Search Documents

By C. W. Lawr

THE ores mined by the Santa Gertrudis Co. at Pachuca, Mexico, are mainly silver-bearing; they also yield some gold and carry a little copper. Strong cyanide solutions are used to dissolve the silver and gold, and the mechanical loss of cyanide at the tailings filter has been considerable. Prior to the year 1923, the pulp, after agitation, was given a 35 to 37-min. wash with barren solution in a Butters-type leaf filter; the discharged slime cake was repulped and pumped into eight Merrill self-sluicing slime presses in which the slime was given a further wash with barren solution for 25 to 35 min., followed by a 10-min. water wash. At that time the barren solution titrated around 0.350 per cent. free KCN and 0.500 per cent. total KCN. (Aero brand cyanide is used.) It can readily be seen that a 10-min. water wash would leave considerable cyanide in the filter cake, which of course was a total loss. This averaged 0.522 kg. (1.15 lb.) KCN per ton of solution. As the daily discharge to. the dam was 1600 tons1 of slime of a 2: 1 ratio of liquid to solid, the value of this mechanical loss of cyanide was an important item and its recovery held alluring possibilities.

Jan 1, 1929

By C. M. Loeb, A. M. Gaudin, J. H. Brown

THE object of most size reduction operations in the mineral industry is to liberate the grains of valuable minerals in the ore from those of the gangue. This is usually accomplished by crushing and grinding the entire mass of ore until there is only a small probability that any single particle contains more than one mineral. During this size reduction only limited control exists over size or composition of the particles exposed to the breaking action, and there is no control over the paths followed by cracks generated during the operation. This lack of control usually results in overgrinding and in production of large quantities of very fine material. The first detriment, overgrinding, is costly in itself, but when combined with the second factor it is doubly so. Not only is the fracture of a free particle unnecessary—the fracture of these particles may also make subsequent separation operations difficult, inefficient, and wasteful. It has been pointed out' that if the object of size reduction is to liberate the valuable mineral component of the ore then, ideally, fracture should follow intergranular paths to the exclusion of trans-granular ones. This would result in liberation of the valuable minerals with as little size reduction as possible. This ideal comminution operation is referred to as intergranular comminution, and it was the object of the investigation to determine the extent to which it could be developed by heat treatments. There are many indications in the literature that heating rocks prior to crushing may be favorable. Reports by Holman,2 Yates3 and Myers' are pertinent. These investigators showed that heating certain rocks prior to crushing them did, in fact, improve their crushing characteristics in that fewer fines were produced, although the fact that intergranular comminution was being effected apparently was overlooked. In addition, Sosman noted that if there is appreciable anisotropism in the thermal coefficients of expansion of even a pure mineral, then considerable permanent separation of the grains of the rock can be expected as a result of heating the rock to a high temperature.' By the same token, if there are ap- preciable differences in the thermal expansion coefficients of the various minerals of a multi-component rock, similar results should be obtained by heating this rock. This has been tested, partially, by Brenner," who obtained patents covering the heat treatment of some pegmatitic rocks in order to facilitate comminution of these materials. It has also been demonstrated that this may occur in taconite." Also, the possibility of causing decomposition of one mineral in a rock as a means of promoting intergranular fracture has been considered. Seigle2 and Schiffman et al. have obtained patents on such processes as applied to calcareous iron ores. These reports all indicate that heat treatments prior to crushing may contribute materially to intergranular comminution, but they also indicate that no organized attempt has been made to determine the controlling factors of the method or to determine its applicability in general. The present article is a report on the initial phase of such an investigation. The authors have reviewed the claims of prior investigators and have attempted, also, to establish the factors that might determine the applicability of heat treatments in the mineral industry. In this work 2000-g samples of various rocks were heated in a small laboratory furnace and crushing and sizing operations were carried out in standard laboratory equipment. All samples of each rock were as nearly identical as possible in particle size, grain size, and composition and contained only lumps coarse enough to contain many grains each. Tests on Granite A number of tests were made on a coarse grained Finnish granite obtained in the form of coarse chips from a local monument yard. This rock exhibited little variation from piece to piece in either composition or grain size. The minerals contained were quartz, orthoclase, small amounts of hornblende, and minute quantities of mica. Grain size ranged from about 1 mm to about 3 mm. Temperature of the Heat Treatment: In some cases the granite was heated to a particular temperature and crushed, hot, immediately upon withdrawal from the furnace—in others the rock was allowed to cool before crushing, but without quenching to room temperature after heating. In most tests on granite the heating period was about 2 hr with the furnace at the highest temperature for about 1 hr. Cases in which these periods were varied greatly will be presented separately.

Jan 1, 1959

By C. C. Martin, M. C. Fuerstenau, R. B. Bhappu

Experiments revealed that quartz could not be floated in conductivity water at any pH with a long-chained sulfonate as collector. Various cations, Fe+++, Al+++, Pb++, Mn++, Mg++, Ca++, are shown to function as activators when the pH is such that the cation hydrolyzes. As the solubility product of the various cation-sulfonates was exceeded at the concentrations involved, precipitated cation-hydroxy-sulfonates, e.g. Fe (RSO3)2OH must be functioning as the collector in these systems. A number of interesting and important phenomena were revealed during a study of the response of beryl to sulfonate flotation.' Perhaps the most important observation is the effect of various cations on flotation response. Experiments showed that in the vicinity of pH 3.0, about three ppm Fe+++ increased recovery of leached beryl from about 60 pct to 100 pct, whereas about four ppm Ca+ + reduced the recovery from 60 pct to 2 pct. With the exception of ferric iron, all of the other cations investigated reduced flotation recoveries drastically at this pH. As postulated in the paper Sulfonate Flotation of Beryl,' even with low concentrations of polyvalent cations and sulfonate (on the order of one ppm), cation-sulfonates are precipitated immediately in solution. That is, blueish-white clouds were noted to form after given additions of salts to known solutions of sulfonate. Furthermore, it was also shown that one-hundred-fold more ferric iron than necessary to form the precipitated cloud had to be added to effect complete flotation. In other words, some form of solid ferric sulfonate was found to function as the collector in these systems. The form of the compound was suggested to be Fe(RCO3)2OH and that bonding to the surface occurs through the hydrogen of the hy-droxyl. As the form of this compound was shown to be dependent on the extent of hydrolysis of ferric iron, it is to be expected that ferric iron will be unique in some pH region. Further, if the presence of hydroxyl in the neutral precipitated compound is of primary importance, then other cations should function similarly but at different values of pH, since they will hydrolyze at different concentrations of hydroxyl ion. To determine whether the premise of hydrolysis is correct, the study was extended to quartz systems in the presence of various cations at various values of pH. EXPERIMENTAL MATERIALS AND METHOD Sodium alkyl aryl sulfonate was chosen as the collector for the experimental work. The reagent, sup plied as a courtesy sample by the Shell Chemical Co., has the following physical properties: Physical form Solid — Finely ground Sulfonate content, pct wt 95 to 97 Molecular Weight 450 to 470 Number of carbon atoms in hydrocarbon chain 25 to 30 Melting Point, OF 250 to 260 Solubility Soluble in water with gel formation at concentrations higher than 25 pct by weight sulfonate This particular reagent was chosen because of its high active sulfonate content, long-chain length, and solid form. With the exception of the frother and sulfonate, all other chemicals were of reagent grade quality. Conductivity water was used in the experimental work. This water, made by passing distilled water through an ion exchange column, had an average measured conductivity of one micromho. Experiments were conducted at room temperature in a small glass flotation cell with the following procedure: 1) A redetermined amount of water and salt solution (e.g. CaC12 . 2H2O) were combined and the pH adjusted to a given value. 2) A given amount of sulfonate was added so that final solution volume was 130 cc. 3) One drop of Dow 250 frother was added. 4) Five g of quartz were added and the system conditioned for five minutes. 5) The pH of the system was measured (termed flotation pH).

Jan 1, 1963

By C. S. Smith, E. W. Palmer

IN 1934, when Gregg and Daniloffl wrote their excellent monograph on the alloys of iron and copper, the most recent literature on the constitution of the alloys indicated a narrow single-liquid area for 20" above the liquidus with a closed liquid mis-cibility gap above this. Since that time, however, a number of investigators have confirmed the much earlier studies of Mushet2 and Stead3 who, among others in the nineteenth century, had described the true state of affairs. Liquid copper and iron are completely miscible in the absence of carbon, but small amounts of carbon cause liquid segregation. In 1934, one of the writers' mentioned evidence for the absence of liquid separation in carbon-free alloys at temperatures up to 1700°C. Two years later, Mad-docks and Claussen5 unequivocally established the absence of liquid segregation and published a revised diagram, reproduced in fig. 1. They also studied the limits of the two-liquid area in ternary alloys of iron, copper, and carbon as a function of carbon and iron content. In the same year Simpson and Bannister" and Schumacher and Souden7 described in some detail the properties of alloys containing 50 to 75 pct Cu. More recently Hodges et al.16 have developed the copper-rich alloys for use as high-strength conductors. In 1937, Iwase, Okamoto, and Ameniya8 published data on the miscibility gap in ternary alloys of iron, copper, and carbon that supported the conclusions of Maddocks and Claussen, and definitely located the two-liquid area at temperatures of 1450" and 1540°C. They also reported that additions of 1 pct Al, Ni, Pb, Sn, or Zn caused no segregation in 50 pct Cu alloys at 1540°C. The use of copper in amounts approximating 1 pct has found industrial employment to an increasing degree in both wrought and cast steels, for such steels are capable of being precipitation-hardened following normalizing, and have high yield strengths. This is summarized by Gregg and Daniloff,1 Sallitt,9 and Lorig and Adams,10 while Alexander" gives additional information on the heat treatment of copper-steel castings. Lippert12 has described Digby's two-phase steels containing copper and chromium. The work described in the present paper was done in the years 1932 to 1934, at which time much of the information was new. The excellent work subsequently done in other laboratories but more promptly published makes the present paper in part only a confirmation of what is now well known. There has not, however, been published any unified study of

Jan 1, 1951

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

By Emerson F. Heald

A systematic study was made of new and old data on chemical activities in Fe-Pt alloys at elevated ternperatuves. Experimental results may be expressed in terms of the excess free energy using Least-squares analysis of the data gave the following values for the constants: for the temperature range 1130° to 1350°C, and tentatively to 155O°C, B = -3.326564 and C = 0.221051; for the temperature range 650" to 850°C, B = -2.555690, C = 1.762735, and D =0.097196. In the study of iron-containing silicate systems, it is sometimes desirable to have a direct experimental measure of the activity of iron in the system. The well-known solubility of iron in platinum, often a headache in experimental work on iron compounds under reducing conditions, can be used to advantage in this respect. If the activity of iron in an Fe-Pt alloy in equilibrium with the silicate is known as a function of the composition of the alloy, chemical analysis of the alloy will give a knowledge of the activity of iron in all of the phases in the system. The present study was undertaken in order to elucidate the characteristics of Fe-Pt alloys as iron activity indicators. This work is intended to tie together some previous work, which may be summarized as follows. Larson and Chipman1 determined the activity of iron in Fe-Pt alloys at 1550°C by equilibrating platinum metal with calcium oxide-iron oxide-silica melts of known iron activity. Compositions of the resulting alloys were determined by chemical analysis. A similar study was carried out by Taylor and ~uan,' who worked at 1300°C. They brought the Fe-Pt alloys into equilibrium with iron oxide under conditions of known partial pressure of oxygen, and thus, from the work of Darken and ~urr~,~ conditions of known iron activity. Compositions were determined indirectly, by following the change in weight of the sample. Sundaresen et el* used the electromotive force of cells in which the alloy formed one electrode in order to measure the activity of iron in the alloy at 650" and 850°C. These temperatures were chosen to be above and below the first-order phase transition which takes place upon the ordering of Fe3Pt and the second-order transition which occurs upon the ordering of FePt3. EXPERIMENTAL 1) High Temperatures. The starting materials used were thin platinum foil, about 0.002 mm thick, and Fisher Certified reagent ferric oxide, Fez03, which had been heated for 24 hr at 1000°C. An intimate mixture of 80-mesh Fez03 and platinum platelets was placed in a thin platinum foil envelope. The latter was suspended from thin platinum wires in the hot zone of a vertical-tube, platinum-wound furnace of the type described by Muan and ~sborn.~ A capillary gas mixer similar to that used by Darken and Gurry3 was used to prepare a precisely known mixture of carbon dioxide and hydrogen, which was allowed to flow upward through the furnace tube. The partial pressure of oxygen in contact with the sample was thereby fixed at a value which was calculated from the charts prepared by porter? Temperatures were measured with a Pt-10 pct Rh-in-platinum thermocouple, which was calibrated using the melting points of gold (1062 .@C) and diopside, CaMgSizOB (1391.5"C). Temperature control was maintained to within i3"C with a Geophysical Laboratory proportional controller, using the furnace resistance as the sensing element. Samples were quenched by passing a small current through the platinum suspension wires, allowing the sample to drop into a bath of dibutyl phthalate at the bottom of the furnace tube. Prior to chemical analysis the samples were washed with acetone and dried. 2) Chemical Analysis. It proved possible, in almost all cases, to separate the Pt-Fe platelets physically from particles of iron oxide. The platelets were dissolved in a small volume of aqua regia, evaporated to dryness, and redissolved to 0.1 M HC1. In order to determine iron in the platinum alloy potentiometrically, it is necessary first to remove the platinum. A 10-cm column of Amberlite IR-120 cation exchange resin in the hydrogen form provided separation quickly and quantitatively: The mixture of iron and platinum in 0.1 M HC1 was added to the top of the column, and washed with about 100 ml of 0.1 M HC1. Under these conditions, the iron, principally in the form of cations such as FeC1" and FeCl;, is held quantitatively in the uppermost centimeter of the column. The platinum, in the form of anions such as PtC&- , is washed through without being adsorbed. After a qualitative test with stannous chloride indicated all of the platinum was removed, the iron was

Jan 1, 1968

By James K. Stanley

WHEN a plastically deformed metal is heated to a certain temperature, it undergoes a complete change in microstructure, the consequence of which is a marked alteration of mechanical properties such as hardness, strength and ductility. This change in microstructure occurs by recrystallization and is a process involving the formation and growth of strain-free nuclei in the deformed matrix. These nuclei continue to form with time and grow until a new grain structure replaces the cold-worked structure. The formation of the nuclei in the deformed sheet of 1 per cent silicon ferrite is illustrated in Fig. 1. If a recrystallization is conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time leads to an isothermal recrystallization curve, first established in 1942.1 Such recrystallization curves are shown in Fig. 4. These curves show that the recrystallization of a cold-worked metal is best considered as a rate process rather than a time independent process such as is suggested by the improperly named and misleading recrystallization diagrams involving deformation, temperature, and grain size. 2-5 Any study of the rate of recrystallization resolves itself into a study of the component rates of nucleation and growth. The previous paper' provided an account of the determination of the rates of nucleation; N, the number of nuclei formed per unit time per unit of unrecrystallized area, and growth, G, the radial growth in unit time, in the recrystallization of silicon ferrite (1 per cent Si). A method was developed to furnish experimental data for evaluating the effect of the recrystallization variables on N and G. The mathematical analysis for the derivation of the isothermal recrystallization curve was developed for a two-dimensional case (in thin sheets where the diameter of the recrystallized grain is greater than the sheet thickness). The present paper is a continuation of the study of recrystallization of 1 per cent silicon ferrite begun in 1942.1 In this work the effect of the factors deformation, temperature, grain size, composition, and recovery is studied with respect to the rates of nucleation and growth. At the same time it is shown how the cooperation of N and G affects the isothermal recrystallization curve. The study of these variables on N and G has a definite bearing on the mechanism of recrystallization and should lay a foundation for a rational theory on the subject. PROCEDURE The procedure used in these experiments was essentially the same as that described previously but in certain details some changes were made in the interests of speed. With few exceptions, the procedure is the same for the study of all the variables. Where the procedure is different from standard manipulations attention is called to this fact.

Jan 1, 1945

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By C. L. Mantell

ALTHOUGH SO common and well known a metal, tin is really a less abundant element than many of those less familiar and usually ranked with the scarce or rare elements, such as cerium, yttrium, lithium, beryllium., titanium, zirconium and vanadium. The color of tin is white, with a slightly bluish tinge. When it is compared with nickel, the latter metal is brown. When placed alongside of tin, chromium is definitely blue. Tin is whiter than silver or zinc. Exceedingly thin films of tin show various shades of brown by transmitted light. The metal has a brilliant luster, and when mirror-polished, has high light reflectivity. The luster depends to a large extent upon the pouring temperature at which the metal is cast. If the temperature be, too high, iridescent colors may show on the surface. These are the result of oxide film formation. If the pouring temperature be too low, the surface is dull. Small amounts of foreign metals, such as lead, arsenic, antimony and iron, decrease the luster of tin and impart a yellowish tinge to the metal. The structure is decidedly crystalline. The cast metal is a mass of crystals. When a bar of tin is bent, it emits a characteristic creaking sound. This is called the "cry" of tin, resulting from the grinding of the crystals one against the other during the bending of the metal. Tin metal may lose its crystalline structure by cold working, but grain growth occurs rapidly under the influence of heat. Metal which has been cast at a low temperature may become amorphous as the result of mechanical work. If such material be heated to temperatures well. below the melting point, say at 110° C. for a half hour or for a few minutes at 150° C. recrystallization occurs. If the surface of tinned plate, tin foil, or tin metal in cast form be etched with hydrochloric acid containing a little free chlorine, attack occurs at the intercrystalline faces. The surface shows patterns resembling the frost flowers on window panes in winter. The etched appearance is called moiré metallique. Fine dendritic surface crystals of tin may be obtained by casting the metal on a surface of polished steel. In commercial tin plate, the intercrystalline boundaries are shown by fine grooves or channels, which result from the method

Jan 1, 1929

By G. R. Belton, R. J. Fruehan

The Knudsen cell-mass spectrometer combimtion has been used to study the Fe-Al and Ag-Al liquid alloys. By application of the recently developed integration technique to the measured ion-current ratios, activities have been derived for the Fe-A1 system at 1600° C and for the Ag-Al system at 1340"C. The results are partially represented by the following equations: Internal consistency between the data on silver-rich and iron-rich alloys is demonstrated by application of the literature measurements on the distribution of aluminum between the nearly immiscible liquids iron and silver. The usual restrictions on the ratio of the mean free path of the escaping atoms to the orifice diameter of the Knudsen cell are shown not to be limiting in this technique. DESPITE the importance of a knowledge of the activity of aluminum in understanding deoxidation equilibria in molten steel, no direct studies have been made of activities in liquid Fe-A1 alloys at steel-making temperatures. Lower-temperature direct studies have, however, been carried out on aluminum-rich liquid alloys by Gross, Levi, Dewing, and Eilson' at 1300°C and by Coskun and Elliott' at 1315°C. Apart from phase diagram calculations by Pehlke, other determinations have been indirect and were made by measurement of the distribution of aluminum between iron and silver475 and combination of these data with extrapolated activities in the Ag-A1 system.~-% ecently, however, Woolley and Elliott have made a significant contribution by directly measuring heats of solution in the Fe-A1 system at 1600°C. The present authorslo have recently employed a Knudsen cell-mass spectrometer technique in a study of activities in iron-based liquid alloys. In this technique activities and heats of solution are determined from a series of measurements of the ratio of ion currents of the components; and since ion-current ratios are used, problems caused by changes in instrument sensitivity or cell geometry are overcome. Results obtained for the Fe-Ni system were found to be in excellent agreement with previous work, thus demonstrating the reliability of the method. The present paper describes a similar study of activities in the liquid Fe-A1 and Ag-A1 systems, this latter system being included in order that a meaningful comparison can be made with the above-mentioned indirect studies. INTEGRATION EQUATIONS A detailed derivation of the equations used to determine the thermodynamic properties from the measured ion current ratios has been given elsewhere;'' however it is useful to summarize them here. By the combination of the Gibbs-Duhem equation with the direct proportionality between ion-current ratios and partial pressure ratios, it was shown that for a binary system at constant temperature and pressure: where al is the activity of component 1 with pure substance as the standard state, N, is the atom fraction of component 2 in the solution, and I; and t'2 are ion currents of given isotopes of the components. The activity coefficient is given by: this latter equation being more suitable for graphical integration. Combination of Eq. [l] with the Gibbs-Helmholtz equation gives an expression for the partial molar heat of mixing: EXPERIMENTAL A Bendix Time-of-Flight mass spectrometer model 12! fitted with a 107 ion source and a M-105-G-6 electron multiplier, was used to analyze the vapor effusing from the Knudsen cell. The arrangement of the Knudsen cell assembly was essentially that of the commercial instrument (Bendix model 1030) but with several modifications. Instead of heating with a single tungsten filament, a cylindrical tantalum-mesh heater was employed. Up to 1400°C simple resistance heating was used but above this temperature electron bombardment between the tantalum mesh and the tantalum cell susceptor was necessary. The temperature was measured by means of a Leeds and Northrup disappear ing-filament type optical pyrometer sighted on an essentially black-body hole in the side of the cell. Details of the temperature control, temperature measurement, and in situ calibration of the optical pyrometer can be found elsewhere.I0 In the investigation of the Fe-A1 system the Knudsen cells were constructed of thoria crucibles with fitted thoria lids (Zircoa). The cells employed in investigating the Ag-A1 alloys were made up of high-purity alumina crucibles (Morganite) with lids of recrystal-lized alumina (Lucalox). The cells were 0.370 in.

Jan 1, 1970

Mining Methods LUCIEN EATON, Chairman S. R. ELLIOTT, Vice-chairman CHARLES W. WRIGHT, Secretary Alluvial Mining CLINTON BERNARD CHARLES JANIN O. J. EGGLESTON CHARLES H. MUNRO N. L. WIMMLER Open-cut Mining Iron MAX H. BARBER J. A. MACKILLICAN KENNETH DUNCAN W. R. VAN SLYKE

Jan 1, 1932

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By John Birkinbine

The experience of the past five years has furnished opportunities to study and to partially explain the operation and some of the causes of the short blast of Warwick Furnace at Pottstown, Pennsylvania, as described in the paper read at the Lake Superior Meeting, in August, 1880.* The many inquiries concerning the details of furnace operation which followed the publication of the paper, and the expressed desire of furnace managers to be informed as to future operations of this plant, have encouraged the preparation of the following data. To make the record continuous, and add to the value of both contributions, the present paper commences where the review of a short blast of Warwick Furnace ended, and includes the data of another short blast of two months, and a subsequent continuous campaign of nearly five years, which, by comparison, we shall designate as "the long blast." Frequent visits to the plant in the five years, during which its operation could be studied, and correspondence with the manager, Mr. Edgar S. Cook, have given a knowledge as to general features and details, and the courtesy of the officers of the Company which has given free access to the books of record permits the presentation of data which it is believed will be welcomed by furnace managers. Interest will undoubtedly be increased by the remarkable results which Mr. Cook has achieved chiefly with anthracite coal in a furnace whose details of construction will scarcely be generally admitted as embodying advanced ideas, its height being but 55 feet, with a bosh diameter of 15 feet 6 inches, its bosh-slope comparatively flat, its crucible smaller than the average, and the heat of the blast never reaching 1000' Fahrenheit. At present writing the credit of the best anthracite blast-furnace practice recorded in our Transactions is conceded to be that pursued by Mr. Fackenthal, at the Durham furnace, and Mr. Cook, at War-

Jan 1, 1886

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 1/4 to M in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles. Because rock salt is an inexpensive commodity, a low-cost process was required. Gravity methods were, of course, considered. The heavy-liquid separations indicated that a split at an effective specific gravity of 2.2 to 2.3 would be required. (The specific gravity of pure halite is 2.16.) Heavy-media separation was investigated but had the disadvantages that it was necessary both to operate with saturated brine and to dry the cleaned salt, and that the cleaned salt was darkened by the magnetite medium. Air tabling was tried but did not give the desired separation. It soon became apparent that established methods would not provide a satisfactory solution and work was undertaken on the development of a new process to solve the problem. PROCESS DEVELOPMENT Preliminary Experiments: At the start of the investigation, an analysis of the problem indicated that the diathermacy of rock salt—that is, its ability to transmit radiant heat—might form the basis for an efficient separation process. Under this theory, the impurities might be selectively heated by radiant heat. The particles could then be fed over a belt coated with a heat-sensitive substance so that the warm impure particles would adhere preferentially to the coating. After the initial experiments, made by heating the rock salt with an infrared lamp and separating the product on small sheets of resin-coated rubber, proved encouraging, a small continuous separation unit was set up. This comprised 1) a simple heating unit consisting of a vibrating feeder covered with aluminum foil and an infrared lamp mounted above the feeder and 2) a separation belt 6 in. wide and 36 in. long. A sketch of the device is shown in Fig. 1. Results with this apparatus confirmed the fact that a good separation was possible. It was apparent, however, that a considerable amount of experimental work would be needed to develop the scheme to a practical and economical process. The Process: Basically, the process consists of two main steps: 1) selective heating by radiation and 2) separation of the heated particles on a heat-sensitive surface. Because neither of these steps had previously been utilized commercially in mineral processing, it was necessary to do basic research on both aspects. Factors studied in the investigation included type of heat source, design of heating unit, design of separation belt, selection of heat-sensitive coating, removal of heated particles from the belt, contact between particles and coating, and maintenance of the heat-sensitive surface. Part of the experimental work was carried out on a small-scale unit consisting of the 36x6 in. belt and auxiliary apparatus, and part on a larger unit. For simplicity, discussion of work on both of these units is grouped together. SELECTIVE HEATING Radiant-Heat Source: The essential requirements for a radiant-heat source were 1) that the radiant heat be in a wave length range which is effectively absorbed by the impurities but not absorbed appreciably by the rock salt and 2) that it be dependable, practical, and economical. Selection of a heat source of suitable wave length range was one of the first considerations. It is well known that pure halite is highly transparent to radiant energy in wave lengths from 0.3 to 13 microns. However, the available data on infrared transmission by dolomite and anhydrite, particularly in the range below two microns, were not complete enough to serve as a reliable basis for selection of a heat source. Although it may have been possible to obtain sufficient data on infrared transmission and absorption to enable one to select the best heat source, a more direct procedure was used. This consisted simply of exposing the crude rock salt to each of several types of radiant-heat source on the small continuous separation device. The heat sources investigated, approximate source temperature used, and calculated wave length of maximum radiation are tabulated in Table I. Of the two types of tungsten-filament lamps investigated, both the short wave length photoflood lamps and the longer wave length infrared lamps were satisfactory from the standpoint of selectivity

Jan 1, 1961

By Herbert C. Hoover

While the importance of the superficial alteration of golddeposits is recognized in pure science, it seems often to be singularly disregarded among engineers in practice. Its great practical bearing lies in the exploitation of new regions; and nowhere are the disastrous results of ignoring it more vividly shown than in Western Australia, where the impoverishment of the ores, and their frequent transition from free-milling' to refractory character in depth (things, as a rule, neither anticipated nor ascertained by exploration beforehand), have brought many companies to ruin, or caused the loss of much money squandered on machinery adapted only to temporary conditions.

Jan 1, 1899

By Granville S. Borden

The fruits of industry are divided between capital, labor, and governments. Capital takes its redemption and remuneration through profits or dividends; labor takes its share through wages; governments take their share through taxes. Each must have a just share, and the question of what is a just share and the question of who-shall make the allocation are vital current political and economic issues. Certain political philosophies con- tend that government should take all the fruits and that some dictator or politician should have irrevocable discretion and power to distribute the fruits. Believers in democracy and free enterprise adhere to the view that capital is entitled to redemption and fair remuneration; that labor shall have a fair wage; and that governments shall make equitable levies. But since all human beings, both individually and in groups, are inherently selfish, there are many variable views in regard to the question of what ratios shall be applied in a division of the fruits and who shall have the power to fix these ratios. Perhaps all parties should devote more energy to means of increasing the crop, and not so much time to quarreling over a division of the existing crop. Moreover, all three parties must guard against killing the goose that lays the mineral eggs. For example, if the tax burden becomes oppressive and the taxpayer refuses to carry it, then business stagnates, with consequent unemployment, reduction of profits, and curtailment of government revenue. If a producer assumes the increased tax burden, marginal operations must be closed down, and again the consequences are increased unemployment and diminished government revenue. Quite often an increase in a rate of tax results in a reduction of government revenue. Perhaps the worst detrimental feature of selfishness and greed on the part of any one of the three distributees of the fruits of industry is the retardation of expansion of the enterprise. Growth means new jobs, more government revenue, better trade, and better standards of living. Explorations and discoveries have resulted in tremendous contributions

Jan 1, 1959

By J. Szekely

A rrlethod is presented for the estitnation of oxygen pickup by teettzed molten steel streams. Of the mechanisrt~s considered for oxygen absorption, physical entrainment appeared to be the most significant. The estent of this physical entrainment may be calculated by the application of boundary layer theory. It was found that the values of oxygen pickup thus predicted were in wry good agreement with data reported in the literature, in the case of short, well-defined metal streams. This entrainment model does not provide an adequate description of oxygen pickup by long streams, exoosed to external winds and where breakup of the streatn is likely. WheN molten steel is teemed into a mold or tundish it will absorb oxygen contained in its environment. Recently interest has been expressed in the measurement and possible prediction of the extent of this oxygen absorption: this interest owes its existence to two principal factors: a) the desirability of providing a quantitative assessment of the role played by the absorbed oxygen in impairing the quality of (vacuum degassed. stainless, or continuously cast) steel; b) the need for providing guidelines for stream protection methods. The purpose of this communication is to suggest a simple method for the prediction of oxygen absorption by continuous metal streams and to compare the predicted values with the data available in the literature. It is hoped that this method may provide at least an initial framework for the interpretation of additional data that might become available. FORMULATION Consider a continuous metal stream falling into a molten metal pool as depicted in Fig. 1. This system may absorb oxygen due to the following two mechanisms: 1) physical entrainment of gases (including oxygen) into the molten pool where reactions. thus absorption, will occur; 2) mass transfer (convec:tive diffusion) of oxygen to the metal stream. 1) Physical Entrainment. The physical entrainment may be calculated by using the concept of the diaplace-ttzent tlzickness of the laminar boundary layer, which will be stated briefly in the following.&apos; When a fluid flows past a solid surface, a portion of the fluid close to the surface is retarded due to fric-tional forces. This region in which the velocity of the fluid differs from that in the main stream is called the boundary layer. An illustration of this is given in Fig. 2 where it is seen that the thickness of the boundary layer increases as we move along in the x direction. In the laminar region, when Re, < 10&apos; the thickness of the boundary layer is given by the following relationship: f =4.64 Re;1" [1] where 61 is the boundary layer thickness, x is the length along the leading edge, Us is the velocity of the free stream, (i is the viscosity of the fluid (gas in this instance).

Jan 1, 1970

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-