic sands, now much used, represent an artificial mixture of sand with usually fire clay or bentonite. Core sands may be bonded with oil, cereal binders, resin, pitch, or other materials. The foundrymen apply the term "sharp sand" to one that is free from bond. Properties-The important properties to be tested at room temperature are texture or fineness, permeability, strength, deformation, and flowability. Those tested at elevated temperatures are compressive strength, expansion and contraction, sintering point, and durability. More attention probably has been given to research on the properties

Jan 1, 1949

By John T. Norton

In spite of the very general errlployment of nitride hardening, there is still considerable doubt as to the real nature of the mechanism involved. Experience has shown that the addition of small amounts of hardening elements to iron or steel results in a wide variety of desirable properties in a nitrided case. Perhaps the foremost of these elements is aluminum and in this investigation an attempt has been made to study the behavior of aluminum during the hardening process. It is believed that the establishment of a complete atomic picture of the metal at various stages of the process will indicate the relationships between the several kinds of atoms and their individual influences on the physical properties in a clear and direct fashion. A consideration of the problem suggests a surprising similarity between the mechanisms of nitride hardening and of age-hardening. It is now generally understood that age-hardening may take place by one of two distinct processes, the first involving the precipitation of a finely dispersed phase and the other being concerned with the modification of an existing phase. Following much the same line of reasoning, two theories of nitride hardening have been suggested. The first explanation, which has been generally discussed, particularly by Fry,&apos; states in brief that the presence of aluminum causes the precipitation of aluminum nitride during nitriding and that this finely dispersed phase is the primary cause of hardening. The second explanation, which has not been published but which has been freely discussed by those interested in the problem, postulates the substitution of aluminum atoms for certain of the iron atoms in the several iron-nitrogen phases in the same manner that the substitutional iron-alurninurn solid solution is formed. The marked increase in hardness, as compared with the aluminum-free system, is attributed to the severe lattice distortion accompanying this replacement.

Jan 1, 1934

By T. W. Guy

DURING recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years-at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures.

Jan 1, 1931

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half&apos;-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.&apos;&apos; The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

By K. C. Sclater

GAS as a factor in the efficiency of oil production, might be a better title for this paper as it deals in general with the significance of the gas-oil ratio as an index of the efficiency of oil production and briefly discusses oil production methods with reference to the gas-oil ratio in wells, particularly during the early life of a field. In the recent hearings held at Washington before the Federal Oil Conservation Board the fuller utilization of the energy contained in the gas occluded in or associated with the oil underground was stressed by some of the speakers when referring to greater ultimate recovery of oil. One speaker commenting on this point said in part, "There is ample evidence indicative that if the gas associated with the petroleum in our fields were conserved and elevated gas pressure maintained in the oil sands during their productive life, the ultimate production of oil could be greatly increased."

Jan 1, 1926

By J. G. Kura, P. D. Frost, L. W. Eastwood

THE preparation and general properties of mag-nesium-lithium base alloys have been described in earlier papers.l,2 Lithium forms solid solutions with pure magnesium, lowers its density, and improves its formability. The improved isotropy and better formability of these alloys are attributed to the ability of lithium to convert the magnesium lattice from hexagonal (alpha phase) to body-centered-cubic (beta phase) structure. This change in structure is, however, accompanied by some limitations which make it difficult, if not impossible, to combine all the desirable properties in one composition. The most important of these limitations is the tendency of the high-strength alloys to overage and lose strength at temperatures of the order of 150" to 200°F. A study was made of the effects of composition and heat treatment on the age-hardening character- istics of the alloys. Stability of properties was determined by hardness and tensile testing of the alloys at room temperature after various periods of exposure to elevated temperatures. Precipitation-hardening curves are shown for a number of magnesium-lithium-zinc alloys in fig. 1. All the alloys were solution treated at 700°F and aged at 200°F. The reason for using the drastic quench, toluene at —105°F, was to reduce the rapid precipitation of the hardening phase which takes place at room temperature. Previous experience has shown that a hardness of about 90 to 95 Rockwell E is indicative of yield strengths in the range of 35,000 to 40,000 psi. This is a desirable strength level for magnesium-lithium base alloys with specific gravities of the order of 1.65 or less. Although the hardness level is raised by large zinc contents, a corresponding decrease in the cold formability of these alloys occurs with increasing zinc content. Thus, alloys containing up to about 10 pct Zn and having hardnesses of the order of 70 to 75 Rockwell E may be bent over a very small radius; however, the 16 pct Zn alloy requires a bend radius of more than 8T. The hardness relationships illustrated in fig. 1 can be explained by the partial phase diagram shown in fig. 2. The zinc-free magnesium-lithium alloys are entirely body-centered cubic (100 pct beta phase) when the lithium content of the binary is 10.3 pct or higher. When zinc is added, the boundary between the beta and alpha-plus-beta fields at 700°F is shifted to lower lithium contents. In addition, the solubility of zinc at 700°F decreases with decreasing lithium content. It is shown by a study of micro-structures that the limit of solid solubility of zinc in the 6Mg/Li* matrix at 700°F is about 19 pct. It is believed from a study of the aging curves that this limit is about 2 to 3 pct at 200°F. Zinc additions up to about 2 pct increase the hardness and strength of the magnesium-lithium base solid solution. Larger additions of zinc effect further hardness increases, but precipitate during prolonged aging at 200°F. Alloys having 14 to 20 pct Zn precipitation harden extremely rapidly during quenching, even when quenched in toluene at —105° F. The high-zinc alloys overage at 200°F but are capable of maintaining reasonably high hardnesses for periods up to 1000 hr.

Jan 1, 1951